Preliminary Information - REV_B April 2002
Preliminary Information
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Data Sheet
Features
Description
Applications
Pin Descriptions
Measurement Tables
Functional Description
Features
Description
Applications
Pin Descriptions
Measurement Tables
Functional Description
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Inc, Proprietary and Confidential
Preliminary Information - REV_B Page 2 of 15
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
TABLE OF CONTENTS
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table 1 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Table 2 Pin Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Table 3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 4 Recommended Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 5 AC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Table 6 DC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Modulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Electrical Eye Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Mean Power Control Loop . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Table 7 MPC Loop Bandwidth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Enable Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Current Monitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Slow-Start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Temperature Compensation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Laser Eye Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Laser eye safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
BCC+24L Package Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Disclaimer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
World Wide Sales Offices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Preliminary Information - REV_B Page 3 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
FEATURES
Rise and fall times <150 ps
DC or AC-coupled modulation drive.
Independently Programmable Laser Bias and
Modulation currents.
Bias current to 100 mA and modulation current to
85 mA at VCC = 3.3 V
Automatic Laser Power Control, with programmable
Temperature Compensation and ‘Slow-Start’.
Bias and modulation current monitors
Operates with +3.3 Volt supply
Small BCC+24 package
APPLICATIONS
Gigabit Ethernet
Fibre Channel
2 x Fibre Channel
GBIC
DESCRIPTION
The CX02067 is a highly integrated, programmable laser
driver intended for Datacom applications up to 2.1 Gbps.
Using differential PECL data inputs, the CX02067
supplies the bias and modulation current for driving an
edge-emitting laser. The modulation output can be DC-
coupled to the laser diode, giving a significant power
saving over AC-coupled operation.
The CX02067 includes automatic power control to
maintain a constant average laser output power over
temperature and life. In addition, the modulation current
is temperature compensated to minimize variation in
extinction ratio over temperature.
Output flags indicate laser end of life as well as failure of
the APC circuitry to maintain average output power.
TABLE 1 ORDERING INFORMATION
CONNECTIONS
Part Pin Package
CX02067B24 BCC+24
M02067-TO-EVM TO-Can optical evaluation board
M02067-E-EVM Electrical evaluation board
2
3
4
5
6
78 9 10 11 12 13
14
15
16
17
18
19
24 23 22 21 20
1
ENA
DIS
FAIL
OCA
GND
BIAS
OUT+
OUT-
PD
GND
GND
VCC
GNDA
CMPC
TCSLOPE
TCSTART
MODSET
OCASET
DIN
DIN
VCC
4mm
BIASMON
4mm MODMON
VCC
2067
Fig. 1
Preliminary Information - REV_B Page 4 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
TABLE 2 PIN DESCRIPTION
Note :
Pin 25, the center pad should be connected to ground.
BCC+24
Pin No Name Function
1 ENA Bias and modulation output enable (TTL/CMOS). Logic HIGH for normal operation
2 DIS Bias and modulation output disable (TTL/CMOS). Logic LOW for normal operation
3BIASMON
Bias monitor. Connect a resistor between this pin and VCC to monitor bias current. Connect to VCC if
not used
4MODMON
Modulation monitor. Connect a resistor between this pin and VCC to monitor modulation current.
Connect to VCC if not used
5FAIL
Mean power control failure indicator (TTL/CMOS). Goes LOW when control loop is no longer able to
maintain constant current at PD
6OCA
Over-current alarm (TTL/CMOS). Goes LOW when IBIAS exceeds the preset bias current limit
7 GND Ground
8 BIAS Laser bias current output
9VCC Power supply
10 OUT+ Positive modulation current output. Sinks current when DIN is HIGH
11 OUT- Negative modulation current output. Sinks current when DIN is HIGH
12 GNDAGround to output stage.
13 PD Monitor photodiode input. This input is connected to the monitor photodiode anode for automatic
power control
14 CMPC Mean power control dominant pole capacitor. Connect to VCC via a capacitor
15 GND Ground
16 TCSLOPE Connecting a resistor between this pin and ground sets the temperature coefficient of IMODSET
17 TCSTART
Secondary temperature coefficient of IMOD. A resistor on this pin to ground sets the threshold
temperature at which compensation starts
18 MODSET Modulation current set. Connect a resistor between this pin and ground to set
19 OCASET Over-current alarm set. Connect a resistor between this pin and ground to set
20 VCC Power supply
21 DIN Positive data input (PECL). Self biased
22 DIN Negative data input (PECL). Self biased
23 VCC Power supply
24 GND Ground
Preliminary Information - REV_B Page 5 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
TABLE 3 ABSOLUTE MAXIMUM RATINGS
These are the absolute maximum ratings at or beyond which the IC can be expected to fail or be damaged.
Reliable operation at these extremes for any length of time is not implied.
TABLE 4 RECOMMENDED OPERATING CONDITIONS
TABLE 5 AC CHARACTERISTICS
(VCC = +3.3 V ±10%, TA = -40 °C to +85 °C, unless otherwise noted)
Parameter Rating Units
Power supply (VCC-GND) -0.5 to +6.0 V
Maximum laser bias current 120 mA
Maximum laser modulation current (through OUT+, OUT-) 100 mA
Storage temperature -65 to +150 °C
Junction temperature (die) -40 to +120 °C
Parameter Rating Units
Power supply (VCC-GND) 3.3 ± 10% V
Operating ambient temperature -40 to +85 °C
Parameter Conditions Min. Typ. Max. Units
Differential input voltage = 2 x (DIN+HIGH-DIN+LOW)300 - 1860 mV
Modulation current range 2.5 - 85 mA
Modulation current with output disabled DIS = HIGH - - 300 µA
Programmable range for modulation
current temperature coefficient Adjustable 500 - 104ppm/°C
Programmable temperature at which
modulation current TC compensation
enables
Programmed by choice of RTCSLOPE 20 - 60 °C
Modulation output rise/fall times 20% to 80% into 25 Ω, with matching
network - - 150 ps
Overshoot of modulation output current Into 25 Ω load, with matching network -5 - +5 %
Modulation output Pulse width distortion Measured using alternating 1-0 pattern - - 50 ps
Modulation output deterministic jitter Peak-to-peak. Measured into 25 Ω load
using 27-1 PRBS at 2.1 Gbps - - 50 ps
Preliminary Information - REV_B Page 6 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
TABLE 6 DC CHARACTERISTICS
(VCC = +3.3 V ±10%, TA = -40 °C to +85 °C, unless otherwise noted)
Note:
(1) Condition when pin 19 OCASET is connected to ground.
(2) Time for optical power to reach 90% of its mean level following negation of Tx_Disable.
(3) Time for optical power to reach 10% of its mean level following assertion of Tx_Disable.
Parameter Conditions Min. Typ. Max. Units
Supply current Excluding IBIAS and IMOD but with
IBIAS and IMOD set to maximum -52 64 mA
Bias current adjust range Limited by IREF across
temperature range 4 - 100 mA
Bias current with output disabled Tx-Dis = HIGH - - 300 µA
Maximum bias current limit TA = +85 °C (adjustable) 100(1) --mA
Monitor diode reverse bias voltage 2 - - V
Monitor diode current adjustment
range 40 - 1000 µA
TTL/CMOS input HIGH voltage
(enable/disable) 2.0 - - V
TTL/CMOS input LOW voltage
(enable/disable) -- 0.8 V
CMOS output HIGH voltage
(Fail,OCA) 2.4 - - V
CMOS output LOW voltage
(Fail,OCA) -- 0.4 V
Differential input impedance Data and clock inputs 2.5 - - kΩ
Common-mode input voltage‘ VCC -1.38 -VCC - VIN(Diff)
4 V
Self-biased common mode input
voltage Data and clock inputs VCC -1.38 -VCC -0.47 V
Ratio of bias monitoring current, and
bias current 55
Ratio of modulation monitoring
current, and modulation current 55
Tx_Disable negate time (2) CMPC = 3.8 nF .5 1 ms
Tx_Disable assert time (3) 1µs
Preliminary Information - REV_B Page 7 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
FUNCTIONAL DIAGRAM
FUNCTIONAL DESCRIPTION
Overview
The CX02067 laser driver consists of a high-speed
modulation driver and a laser bias generator with mean
power control (MPC). It is optimized for high speed, low
power operation at 3.3 V supply. Fig. 2 demonstrates the
functionallity of the CX02067.
Modulator
The modulator output stage is designed to drive up to
85 mA in either AC-coupled or DC-coupled mode.
DC-coupled performance depends on the laser used.
The CX02067 modulation output is optimized for driving a
25 Ω load; the minimum required voltage at OUT+ and
OUT- is 0.6 V. To interface with the laser diode, a
matching resistor (RD) is required for impedance
matching. An RC shunt network is necessary to
compensate for the laser diode parasitic inductance,
thereby improving the optical eye. Typical values are
RSHUNT = 51 Ω, CSHUNT = 3.3 pF
Any capacitive loading at the cathode of a laser diode will
degrade the optical output performance. An inductor is
used to isolate the BIAS pin from the laser cathode.
Fig. 3 shows the typical IMOD vs RMODSET characteristic.
X100
X60
Failure
Detect
DIS
ENA
55
55
FAIL
X1
OCA
DATA
BIASMON
MODMON
IBIAS
IMOD
OUT-
OUT+
VCC
IBIAS
RMODSET
RTCSLOPE
RTCSTART
RMPCSET
VCC
CMPC
VREF
PD
ROCA
OCASET
RD
GNDA
RSHUNT
CSHUNT
VCC
Fig. 2
0
20
40
60
80
100
120
0 4000 8000 12000 16000 20000 24000 28000 32000
R
MODSET (Ω)
IMOD (mA)
Fig. 3
Preliminary Information - REV_B Page 8 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
ELECTRICAL EYE DIAGRAM
Fibre Channel 1.0625 Gbps
30 mApp Modulation Current
Gigabit Ethernet 1.25 Gbps
30 mApp Modulation Current
Fig. 4
2 x Fibre Channel 2.125 Gbps
30 mApp Modulation Current
Preliminary Information - REV_B Page 9 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
FUNCTIONAL DESCRIPTION
Mean Power Control Loop
The CX02067 employs a Mean Power Control (MPC)
loop to maintain a constant optical output power from the
laser across temperature, time and power supply
variations. Laser diodes used for communication
purposes come with integrated photo-diodes to monitor
the output power and provide the feedback for the MPC
loop. The MPC loop (or its integrated safety features)
cannot be used without this feedback.
The MPC loop adjusts the laser bias current so that the
monitor current from the photo-diode is matched to a
reference current set by a single external resistor,
RMPCSET. The time constant of the MPC loop is
determined by CMPC.
TABLE 7 MPC LOOP BANDWIDTH
(at 6 dB cut off frequency) vs CMPC (for nominal process)
Fig. 5 shows the bias current vs RMPCSET over the full
operating temperature range
There are two safety features integrated into the MPC
loop; an Over-Current Alarm and an MPC loop failure
alarm.
The Over-Current Alarm (OCA) circuit limits the
maximum bias current generated by the CX02067. The
bias current limit is set by an external resistor to ground,
ROCA. When this limit is exceeded the OCA pin is
asserted LOW. Fig. 6 shows the maximum bias current
limit vs ROCA.
The MPC loop FAILure alarm (FAIL) is generated by the
CX02067 when the MPC loop can no longer maintain the
constant current set by RMPCSET. When the MPC loop
failure alarm is triggered the FAIL pin is asserted LOW.
Enable Control
The CX02067 incorporates a dual polarity laser enable
function with both enable (ENA) and disable (DIS) inputs.
Under normal operating conditions the ENA will be HIGH
while DIS is LOW. Should ENA go LOW (or DIS go HIGH)
both the bias and modulation currents will be disabled.
Wire OR-ing the OCA and FAIL pins externally and
connecting them to the ENA pin will automatically disable
the bias and modulation currents when a failure occurs.
Current Monitors
The CX02067 features bias and modulation current
monitor outputs. The BIASMON output sinks a current
equal to nominally 1/55 of the laser bias current (IBIAS).
The MODMON output sinks a current equal to nominally
1/55 of the laser modulation current (IMOD). BIASMON and
MODMON should be connected through a pull-up resistor
to VCC. Choose a pull-up resistor value that ensures a
voltage at BIASMON greater than VCC - 1.6 V and a
voltage at MODMON greater than VCC - 1.0 V. These pins
should be tied to VCC if not used.
CMPC 6 dB cutoff frequency
0 17 MHz
1 nF 100 kHz
10 nF 10 kHz
100 nF 1 kHz
0
20
40
60
80
100
120
0 5000 10000 15000 20000 25000 30000 35000
RMPCSET Ω
Bias current
(mA)
-40 025 50 85
Symbols shown indicate °C
Fig. 5
0
10
20
30
40
50
60
70
80
90
100
0 10000 20000 30000 40000
ROCA (Ω)
IOCA (mA)
Fig. 6
Preliminary Information - REV_B Page 10 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
FUNCTIONAL DESCRIPTION
Slow-Start
For laser safety and reliability, the CX02067 incorporates
a slow-start circuit that provides a delay of approximately
200 ns before enabling the laser diode.
Temperature Compensation
The CX02067 features built in temperature compensation
of the modulation current is set using two external
resistors, TCSLOPE and TCSTART see Fig. 7.
Current pulled from TCSLOPE adjusts the slope of the
temperature compensation whereas current pulled from
TCSTART sets the threshold temperature for the
coefficient.
Fig. 8 to 10 shows IMOD temperature compensation using
a combination of resistor values for RTCSLOPE and
RTCSTART.
TCSLOPE
TCSTART
80mA
0mA
+80°C-40°C
1∆
2∆
RMPCSET
Fig. 7
0.04
0.042
0.044
0.046
0.048
0.05
0.052
0.054
0.056
0.058
0.06
-40 -20 0 20 40 60 80 100
Temperature (°C)
IMOD (A)
5000 10000 20000 32000
RTCSLOPE - Figures shown are in Ω
RTCSTART = 0 Ω, VCC = 3.3V
Fig. 8
0.04
0.045
0.05
0.055
0.06
0.065
0.07
0.075
0.08
0.085
-40-20 0 20406080100
Temperature (°C)
IMOD (A)
5000 10000 20000 32000
RTCSLOPE - Figures shown are in Ω
RTCSTART = 250 Ω, VCC = 3.3V
Fig. 9
0.04
0.05
0.06
0.07
0.08
0.09
0.1
-40-20 0 20406080100
Temperature (°C)
Imod (A)
5000 10000 20000 32000
RTCSLOPE - Figures shown are in Ω
RTCSTART = 400 Ω, VCC = 3.3V
Fig. 10
Preliminary Information - REV_B Page 11 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
LASER EYE SAFETY
Laser eye safety
All lasers for commercial and industrial use, including
lasers for optical communications are classified for eye
safety considerations in IEC 60825-1, CDRH and other
national standards.
IMPORTANT NOTE:
The CX02067 alone does NOT ensure that any
application within which it is used will be fully
compliant with the relevant eye-safety requirements.
It remains the sole responsibility of the user of this
component to ensure that the application within
which the CX02067 is used meets all eye-safety
requirements.
Preliminary Information - REV_B Page 12 of 14
CX02067
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
BCC+24L PACKAGE OUTLINE
TOP VIEW
BOTTOM VIEW
0.15
XM ZY0.08
0.05 Z
0.20 Z
Z
Y
X
0.45 ± 0.03
0.45 ± 0.03
XM ZY0.08
DETAIL " A"
0.40 ± 0.03
0.30 ± 0.03
XM ZY0.08
XM ZY0.08
DETAIL " B" (20X)
DET AIL " C" (3 X)
0.45 ± 0 .03
0.45 ± 0.03
XM ZY0.08
MZ0.08 XY
4.00± 0.10
4.00± 0.10
0.67± 0.025 0.075± 0.025
0.80 M AX
"B"
0.50± 0.100.50 TYP.
3.15
3.20 "C"
3.20
0.50± 0.100.50 TYP.
3.15
2.20
2.20
C.L(PKG.)
C.L(PKG.)
C0.2
"A"(PI N 1 CORNER)
(P I N 1 C OR NE R
)
Fig. 12
Note : All dimensions are in mm.
CX02067
Preliminary Information - REV_B Page 13 of 14
3.3 Volt Laser Driver IC for GbE and Fibre Channel to 2.1 Gbps
Preliminary Information
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
DISCLAIMER
© 2001 Mindspeed Technologies™, as a wholly owned subsidiary and the Internet infrastructure business of Conexant
Systems, All Rights are Reserved.
Information in this document is provided in connection with Mindspeed Technologies. "Mindspeed" products. These
materials are provided by Mindspeed as a service to its customers and may be used for informational purposes only.
Mindspeed assumes no responsibility for errors or omissions in these materials. Mindspeed may make changes to
specifications and product descriptions at any time, without notice. Mindspeed makes no commitment to update the
information contained herein. Mindspeed shall have no responsibility whatsoever for conflicts or incompatibilities arising
from future changes to its specifications and product descriptions.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document.
Except as provided in Mindspeed Terms and Conditions of Sale for such products, Mindspeed assumes no liability
whatsoever.
THESE MATERIALS ARE PROVIDED "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED,
RELATING TO SALE AND/OR USE OF CONEXANT PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING
TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT,
COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. Mindspeed further does not warrant the accuracy or
completeness of the information, text, graphics or other items contained within these materials. Mindspeed shall not be
liable for any special, indirect, incidental, or consequential damages, including without limitation, lost revenues or lost
profits, which may result from the use of these materials.
Mindspeed products are not intended for use in medical, life saving or life sustaining applications. Mindspeed customers
using or selling Mindspeed products for use in such applications do so at their own risk and agree to fully indemnify
Mindspeed for any damages resulting from such improper use or sale.
The following are trademarks of Mindspeed Technologies,. the symbol M1, Mindspeed™, and "Build It First™" Product
names or services listed in this publication are for identification purposes only, and may be trademarks of third parties.
Third-party brands and names are the property of their respective owners.
Reader Response: Mindspeed Technologies, strives to produce quality documentation and welcomes your feedback.
Please send comments and suggestions to mailto:tech.pubs@mindspeed.com. For technical questions, or to talk to a field
applications engineer contact your local Mindspeed™ sales office listed below. For literature send email request to
literature@mindspeed.com.
Preliminary Information - REV_B Page 14 of 14
Americas
US Northwest/Northwest Canada
Santa Clara
Phone: (408) 423-4500
Fax: (408) 249-7113
US North Central
Illinois/Colorado
Phone: (630) 799-9300
Fax: (630) 799-9325
US South Central
Texas
Phone: (972) 735-1540
Fax: (972) 407-0639
Eastern Canada
Ontario
Phone: (613) 271-2358
Fax: (613) 271-2359
US Northeast
Massachusetts
Phone: (978) 244-7680
Fax: (978) 244-6868
US Southeast
North Carolina
Phone: (919) 858-9110
Fax: (919) 858-8669
US Florida / South America
Florida
Phone: (727) 799-8406
Fax: (727) 799-8306
US Mid-Atlantic
Pennsylvania
Phone: (215) 245-2470
Fax: (215) 245-2480
Asia
P.R. China - Central and North
Australia and New Zealand
Phone: (86-21) 6350-5702
Fax: (6-21) 6361-2516
P.R. China - South/Hong Kong
Phone: 86-755-2300-420
Fax: 86-755-2300-421
Asia South - Taiwan
India, Indonesia, Malaysia, Pakistan,
Philippines, Singapore, Taiwan, Thailand
and Vietnam
Phone: (886-2) 8789-8366
Fax: (886-2) 8789-8367
Korea
Phone: 82-2-528-4301
Fax: 82-2-528-4305
Japan
Phone: (81-3) 5380 1731
Fax: (81-3) 5350-5431
Europe
Europe Central - Germany
Austria, Germany, Hungary, Poland,
Romania, Russia and Switzerland
Phone: (49) 89-82005-151
Fax: (49) 89-82005-150
Europe Mediterranean - Israel
Greece, Israel, Italy, Spain and Portugal
Phone: (972) 9961-5100
Fax: (972) 9957 5166
Europe North - UK
Belgium, Denmark, Finland, France, Ireland
Luxembourg, Norway, Sweden,
The Netherlands and United Kingdom
Phone: 44 (0) 118 920 9500
Fax: 44 (0) 118 920 9595
Headquarters
Newport Beach
Mindspeed Technologies
4000 MacArthur Boulevard, East Tower
Newport Beach, CA 92660
Phone: (949) 579-3000
Fax: (949) 579-3020
www.mindspeed.com
World Wide Sales Offices
Information provided in this Data Sheet is PRELIMINARY and is subject to change without notice.
Mindspeed™ Technologies, Proprietary and Confidential
