PWM-QR IC
TDA4601
Control IC for Switched-Mode
Power Supplies
Never stop thinking.
Power Management & Supply
Datasheet, V2.0, 1 Jun 1994
Edition 1994-06-01
Published by Infineon Technologies AG,
St.-Martin-Strasse 53,
D-81541 München
© Infineon Technologies AG 1999.
All Rights Reserved.
Attention please!
The information herein is given to describe certain components and shall not be considered as warranted char-
acteristics.
Terms of delivery and rights to technical change reserved.
We hereby discla im any and all w arranties, including bu t not limited to warranties of non -infringement, regarding
circuits, descriptions and charts stated herein.
Infineon Technologies is an approved CECC manufacturer.
Information
Fo r further information on technology, delivery terms and conditions and prices please contact your nearest I nfin-
eon Technologies Office in Germany or our Infineon Technologies Representativ es worldwide (see address list).
Warnings
Due to technical requirements componen ts may contain dangerous substances. For information on the types in
question please contact your nearest Infineon Technologies Office.
Infineon Technologies Components may only be used in life-support devi ces or syste ms with the express written
approv al of Infineon Technolog ies, if a f ailure of such componen ts can reasonably be e xpected to cause the f ailure
of that life-support device or system, or to affect the safety or effectiveness of that device or system. Life support
devices or systems are intended to be implanted in the human body, or to support and/or maintain and sustain
and/or protect human life. If they fail, it is reasonable to assume that the health of the user or other persons may
be endangered.
For questions on technology, delivery and prices please contact t he Infineon Technolo gies Offices in Germany or
the Infineon Technologies Companies and Representatives worldwide: see our webpage at http://
www.infineon.com
TDA4601
Revision History: 1994-06-01 Datasheet
Previous Version:
Page Subjects (major changes since last revision)
The integrated circuit TDA 4601/D is designed for driving, controlling and protecting the switching
transistor in self-oscillating flyback converter power supplies as well as for protecting the overall
power supply unit. In case of disturbance, the rise of the secondary voltage is prevented. In addition
to the ICs application range including TV-receivers video tape recorders, hifi devices and active
loudspeakers, it can also be used in power supply units for professional applications due to its wide
control range and high voltage stability during increased load changes.
Type Ordering Code Package
TDA 4601 Q67000-A2379 P-SIP-9-1
Control ICs for Switched-Mode Power Supplies
Bipolar IC
TDA 4601
P-SIP-9-1
Features
Direct control of the switching transistor
Low start-up current
Reversing linear overload characteristic
Base current drive proportional to collector current
Protective circuit in case of disturbance
Version 2.0 3 1 Jun 1994
Version 2.0 4 1 Jun 1994
TDA 4601
Block Diagram
Pin Definitions and Functions
Pin No. Function
1VREF output
2 Zero passage identification
3 Input control amplifier, overload amplifier
4 Collector current simulation
5 Connection for additional protective circuit
6 Ground (rigidly connected to substrate mounting plate)
7 DC-output for charging coupling capacitor
8 Pulse output - driving of switching transistor
9 Supply voltage
Version 2.0 5 1 Jun 1994
TDA 4601
Circuit Description
The TDA 4601 is designed for driving, controlling and protecting the switching transistor in flyback
converter power supplies during start-up, normal and overload operations as well as during
disturbed operation. In case of disturbance the drive of the switching transistor is inhibited and a
secondary voltage rise is prevented.
Start-Up
The start-up procedures (on-mode) include three consecutive operating phases as follows:
1. Build-Up of Internal Reference Voltage
The internal reference voltage supplies the voltage regulator and effects charging of the coupling
electrolytic capacitor connected to the switching transistor. Current consumption will remain at
I9< 3.2 mA with a supply voltage up to V9 approx. 12 V.
2. Enabling of Internal Voltage - Reference Voltage V1 = 4 V
Simultaneously with V9 reaching approx. 12 V, an internal voltage becomes available, providing
all component elements, with the exception of the control logic, with a thermally stable and
overload-resistant current supply.
3. Enabling of Control Logic
In conjunction with the generation of the reference voltage, the current supply for the control logic
is activated by means of an additional stabilization circuit. The integrated circuit is then ready for
operation.
The start-up phase above described are necessary for ensuring the charging of the coupling
electrolytic capacitor, which in turn supplies the switching transistor. Only then is it possible to
ensure that the transistor switches accurately.
Normal Operating Mode / Control Operating Mode
At the input of pin 2 the zero passages of the frequency provided by the feedback coil are registered
and forwarded to the control logic. Pin 3 (control input, overload and standby identification) receives
the rectified amplitude fluctuations of the feedback coil. The control amplifier operates with an input
voltage of approx. 2 V and a current of approx. 1.4 mA. Depending on the internal voltage reference,
the overload identification limits inconjunction with collector current simulator pin 4 the operating
range of the control amplifier. The collector current is simulated by an external RC-combination
present at pin 4 and internally set threshold voltages. The largest possible collector current
applicable to the switching transistor (point of return) increases in proportion to the increased
capacitance (10 nF). Thus the required operating range of the control amplifier is established. The
range of control lies between a DC-voltage clamped at 2 V and a sawtooth - shaped rising AC-
voltage, which can vary up to a max. amplitude of 4 V (reference voltage). During secondary load
reduction to approx. 20 W, the switching frequency is increased (approx. 50 kHz) at an almost
constant pulse duty factor (1:3). During additional secondary load decreases to approx. 1 W, the
switching frequency increases to approx. 70 kHz and pulse duty factor to approx. 1:11. At the same
time collector peak current is reduced to < 1 A.
Version 2.0 6 1 Jun 1994
TDA 4601
The output levels of the control amplifier as well as those of the overload identification and collector
current simulator are compared in the trigger and forwarded to the control logic. Via pin 5 it is
possible to externally inhibit the operations of the IC. The output at pin
pin 8 will be inhibited when voltages of – 0.1 are present at pin 5.
Flipflops for controlling the base current amplifier and the base current shut-down are set in the
control logic depending on the start-up circuit, the zero passage identification as well as on the
enabling by the trigger. The base current amplifier forwards the sawtoothspahed V4 voltage to the
output of pin 8. A current feedback with an external resistor (R = 0.68 ) is present between pin 8
and pin 7. The applied value of the resistor determines the max. amplitude of the base driving
current for the switching transistor.
Protective Operating Mode
The base current shut-down activated by the control logic clamps the output of pin 7 to 1.6 V. As a
result, the drive of the switching transistor is inhibited. This protective measure is enabled if the
supply voltage at pin 9 reaches a value 6.7 V or if voltages of
– 0.1 are present at pin 5.
In case of short-circuits occurring in the secondary windings of the switched-mode power supply,
the integrated circuit continuously monitors the fault conditions. During secondary, completely load-
free operation only a small pulse duty factor is set. As a result the total power consumption of the
power supply is held at N= 6 ... 10 W during both operating modes. After the output has been
inhibited for a voltage supply of 6.7 V, the reference voltage (4 V) is switched off if the voltage
supply is further reduced by V9= 0.6 V.
Protective Operating Mode at Pin 5 in Case of Disturbance
The protection against disturbances such as primary undervoltages and/or secondary over-
voltages (e.g. by changes in the component parameters for the switched-mode power supply) is
realized as follows:
Protective Operating Mode with Continuous Fault Condition Monitoring
In case of disturbance the output pulses at pin 8 are inhibited by falling below the protective
threshold V5, with a typical value of V1/2. As a result current consumption is reduced (I914 mA
at V9=10V).
With a corresponding high-impedance start-up resistor *), supply voltage V9 will fall below the
minimum shut-down threshold (5.7 V) for reference voltage V1.V1 will be switched off and current
consumption is further reduced to I93.2 mA at V910 V.
Because of these reductions in current consumption, the supply voltage can rise again to reach the
switch-on threshold of V912.3 V. The protective threshold at pin 5 is released and the power
supply is again ready for operation.
VREF
2
------------
VREF
2
------------
Version 2.0 7 1 Jun 1994
TDA 4601
In case of continuing problems of disturbance (V5V1/2 0.1 V) the switch-on mode is interrupted
by the periodic protective operating mode described above, i.e. pin 8 is inhibited and V9 is falling,
etc.
Switch-On in the Wide Range Power Supply (90 Vac to 270 Vac)
(application circuit 2)
Self-oscillating flyback-converters designed as wide range power supplies require a power source
independent of the rectified line voltage for TDA 4601. Therefore the winding polarity of winding
11/13 corresponds to the secondary side of the flyback converter transformer. Start-up is not as
smooth as with an immediately available supply voltage, because TDA 4601 has to be supplied by
the start-up circuit until the entire secondary load has been charged. This leads to long switch-on
times, especially if low line voltages are applied.
However, the switch-on time can be shortened by applying the special start-up circuit (dotted line).
The uncontrolled phase of feedback control winding 15/9 is used for activating purposes.
Subsequent to activation, the transistor T1 begins to block when winding 11/13 generates the
current supply for TDA 4601. Therefore, the control circuit cannot be influenced during operation.
Version 2.0 8 1 Jun 1994
TDA 4601
Absolute Maximum Ratings
Parameter Symbol Limit Values Unit
min. max.
Supply voltage V9020V
Voltages
Reference output V106V
Zero passage identification V2– 0.6 0.6 V
Control amplifier V303V
Collector current simulation V408V
Blocking input V508V
Base current cut-off point V70V9V
Base current amplifier output V80V9V
Currents
Zero passage identification Il i2 –5 5 mA
Control amplifier Il 3 – 3 3 mA
Collector current simulation Il 4 05mA
Blocking input Il 5 05mA
Base current cut-off point IQ 7 – 1 1.5 A
Base current amplifier output IQ 8 – 1.5 0 A
Junction temperature Tj125 ˚C
Storage temperature range Tstg – 40 125 ˚C
Thermal resistances:
system-air TDA 4601
system-case TDA 4601 Rth SA
Rth SC
70
15 K/W
K/W
system-air 1) TDA 4601-D
system-case 2) TDA 4601-D Rth SA
Rth SA1
60
44 K/W
K/W
Version 2.0 9 1 Jun 1994
TDA 4601
1) Case soldered on PC-board without cooling surface
2) Case soldered on PC-board with copper-clad 35 µm layer, cooling surface 25 cm2
3) Rth SA1 = 44 K/W and PV = 1 W
Operating Range
Supply voltage V97.8 18 V
Case temperature TDA 4601 TC085˚C
Ambient temperature range 3) TDA 4601-D TA070˚C
Absolute Maximum Ratings (cont’d)
Parameter Symbol Limit Values Unit
min. max.
Version 2.0 10 1 Jun 1994
TDA 4601
*) DC-component only
Characteristics
TA = 25 ˚C
according to measurement circuit 1 and diagram
Parameter Symbol Limit Values Unit
min. typ. max.
Start Operation
Current consumption (V1 not yet
switched on)
V9 = 2 V
V9 = 5 V
V9 = 10 V
I9
I9
I9
1.5
2.4
0.5
2.0
3.2
mA
mA
mA
Switching point for V1V911.0 11.8 12.3 V
Normal Operation
V9 = 10 V; Vcont = – 10 V; Vclock = ± 0.5 V; f = 20 kHz
duty cycle 1:2 after switch-on
Current consumtion
Vcont = – 10 V
Vcont = 0 V I9
I9
110
50 135
75 160
100 mA
mA
Reference voltage
I1 < 0.1 mA
I1 < 5 mA V1
V1
4.0
4.0 4.2
4.2 4.5
4.5 V
V
Temperature coeffiecient of
reference voltage TC1–10
– 3 1/K
Control voltage Vcont = 0 V V32.3 2.6 2.9 V
Collector current simulation voltage
Vcont = 0 V
Vcont = 0 V/– 10 V V4*)
V4*)1.8
0.3 2.2
0.4 2.5
0.5 V
V
Clamping voltage V56.0 7.0 8.0 V
Output voltages
Vcont = 0 V
Vcont = 0 V
Vcont = 0 V/– 10 V
VQ7 *)
VQ8 *)
VQ8
2.7
2.7
1.6
3.3
3.4
2.0
4.0
4.0
2.4
V
V
V
Feedback voltage V2*)0.2 V
Version 2.0 11 1 Jun 1994
TDA 4601
The cooling conditions have to be optimized with regard to maximum ratings
(TA;Tj;Rth JC ;Rth SA).
Protective Operation
V9 = 10 V; Vcont = – 10 V; Vclock =  0.5 V; f = 20 kHz;
duty cycle 1:2
Parameter Symbol Limit Values Unit
min. typ. max.
Current consumption
V5 < 1.9 V I914 22 28 mA
Switch-off voltage
V5 < 1.9 V VQ 7 1.3 1.5 1.8 V
Switch-off voltage
V5 < 1.9 V V41.8 2.1 2.5 V
Blocking input
Blocking voltage
Vcont = 0 V V5V
Supply voltage blocked for V8
Vcont = 0 V V46.7 7.4 7.8 V
V1 off (with further reduction of V9)V90.3 0.6 1.0 V
Characteristics
TA = 25 ˚C; according to measurement circuit 2
Parameter Symbol Limit Values Unit
min. typ. max.
Switching time (secondary voltage) tON 350 450 ms
Voltage variation S3 = closed
N3 = 20 W V2 sec 100 500 mV
Voltage variation S2 = closed
N3 = 15 W V2 sec 500 1000 mV
Standby operation S1 = open
secondary useful load = 3 W V2 sec
f70 20
75 30
V
kHz
V1
2
------ 0.1V1
2
------
Version 2.0 12 1 Jun 1994
TDA 4601
Circuit Diagram
Version 2.0 13 1 Jun 1994
TDA 4601
Test and Measurement Circuit 1
Test Diagram: Overload Operation
Version 2.0 14 1 Jun 1994
TDA 4601
Application Circuit 2
Wide range from 80 to 270 Vac
Version 2.0 15 1 Jun 1994
TDA 4601
Notes on Application Circuit 2
Wide Range SMPS
Filtering of the rectified AC-voltage has been increased up to 470µF to ensure a constant and hum-
free supply at Vline = 80 Vac. The stabilized phase is tapped for supplying the IC. In order to ensure
good start-up conditions for the SMPS in the low voltage range, the non-stabilized phase of winding
13/15 is used as a starting aid (BD 139), which is turned off after start-up by means of Z-diode C12.
In comparison to the 220 Vac standard circuit, however, the collector-emitter circuit had to be
altered to improve the switching behavior of BU 208 for the entire voltage range (80 to 270 Vac).
Diode BY 231 is necessary to prevent inverse operation of BU 208 and may be integrated for
switching times with a secondary power < 75 W (BU 208 D).
Compared to the IC TDA 4600-2, the TDA 4601 has been improved in turn-off during under-voltage
at pin 5. The TDA 4601 is additionally provided with a differential amplifier input at pin 5, enabling
precise turn-off at the output of pin 8 accompanied by hysteresis. For wide range SMPS, TDA 4601
is recommendable instead of TDA 4600-2. If a constant quality standard equal to that of the
standard circuit is to be maintained, wide range SMPS (80 to 270 Vac) with secondary power of
120 W can only be implemented at the expense of time.
Version 2.0 16 1 Jun 1994
TDA 4601
Supplements to Application Circuit 2
Efficiency versus Output Power
Efficiency versus Output Power
Version 2.0 17 1 Jun 1994
TDA 4601
Supplements to Application Circuit 2
Load Characteristics V2sec = f (I2sec)
Output Voltage V2sec (line change)
Version 2.0 18 1 Jun 1994
TDA 4601
Further Applications
Application Circuit 3
Version 2.0 19 1 Jun 1994
TDA 4601
Notes on Application Circuit 3
Fully Insulated, Clamp-contacted PTC-Thermistor Suitable for SMPS-Applications at
Increased Start-Up Currents
The newly developed PTC-thermistor Q63100-P2462-J29 is designed for applications in SMPS as
well as in various other electronic circuits, which, for example, receive the supply voltage directly
from the rectified line voltage and require an increased current during turn-on. Used in the flyback
converter power supply of TV-sets, an application proved millions of times over, the new PTC-
thermistor in the auxiliary circuit branch has resulted in a power saving of no less than 2 W. This
increase in efficiency has a highly favorable effect on the standby operation of TV-sets.
The required turn-on current needs only 6 to 8 s until the operating temperature of the PTC-
thermistor is reached. Low thermal capacitance of the PTC-thermistor allows the circuit to be
operated again after no more than 2 s. Another positive feature is the improved short-circuit
strength. The clamp contacts permit more or less unlimited switching operations and thus
guarantee high reliability. A flame-retardant plastic package and small dimensions are additional
advantages of this newly developed PTC-thermistor.
Technical Data
Parameter Symbol Limit Values Unit
Breakdown voltage at TA = 60 ˚C VBD rms 350 V
Resistance at TA = 25 ˚C R25 5k
Resistance tolerance R25 25 %
Trip current (typ.) IK20 mA
Residual current at VA max IR2mA
Max. application voltage Vop max rms 265 V
Reference temperature (typ.) TREF 190 ˚C
Temperature coefficient (typ.) TC26 %/K
Max. operating current Imax 0.1 A
Storage temperature range Tstg – 25 to 125 ˚C
Version 2.0 20 1 Jun 1994
TDA 4601
Application Circuit 4
Version 2.0 21 1 Jun 1994
TDA 4601
Notes on Application Circuit 4
Improved Load Control and Short-Circuit Characteristics
Turn-on is the same as for circuit 3.
To make the price more attractive, switching transistor BU 508 A was selected.
To ensure optimum standby conditions, the capacitance between pins 2 and 3 was increased to
100 pF.
Z- diode C6.2 transfers control voltage Vcont directly to pin 3 resulting in improved load control.
Design and coupling conditions of various flyback transformers were sometimes a reason for
overshoot spectra, which, despite the RC-attenuating element 33 x 22 nF and the 10-k resistor,
even penetrated across the feedback winding 9/15 to the zero passage indicator input (pin 2) and
activated double and multiple pulses in the IC. Double and multiple pulses, however, lead to
magnetic saturation in the flyback transformer and thus increase the risk of damaging the switched-
mode power supply.
The larger the quantities of power to be passed, the more easily overshoots are generated. This
can be observed around the point of return. The switched-mode power supply, however, reduces
its own power to a minimum in all cases of overload or short-circuit. A series resonant circuit, whose
resonance corresponds to the transformer’s selfoscillation, was created by combination of the
4.7-µH inductance and the 22-nF capacitance. This resonant circuit short-circuits overshoots via a
33- resistor.
f1
2πLC
----------------- 500 kHz=


Version 2.0 22 1 Jun 1994
TDA 4601
Application Circuit 5
Version 2.0 23 1 Jun 1994
TDA 4601
Notes on Application Circuit 5
Highly Stable Secondary Side
Power supplies for commercial purposes require highly constant low voltages and high currents
which, on the basis of the flyback converter principle, can be realized only under certain conditions,
but, on the other hand, are implemented for economical reasons. An electrically isolated flyback
converter with a highly stable secondary side must receive the control information from this
secondary side. There are only two possibilities for meeting this requirement: either through a
transformer which is magnetically isolated from the flyback converter or by means of an
optocoupler. The development of CNY 17 has enabled the manufacture of a component suitable for
electrical isolation and characterized by high reliability and long-term stability.
The IC TDA 4601-D is the sucessor of the TDA 4600-D. It is compatible with its predecessor in all
operational functions and in the control of a self-oscillating flyback converter. Pin 3 is the input for
the control information, where the latter is compared with the reference voltage prevailing at pin 1
and the control from the optocoupler and subsequently transformed into a frequency/pulse width
control.
The previous feedback and control information winding is not necessary. The feedback information
(zero passage) is obtained from winding 3/4 - supply winding. The time constant chain 330 /3.3 nF
and 330 /2.2 nF was implemented in series with 150 µH to prevent interference at pin 2. The LC-
element forms a series resonant circuit for overshoots of the flyback converter and short-circuits
them.
Version 2.0 24 1 Jun 1994
TDA 4601
Application Circuit 6
Version 2.0 25 1 Jun 1994
TDA 4601
Notes on Application Circuit 6
Wide Range Plug SMPS up to 30 W
Due to their volume and weight, plug SMPS have so far been limited to a restricted primary voltage
and a secondary power of no more than 6 W.
The line-isolated wide range flyback converter presented here has a variable frequency and is
capable of producing a secondary power of 30 W. It is characterized by a compact design with an
approx. weight of 400 g. The entire line voltage range of 90 to 260 Vac is stabilized to ±1.5 % on
the secondary side. Load fluctuations between 0.1 and 2 A are regulated to within 5 %. The output
(secondary side) is overload, short-circuit, and openloop proof.
Version 2.0 26 1 Jun 1994
TDA 4601
Application Circuit 7
Version 2.0 27 1 Jun 1994
TDA 4601
Notes on Application Circuit 7
Wide Range SMPS with Reducing Peak Collector Current ICBU208
for Rising Line Voltage
(variable point of return)
Wide range SMPS have to be dimensioned at line voltages of 90 to 260 Vac. The difference
between the maximum collector current IC BU 208 max and the largest possible limit current
IC BU 208 limit which causes magnetic saturation of the flyback transformer and flows through the
primary inductance winding 5/7 is to be determined at Vacmin (IC BU 208 limit 1.2 x IC BU 208 max).
Then, the transmissible power of the flyback transformer and its value at Vacmax is to be determined.
In the standard circuit the collector current IC BU 208 max is almost constant at the point of return
independent of the line voltage. The transmissible power on the secondary side, however,
increases at the point of return in proportion to the rising rectified line voltage applied (figures 1 and
2).
In the wide range SMPS a line voltage ratio of 270/90 = 3/1 is obtained, causing doubling of the
transmissible power on the secondary side, i.e. in the wide range SMPS a far too large flyback
transformer had to be implemented.
The point of return protecting the SMPS against overloads or short circuits, is derived from the time
constant at pin 4 t4
= 270 k x 4.7 nF. Thus, the largest possible pulse width is determined.
With the introduction of the 33-k resistor this time constant is reduced as a function of the control
voltage applied to winding 13/15, rectified by diode BY 360 and filtered by the 1-µF capacitance,
which means that the pulse time becomes shorter. By means of the Z-diode
C
18 the line voltage
level can be defined at which the influence of the time constant correction becomes noticeable. The
change in the rectified voltage of winding 13/15 is proportional to the change in the rectified line
voltage.
At the point of return ICBU208
the peak collector current has been reduced with the aid of the given
values from 5.2 A at 90 Vac to 3.3 A at 270 Vac. The transmissible power at the point of return
remains stable between 125 and 270 Vac due to the set activation point of the point of return
correction (unbroken curve in figure 2).
Version 2.0 28 1 Jun 1994
TDA 4601
Load Characteristics
Figure 1
Figure 2
Qualität hat für uns eine umfassende
Bedeutung. Wir wollen al len Ihren
Ansprüchen in der bestmöglichen
Weise gerecht werden. Es geht uns also
nicht nur um die Produktqualit ät
unsere Anstrengungen gelten
gleichermaßen der Lieferqualität und
Logistik, dem Service und Support
sowie allen sonstigen Beratungs- und
Betreuungsleistungen.
Dazu gehört eine bestimmte
Geisteshaltung unserer Mitarbeiter.
Total Quality im Denken und Handeln
gegenüber Kollegen, Lieferanten und
Ihnen, unserem Kunden. Unsere
Leitlinie is t jede Aufgabe mit „Null
Fehlern“ zu lösen – in offener
Sichtweise auch über den eigenen
Arbeitsplatz hinaus – und uns ständig
zu verbessern.
Unternehmensweit orientieren wir uns
dabei auch an „top“ (Time Optimized
Processes), um Ihnen durch größere
Schnelligkeit den entscheidenden
Wettbewerbsvorsprung zu verschaffen.
Geben Sie uns die Ch ance, hohe
Leistung durch u mfassende Qualitä t zu
beweisen.
Wir werden Sie überzeugen.
Quality takes on an allencompassing
significance at Semiconductor Group.
For us it means living up to each and
every one of your demands in the best
possible way. So we are not only
concerned with product quality. We
direct our efforts eq ually at quality of
supply and logistics, service and
support, as well as all the other ways i n
which we advise and attend to you.
Part of t his is the very sp ecial attitude of
our staff. Total Quality in thought and
deed, towards co-workers, suppliers
and you, our c ustomer. Our gui deline is
“do everything with zero defects”, in an
open manner that is demonstrated
beyond your immediat e workplace, and
to constantly improve.
Throughout the corporation we also
think in terms of Time Optimized
Processes (top), greater sp eed on our
part to give you that decisive
competitive edge.
Give us the chance t o prove the bes t of
performance through the best of quality
– you will be convinced.
http://www.infineon.com
Total Quality Management
Published by Infineon Technologies AG