Quad, Current-Output, Serial-Input 16-/14-Bit DACs AD5544/AD5554 FEATURES FUNCTIONAL BLOCK DIAGRAM VREFA B C D VDD D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 A0 A1 SDO SDI RFBA INPUT REGISTER R RFBB 16 INPUT REGISTER R DAC B IOUTB AGNDB RFBC INPUT REGISTER R DAC C REGISTER R DAC C IOUTC RFBD EN INPUT REGISTER R DAC A B C D 2:4 DECODE DAC D REGISTER R DAC D IOUTD AGNDD AD5544 POWER-ON RESET DGND RS MSB AGNDF VSS LDAC Figure 1. The AD5544 is packaged in the compact 28-lead SSOP and 32lead LFCSP. The AD5554 is packed in the compact 28-lead SSOP. 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 00943-002 A double-buffered serial data interface offers high speed, 3-wire, SPI- and microcontroller-compatible inputs using serial data in (SDI), a chip select (CS), and clock (CLK) signals. In addition, a serial data out pin (SDO) allows for daisy-chaining when multiple packages are used. A common, level-sensitive, load DAC strobe (LDAC) input allows the simultaneous update of all DAC outputs from previously loaded input registers. Additionally, an internal power-on reset forces the output voltage to 0 at system turn-on. The MSB pin allows system reset assertion (RS) to force all registers to zero code when MSB = 0 or to half-scale code when MSB = 1. DAC B REGISTER R CS CLK INL ERROR (LSB) The applied external reference input voltage (VREFx) determines the full-scale output current. Integrated feedback resistors (RFB) provide temperature-tracking, full-scale voltage outputs when combined with an external I-to-V precision amplifier. IOUTA AGNDA Automatic test equipment Instrumentation Digitally controlled calibration The AD5544/AD5554 quad, 16-/14-bit, current output, digitalto-analog converters (DACs) are designed to operate from a 2.7 V to 5.5 V supply range. DAC A AGNDC APPLICATIONS GENERAL DESCRIPTION DAC A REGISTER R 00943-001 AD5544: 16-bit resolution INL of 1 LSB (B Grade) AD5554: 14-bit resolution INL of 0.5 LSB (B Grade) 2 mA full-scale current 20%, with VREF = 10 V 0.9 s settling time to 0.1% 12 MHz multiplying bandwidth Midscale glitch of -1 nV-sec Midscale or zero-scale reset 4 separate, 4-quadrant multiplying reference inputs SPI-compatible, 3-wire interface Double-buffered registers enable Simultaneous multichannel change Internal power-on reset Temperature range: -40C to +125C Compact 28-lead SSOP and 32-lead LFCSP -0.1 -0.2 0 10,000 20,000 30,000 40,000 CODE 50,000 60,000 70,000 Figure 2. AD5544 INL vs. Code Plot (TA = 25C) Rev. E Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2000-2011 Analog Devices, Inc. All rights reserved. AD5544/AD5554 TABLE OF CONTENTS Features .............................................................................................. 1 Power-On Reset.......................................................................... 16 Applications....................................................................................... 1 ESD Protection Circuits ............................................................ 16 General Description ......................................................................... 1 Power Supply Sequence ............................................................. 16 Functional Block Diagram .............................................................. 1 Layout and Power Supply Bypassing ....................................... 17 Revision History ............................................................................... 2 Grounding ................................................................................... 17 Specifications..................................................................................... 3 Applications Information .............................................................. 18 AD5544 Electrical Characteristics ............................................. 3 Reference Selection .................................................................... 18 AD5554 Electrical Characteristics ............................................. 4 Amplifier Selection .................................................................... 18 Timing Diagrams.......................................................................... 6 Evaluation Board for the AD5544................................................ 20 Absolute Maximum Ratings............................................................ 7 System Demonstration Platform.............................................. 20 ESD Caution.................................................................................. 7 Operating the Evaluation Board .............................................. 20 Pin Configurations and Function Descriptions ........................... 8 Evaluation Board Schematics ................................................... 21 Typical Performance Characteristics ........................................... 10 Evaluation Board Layout........................................................... 24 Theory of Operation ...................................................................... 12 Outline Dimensions ....................................................................... 26 Digital-to-Analog Converter (DAC) ....................................... 12 Ordering Guide .......................................................................... 27 Serial Data Interface ....................................................................... 14 Truth Tables................................................................................. 15 REVISION HISTORY 6/11--Rev. D to Rev. E Added 32-Lead LFCSP.................................................. Throughout Changes to Table 1, Supply Characteristics Parameters .............. 3 Changes to Table 2, Supply Characteristics Parameters .............. 5 Added Figure 6, Renumbered Subsequent Figures, Changes to Table 4............................................................................................ 7 Changed Applications Section to Applications Information Section, Added Reference Selection and Amplifier Selection Sections ............................................................................................ 19 Added Evaluation Board for the AD5544 Section ..................... 21 Updated Outline Dimensions ....................................................... 17 Changes to Ordering Guide .......................................................... 18 9/09--Rev. C to Rev. D Changes to Features Section............................................................ 1 Changes to Table 1............................................................................ 3 Changes to Table 2............................................................................ 4 Changes to Figure 12........................................................................ 9 Changes to Figure 19...................................................................... 10 Changes to Table 8 and Table 9..................................................... 13 Changes to Ordering Guide .......................................................... 16 8/09--Rev. B to Rev. C Change to Table 1 ............................................................................. 3 Change to Table 2 ............................................................................. 4 Changes to Features Section ............................................................1 Changes to Figure 2...........................................................................1 Changes to Table 1.............................................................................3 Changes to Table 2.............................................................................4 Moved Timing Diagram...................................................................5 Added Figure 4; Renumbered Sequentially ...................................5 Change to Table 3 ..............................................................................6 Changes to Table 4.............................................................................7 Changes to Typical Performance Characteristics Section ...........8 Changes to Figure 19...................................................................... 10 Moved Table 5, Table 6, and Table 7 ............................................ 12 Moved Truth Tables Section ......................................................... 13 Deleted Figure 27; Renumbered Sequentially ............................ 14 Updated Outline Dimensions....................................................... 16 Changes to Ordering Guide .......................................................... 16 12/04--Rev. 0 to Rev. A Updated Format..................................................................Universal Change to Electrical Characteristics Tables ...................................4 Change to Pin Description Table.................................................. 10 Addition of Power Supply Sequence Section.............................. 19 Addition of Layout and Power Supply Bypassing Section ........ 19 Addition of Grounding Section.................................................... 19 Addition of Figure 32..................................................................... 19 4/00--Revision 0: Initial Version 8/09--Rev. A to Rev. B Rev. E | Page 2 of 28 AD5544/AD5554 SPECIFICATIONS AD5544 ELECTRICAL CHARACTERISTICS VDD = 2.7 V to 5.5 V, VSS = 0 V, IOUTx = virtual GND, AGNDx = 0 V, VREFA = VREFB = VREFC = VREFD = 10 V, TA = full operating temperature range of -40C to +125C, unless otherwise noted. Table 1. Parameter STATIC PERFORMANCE 1 Resolution Relative Accuracy Symbol Test Condition/Comments N INL 1 LSB = VREFx/216 = 153 V when VREF = 10 V AD5544BRSZ AD5544ARSZ AD5544BCPZ AD5544ACPZ-1 AD5544BRSZ AD5544ARSZ AD5544BCPZ AD5544ACPZ-1 Data = 0x0000, TA = 25C Data = 0x0000, TA = 85C Data = 0xFFFF Differential Nonlinearity DNL Output Leakage Current IOUTx Full-Scale Gain Error Full-Scale Tempco 2 Feedback Resistor REFERENCE INPUT VREFx Range Input Resistance Input Resistance Match Input Capacitance2 ANALOG OUTPUT Output Current Output Capacitance2 LOGIC INPUT AND OUTPUT Logic Input Low Voltage Logic Input High Voltage Input Leakage Current Input Capacitance2 Logic Output Low Voltage Logic Output High Voltage INTERFACE TIMING2, 3 Clock Width High Clock Width Low CS to Clock Setup Clock to CS Hold Clock to SDO Propagation Delay Load DAC Pulse Width Data Setup Data Hold Load Setup Load Hold SUPPLY CHARACTERISTICS Power Supply Range Positive Supply Current Negative Supply Current GFSE TCVFS RFBx VREFx RREFx RREFx CREFx VDD = 5 V Min 4 0.75 1 6 Max Unit 16 1 2 1 4 1 1.5 1 1 10 20 3 Bits LSB LSB LSB LSB LSB LSB LSB LSB nA nA mV ppm/C k 8 +15 8 V k % pF 2.5 mA pF 0.8 4 V V A pF V V tCH tCL tCSS tCSH tPD 25 25 0 25 2 ns ns ns ns ns tLDAC tDS tDH tLDS tLDH 25 20 20 5 25 IOUTx COUTx VIL VIH IIL CIL VOL VOH VDD RANGE IDD ISS -15 4 Typ Channel-to-channel Data = 0xFFFF Code dependent 6 0.35 5 1.25 35 2.4 1 10 0.4 IOL = 1.6 mA IOH = 100 A 20 ns ns ns ns ns 2.7 Logic inputs = 0 V Logic inputs = 0 V, VSS = -5 V Rev. E | Page 3 of 28 0.001 5.5 5 9 V A A AD5544/AD5554 Parameter Power Dissipation Power Supply Sensitivity AC CHARACTERISTICS 4 Output Voltage Settling Time Reference Multiplying Bandwidth (BW) DAC Glitch Impulse Feedthrough Error Crosstalk Error Digital Feedthrough Total Harmonic Distortion Output Spot Noise Voltage Symbol PDISS PSS Test Condition/Comments Logic inputs = 0 V VDD = 5% tS BW - 3 dB To 0.1% of full scale, data = 0x0000 to 0xFFFF to 0x0000 VREFx = 5 V p-p, data = 0xFFFF, CFB = 2.0 pF, 0.9 12 s MHz Q VOUTx/VREFx VOUTA/VREFB VREFx = 8 V, data = 0x0000 to 0x8000 to 0x0000 Data = 0x0000, VREFx = 100 mV rms, f = 100 kHz Data = 0x0000, VREFB = 100 mV rms, adjacent channel, f = 100 kHz CS = 1, fCLK = 1 MHz VREFx = 5 V p-p, data = 0xFFFF, f = 1 kHz f = 1 kHz, BW = 1 Hz -1 -65 -90 nV-sec dB dB 0.6 -98 7 nV-sec dB nV/Hz Q THD eN Min Typ Max 1.25 0.006 Unit mW %/% 1 All static performance tests (except IOUTx) are performed in a closed-loop system using an external precision OP177 I-to-V converter amplifier. The AD5544 RFB terminal is tied to the amplifier output. Typical values represent average readings measured at 25C. 2 These parameters are guaranteed by design and not subject to production testing. 3 All input control signals are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V. 4 All ac characteristic tests are performed in a closed-loop system using an AD8038 I-to-V converter amplifier. AD5554 ELECTRICAL CHARACTERISTICS VDD = 2.7 V to 5.5 V, VSS = 0 V, IOUTx = virtual GND, AGNDx = 0 V, VREFA = VREFB = VREFC = VREFD = 10 V, TA = full operating temperature range of -40C to +125C, unless otherwise noted. Table 2. Parameter STATIC PERFORMANCE 1 Resolution Relative Accuracy Differential Nonlinearity Output Leakage Current Full-Scale Gain Error Full-Scale Tempco 2 Feedback Resistor REFERENCE INPUT VREFx Range Input Resistance Input Resistance Match Input Capacitance2 ANALOG OUTPUT Output Current Output Capacitance2 LOGIC INPUT AND OUTPUT Logic Input Low Voltage Logic Input High Voltage Input Leakage Current Input Capacitance2 Logic Output Low Voltage Logic Output High Voltage INTERFACE TIMING2, 3 Clock Width High Clock Width Low CS to Clock Setup Clock to CS Hold Symbol Test Condition/Comments N INL DNL IOUTx 1 LSB = VREFx/214 = 610 V when VREFx = 10 V GFSE TCVFS RFBx VREFx RREFx RREFx CREFx IOUTx COUTx VIL VIH IIL CIL VOL VOH Min Data = 0x0000, TA = 25C Data = 0x0000, TA = 85C Data = 0x3FFF VDD = 5 V 4 -15 4 2 1 6 Max Unit 14 0.5 1 10 20 10 Bits LSB LSB nA nA mV ppm/C k 8 +15 8 V k % pF 2.5 mA pF 0.8 4 V V A pF V V 25 25 0 25 ns ns ns ns Channel-to-channel Data = 0x3FFF Code dependent Typ 6 1 5 1.25 80 2.4 1 10 0.4 IOL = 1.6 mA IOH = 100 A tCH tCL tCSS tCSH Rev. E | Page 4 of 28 AD5544/AD5554 Parameter Clock to SDO Propagation Delay Load DAC Pulse Width Data Setup Data Hold Load Setup Load Hold SUPPLY CHARACTERISTICS Power Supply Range Positive Supply Current Negative Supply Current Power Dissipation Power Supply Sensitivity AC CHARACTERISTICS 4 Output Voltage Settling Time Reference Multiplying Bandwidth (BW) DAC Glitch Impulse Feedthrough Error Crosstalk Error Digital Feedthrough Total Harmonic Distortion Output Spot Noise Voltage Symbol tPD Test Condition/Comments tLDAC tDS tDH tLDS tLDH Min 2 Typ Max 20 25 20 20 5 25 Unit ns ns ns ns ns ns VDD RANGE IDD ISS PDISS PSS Logic inputs = 0 V Logic inputs = 0 V, VSS = -5 V Logic inputs = 0 V VDD = 5% tS BW - 3 dB To 0.1% of full scale, data = 0x0000 to 0x3FFF to 0x0000 VREFx = 5 V p-p, data = 0xFFFF, CFB = 2.0 pF 0.9 12 s MHz Q VOUTx/VREFx VOUTA/VREFB VREFx = 8 V, data = 0x0000 to 0x2000 to 0x0000 Data = 0x0000, VREFx = 100 mV rms, f = 100 kHz Data = 0x0000, VREFB = 100 mV rms, adjacent channel, f = 100 kHz CS = 1, fCLK = 1 MHz VREFx = 5 V p-p, data = 0x3FFF, f = 1 kHz f = 1 kHz, BW = 1 Hz -1 -65 -90 nV-sec dB dB 0.6 -98 7 nV-sec dB nV/Hz Q THD eN 2.7 1 0.001 5.5 5 9 1.25 0.006 V A A mW %/% All static performance tests (except IOUT) are performed in a closed-loop system using an external precision OP177 I-to-V converter amplifier. The AD5554 RFB terminal is tied to the amplifier output. Typical values represent average readings measured at 25C. These parameters are guaranteed by design and not subject to production testing. 3 All input control signals are specified with tR = tF = 2.5 ns (10% to 90% of 3 V) and timed from a voltage level of 1.5 V. 4 All ac characteristic tests are performed in a closed-loop system using an AD8038 I-to-V converter amplifier,. 2 Rev. E | Page 5 of 28 AD5544/AD5554 TIMING DIAGRAMS SDI A1 A0 D15 D14 D13 D12 D11 D10 D1 D0 INPUT REG LD CLK tDS tCSS CS tDH tCH tCL tCSH tLDS LDAC tLDH tLDAC 00943-004 tPD SDO Figure 3. AD5544 Timing Diagram A1 A0 D13 D12 D11 D10 D09 D08 D1 D0 INPUT REG LD CLK CS tCSS tDS tDH tCH tCL tCSH tLDS LDAC tPD SDO Figure 4. AD5554 Timing Diagram Rev. E | Page 6 of 28 tLDH tLDAC 00943-005 SDI AD5544/AD5554 ABSOLUTE MAXIMUM RATINGS Table 3. Parameter VDD to GND VSS to GND VREFx to GND Logic Input and Output to GND V(IOUTx) to GND AGNDx to DGND Input Current to Any Pin Except Supplies Package Power Dissipation Thermal Resistance 28-Lead SSOP 32-Lead LFCSP Maximum Junction Temperature (TJ Max) Operating Temperature Range Storage Temperature Range Lead Temperature Vapor Phase, 60 Sec Infrared, 15 Sec Rating -0.3 V, +8 V +0.3 V, -7 V -18 V, +18 V -0.3 V, +8 V -0.3 V, VDD + 0.3 V -0.3 V, +0.3 V 50 mA (TJ max - TA)/JA JA 100C/W 32.5C/W 150C -40C to +125C -65C to +150C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION 215C 220C Rev. E | Page 7 of 28 AD5544/AD5554 27 I OUTD VREF A 3 26 V REF D RFBA 4 25 RFBD MSB 5 24 DGND RS 6 AD5544/ AD5554 VDD 7 1 2 3 4 5 6 7 CS 8 AGNDA IOUTA VREF A RFBA MSB RS VDD 23 VSS 22 AGNDF TOP VIEW 21 LDAC (Not to Scale) 20 SDO 18 R C FB VREF B 12 17 V REF C IOUTB 13 16 I OUTC AGNDB 14 15 AGNDC NC = NO CONNECT DGND VSS AGNDF LDAC SDO NC RFBC VREF C 9 10 11 12 13 14 15 16 19 NC AD5544 TOP VIEW (Not to Scale) 24 23 22 21 20 19 18 17 CLK SDI RFBB VREF B IOUTB AGNDB AGNDC IOUTC SDI 10 RFBB 11 NOTES 1. NC = NO CONNECT. 2. CONNECT EXPOSED PAD TO AGND. 00943-003 CS 8 CLK 9 32 31 30 29 28 27 26 25 28 A GNDD IOUTA 2 00943-035 AGNDA 1 NC NC NC NC AGNDD IOUTD VREF D RFBD PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 6. LFCSP Pin Configuration Figure 5. TSSOP Pin Configuration Table 4. Pin Function Descriptions TSSOP Pin No. 1 2 3 LFCSP Pin No. 1 2 3 Mnemonic AGNDA IOUTA VREFA 4 5 6 4 5 6 RFBA MSB RS 7 8 7 8 VDD CS 9 10 11 12 9 10 11 12 CLK SDI RFBB VREFB 13 14 15 16 17 13 14 15 16 17 IOUTB AGNDB AGNDC IOUTC VREFC 18 19 20 18 19 20 RFBC NC SDO 21 21 LDAC 22 23 24 25 22 23 24 25 AGNDF VSS DGND RFBD Description DAC A Analog Ground. DAC A Current Output. DAC A Reference Voltage Input Terminal. Establishes DAC A full-scale output voltage. This pin can be tied to the VDD pin. Establish the voltage output for DAC A by connecting to an external amplifier output. MSB Bit. Set pin during a reset pulse (RS) or at system power-on if tied to ground or VDD. Reset Pin, Active Low Input. Input registers and DAC registers are set to all 0s or half-scale code (0x8000 for the AD5544 and 0x2000 for the AD5554), determined by the voltage on the MSB pin. Register data = 0x0000 when MSB = 0. Positive Power Supply Input. Specified range of operation: 5 V 10%. Chip Select, Active Low Input. Disables shift register loading when high. Transfers serial register data to the input register when CS/LDAC returns high. Does not affect LDAC operation. Clock Input. Positive edge clocks data into the shift register. Serial Data Input. Input data loads directly into the shift register. Establish the voltage output for DAC B by connecting to an external amplifier output. DAC B Reference Voltage Input Terminal. Establishes DAC B full-scale output voltage. This pin can be tied to the VDD pin. DAC B Current Output. DAC B Analog Ground. DAC C Analog Ground. DAC C Current Output. DAC C Reference Voltage Input Terminal. Establishes DAC C full-scale output voltage. This pin can be tied to the VDD pin. Establish the voltage output for DAC C by connecting to an external amplifier output. No Connect. Leave the pin unconnected. Serial Data Output. Input data loads directly into the shift register. Data appears at SDO at 19 clock pulses for the AD5544 and 17 clock pulses for the AD5554 after input at the SDI pin. Load DAC Register Strobe, Level Sensitive Active Low. Transfers all input register data to DAC registers. Asynchronous active low input. See Table 8 and Table 9 for operation. High Current Analog Force Ground. Negative Bias Power Supply Input. Specified range of operation: -5.5 V to +0.3 V. Digital Ground Pin. Establish the voltage output for DAC D by connecting to an external amplifier output. Rev. E | Page 8 of 28 AD5544/AD5554 TSSOP Pin No. 26 LFCSP Pin No. 26 Mnemonic VREFD 27 28 N/A N/A N/A N/A N/A 27 28 29 30 31 32 33 IOUTD AGNDD NC NC NC NC EPAD Description DAC D Reference Voltage Input Terminal. Establishes DAC D full-scale output voltage. This pin can be tied to the VDD pin. DAC D Current Output. DAC D Analog Ground. Do not connect. Do not connect. Do not connect. Do not connect. Connect the exposed pad to AGNDx. Rev. E | Page 9 of 28 AD5544/AD5554 TYPICAL PERFORMANCE CHARACTERISTICS 1.5 0.10 1.0 0xF000 -0.05 0.5 -0.10 INL (LSB) -0.15 -0.20 0 10,000 20,000 30,000 40,000 CODE 50,000 60,000 -1.5 -2000 70,000 0.15 0.75 0.10 0.50 0.05 0.25 DNL (LSB) 1.00 0 -0.05 500 1000 1500 2000 -0.75 00943-007 -0.15 -1.00 -1000 8000 10,000 12,000 14,000 16,000 18,000 CODE 0x0FFF 0xF000 -0.25 -0.50 6000 0 VDD = 5V VREF = 10V 0 -0.10 4000 -500 Figure 10. AD5544 Integral Nonlinearity Error vs. Op Amp Offset 0.20 2000 -1000 OFFSET VOLTAGE (V) Figure 7. AD5544 DNL vs. Code, TA = 25C 0 -1500 00943-009 00943-006 -1.0 -0.35 -0.20 0x8000 -0.5 -0.25 -0.30 INL ERROR (LSB) 0x7FFF 0 0x8000 -750 -500 -250 0 250 500 750 1000 OP AMP OFFSET (V) 00943-0 11 DNL ERROR (LSB) 0 -0.40 VDD = 5V VREF = 10V 0x0FFF 0.05 Figure 11. AD5544 Differential Nonlinearity Error vs. Op Amp Offset Figure 8. AD5554 INL vs. Code, TA = 25C 10 0.10 VDD = 5V VREF = 10V 5 GAIN ERROR (LSB) 0 -0.05 -0.10 -5 -10 0 2000 4000 6000 8000 10,000 12,000 14,000 16,000 18,000 CODE -20 -1500 -1000 -500 0 500 1000 OP AMP OFFSET (V) Figure 12. AD5544 Gain Error vs. Op Amp Offset Figure 9. AD5554 DNL vs. Code, TA = 25C Rev. E | Page 10 of 28 1500 00943-013 -0.15 0 -15 00943-008 DNL ERROR (LSB) 0.05 AD5544/AD5554 10,000 -3.88 -3.90 -3.92 1000 -3.96 IDD (A) VOUT (V) -3.94 -3.98 -4.00 ZERO SCALE MIDSCALE FULL SCALE 0x5555 100 -4.02 10 -4.04 1 1k 0.4 0.5 0.6 0.7 0.8 0.9 TIME (s) 1.0 1.1 1.2 00943-012 -4.08 Figure 13. AD5544 Midscale Transition 10k 100M 10M 100k 1M CLOCK FREQUENCY (Hz) 00943-015 -4.06 Figure 16. AD5544 Power Supply Current vs. Clock Frequency 100 VDD = 5V VREF = 10V VDD = 5V VREF = 10V 90 80 VOUT PSRR (dB) 5V/DIV 70 LDAC 60 50 40 30 00943- 018 20 0 100 1k 10k 100k 1M FREQUENCY (Hz) Figure 14. AD5544 Large Signal Settling Time Figure 17. AD5544/AD5554 Power Supply Rejection vs. Frequency 4 300 0 250 -12 0 2 4 6 8 TIME (s) Figure 15. AD5544 Small Signal Settling Time 150 100 -16 50 -20 10 0 00943-019 -0.1 200 0 0.5 1.0 1.5 2.0 2.5 3.0 LOGIC INPUT (V) 3.5 4.0 4.5 5.0 00943-017 VOUT (V) -8 LDAC (V) -4 0 -0.2 -2 SUPPLY CURRENT (A) 0.1 00943-020 10 Figure 18. AD5544/AD5554 Power Supply Current vs. Logic Input Voltage Rev. E | Page 11 of 28 AD5544/AD5554 THEORY OF OPERATION DIGITAL-TO-ANALOG CONVERTER (DAC) Each part contains four current-steering R-R ladder DACs. Figure 19 shows a typical equivalent DAC. Each DAC contains a matching feedback resistor for use with an external I-to-V converter amplifier. The RFBx pin connects to the output of the external amplifier. The IOUTx terminal connects to the inverting input of the external amplifier. The AGNDx pin should be Kelvinconnected to the load point, requiring full 16-bit accuracy. These DACs are designed to operate with both negative and positive reference voltage. The VDD power pin is used only by the logic to drive the DAC switches on and off. Note that a matching switch is used in series with the internal 5 k feedback resistor. If users attempt to measure the value of RFB, power must be applied to VDD to achieve continuity. An additional VSS bias pin is used to guard the substrate during high temperature applications, minimizing zero-scale leakage currents that double every 10C. The DAC output voltage is determined by VREF and the digital data (D) in the following equations: VOUT = - VREF D (for the AD 5544) x 65,536 (1) D (for the AD 5554) 16,384 (2) VOUT = - VREF x These DACs are also designed to accommodate ac reference input signals. Both the AD5544 and the AD5554 accommodate input reference voltages in the range of -15 V to +15 V. The reference voltage inputs exhibit a constant nominal input resistance of 5 k 30%. On the other hand, the IOUTA, IOUTB, IOUTC, and IOUTD DAC outputs are code dependent and produce various output resistances and capacitances. The choice of external amplifier should take into account the variation in impedance generated by the AD5544/AD5554 on the inverting input node of the amplifier. The feedback resistance, in parallel with the DAC ladder resistance, dominates output voltage noise. For multiplying mode applications, an external feedback compensation capacitor, CFB, may be needed to provide a critically damped output response for step changes in reference input voltages. Figure 20 shows the gain vs. frequency performance at various attenuation settings using a 23 pF external feedback capacitor connected across the IOUTx and RFBx terminals for the AD5544 and the AD5554, respectively. To maintain good analog performance, power supply bypassing of 0.01 F, in parallel with 1 F, is recommended. Under these conditions, a clean power supply with low ripple voltage capability should be used. Switching power supplies is usually not suitable for this application due to the higher ripple voltage and PSS frequency-dependent characteristics. It is best to derive the supply of the AD5544/AD5554 from system analog supply voltages. Do not use the digital supply (see Figure 21). 2 0 GAIN (dB) The AD5544 and the AD5554 contain four 16-bit and 14-bit, current output DACs, respectively. Each DAC has its own independent multiplying reference input. Both the AD5544 and the AD5554 use a 3-wire, SPI-compatible serial data interface, with a configurable asynchronous RS pin for half-scale (MSB = 1) or zero-scale (MSB = 0) preset. In addition, an LDAC strobe enables 4-channel, simultaneous updates for hardware synchronized output voltage changes. Note that the output polarity is opposite the VREF polarity for dc reference voltages. -2 -4 -6 2R R R 2R 2R -8 100k RFBX R 5k S2 10M 100M FREQUENCY (Hz) Figure 20. AD5554 Reference Multiplying Bandwidth vs. Code S1 IOUTX AGNDF AGNDX FROM OTHER DACS AGND DGND DIGITAL INTERFACE CONNECTIONS OMITTED FOR CLARITY. SWITCHES S1 AND S2 ARE CLOSED, AND VDD MUST BE POWERED. 00943-025 VSS 1M Figure 19. Typical Equivalent DAC Channel Rev. E | Page 12 of 28 00943-026 VDD R VREF X AD5544/AD5554 15V 2R 5V + ANALOG POWER SUPPLY R VDD AD5544 RR VREF X 2R R 2R 2R R RFBX 5k 15V S2 S1 VCC IOUTX AGNDF AGNDX VOUT A1 + VEE FROM OTHER DACS AGND LOAD DIGITAL INTERFACE CONNECTIONS OMITTED. FOR CLARITY SWITCHES S1 AND S2 ARE CLOSED, AND VDD MUST BE POWERED. Figure 21. Recommended Kelvin-Sensed Hookup Rev. E | Page 13 of 28 00943-028 DGND VSS AD5544/AD5554 SERIAL DATA INTERFACE The AD5544/AD5554 use a 3-wire (CS, SDI, CLK), SPI-compatible serial data interface. Serial data of the AD5544/AD5554 is clocked into the serial input register in an 18-bit and 16-bit data-word format, respectively. The MSB bits are loaded first. Table 5 defines the 18 data-word bits for the AD5544, and Table 6 defines the 16 data-word bits for the AD5554. Data is placed on the SDI pin and clocked into the register on the positive clock edge of CLK, subject to the data setup and data hold time requirements specified in the interface timing specifications (see Table 1 and Table 2). Similarly, two right-justified data bytes can be written to the AD5554. Keeping the CS line low between the first and second byte transfer results in a successful serial register update. Data can be clocked in only while the CS chip select pin is active low. For the AD5544, only the last 18 bits clocked into the serial register are interrogated when the CS pin returns to the logic high state; extra data bits are ignored. For the AD5554, only the last 16 bits clocked into the serial register are interrogated when the CS pin returns to the logic high state. Because most microcontrollers output serial data in 8-bit bytes, three right-justified data bytes can be written to the AD5544. Keeping the CS line low between the first, second, and third byte transfers results in a successful serial register update. For the AD5554, Table 6, Table 7, Table 9, and Figure 4 define the characteristics of the software serial interface. Figure 22 and Figure 23 show the equivalent logic interface for the key digital control pins for the AD5544. The AD5554 has a similar configuration, except that it has 14 data bits. Two additional pins, RS and MSB, provide hardware control over the preset function and DAC register loading. If these functions are not needed, the RS pin can be tied to logic high. The asynchronous input RS pin forces all input and the DAC registers to either the zero-code state (MSB = 0) or the half-scale state (MSB = 1). When the data is properly aligned in the shift register, the positive edge of the CS initiates the transfer of new data to the target DAC register, determined by the decoding of Address Bit A1 and Address Bit A0. For the AD5544, Table 5, Table 7, Table 8, and Figure 3 define the characteristics of the software serial interface. Table 5. AD5544 Serial Input Register Data Format (Data Is Loaded in the MSB-First Format) 1 MSB B17 A1 1 B16 A0 B15 D15 B14 D14 B13 D13 B12 D12 B11 D11 B10 D10 B9 D9 B8 D8 B7 D7 B6 D6 B5 D5 B4 D4 B3 D3 B2 D2 B1 D1 LSB B0 D0 Only the last 18 bits of data clocked into the serial register (address + data) are inspected when the positive edge of the CS line returns to logic high. At this point, an internally generated load strobe transfers the serial register data contents (Bit D15 to Bit D0) to the decoded DAC input register address determined by Bit A1 and Bit A0. Any extra bits clocked into the AD5544 shift register are ignored; only the last 18 bits clocked in are used. If double-buffered data is not needed, the LDAC pin can be tied logic low to disable the DAC registers. Table 6. AD5554 Serial Input Register Data Format (Data Is Loaded in the MSB-First Format) 1 MSB B15 A1 1 B14 A0 B13 D13 B12 D12 B11 D11 B10 D10 B9 D9 B8 D8 B7 D7 B6 D6 B5 D5 B4 D4 B3 D3 B2 D2 B1 D1 LSB B0 D0 Only the last 16 bits of data clocked into the serial register (address + data) are inspected when the positive edge of the CS line returns to logic high. At this point, an internally generated load strobe transfers the serial register data contents (Bit D13 to Bit D0) to the decoded DAC input register address determined by Bit A1 and Bit A0. Any extra bits clocked into the AD5554 shift register are ignored; only the last 16 bits clocked in are used. If double-buffered data is not needed, the LDAC pin can be tied logic low to disable the DAC registers. Table 7. Address Decode A1 0 0 1 1 A0 0 1 0 1 DAC Decoded DAC A DAC B DAC C DAC D Rev. E | Page 14 of 28 AD5544/AD5554 TRUTH TABLES Table 8. AD5544 1 Control Logic Truth Table LDAC RS +3 High High High + High Low High High High High High CS High Low Low Low 3 High High High MSB 2 X X X Serial Shift Register Function 3 No effect No effect Shift register data advanced one bit Input Register Function Latched Latched Latched DAC Register Latched Latched Latched High High High High X X No effect No effect Latched Latched X X X Low High +3 High High High X X X No effect No effect No effect Latched Selected DAC updated with current shift register contents 4 Latched Latched Latched X X High High Low Low 0 High No effect No effect Latched data = 0x0000 Latched data = 0x8000 Latched data = 0x0000 Latched data = 0x8000 CLK X Low Transparent Latched Latched 1 For the AD5544, data appears at the SDO pin 19 clock pulses after input at the SDI pin. X = don't care. 3 + is a positive logic transition. 4 At power-on, both the input register and the DAC register are loaded with all 0s. 2 Table 9. AD5554 1 Control Logic Truth Table CS CLK LDAC RS MSB 2 Serial Shift Register Function 3 Input Register Function3 DAC Register High Low Low X L +3 High High High High High High X X X No effect No effect Shift register data advanced one bit Latched Latched Latched Latched Latched Latched +3 High Low High High High High X X No effect No effect Latched Latched High High High X X X Low High +3 High High High X X X No effect No effect No effect Latched Selected DAC updated with current shift register contents 4 Latched Latched Latched Transparent Latched Latched High High X X High High Low Low 0 High No effect No effect Latched data = 0x0000 Latched data = 0x2000 Latched data = 0x0000 Latched data = 0x2000 Low 1 For the AD5554, data appears at the SDO pin 17 clock pulses after input at the SDI pin. X = don't care. 3 + is a positive logic transition. 4 At power-on, both the input register and the DAC register are loaded with all 0s. 2 Rev. E | Page 15 of 28 AD5544/AD5554 VREF A B C D CS AD5544 EN VDD CLK SDI SDO D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 D14 D15 A0 A1 RFBA 16 INPUT REGISTER R DAC A REGISTER R DAC A IOUTA AGNDA RFBB INPUT REGISTER R DAC B REGISTER R DAC B IOUTB AGNDB DAC A B C D 2:4 DECODE RFBC INPUT REGISTER R DAC C REGISTER R DAC C IOUTC AGNDC RFBD INPUT REGISTER R DAC D REGISTER R DAC D IOUTD AGNDD SET MSB SET MSB DGND MSB LDAC 00943-029 AGNDF POWERON RESET VSS RS Figure 22. System Level Digital Interfacing ESD PROTECTION CIRCUITS TO INPUT REGISTER All logic input pins contain back-biased ESD protection Zener diodes that are connected to ground (DGND) and VDD, as shown in Figure 24. EN VDD SHIFT REGISTER SDI 19TH/17TH CLOCK SDO DIGITAL INPUTS 5k 00943-030 CLK DGND Figure 23. AD5544/AD5554 Equivalent Logic Interface 00943-031 ADDRESS DECODER CS A B C D Figure 24. Equivalent ESD Production Circuits POWER-ON RESET When the VDD power supply is turned on, an internal reset strobe forces all the input and DAC registers to the zero-code state or half-scale state, depending on the MSB pin voltage. The VDD power supply should have a smooth positive ramp without drooping to have consistent results, especially in the region of VDD = 1.5 V to 2.3 V. The VSS supply has no effect on the power-on reset performance. The DAC register data stays at a zero-scale or half-scale setting until a valid serial register data load takes place. POWER SUPPLY SEQUENCE As standard practice, it is recommended that VDD, VSS, and ground be powered up prior to any reference. The ideal power-up sequence is as follows: AGNDx, DGND, VDD, VSS, VREFx, and the digital inputs. A noncompliance power-up sequence may elevate the reference current, but the devices resume normal operation once VDD and VSS are powered up. Rev. E | Page 16 of 28 AD5544/AD5554 AD5544/AD5554 LAYOUT AND POWER SUPPLY BYPASSING VDD It is good practice to employ a compact, minimum lead length layout design. The leads to the input should be as direct as possible with a minimum conductor length. Ground paths should have low resistance and low inductance. C4 10F + C1 0.1F C2 0.1F VDD AGNDX VSS DGND 00943-032 Similarly, it is good practice to bypass the power supplies with quality capacitors for optimum stability. Supply leads to the device should be bypassed with 0.01 F to 0.1 F disc or chip ceramic capacitors. Low ESR 1 F to 10 F tantalum or electrolytic capacitors should also be applied at VDD to minimize any transient disturbance and filter any low frequency ripple (see Figure 25). Users should not apply switching regulators for VDD due to the power supply rejection ratio (PSRR) degradation over frequency. VSS C3 10F Figure 25. Power Supply Bypassing and Grounding Connection GROUNDING The DGND and AGNDx pins of the AD5544/AD5554 serve as digital and analog ground references. To minimize the digital ground bounce, the DGND terminal should be joined remotely at a single point to the analog ground plane (see Figure 25). Rev. E | Page 17 of 28 AD5544/AD5554 REFERENCE SELECTION APPLICATIONS INFORMATION The AD5544/AD5554 are, inherently, two-quadrant multiplying DACs. That is, they can be easily set up for unipolar output operation. The full-scale output polarity is the inverse of the reference input voltage. In some applications, it may be necessary to generate the full four-quadrant multiplying capability or a bipolar output swing. This is easily accomplished using an additional external amplifier (A2) configured as a summing amplifier (see Figure 26). 10k 10k 10V 5k VREF A2 VOUT AD588 -10V < VOUT < +10V VREFX ONE CHANNEL RFBX IOUTX AD5544 VSS AGNDF A1 AGNDX DIGITAL INTERFACE CONNECTIONS OMITTED FOR CLARITY. 00943-0-033 VDD Figure 26. Four-Quadrant Multiplying Application Circuit In this circuit, the first and second amplifiers (A1 and A2) provide a total gain of 2, which increases the output voltage span to 20 V. Biasing the external amplifier with a 10 V offset from the reference voltage results in a full four-quadrant multiplying circuit. The transfer equation of this circuit shows that both negative and positive output voltages are created as the input data (D) is incremented from code zero (VOUT = -10 V) to midscale (VOUT = 0 V) to full scale (VOUT = 10 V). D VOUT - 1 x - VREF (for the AD 5544) 32,768 (3) D VOUT - 1 x - VREF (for the AD 5554 ) 8192 (4) When selecting a reference for use with the AD55xx series of current output DACs, pay attention to the output voltage, temperature coefficient specification of the reference. Choosing a precision reference with a low output temperature coefficient minimizes error sources. Table 10 lists some of the references available from Analog Devices, Inc., that are suitable for use with this range of current output DACs. AMPLIFIER SELECTION The primary requirement for the current-steering mode is an amplifier with low input bias currents and low input offset voltage. Because of the code-dependent output resistance of the DAC, the input offset voltage of an op amp is multiplied by the variable gain of the circuit. A change in this noise gain between two adjacent digital fractions produces a step change in the output voltage due to the amplifier's input offset voltage. This output voltage change is superimposed upon the desired change in output between the two codes and gives rise to a differential linearity error, which, if large enough, can cause the DAC to be nonmonotonic. The input bias current of an op amp also generates an offset at the voltage output because of the bias current flowing in the feedback resistor, RFB. Common-mode rejection of the op amp is important in voltageswitching circuits because it produces a code-dependent error at the voltage output of the circuit. Provided that the DAC switches are driven from true wideband, low impedance sources (VIN and AGND), they settle quickly. Consequently, the slew rate and settling time of a voltage-switching DAC circuit is determined largely by the output op amp. To obtain minimum settling time in this configuration, minimize capacitance at the VREF node (the voltage output node in this application) of the DAC. This is done by using low input capacitance buffer amplifiers and careful board design. Analog Devices offers a wide range of amplifiers for both precision dc and ac applications, as listed in Table 11 and Table 12. Rev. E | Page 18 of 28 AD5544/AD5554 Table 10. Suitable Analog Devices Precision References Part No. ADR01 ADR01 ADR02 ADR02 ADR03 ADR03 ADR06 ADR06 ADR420 ADR421 ADR423 ADR425 ADR431 ADR435 ADR391 ADR395 Output Voltage (V) 10 10 5.0 5.0 2.5 2.5 3.0 3.0 2.048 2.50 3.00 5.00 2.500 5.000 2.5 5.0 Initial Tolerance (%) 0.05 0.05 0.06 0.06 0.1 0.1 0.1 0.1 0.05 0.04 0.04 0.04 0.04 0.04 0.16 0.10 Maximum Temperature Drift (ppm/C) 3 9 3 9 3 9 3 9 3 3 3 3 3 3 9 9 ISS (mA) 1 1 1 1 1 1 1 1 0.5 0.5 0.5 0.5 0.8 0.8 0.12 0.12 Output Noise (V p-p) 20 20 10 10 6 6 10 10 1.75 1.75 2 3.4 3.5 8 5 8 Package(s) SOIC-8 TSOT-5, SC70-5 SOIC-8 TSOT-5, SC70-5 SOIC-8 TSOT-5, SC70-5 SOIC-8 TSOT-5, SC70-5 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 SOIC-8, MSOP-8 TSOT-5 TSOT-5 Table 11. Suitable Analog Devices Precision Op Amps Part No. OP97 OP1177 AD8675 AD8671 ADA4004-1 AD8603 AD8607 AD8605 AD8615 AD8616 Supply Voltage (V) 2 to 20 2.5 to 15 5 to 18 5 to 15 5 to 15 1.8 to 5 1.8 to 5 2.7 to 5 2.7 to 5 2.7 to 5 VOS Maximum (V) 25 60 75 75 125 50 50 65 65 65 IB Maximum (nA) 0.1 2 2 12 90 0.001 0.001 0.001 0.001 0.001 0.1 Hz to 10 Hz Noise (V p-p) 0.5 0.4 0.1 0.077 0.1 2.3 2.3 2.3 2.4 2.4 Supply Current (A) 600 500 2300 3000 2000 40 40 1000 2000 2000 Package(s) SOIC-8, PDIP-8 MSOP-8, SOIC-8 MSOP-8, SOIC-8 MSOP-8, SOIC-8 SOIC-8, SOT-23-5 TSOT-5 MSOP-8, SOIC-8 WLCSP-5, SOT-23-5 TSOT-5 MSOP-8, SOIC-8 VOS (Max) (V) 1500 1500 1000 5000 3000 35 5000 5000, 6000 6000 10,000 IB (Max) (nA) 0.006 0.006 10,500 15,000 750 100 500 500 350 350 7000 Package(s) SOIC-8, SOT-23-5 SOIC-8, MSOP-8 SOIC-8, MSOP-8 TSSOP-28, LFCSP-32 SOIC-8, SC70-5 LFCSP-8, SOIC-8 SOT-23-5, SOIC-8 SOIC-8, MSOP-8 SOT-23-5, SOIC-8 SOIC-8, MSOP-8 SOIC-8, PDIP-8 Table 12. Suitable Analog Devices High Speed Op Amps Part No. AD8065 AD8066 AD8021 AD8392 AD8038 ADA4899 AD8057 AD8058 AD8061 AD8062 AD9631 Supply Voltage (V) 5 to 24 5 to 24 5 to 24 10 to 24 3 to 12 5 to 12 3 to 12 3 to 12 2.7 to 8 2.7 to 8 3 to 6 BW at ACL (MHz) 145 145 490 65 350 600 325 325 320 320 320 Slew Rate (V/s) 180 180 120 900 425 310 1000 850 650 650 1300 Rev. E | Page 19 of 28 AD5544/AD5554 EVALUATION BOARD FOR THE AD5544 The EVAL-AD5544SDZ is used in conjunction with an SDP1Z system demonstration platform board available from Analog Devices, which is purchased separately from the evaluation board. The USB-to-SPI communication to the AD5544 is completed using this Blackfin(R)-based demonstration board. SYSTEM DEMONSTRATION PLATFORM The system demonstration platform (SDP) is a hardware and software evaluation tool for use in conjunction with product evaluation boards. The SDP board is based on the Blackfin ADSP-BF527 processor with USB connectivity to the PC through a USB 2.0 high speed port. For more information about this device, see the system demonstration platform web page. OPERATING THE EVALUATION BOARD 00943-101 The evaluation board requires 12 V and +5 V supplies. The +12 V VDD and -12 V VSS are used to power the output amplifier, and the +5 V is used to power the DAC (DVDD). 00943-100 Figure 28. Evaluation Board Software--AD5544 Quad DAC Figure 27. Evaluation Board Software--Device Selection Window Rev. E | Page 20 of 28 AD5544/AD5554 EVALUATION BOARD SCHEMATICS 00943-102 Figure 29. EVAL-AD5544SDZ Schematic Part A Rev. E | Page 21 of 28 AD5544/AD5554 00943-103 Figure 30. EVAL-AD5544SDZ Schematic Part B Rev. E | Page 22 of 28 AD5544/AD5554 00943-104 Figure 31. EVAL-AD5544SDZ Schematic Part C Rev. E | Page 23 of 28 AD5544/AD5554 00943-105 EVALUATION BOARD LAYOUT 00943-106 Figure 32. Silkscreen Figure 33. Component Side Rev. E | Page 24 of 28 00943-107 AD5544/AD5554 Figure 34. Solder Side Rev. E | Page 25 of 28 AD5544/AD5554 OUTLINE DIMENSIONS 10.50 10.20 9.90 15 28 5.60 5.30 5.00 1 8.20 7.80 7.40 14 0.65 BSC 0.38 0.22 8 4 0 SEATING PLANE 0.95 0.75 0.55 060106-A 0.05 MIN COPLANARITY 0.10 0.25 0.09 1.85 1.75 1.65 2.00 MAX COMPLIANT TO JEDEC STANDARDS MO-150-AH Figure 35. 28-Lead Shrink Small Outline Package [SSOP] (RS-28) Dimensions shown in millimeters 0.30 0.25 0.18 32 25 0.50 BSC 24 0.80 0.75 0.70 SEATING PLANE 0.50 0.40 0.30 8 16 0.05 MAX 0.02 NOM COPLANARITY 0.08 0.20 REF 9 BOTTOM VIEW 0.25 MIN FOR PROPER CONNECTION OF THE EXPOSED PAD, REFER TO THE PIN CONFIGURATION AND FUNCTION DESCRIPTIONS SECTION OF THIS DATA SHEET. COMPLIANT TO JEDEC STANDARDS MO-220-WHHD. Figure 36. 32-Lead Lead Frame Chip Scale Package [LFCSP_WQ] 5 mm x 5 mm Body, Very Very Thin Quad (CP-32-11) Dimensions shown in millimeters Rev. E | Page 26 of 28 3.65 3.50 SQ 3.45 EXPOSED PAD 17 TOP VIEW PIN 1 INDICATOR 1 112408-A PIN 1 INDICATOR 5.10 5.00 SQ 4.90 AD5544/AD5554 ORDERING GUIDE Model 1 AD5544ARS AD5544ARSZ AD5544ARSZ-REEL7 AD5544BRSZ AD5544BRSZ-REEL7 AD5544ACPZ-1-R2 AD5544ACPZ-1-RL7 AD5544BCPZ-R2 AD5544BCPZ-RL7 AD5554BRSZ EVAL-AD5544SDZ 1 RES Bit 16 16 16 16 16 16 16 16 16 14 INL LSB 2 2 2 1 1 4 4 1 1 0.5 DNL LSB 1.5 1.5 1.5 1 1 1 1 1 1 1 Temperature Range -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Z = RoHS Compliant Part. Rev. E | Page 27 of 28 Package Description 28-Lead Shrink Small Outline Package [SSOP] 28-Lead Shrink Small Outline Package [SSOP] 28-Lead Shrink Small Outline Package [SSOP] 28-Lead Shrink Small Outline Package [SSOP] 28-Lead Shrink Small Outline Package [SSOP] 32-Lead LFCSP_WQ 32-Lead LFCSP_WQ 32-Lead LFCSP_WQ 32-Lead LFCSP_WQ 28-Lead Shrink Small Outline Package [SSOP] Evaluation Board Package Option RS-28 RS-28 RS-28 RS-28 RS-28 CP-32-11 CP-32-11 CP-32-11 CP-32-11 RS-28 AD5544/AD5554 NOTES I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors). (c)2000-2011 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00943-0-6/11(E) Rev. E | Page 28 of 28