VALU-BEAM(R) Sensors VALU-BEAM(R) Sensors 912 Series with Solid-State Outputs . . . . . . . . . . . 328 915 Series with Electromechanical Relay Output . . . 338 990 Series with Built-in 6-Digit Totalizing Counter . . 348 SMI912 Series Intrinsically Safe Sensors . . . . . . . . 356 SM91EN/RN Series for Enhanced Sunlight Immunity . . . 364 VALU-BEAM Accessories . . . . . . . . . . . . . . . . . . . 368 ! (Exceptions noted) VALU-BEAM sensors are not suitable for use in personnel safety applications! See WARNING on inside front cover of catalog. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 327 VALU-BEAM(R) 912 Series Sensors VALU-BEAM 912 Series Sensors With Solid-State Outputs * * VALU-BEAM 912 cabled diffuse mode (left) and quick-disconnect glass fiber optic mode (right) shown Choose models for 10 to 30V dc or 24 to 250V ac operation DC models have bipolar solid-state outputs: one NPN (sinking) and one PNP (sourcing) AC models have a SPST solid-state output rated for up to 3 /4 amp with simple 2-wire hookup All models have a rear panel sensitivity adjustment and light/dark operate switch DC models include Banner's exclusive Alignment Indicating Device system (AIDTM) Choose models with integral 2 m (6.5') cable or mini-style QD (quick-disconnect) connector; 9 m (30') cables are also available * * * * U. S. Patent #4356393 912 Series Sensing Mode Options Opposed Retroreflective Diffuse Convergent Glass Fiber Optic Infrared, 880 nm 912 Series Opposed Mode Emitter (E) and Receiver (R) Models Range SMA91E SM91R SMA91EQD SM91RQD Supply Voltage Cable 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 4-Pin Mini QD 60 m (200') Emitter: 10-250V ac/dc Bipolar Receiver: NPN/PNP 10-30V dc SMA91E SM2A91R SMA91EQD SM2A91RQD 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 3-Pin Mini QD Emitter: 10-250V ac/dc Receiver: 24-250V ac SMA91ESR SM91RSR SMA91ESRQD SM91RSRQD 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 4-Pin Mini QD Emitter: 10-250V ac/dc Receiver: 10-30V dc SMA91ESR SM2A91RSR SMA91ESRQD SM2A91RSRQD 328 3m (10') 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 3-Pin Mini QD Output Type Emitter: 10-250V ac/dc Receiver: 24-250V ac SPST SCR Solid-state 2-Wire Excess Gain Beam Pattern Effective Beam: 13 mm 1000 E X C E S S G A I N 1500 mm SMA91E / SM91R, SMA91E / SM2A91R 60.0 in 1000 mm Opposed Mode 40.0 in 100 10 500 mm SMA91E & SM91R, SMA91E & SM2A91R Opposed Mode 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft 20.0 in 0 0 500 mm 20.0 in 1000 mm 40.0 in 1500 mm 60.0 in 0 100 m 330 ft 15 m 50 ft 30 m 100 ft 1000 Bipolar NPN/PNP SPST SCR Solid-state 2-Wire E X C E S S G A I N 45 m 150 ft 60 m 200 ft 75 m 250ft DISTANCE DISTANCE Effective Beam: 3.5 mm SMA91ESR / SM91RSR, SMA91ESR / SM2A91RSR 300 mm 100 12.0 in Opposed Mode 200 mm 8.0 in 100 mm 4.0 in 0 10 SMA91ESR & SM91RSR, SMA91ESR & SM2A91RSR 1 .01 m .033 ft 1.0 m 3.3 ft DISTANCE 4.0 in 200 mm 8.0 in 300 mm Opposed Mode .10 m .33 ft 0 100 mm 10 m 33 ft 12.0 in 0 .6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10ft DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 912 Series Sensors P Visible red, 650 nm Non-Polarized Polarized NOTE: Retroreflective range is specified using one model BRT-3 retroreflector (3" diameter). Actual sensing range may be more or less than specified, depending upon the efficiency and reflective area of the retroreflector(s) in use. See page 722 for more information. Non-Polarized, Polarized 912 Series Retroreflective Mode Models Range Cable Supply Voltage Output Type 2 m (6.5') 4-Pin Mini QD 10-30V dc 0.15 - 9 m (6" - 30') SM2A912LV SM2A912LVQD 2 m (6.5') 3-Pin Mini QD 24-250V ac Bipolar NPN/PNP SPST SCR Solid-state 2-Wire 2 m (6.5') 4-Pin Mini QD 10-30V dc 0.3 - 4.5 m (1 - 15') SM2A912LVAG SM2A912LVAGQD 2 m (6.5') 3-Pin Mini QD E X C E S S SM912LV, SM2A912LV Retroreflective Mode SM912LV, SM2A912LV 150 mm With BRT-3 Reflector 6.0 in Retroreflective Mode 100 100 mm 4.0 in 50 mm 2.0 in 0 0 G A I N 10 2.0 in 50 mm 100 mm 4.0 in With BRT-3 Reflector 6.0 in 150 mm 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft 0 10 m 33 ft 2m 6.6 ft 4m 13 ft 6m 20 ft 8m 26 ft 10 m 33 ft DISTANCE DISTANCE 1000 Polarized* SM912LVAG SM912LVAGQD Beam Pattern 1000 Non-Polarized SM912LV SM912LVQD Excess Gain 24-250V ac Bipolar NPN/PNP SPST SCR Solid-state 2-Wire E X C E S S SM912LVAG, SM2A912LVAG Retroreflective Mode SM912LVAG, SM2A912LVAG 75 mm W/BRT-3 Reflector 3.0 in Retroreflective Mode 100 50 mm 2.0 in 25 mm 1.0 in 0 G A I N 10 0 25 mm With BRT-3 Reflector 50 mm 2.0 in 75 mm 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft DISTANCE 10 m 33 ft 1.0 in 3.0 in 0 1m 3.3 ft 2m 6.6 ft 3m 10 ft 4m 13 ft 5m 16 ft DISTANCE *Use polarized models when shiny objects will be sensed For VALU-BEAM 912 Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SM912LV W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 329 VALU-BEAM(R) 912 Series Sensors Infrared, 880 nm 912 Series Diffuse Mode Models Range Supply Voltage Cable Output Type Excess Gain Beam Pattern Performance based on 90% reflectance white test card 1000 SM912D SM912DQD 2 m (6.5') 4-Pin Mini QD 10-30V dc Bipolar NPN/PNP 760 mm (30") SM2A912D SM2A912DQD E X C E S S SM912D SM2A912D Diffuse Mode SM912D, SM2A912D 18 mm 100 0.75 in Diffuse Mode 12 mm 0.50 in 6 mm 0.25 in 0 2 m (6.5') 3-Pin Mini QD 24-250V ac SPST SCR Solid-state 2-Wire G A I N 0 10 6 mm 0.25 in 12 mm 0.50 in 18 mm 1 1 mm .04 in 10 mm .4 in 100 mm 4 in 1000 mm 40 in 0.75 in 0 150 mm 300 mm 450 mm 600 mm 750 mm 6 in 12 in 18 in 24 in 30 in DISTANCE DISTANCE 1000 SM912DSR SM912DSRQD 2 m (6.5') 4-Pin Mini QD 10-30V dc Bipolar NPN/PNP 380 mm (15") SM2A912DSR SM2A912DSRQD E X C E S S SM912DSR SM2A912DSR Diffuse Mode SM912DSR/SM2A912DSR 18 mm 0.75 in Diffuse Mode 100 12 mm 0.50 in 6 mm 0.25 in 0 2 m (6.5') 3-Pin Mini QD 24-250V ac SPST SCR Solid-state 2-Wire G A I N 10 0 6 mm 0.25 in 12 mm 0.50 in 18 mm 1 1 mm .04 in 10 mm .4 in 100 mm 4 in 0.75 in 0 1000 mm 40 in 75 mm 150 mm 225 mm 300 mm 375 mm 3 in 6 in 9 in 12 in 15 in DISTANCE DISTANCE See Sensing Beam Information Below 912 Series Convergent Mode Models Focus Supply Voltage Cable Output Type SM2A912CV SM2A912CVQD 38 mm (1.5") Spot Size at Focus: 1.5 mm (0.06") 2 m (6.5') 4-Pin Mini QD 2 m (6.5') 3-Pin Mini QD 10-30V dc 24-250V ac Bipolar NPN/PNP SPST SCR Solid-state 2-Wire 2 m (6.5') 4-Pin Mini QD 10-30V dc 38 mm (1.5") SM2A912C SM2A912CQD 330 2 m (6.5') 3-Pin Mini QD Performance based on 90% reflectance white test card E X C E S S G A I N SM912CV, SM2A912CV, Convergent Mode 100 SM912CV, SM2A912CV 2.4 mm 0.09 in Convergent Mode 1.6 mm 0.06 in 0.8 mm 0.03 in 0 10 0 0.8 mm 0.03 in 1.6 mm 0.06 in 2.4 mm 1 1 mm .04 in 10 mm .4 in 100 mm 4 in 1000 mm 40 in 0.09 in 0 12.5 mm 25 mm 37.5 mm 50 mm 62.5 mm 0.50 in 1.0 in 1.5 in 2.0 in 2.5 in DISTANCE DISTANCE 1000 Infrared 880 nm SM912C SM912CQD Beam Pattern 1000 Visible Red 650 nm SM912CV SM912CVQD Excess Gain 24-250V ac Bipolar NPN/PNP SPST SCR Solid-state 2-Wire E X C E S S SM912C SM2A912C Convergent Mode SM912C, SM2A912C 2.4 mm 100 0.09 in Convergent Mode 1.6 mm 0.06 in 0.8 mm 0.03 in 0 G A I N 10 0 0.8 mm 0.03 in 1.6 mm 0.06 in 2.4 mm 1 1 mm .04 in 10 mm .4 in 100 mm 4 in DISTANCE 1000 mm 40 in 0.09 in 0 15 mm 0.60 in 30 mm 1.2 in 45 mm 1.8 in 60 mm 2.4 in 75 mm 3.0 in DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 912 Series Sensors Infrared 880 nm 912 Series Glass Fiber Optic Emitter (E) and Receiver (R) Models SMA91EF SM91RF SMA91EFQD SM91RFQD SMA91EF SM2A91RF SMA91EFQD SM2A91RFQD Range Range varies with fiber used Cable 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 4-Pin Mini QD 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 3-Pin Mini QD Supply Voltage Emitter: 10-250V ac/dc Receiver: 10-30V dc Emitter: 10-250V ac/dc Receiver: 24-250V ac Output Type Excess Gain Beam Pattern 1000 E X C E S S Bipolar NPN/PNP SMA91EF & SM91RF, SMA91EF & SM2A91RF Opposed Mode 12 in Opposed Mode 8 in 200 mm 100 mm IT23S Fibers W/L16F Lenses 10 G A I N SPST SCR Solid-state 2-Wire SMA91EF & SM91RF, SMA91EF & SM2A91RF 300 mm 100 0 100 mm 1 0.1 m 0.33 ft 0 4 in IT23S Fibers With L16F lenses 200 mm IT23S Fibers W/L9 Lenses 4 in IT23S Fibers With L9 lenses 8 in 12 in 300 mm 1.0 m 3.3 ft 10 m 33 ft 100 m 330 ft 0 2.4 m 8 ft 4.8 m 16 ft DISTANCE 7.2 m 24 ft 9.6 m 32 ft 12 m 40 ft DISTANCE Infrared 880 nm 912 Series Glass Fiber Optic Mode Models Range Cable Supply Voltage Excess Gain Output Type Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 2 m (6.5') 4-Pin Mini QD SM912F SM912FQD 10-30V dc Bipolar NPN/PNP SM912F SM2A912F Opposed Mode SM912F/SM2A912F 75 mm 100 IT23S Fibers 2 in 1 in 0 G A I N 3 in Opposed Mode 50 mm 25 mm 10 IT13S Fibers IT13S IT23S 10 mm .4 in 100 mm 4 in 0 25 mm 1 in 50 mm 2 in 75 mm 1 1 mm .04 in Range varies with fiber optics used. SM2A912F SM2A912FQD E X C E S S 3 in 0 1000 mm 40 in 100 mm 200 mm 300 mm 400 mm 500 mm 4 in 8 in 12 in 16 in 20 in DISTANCE DISTANCE 1000 2 m (6.5') 3-Pin QD 24-250V ac SPST SCR Solid-state 2-Wire E X C E S S G A I N SM912F SM2A912F Diffuse Mode 1.9 mm 100 0.075 in SM912F/SM2A912F 1.3 mm 0.050 in Diffuse Mode 0.65 mm 10 BT13S Fiber 1 1 mm .04 in 0.025 in 0 BT23S Fiber BT13S BT23S 0.025 in 1.3 mm 0.050 in 1.9 mm 10 mm .4 in 100 mm 4 in DISTANCE 1000 mm 40 in 0 0.65 mm 0.075 in 0 7.5 mm 0.3 in 15 mm 22.5 mm 30 mm 37.5 mm 0.6 in 0.9 in 1.2 in 1.5 in DISTANCE For VALU-BEAM 912 Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SM912D W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 331 VALU-BEAM(R) 912 Series Sensors 912 Series DC Specifications Supply Voltage and Current 10 to 30V dc at 20 mA maximum, exclusive of load (except for SMA91E, ESR and EF emitters, which operate from 10 to 250V ac or dc, 10 mA max.) Supply Protection Circuitry Protected against reverse polarity and transient voltages Output Configuration Bipolar: One current sourcing (PNP) and one current sinking (NPN) open-collector transistor Output Rating 250 mA continuous, each output Off-state leakage current less than 10 microamps Output saturation voltage (PNP output) less than 1 volt at 10 mA and less than 2 volts at 250 mA Output saturation voltage (NPN output) less than 200 millivolts at 10mA and less than 1 volt at 250 mA Output Protection Circuitry Protected against false pulse on power-up and continuous overload or short-circuit of outputs Output Response Time 4 milliseconds ON/OFF (except receiver-only units which are 8 milliseconds ON and 4 milliseconds OFF); independent of signal strength (NOTE: 100 millisecond delay on power-up; outputs non-conducting during this time) Repeatability Opposed and Glass Fiber Optic Emitter-Receiver pairs: 1.0 millisecond; Retro, Diffuse, Convergent and Glass Fiber Optic: 1.3 milliseconds Adjustments LIGHT/DARK OPERATE select switch and SENSITIVITY control potentiometer, both located at rear of sensor Indicators Exclusive, patented Alignment Indicating Device (AIDTM, US patent #4356393) lights a top mounted red LED indicator whenever the sensor sees a "light" condition, with a superimposed pulse rate proportional to the light signal strength (the stronger the signal, the faster the pulse rate). Models SMA91E & SM91ESR emitter have a visible-red "tracer beam" which indicates "power on" and enables easy "line-ofsight" alignment. Construction Reinforced thermoplastic polyester housing, totally encapsulated, molded acrylic lenses and stainless steel hardware Environmental Rating Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 12 and 13; IEC IP66 Connections PVC-jacketed 2 m (6.5') or 9 m (30') cables or 4-pin mini-style quick-disconnect (QD) fitting available. Note: Opposed mode emitters use 3-pin mini-style QD fitting. See page 368 and the Accessories section. Operating Conditions Temperature: -20 to +70 C (-4 to +158F) Maximum relative humidity: 90% at 50C (non-condensing) Certifications 332 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 912 Series Sensors 912 Series DC Hookup Diagrams DC Sensors with Attached Cable bn bk bn + 10-30V dc - bu wh DC Sensors with Quick-Disconnect (4-Pin Mini-Style) wh Load bk Load Emitters with Attached Cable bn bu + 10-30V dc - bu Load Load Emitters with Quick-Disconnect (3-Pin Mini-Style) bn + bu 10-250V ac/dc - + 10-250V ac/dc - bk 3-Pin Mini-Style Pin-out 4-Pin Mini-Style Pin-out (Cable Connector Shown) (Cable Connector Shown) Black Wire Blue Wire White Wire Brown Wire Brown Wire Black Wire Blue Wire Quick-Disconnect (QD) Option DC 912 Series VALU-BEAM sensors are sold with either a 2 m (6.5') or a 9 m (30') attached PVC-covered cable, or with a 4-pin mini-style QD cable fitting. Opposed mode emitters use 3-pin mini-style QD cable fitting. DC QD sensors are identified by the letters "QD" in their model number suffix. Mating cable for QD 912 Series sensors is model MBCC-412. Mating cable for opposed mode emitters is model MBCC-312. Cables are supplied in a standard length of 4 m (12'). For more information on QD cables, see page 368 and the Accessories section. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 333 VALU-BEAM(R) 912 Series Sensors 912 Series AC Specifications Supply Voltage and Current 24 to 250V ac (50/60 Hz), except for SMA91E, ESR and EF emitters, which operate from 10 to 250V ac or dc Supply Protection Circuitry Protected against transient voltages Output Configuration SPST SCR solid-state relay with either normally closed or normally open contact (light/dark operate selectable); 2-wire hookup Output Rating Minimum load current 10 mA, max. steady-state load capability 750 mA to 50C ambient (122F), 500 mA to 70C ambient (158F) Inrush capability 4 amps for 1 sec. (non-repetitive) Off-state leakage current less than 1.7 mA rms On-state voltage drop 5 volts rms at 750 mA load, 10 volts rms at 15 mA load Output Protection Circuitry Protected against false pulse on power-up Output Response Time 8 milliseconds ON and OFF (except receiver-only units, which are 8 milliseconds 0N and 4 milliseconds OFF; independent of signal strength OFF time does not include load response of up to 1/2 ac cycle (8.3 milliseconds) Response time specification of the load should be considered when important (NOTE: 300 millisecond delay on power-up; outputs are non-conducting during this time) Repeatability Opposed and Glass Fiber Optic Emitter-Receiver pairs: 1.0 millisecond; Retro, Diffuse, Convergent and Glass Fiber Optic: 2.6 milliseconds Adjustments LIGHT/DARK OPERATE select switch and SENSITIVITY control potentiometer, both located at rear of sensor Indicators Top-mounted red LED indicator lights when output is conducting. Models SMA91E & SM91ESR emitter have a visible-red "tracer beam" which indicates "power on" and enables easy "line-of-sight" alignment. Construction Reinforced thermoplastic polyester housing, totally encapsulated, molded acrylic lenses and stainless steel hardware Environmental Rating Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 12 and 13; IEC IP66 Connections PVC-jacketed 2 m (6.5') or 9 m (30') cables or 3-pin mini-style quick-disconnect (QD) fitting available. See page 368 and the Accessories section. Operating Conditions Temperature: -20 to +70 C (-4 to +158F) Maximum relative humidity: 90% at 50C (non-condensing) Application Notes i) 912 Series ac sensors may be destroyed from overload conditions ii) Use on low voltage requires careful analysis of the load to determine if the leakage current or on-state voltage of the sensor will interfere with proper operation of the load iii) The false-pulse protection feature may cause momentary drop-out of the load when the sensor is wired in series or parallel with mechanical switch contacts Certifications 334 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 912 Series Sensors 912 Series AC Hookup Diagrams AC Sensors with Attached Cable AC Sensors with Quick-Disconnect (3-Pin Mini-Style) bn bn bu 24-250V ac bu Load bk Emitters with Attached Cable bn bu + 24-250V ac Load - Emitters with Quick-Disconnect (3-Pin Mini-Style) bn + bu 10-250V ac/dc - + 10-250V ac/dc - bk Mini-Style Pin-out (Cable Connector Shown) Black Wire Blue Wire Brown Wire Quick-Disconnect (QD) Option AC 912 Series VALU-BEAM sensors are sold with either a 2 m (6.5') or a 9 m (30') attached PVC-covered cable, or with a 3-pin mini-style QD cable fitting. AC QD sensors are identified by the letters "QD" in their model number suffix. Mating cables for QD 912 Series sensors are model MBCC-312. Cables are supplied in a standard length of 4 m (12'). For more information on QD cables, see page 368 and the Accessories section. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 335 VALU-BEAM(R) 912 Series Sensors 912 Series Dimensions 912 Series Opposed, Retro, and Diffuse Sensing Modes (model suffix E, ESR, R, RSR, LV, D & DSR) 912 Series Sensor with Attached Cable 912 Series Sensor with Quick-Disconnect LED Indicator 36.6 mm (1.44") 35.6 mm (1.40") Lens Centerline 50.8 mm (2.00") 39.1 mm (1.54") 12.7 mm (0.50") M30 x 1.5 Thread Hex Nut Supplied 26.7 mm (1.05") Mini-style Quick-disconnect M30 x 1.5 External Thread 1/2" - 14 NPSM Internal Thread Hex Nut Supplied 912 Series Sensor - Glass Fiber Optic (model suffix F, EF & RF) 912 Series Sensor - Convergent Sensing Mode (model suffix LVAG, C & CV) 39.6 mm (1.56") 42.2 mm (1.66") Fiber Port Centerline 912 Series Sensor - Rear View Light/Dark Operate (L.O. = CW, D.O. = CCW) Remove Screws to Access Controls Sensitivity Control (Turn CW to Increase) 17.8 mm (0.70") 4.5 mm (#10) Screw Clearance (2) 5.6 mm (0.22") 25.4 mm (1.00") 336 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 912 Series Sensors NOTES: Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 337 VALU-BEAM(R) 915 Series Sensors VALU-BEAM 915 Series Sensors with Electromechanical Relay Output VALU-BEAM 915 Series quick-disconnect (left) and cabled (right) versions shown * Models available for either 12 to 28V ac/dc, 90 to 130V ac, or 210 to 250V ac * SPDT electromechanical relay output is rated for up to 5 amps switching capacity * Rear panel sensitivity adjustment; top-mounted alignment indicator * Choose models with integral 2 m (6.5') cable or mini-style QD (quick-disconnect) connector; 9 m (30') cables are also available 915 Series Sensing Mode Options Opposed Retroreflective Diffuse Convergent Glass and Plastic Fiber Optic Infrared, 880 nm 915 Series Opposed Mode Emitter (E) and Receiver (R) Models Range SMA91E SMW95R SMA91EQD SMW95RQD SMA91E SMA95R SMA91EQD SMA95RQD Supply Voltage Cable 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 5-Pin Mini QD 60 m (200') 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 5-Pin Mini QD Output Type 1000 E X C E S S SPDT E/m Relay G A I N 100 SMA91E & SMW95R or SMA95R or SMB95R 338 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 5-Pin Mini QD 1500 mm SMA91E with SMW95R or SMA95R or SMB95R 60.0 in 1000 mm Opposed Mode 40.0 in 20.0 in 500 mm 10 0 0 Opposed Mode 500 mm 20.0 in 1000 mm 40.0 in 60.0 in 1500 mm 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft DISTANCE SMA91E SMB95R SMA91EQD SMB95RQD Beam Pattern Effective Beam: 13 mm Emitter: 10-250V ac/dc Receiver: 12-28V ac/dc Emitter: 10-250V ac/dc Receiver: 90-130V ac Excess Gain 100 m 330 ft 0 15 m 50 ft 30 m 100 ft 45 m 150 ft 60 m 200 ft 75 m 250ft DISTANCE Emitter: 10-250V ac/dc Receiver: 210-250V ac Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 915 Series Sensors Infrared 880 nm 915 Series Opposed Mode Emitter (E) and Receiver (R) Models Range SMA91ESR SMW95RSR SMA91ESRQD SMW95RSRQD SMA91ESR SMA95RSR SMA91ESRQD SMA95RSRQD SMA91ESR SMB95RSR SMA91ESRQD SMB95RSRQD Cable 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 5-Pin Mini QD 3m (10') 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 5-Pin Mini QD 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 5-Pin Mini QD Supply Voltage Output Type Excess Gain Emitter: 10-250V ac/dc Receiver: 12-28V dc Emitter: 10-250V ac/dc Receiver: 90-130V ac Emitter: 10-250V ac/dc Receiver: 210-250V ac Beam Pattern Effective Beam: 3.5 mm 1000 SPDT E/m Relay E X C E S S G A I N SMA91ESR & SMW95RSR or SMA95RSR or SMB95RSR 100 Opposed Mode SMA91ESR with SMW95RSR or SMA95RSR / SMB95RSR 300 mm 12.0 in Opposed Mode 200 mm 8.0 in 4.0 in 100 mm 0 0 10 100 mm 4.0 in 200 mm 8.0 in 12.0 in 300 mm 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft DISTANCE 10 m 33 ft 0 .6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10ft DISTANCE For VALU-BEAM 915 Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SMA91E W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 339 VALU-BEAM(R) 915 Series Sensors Non-Polarized, Polarized NOTE: Retroreflective range is specified using one model BRT-3 retroreflector (3" diameter). Actual sensing range may be more or less than specified, depending upon the efficiency and reflective area of the retroreflector(s) in use. See page 722 for more information. P Visible red, 650 nm Non-Polarized Polarized 915 Series Retroreflective Mode Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Non-Polarized SMW915LV SMW915LVQD SMA915LV SMA915LVQD 1000 2 m (6.5') 12-28V ac/dc 5-Pin Mini QD 0.15 - 9 m (6" - 30') 2 m (6.5') 5-Pin Mini QD 90-130V ac SPDT E/m Relay E X C E S S SMW915LV, SMA915LV, SMB915LV 100 with BRT-3 reflector Retroreflective Mode 10 4.0 in 50 mm 2.0 in 0 2.0 in 50 mm 100 mm With BRT-3 Reflector 2 m (6.5') 210-250V ac 5-Pin Mini QD 1.0 m 3.3 ft 0 10 m 33 ft 4.0 in 6.0 in 150 mm .10 m .33 ft 6.0 in 100 mm 0 G A I N 1 .01 m .033 ft SMB915LV SMB915LVQD SMW915LV, SMA915LV, SMB915LV 150 mm Retroreflective Mode 2m 6.5 ft 4m 13 ft 6m 20 ft 8m 26 ft 10 m 33 ft DISTANCE DISTANCE Polarized* SMW915LVAG SMW915LVAGQD SMA915LVAG SMA915LVAGQD SMB915LVAG SMB915LVAGQD 1000 2 m (6.5') 12-28V ac/dc 5-Pin Mini QD 0.3 - 4.5 m (1 - 15') 2 m (6.5') 5-Pin Mini QD 90-130V ac 2 m (6.5') 210-250V ac 5-Pin Mini QD SPDT E/m Relay E X C E S S G A I N SMW915LVAG, SMA915LVAG, SMB915LVAG 100 SMW915LVAG, SMA915LVAG, SMB915LVAG 75 mm Retroreflective Mode Retroreflective Mode 50 mm 2.0 in 1.0 in 25 mm with BRT-3 reflector 0 0 10 25 mm With BRT-3 Reflector 3.0 in 75 mm .10 m .33 ft 1.0 m 3.3 ft DISTANCE 10 m 33 ft 1.0 in 2.0 in 50 mm 1 .01 m .033 ft 3.0 in 0 1m 3.3 ft 2m 6.6 ft 3m 10 ft 4m 13 ft 5m 16 ft DISTANCE *Use polarized models when shiny objects will be sensed For VALU-BEAM 915 Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SMW915D W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. 340 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 915 Series Sensors Infrared 880 nm 915 Series Diffuse Mode Models Range SMW915D SMW915DQD Cable 2 m (6.5') 5-Pin Mini QD Supply Voltage Output Type Excess Gain Beam Pattern Performance based on 90% reflectance white test card 12-28V ac/dc 1000 SMA915D SMA915DQD 760 mm (30") 2 m (6.5') 5-Pin Mini QD 90-130V ac SMB915D SMB915DQD 2 m (6.5') 5-Pin Mini QD 210-250V ac SMW915DSR SMW915DSRQD 2 m (6.5') 5-Pin Mini QD 12-28V ac/dc SPDT E/m Relay E X C E S S SMW915D, SMA915D, SMB915D 100 Diffuse Mode SMW915D, SMA915D, SMB915D 18 mm Diffuse Mode 0.50 in 6 mm 0.25 in 0 G A I N 10 0 6 mm 0.25 in 12 mm 0.50 in 18 mm 1 1 mm .04 in 10 mm .4 in 100 mm 4 in 0.75 in 12 mm 0.75 in 0 1000 mm 40 in DISTANCE 150 mm 300 mm 450 mm 600 mm 750 mm 6 in 12 in 18 in 24 in 30 in DISTANCE 1000 SMA915DSR SMA915DSRQD SMB915DSR SMB915DSRQD 380 mm (15") 2 m (6.5') 5-Pin Mini QD 2 m (6.5') 5-Pin Mini QD 90-130V ac 210-250V ac SPDT E/m Relay E X C E S S G A I N SMW915DSR SMA915DSR SMB915DSR Diffuse Mode 100 SMW915DSR, SMA915DSR, SMB915DSR 18 mm 12 mm 0.50 in 6 mm Diffuse Mode 0 10 10 mm .4 in 100 mm 4 in DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 1000 mm 40 in 0.25 in 0 6 mm 0.25 in 12 mm 0.50 in 18 mm 1 1 mm .04 in 0.75 in 0.75 in 0 75 mm 150 mm 225 mm 300 mm 375 mm 3 in 6 in 9 in 12 in 15 in DISTANCE 341 VALU-BEAM(R) 915 Series Sensors Visible red 650 nm 915 Series Convergent Mode Models Focus SMW915CV SMW915CVQD Supply Voltage Cable 2 m (6.5') 5-Pin Mini QD Output Type Excess Gain Beam Pattern Performance based on 90% reflectance white test card 12-28V ac/dc 1000 38 mm (1.5") SMA915CV SMA915CVQD Spot Size at Focus: 1.5 mm (0.06") 2 m (6.5') 5-Pin Mini QD G A I N SMW915CV, SMA915CV, SMB915CV Convergent Mode 100 SMW915CV, SMA915CV, SMB915CV 2.4 mm 0.06 in 0.8 mm 0.03 in 0 0.8 mm 0.03 in 1.6 mm 0.06 in 2.4 mm 10 mm .4 in 100 mm 4 in 0.09 in Convergent Mode 1.6 mm 0 10 1 1 mm .04 in 2 m (6.5') 5-Pin Mini QD SMB915CV SMB915CVQD 90-130V ac SPDT E/m Relay E X C E S S 1000 mm 40 in 0.09 in 0 12.5 mm 25 mm 37.5 mm 50 mm 62.5 mm 0.50 in 1.0 in 1.5 in 2.0 in 2.5 in DISTANCE DISTANCE 210-250V ac Infrared, 880 nm 915 Series Glass Fiber Optic Mode Models Range Supply Voltage Cable Output Type Excess Gain Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 SMW915F SMW915FQD SMA915F SMA915FQD SMB915F SMB915FQD 2 m (6.5') 5-Pin Mini QD Range varies by sensing mode and fiber used. E X C E S S 12-28V ac/dc G A I N 2 m (6.5') 5-Pin Mini QD 90-130V ac SPDT E/m Relay 210-250V ac IT23S Fibers Opposed Mode 50 mm Opposed Mode Glass Fibers 10 mm .4 in 1 in 0 10 IT13S IT23S 0 25 mm 1 in 50 mm 2 in 75 mm 100 mm 4 in 3 in 2 in 25 mm IT13S Fibers 3 in 0 1000 mm 40 in 100 mm 200 mm 300 mm 400 mm 500 mm 4 in 8 in 12 in 16 in 20 in DISTANCE DISTANCE 1000 G A I N SMW915F SMA915F, SMB915F 1.9 mm 100 Diffuse Mode Glass Fibers BT13S Fiber BT13S BT23S 100 mm 4 in DISTANCE 1000 mm 40 in 0.025 in 0 0.65 mm 0.025 in 1.3 mm 0.050 in 1.9 mm 10 mm .4 in 0.050 in Diffuse Mode 0 BT23S Fiber 10 0.075 in SMW915F, SMA915F, SMB915F 1.3 mm 0.65 mm 1 1 mm .04 in 342 SMW915F, SMA915F, SMB915F 75 mm 100 1 1 mm .04 in E X C E S S 2 m (6.5') 5-Pin Mini QD SMW915F SMA915F, SMB915F 0.075 in 0 7.5 mm 0.3 in 15 mm 22.5 mm 30 mm 37.5 mm 0.6 in 0.9 in 1.2 in 1.5 in DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 915 Series Sensors Visible red, 650 nm 915 Series Plastic Fiber Optic Mode Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 SMW915FP SMW915FPQD 2 m (6.5') 5-Pin Mini QD E X C E S S 12-28V ac/dc SMW915FP, SMA915FP, SWB915FP Opposed Mode Plastic Fibers SMA915FP SMA915FPQD SMB915FP SMB915FPQD Range varies by sensing mode and fiber used. PIT26U Fibers 90-130V ac SPDT E/m Relay 100 mm 4.0 in 0.6 in 30 mm 1.2 in 1.8 in 0 1000 mm 40 in 25 mm 1 in 50 mm 2 in 75 mm 100 mm 125 mm 3 in 4 in 5 in DISTANCE 1000 100 Diffuse Mode Plastic Fibers SMW915FP, SMA915FP, SMB915FP SMW915FP, SMA915FP, SMB915FP 3.8 mm G A I N 0.15 in Diffuse Mode 2.5 mm PBT46U Fiber 0.10 in 1.2 mm 0.05 in 0 210-250V ac 0 15 mm DISTANCE E X C E S S 2 m (6.5') 5-Pin Mini QD 0.6 in PIT46U PIT26U 45 mm 10 mm .40 in 1.8 in 1.2 in 0 10 1 1 mm .04 in 2 m (6.5') 5-Pin Mini QD Opposed Mode 30 mm 15 mm PIT46U Fibers G A I N SMW915FP, SMA915FP, SMB915FP 45 mm 100 10 PBT26U Fiber 1 .1 mm .004 in 1 mm .04 in 10 mm .40 in DISTANCE PBT26U PBT46U 0.05 in 2.5 mm 0.10 in 3.8 mm 100 mm 4.0 in 0 1.2 mm 0.15 in 0 7.5 mm 0.3 in 15 mm 22.5 mm 30 mm 37.5 mm 0.6 in 0.9 in 1.2 in 1.5 in DISTANCE For VALU-BEAM 915 Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SMW915FP W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 343 VALU-BEAM(R) 915 Series Sensors 915 Series Specifications Supply Voltage and Current SMW915 Series: 12 to 28V ac or dc at 50 mA maximum, exclusive of load SMA915 Series: 90 to 130V ac (50-60 Hz) at 20 mA maximum, exclusive of load SMB915 Series: 210 to 250V ac (50-60 Hz) at 20 mA maximum, exclusive of load Exceptions: SMA91E and ESR emitters, which operate from 10-250V ac (50-60 Hz) or dc (10 mA max.) Supply Protection Circuitry Protected against transient voltages Output Configuration One internal "form C" (single-pole double-throw) electromechanical relay Output Rating Max. switching power (resistive load) = 150 W, 600 VA Max. switching voltage (resistive load) = 250V ac or 30 V dc (120V ac max. per UL & CSA) Max. switching current (resistive load) = 5A Min.. voltage and current = 1 amp at 5V dc, 0.1 amp at 24V dc Peak switching voltage = 750V ac (transient suppression recommended) Mechanical life of relay = 10,000,000 operations Output Protection Circuitry Protected against false pulse on power-up Output Response Time 20 milliseconds ON and OFF; independent of signal strength (NOTE: 100 millisecond relay on power-up; relay de-energized during this time) Adjustments SENSITIVITY control on rear of sensor allows precise gain setting (turn clockwise to increase gain) Indicators Top-mounted red LED indicator lights whenever the sensor sees "light" condition. Models SMA91E and SMA91ESR emitters have visible-red "tracer beam" which indicates "power on" and enables easy "line-of-sight" alignment. Construction Reinforced black thermoplastic polyester housing, totally encapsulated, molded acrylic lenses and stainless steel hardware Environmental Rating Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 12 and 13; IEC IP66 Connections PVC-jacketed 2 m (6.5') or 9 m (30') cable or 5-pin mini-style quick-disconnect (QD) fitting available. See page 368 and Accessories section. Operating Conditions Temperature: -40 to +50 C (-40 to +122F) Maximum relative humidity: 90% at 50C (non-condensing) Application Notes Install transient suppressor (MOV) across any output contact which switches an inductive load Certifications 344 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 915 Series Sensors 915 Series Hookup Diagrams Sensors with Attached Cable bn bu wh Sensors with Quick-Disconnect (5-Pin Mini-Style) bn + bu Supply Voltage* - wh NC ye C bk NO + Supply Voltage* - NC ye C bk NO *see Specifications *see Specifications Emitters with Attached Cable Emitters with Quick-Disconnect (3-Pin Mini-Style) bn bn bu + + 10-250V ac/dc - bu 10-250V ac/dc - bk 3-Pin Mini-Style Pin-out 5-Pin Mini-Style Pin-out (Cable Connector Shown) (Cable Connector Shown) White Wire Black Wire Blue Wire Brown Wire Brown Wire Black Wire Blue Wire Yellow Wire Quick-Disconnect (QD) Option 915 Series VALU-BEAM sensors are sold with either a 2 m (6.5') or a 9 m (30') attached PVC-covered cable, or with a 5-pin mini-style QD cable fitting. Opposed mode emitters use 3-pin mini-style QD cable fitting. QD sensors are identified by the letters "QD" in their model number suffix. Mating cables for QD 915 Series sensors are model MBCC-512. Cables are supplied in a standard length of 4 m (12'). For more information on QD cables, see page 368 and the Accessories section. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 345 VALU-BEAM(R) 915 Series Sensors 915 Series Dimensions 915 Series Opposed, Retro, and Diffuse Sensing Modes (model suffix E, ESR, R, RSR, LV, D & DSR) 915 Series Sensor with Attached Cable 915 Series Sensor with Quick-Disconnect LED Indicator 36.6 mm (1.44") 35.6 mm (1.40") Lens Centerline 50.8 mm (2.00") 39.1 mm (1.54") 12.7 mm (0.50") 26.7 mm (1.05") M30 x 1.5 External Thread 1/2" - 14 NPSM Internal Thread Hex Nut Supplied Mini-style Quick-disconnect 915 Series Sensor - Convergent Sensing Mode (model suffix LVAG & CV) 915 Series Sensor - Glass Fiber Optic (model suffix F) 39.6 mm (1.56") 42.2 mm (1.66") Fiber Port Centerline 915 Series Sensor - Plastic Fiber Optic (model suffix FP) 42.2 mm (1.66") 915 Series Sensor - Rear View Sensitivity Control (Turn CW to Increase) Fiber Port Centerline 17.8 mm (0.70") 5.6 mm (0.22") 4.5 mm (#10) Screw Clearance (2) 25.4 mm (1.00") 346 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 915 Series Sensors NOTES: Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 347 VALU-BEAM(R) 990 Series Sensors VALU-BEAM 990 Series Sensors With Built-In Totalizing Counter VALU-BEAM 990 Series quick-disconnect and cabled models shown * Each sensor is an economical, one-piece photoelectric counting system * Simple, 2-wire hookup to universal voltage: 12 to 115V dc or 10 to 250V ac * Six-digit totalizer is reset upon power-up, or by touching the top of the sensor with a permanent magnet * Models are available with memory backup to "hold" count for up to 100 hours with power removed (order model suffix "MB") * Specially-designed infrared retroreflective version is available for counting people passing through entryways 990 Series Sensing Mode Options Opposed Retroreflective Convergent Glass and Plastic Fiber Optic Infrared, 880 nm 990 Series Opposed Mode Emitter (E) and Receiver (R) Models Range Supply Voltage Cable Output Type Excess Gain Beam Pattern Effective Beam: 12.7 mm 1000 SMA91E SMA99R SMA91EQD SMA99RQD 60 m (200') 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 3-Pin Mini QD Emitter: 10-250V ac/dc Receiver: 10-250V ac or 12-115V dc Built-in 6-digit totalizing counter E X C E S S G A I N SMA91E & SMA99R 10 SMA91E / SMA99R 1500 mm 100 40.0 in 500 mm 20.0 in 0 Opposed Mode 0 500 mm 20.0 in 1000 mm 40.0 in 1500 mm 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft 100 m 330 ft 60.0 in 0 15 m 50 ft 30 m 100 ft DISTANCE SMA91ESR SMA99RSR SMA91ESRQD SMA99RSRQD 3m (10') 2 m (6.5') 2 m (6.5') 3-Pin Mini QD 3-Pin Mini QD Emitter: 10-250V ac/dc Receiver: 10-250V ac or 12-115V dc Built-in 6-digit totalizing counter 60 m 200 ft SMA91ESR & SMA91RSR 300 mm 100 Opposed Mode 12.0 in Opposed Mode 200 mm 8.0 in 100 mm 4.0 in 0 G A I N 10 1 .01 m .033 ft .10 m .33 ft 75 m 250ft Effective Beam: 3.5 mm SMA91ESR & SMA99RSR 1.0 m 3.3 ft DISTANCE 348 45 m 150 ft DISTANCE 1000 E X C E S S 60.0 in Opposed Mode 1000 mm 10 m 33 ft 0 100 mm 4.0 in 200 mm 8.0 in 300 mm 12.0 in 0 .6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10ft DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 990 Series Sensors P Visible red 650 nm and Infrared 940 nm Non-Polarized Polarized NOTE: Retroreflective range is specified using one model BRT-3 retroreflector (3-inch diameter). Actual sensing range may be more or less than specified, depending upon the efficiency and reflective area of the retroreflector(s) in use. See page 722 for more information. 990 Series Retroreflective Mode Models Range Cable Supply Voltage Output Type Non-Polarized (Visible red, 650 nm) SMA990LV SMA990LVQD 0.15 - 9 m (6" - 30') 2 m (6.5') 3-Pin Mini QD 10-250V ac or 12-115V dc Excess Gain Beam Pattern 1000 Built-in 6-digit totalizing counter E X C E S S SMA990LV 100 SMA990LV 150 mm Retroreflective Mode with BRT-3 reflector 4.0 in 50 mm 2.0 in 0 G A I N 10 0 50 mm 2.0 in 100 mm 150 mm 1 .01 m .033 ft Non-Polarized (Infrared, 940 nm)* 9m (30') 2 m (6.5') 3-Pin Mini QD 10-250V ac or 12-115V dc .10 m .33 ft 1.0 m 3.3 ft 6.0 in 0 10 m 33 ft 2m 6.6 ft 4m 13 ft 2 m (6.5') 3-Pin Mini QD 10-250V ac or 12-115V dc 8m 26 ft 10 m 33 ft 1000 Built-in 6-digit totalizing counter E X C E S S SMA990LT 100 SMA990LT 150 mm Retroreflective Mode with BRT-3 reflector 6.0 in Retroreflective Mode 100 mm 4.0 in 50 mm 2.0 in 0 G A I N 10 0 50 mm 2.0 in With BRT-3 Reflector 100 mm 4.0 in 150 mm 1 .01 m .033 ft Polarized (Visible red, 650 nm) 0.3 - 4.5 m (1 - 15') 6m 20 ft DISTANCE .10 m .33 ft 1.0 m 3.3 ft 6.0 in 0 10 m 33 ft 1.8 m 6 ft 3.6 m 12 ft 5.4 m 18 ft 7.2 m 24 ft 9m 30 ft DISTANCE DISTANCE SMA990LVAG SMA990LVAGQD 4.0 in With BRT-3 Reflector DISTANCE SMA990LT SMA990LTQD 6.0 in Retroreflective Mode 100 mm 1000 Built-in 6-digit totalizing counter E X C E S S SMA990LVAG 100 SMA990LVAG 75 mm Retroreflective Mode with BRT-3 reflector 3.0 in Retroreflective Mode 50 mm 2.0 in 25 mm 1.0 in 0 G A I N 10 0 25 mm With BRT-3 Reflector 50 mm 2.0 in 75 mm 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft 10 m 33 ft DISTANCE 1.0 in 3.0 in 0 1m 3.3 ft 2m 6.6 ft 3m 10 ft 4m 13 ft 5m 16 ft DISTANCE * Note: "LT" models include 0.1 second delays to minimize multiple counts in "people counting" applications. Use polarized models when shiny objects will be counted. For VALU-BEAM 990 Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SMA990LV W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 349 VALU-BEAM(R) 990 Series Sensors Visible red 650 nm 990 Series Convergent Mode Models Focus Supply Voltage Cable Excess Gain Output Type Beam Pattern Performance based on 90% reflectance white test card 1000 SMA990CV 38 mm (1.5") SMA990CV SMA990CVQD Spot Size at Focus: 1.5 mm (0.06") 2 m (6.5') 3-Pin Mini QD 10-250V ac or 12-115V dc Built-in 6-digit totalizing counter E X C E S S Convergent Mode 100 SMA990CV 2.4 mm 0.09 in Convergent Mode 1.6 mm 0.06 in 0.8 mm 0.03 in 0 G A I N 10 1 1 mm .04 in 10 mm .4 in 100 mm 4 in 0 0.8 mm 0.03 in 1.6 mm 0.06 in 2.4 mm 0.09 in 0 1000 mm 40 in 12.5 mm 25 mm 37.5 mm 50 mm 62.5 mm 0.50 in 1.0 in 1.5 in 2.0 in 2.5 in DISTANCE DISTANCE Infrared, 880 nm 990 Series Glass Fiber Optic Models Range Supply Voltage Cable Output Type Excess Gain Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 SMA990F E X C E S S SMA990F SMA990FQD Range varies by sensing mode and fiber optics used G A I N 2 m (6.5') 3-Pin Mini QD 10-250V ac or 12-115V dc IT23S Fibers 3 in Opposed Mode 50 mm 2 in 25 mm IT13S Fibers Opposed Mode Glass Fibers 10 mm .4 in 1 in 0 10 1 1 mm .04 in Built-in 6-digit totalizing counter SMA990F 75 mm 100 IT13S IT23S 1 in 50 mm 2 in 75 mm 100 mm 4 in 0 25 mm 3 in 0 1000 mm 40 in 100 mm 200 mm 300 mm 400 mm 500 mm 4 in 8 in 12 in 16 in 20 in DISTANCE DISTANCE 1000 E X C E S S G A I N SMA990F 1.9 mm 100 Diffuse Mode Glass Fibers 0.050 in Diffuse Mode 0.65 mm 0 BT23S Fiber 10 BT13S Fiber 1 1 mm .04 in 0.075 in SMA990F 1.3 mm BT13S BT23S 100 mm 4 in DISTANCE 1000 mm 40 in 0 0.65 mm 0.025 in 1.3 mm 0.050 in 1.9 mm 10 mm .4 in 0.025 in 0.075 in 0 7.5 mm 0.3 in 15 mm 22.5 mm 30 mm 37.5 mm 0.6 in 0.9 in 1.2 in 1.5 in DISTANCE For VALU-BEAM 990 Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SMA990CV W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. 350 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 990 Series Sensors Visible red, 650 nm 990 Series Plastic Fiber Optic Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 SM990FP E X C E S S Opposed Mode Plastic Fibers SMA990FP SMA990FPQD Range varies by sensing mode and fiber optics used 2 m (6.5') 3-Pin Mini QD 10-250V ac or 12-115V dc 10 PIT26U Fiber 1 1 mm .04 in Built-in 6-digit totalizing counter 10 mm .40 in 100 mm 4.0 in 1.8 in Opposed Mode 30 mm 1.2 in 15 mm 0.6 in 0 PIT46U Fiber G A I N SMA990FP 45 mm 100 PIT46U PIT26U 0 15 mm 0.6 in 30 mm 1.2 in 45 mm 1.8 in 0 1000 mm 40 in 25 mm 1 in 50 mm 2 in 75 mm 100 mm 125 mm 3 in 4 in 5 in DISTANCE DISTANCE 1000 E X C E S S SMA990FP 100 SMA990FP Diffuse Mode Plastic Fibers 3.8 mm 0.10 in 1.2 mm 0.05 in 0 G A I N 0.15 in Diffuse Mode 2.5 mm PBT46U Fiber 10 PBT26U Fiber 1 .1 mm .004 in 1 mm .04 in 10 mm .4 in DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 PBT26U PBT46U 0.05 in 2.5 mm 0.10 in 3.8 mm 100 mm 4 in 0 1.2 mm 0.15 in 0 7.5 mm 0.3 in 15 mm 22.5 mm 30 mm 37.5 mm 0.6 in 0.9 in 1.2 in 1.5 in DISTANCE 351 VALU-BEAM(R) 990 Series Sensors 990 Series Specifications Supply Voltage and Current 990 Series sensors wire directly to either 10 to 250V ac (50/60 Hz) or 12 to 115V dc at less than 20 milliamps Supply Protection Circuitry Protected against transient voltages Sensor Response Time 15 milliseconds LIGHT; 15 milliseconds DARK (except model SMA990LT); independent of signal strength NOTE: 100 millisecond delay on power up (no counts are entered during this time) Count Entry Counts are entered on DARK-to-LIGHT transition Count Reset In standard models, counter is reset to zero automatically upon applying power to the sensor. All models may be reset by touching the housing on top of the sensor with permanent magnet (supplied with sensor) Indicators Top-mounted red LED indicator lights whenever the sensor sees "light" condition. Models SMA91E and SMA91ESR emitters have visible-red "tracer beam" which indicates "power on" and enables easy "line-of-sight" alignment. Construction Reinforced thermoplastic polyester housing, totally encapsulated, o-ring sealed lenses or fiber fittings, stainless steel hardware Environmental Rating Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 12 and 13; IEC IP66 Connections PVC-jacketed 2-conductor 2 m (6.5') or 9 m (30') cables or 3-pin mini-style quick-disconnect (QD) fitting are available. QD cables are ordered separately. See page 368 and Accessories section. Operating Conditions Temperature: 0 to 50C (32 to 122F) Maximum relative humidity: 90% at 50C (non-condensing) Application Notes Models with memory backup have no power-up delay. Some models with memory backup may increment 1 count upon reapplication of power Certifications Note: 990 Series sensors with internal memory backup (MB) for maintaining "count memory" are available by special order by adding the suffix "MB" to the model number (eg.- SMA990LVMB). 352 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 990 Series Sensors 990 Series Hookup Diagrams Sensors with Attached Cable bn bu + - Sensors with Quick-Disconnect 3-Pin Mini-Style bn 10-250V ac or 12 to 115V dc bu bu 10-250V ac - or 12 to 115V dc bk Emitters with Attached Cable bn + Emitters with Quick-Disconnect 3-Pin Mini-Style bn + bu 10-250V ac/dc - + 10-250V ac/dc - bk 3-Pin Mini-Style Pin-out (Cable Connector Shown) Black Wire Blue Wire Brown Wire Quick-Disconnect (QD) Option 990 Series VALU-BEAM sensors are sold with either a 2 m (6.5') or a 9 m (30') attached PVC-covered cable, or with a 3-pin ministyle QD cable fitting. QD sensors are identified by the letters "QD" in their model number suffix. Mating cables for QD 990 Series sensors are model MBCC-312. Cables are supplied in a standard length of 4 m (12'). For more information on QD cables, see page 368 and the Accessories section. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 353 VALU-BEAM(R) 990 Series Sensors 990 Series Dimensions 990 Series Opposed, Retro, and Diffuse Sensing Modes (model suffix E, ESR, R, RSR, LV & LT) 990 Series Sensor with Attached Cable 990 Series Sensor with Quick-Disconnect Reset Counter to Zero by Touching With a Magnet Here 36.6 mm (1.44") 49.8 mm (1.96") Lens Centerline 50.8 mm (2.00") 39.1 mm (1.54") 17.8 mm (0.70") 12.7 mm (0.50") 5.6 mm (0.22") Hex Nut Supplied M30 x 1.5 External Thread 1/2" - 14 NPSM"ternal Thread 26.7 mm (1.05") Mini-style Quick-disconnect 25.4 mm (1.00") 990 Series Sensor - Convergent Sensing Mode (model suffix LVAG & CV) 990 Series Sensor - Glass Fiber Optic (model suffix F) 53.8 mm (2.12") 56.4 mm (2.22") Fiber Port Centerline 990 Series Sensor - Plastic Fiber Optic (model suffix FP) 990 Series Sensor - Rear View LED Indicator 56.4 mm (2.22") Fiber Port Centerline 4.5 mm (#10) Screw Clearance (2) External Thread M30 x 1.5 354 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) 990 Series Sensors NOTES: Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 355 VALU-BEAM(R) SMI912 Series Sensors VALU-BEAM SMI912 Series Sensors SMI912 Series sensor, with CI3RC2 current amplifier module (left) and intrinsic safety barrier (right) * Intrinsically safe sensors with the performance of VALU-BEAM Sensors * Use with approved intrinsic safety barriers and model CI3RC2 current trip point amplifier (see hookup diagram on page 361) * Certified for use in all Classes, Groups and Divisions of hazardous locations as defined by Article 500 of the National Electrical Code when used with approved I.S. barriers * All models have rear panel sensitivity control and light/dark operate switch, plus Banner's exclusive Alignment Indicating Device system (AIDTM) * 3-pin mini-style quick-disconnect (QD) connector is standard on all models; mating cables are ordered separately U.S. Patent #4356393 SMI912 Series Sensing Mode Options Opposed Retroreflective Diffuse Convergent Glass and Plastic Fiber Optic Infrared, 880 nm SMI912 Series Opposed Mode Emitter (E) and Receiver (R) Models Range Supply Voltage Cable Output Type Excess Gain Beam Pattern Effective Beam: 13 mm 1000 SMI91EQD SMI91RQD 60 m (200') 3-Pin Mini QD 10-30V dc Receiver: NPN E X C E S S G A I N 100 10 1500 mm SMI91EQD & SMI91RQD 60.0 in 1000 mm Opposed Mode 40.0 in 20.0 in 500 mm SMI91EQD & SMI91RQD 0 0 Opposed Mode 500 mm 20.0 in 1000 mm 40.0 in 60.0 in 1500 mm 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft 0 100 m 330 ft 15 m 50 ft DISTANCE SMI91ESRQD SMI91RSRQD 3m (10') 3-Pin Mini QD 10-30V dc Receiver: NPN 60 m 200 ft SMI91ESRQD & SMI91RSRQD 300 mm 100 12.0 in Opposed Mode 200 mm 8.0 in 100 mm 4.0 in 0 G A I N 75 m 250ft Effective Beam: 3.5 mm 10 SMI91ESRQD & SMI91RSRQD 1 .01 m .033 ft 0 100 mm 4.0 in 200 mm 8.0 in 300 mm 12.0 in Opposed Mode .10 m .33 ft 1.0 m 3.3 ft DISTANCE 356 45 m 150 ft DISTANCE 1000 E X C E S S 30 m 100 ft 10 m 33 ft 0 .6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10ft DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) SMI912 Series Sensors NOTE: Use polarized model when shiny objects will be sensed. Retroreflective range is specified using one model BRT-3 retroreflector (3" diameter). Actual sensing range may be more or less than specified, depending upon the efficiency and reflective area of the retroreflector(s) in use. See page 722 for more information. P Visible red, 650 nm Non-Polarized Polarized SMI912 Series Retroreflective Mode Models Range Cable Supply Voltage Output Type Excess Gain 1000 Non-Polarized SMI912LVQD 0.15 - 9 m (6" - 30') 3-Pin Mini QD Beam Pattern E X C E S S 10-30V dc SMI912LVQD Retroreflective Mode With BRT-3 Reflector NPN 6.0 in Retroreflective Mode 100 mm 4.0 in 50 mm 2.0 in 0 10 G A I N SMI912LVQD 150 mm 100 0 50 mm 2.0 in 100 mm 4.0 in With BRT-3 Reflector 150 mm 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft 10 m 33 ft 6.0 in 0 2m 6.6 ft 4m 13 ft DISTANCE 6m 20 ft 8m 26 ft 10 m 33 ft DISTANCE 1000 Polarized E X C E S S SMI912LVAGQD Retroreflective Mode SMI912LVAGQD 75 mm 100 W/BRT-3 Reflector 3.0 in Retroreflective Mode 50 mm 2.0 in 25 mm 1.0 in 0 SMI912LVAGQD 0.3 - 4.5 m (1 - 15') 3-Pin Mini QD 10-30V dc 10 G A I N NPN 0 25 mm 1.0 in With BRT-3 Reflector 50 mm 2.0 in 75 mm 1 .01 m .033 ft .10 m .33 ft 1.0 m 3.3 ft 3.0 in 0 10 m 33 ft 1m 3.5 ft 2m 6.6 ft 3m 10 ft 4m 13 ft 5m 16 ft DISTANCE DISTANCE Infrared 880 nm SMI912 Series Diffuse Mode Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Performance based on 90% reflectance white test card 1000 SMI912DSRQD SMI912DSRQD 390 mm (15") E X C E S S 3-Pin Mini QD 10-30V dc NPN Diffuse Mode SMI912DSRQD 18 mm 0.75 in Diffuse Mode 100 12 mm 0.50 in 6 mm 0.25 in 0 G A I N 10 1 1 mm .04 in 10 mm .4 in 100 mm 4 in 0 6 mm 0.25 in 12 mm 0.50 in 18 mm 0.75 in 0 1000 mm 40 in 75 mm 150 mm 225 mm 300 mm 375 mm 3 in 6 in 9 in 12 in 15 in DISTANCE DISTANCE 1000 SMI912DQD SMI912DQD 780 mm (30") E X C E S S 3-Pin Mini QD 10-30V dc NPN Diffuse Mode SMI912DQD 18 mm 100 0.75 in Diffuse Mode 12 mm 0.50 in 6 mm 0.25 in 0 G A I N 10 0 6 mm 0.25 in 12 mm 0.50 in 18 mm 1 1 mm .04 in 10 mm .4 in 100 mm 4 in DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 1000 mm 40 in 0.75 in 0 150 mm 300 mm 450 mm 600 mm 750 mm 6 in 12 in 18 in 24 in 30 in DISTANCE 357 VALU-BEAM(R) SMI912 Series Sensors Visible red 650 nm SMI912 Series Convergent Mode Models Focus Supply Voltage Cable Output Type Excess Gain Beam Pattern Performance based on 90% reflectance white test card 1000 SMI912CVQD E X C E S S 38 mm (1.5") SMI912CVQD Spot Size at Focus: 1.5 mm (0.06")) 3-Pin Mini QD 10-30V dc NPN Convergent Mode SMI912CVQD 2.4 mm 100 0.09 in Convergent Mode 1.6 mm 0.06 in 0.8 mm 0.03 in 0 G A I N 10 0 0.8 mm 0.03 in 1.6 mm 0.06 in 2.4 mm 1 1 mm .04 in 10 mm .4 in 100 mm 4 in 0.09 in 0 1000 mm 40 in 15 mm 0.60 in 30 mm 1.2 in 45 mm 1.8 in 60 mm 2.4 in 75 mm 3.0 in DISTANCE DISTANCE Infrared, 880 nm SMI912 Series Glass Fiber Optic Emitter (E) and Receiver (R) Models Range Supply Voltage Cable Output Type Excess Gain Beam Pattern 1000 E X C E S S SMI91EFQD & SMI91RFQD Opposed Mode 100 SMI91EFQD & SMI91RFQD 75 mm IT23S Fibers 2 in Opposed Mode 25 mm 0 SMI91EFQD SMI91RFQD Range varies with fiber optics used G A I N 10 IT13S Fibers 10-30V dc IT13S 1 in IT23S 10 mm .4 in 100 mm 4 in 1 in 50 mm 2 in 3 in 0 1000 mm 40 in 100 mm 200 mm 300 mm 400 mm 500 mm 4 in 8 in 12 in 16 in 20 in DISTANCE DISTANCE NPN 0 25 mm 75 mm 1 1 mm .04 in 3-Pin Mini QD 3 in 50 mm 1000 E X C E S S G A I N SMI91EFQD & SMI91RFQD Opposed Mode Glass Fiber 100 SMI91EFQD & SMI91RFQD 300 mm 12.0 in Opposed Mode 200 mm IT23S Fibers w/L16F lenses 10 8.0 in 100 mm 0 100 mm 1 0.1 m 0.33 ft 1.0 m 3.3 ft 0 IT23S Fibers With L16F lenses 200 mm IT23S Fibers w/L9 lenses 4.0 in IT23S Fibers With L9 lenses 300 mm 10 m 33 ft DISTANCE 100 m 330 ft 4.0 in 8.0 in 12.0 in 0 2.4 m 8 ft 4.8 m 16 ft 7.2 m 24 ft 9.6 m 32 ft 12 m 40 ft DISTANCE For VALU-BEAM SMI912 Series Sensors: i) All models require a mating cable. See page 368 for more information. 358 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) SMI912 Series Sensors Infrared, 880 nm SMI912 Series Glass Fiber Optic Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 SMI912FQD E X C E S S Opposed Mode 100 IT23S Fibers SMI912FQD 75 mm 2 in 25 mm 1 in 0 SMI912FQD Range varies by sensing mode and fiber optics used G A I N 3 in Opposed Mode 50 mm 10 IT13S Fibers 1 1 mm .04 in 10 mm .4 in 100 mm 4 in IT13S IT23S 1 in 50 mm 2 in 75 mm 3 in 0 1000 mm 40 in 100 mm 200 mm 300 mm 400 mm 500 mm 4 in 8 in 12 in 16 in 20 in DISTANCE DISTANCE 3-Pin Mini QD 10-30V dc 0 25 mm NPN 1000 SMI912FQD E X C E S S G A I N Diffuse Mode 1.9 mm 100 0.075 in SMI912FQD 1.3 mm 0.050 in Diffuse Mode 0.65 mm BT13S Fiber 1 1 mm .04 in 0.025 in 0 BT23S Fiber 10 BT13S 0 BT23S 0.65 mm 0.025 in 1.3 mm 0.050 in 1.9 mm 10 mm .4 in 100 mm 4 in 0.075 in 0 1000 mm 40 in 7.5 mm 0.3 in 15 mm 22.5 mm 30 mm 37.5 mm 0.6 in 0.9 in 1.2 in 1.5 in DISTANCE DISTANCE Visible red, 650 nm SMI912 Series Plastic Fiber Optic Models Range Cable Supply Voltage Output Type Excess Gain Beam Pattern Diffuse mode performance based on 90% reflectance white test card 1000 E X C E S S SMI912FPQD Range varies by sensing mode and fiber optics used G A I N SMI912FPQD Opposed Mode Plastic Fibers 100 45 mm 0.6 in 0 10 PIT26U Fibers PIT26U PIT46U 0.6 in 30 mm 0.12 in 45 mm 10 mm 0.4 in 100 mm 4.0 in NPN 0 15 mm 1000 mm 40 in 0.18 in 0 25 mm 1 in 50 mm 2 in DISTANCE 10-30V dc 0.12 in Opposed Mode 15 mm PIT46U Fibers 1 0.1 mm 0.04 in 3-Pin Mini QD 0.18 in SMI912FPQD 30 mm 75 mm 100 mm 125 mm 3 in 4 in 5 in DISTANCE 1000 E X C E S S SMI912FPQD SMI912FPQD Diffuse Mode Plastic Fibers 100 3.6 mm 0.10 in 1.2 mm 0.05 in 0 G A I N 0.15 in Diffuse Mode 2.4 mm PBT46U Fibers 10 PBT26U Fibers 1 0.01 mm 0.004 in 1.0 mm 0.04 in 10 mm 0.4 in DISTANCE Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 PBT26U PBT46U 0.05 in 2.4 mm 0.10 in 3.6 mm 100 mm 4 in 0 1.2 mm 0.15 in 0 7.5 mm 0.3 in 15 mm 22.5 mm 30 mm 37.5 mm 0.6 in 0.9 in 1.2 in 1.8 in DISTANCE 359 VALU-BEAM(R) SMI912 Series Sensors SMI912 Series Specifications Supply Voltage and Current 10 to 30V dc for sensor, 25 mA maximum Division 1 use, with barriers, requires a minimum system supply voltage of 10V Output Configuration Current sinking NPN open collector transistor Output Rating 3-wire hookup sinks 15 mA maximum, continuous 2-wire hookup sinks 10 mA (OFF-state) and 20 mA (ON state) Output Protection Circuitry Protected against false pulse on power-up and short circuit of output Output Response Time 4 milliseconds ON and OFF, except for opposed mode receivers, which are 8 ms ON, 4 ms OFF; independent signal strength (NOTE: 100 millisecond delay on power-up: output is non-conducting during this time) Repeatability Opposed: 1.0 millisecond; Retro, Diffuse, Convergent, Plastic and Glass Fiber Optic: 1.3 milliseconds Adjustments LIGHT/DARK OPERATE select switch on rear of sensor Sensitivity control on rear of sensor allows precise gain setting (turn clockwise to increase gain) Indicators Exclusive, patented Alignment Indicating Device (AIDTM, US patent #4356393) lights at top mounted red LED indicator whenever the sensor sees a "light" condition, with a superimposed pulse rate proportional to the light signal strength (the stronger the signal, the faster the pulse rate). Construction Reinforced thermoplastic polyester housing, totally encapsulated, molded acrylic lenses, stainless steel hardware Environmental Rating Meets NEMA standards 1, 2, 3, 3S, 4, 4X, 12 and 13; IEC IP66 Connections Supplied with 3-pin quick-disconnect (QD) fitting and requires the use of mating cable model SMICC-312. Cable is not supplied with sensors. See page 368 and Accessories section. Operating Conditions Temperature: Relative relative humidity: Certifications -20 to +70C (-4 to +158F) 90% at 50C (non-condensing) Exia APPROVALS 360 CSA: #LR 41887 Instrinsically Safe, with Entity for: Class I, Groups A-D Class I, Div. 2, Groups A-D FM: #J.I. OR3HO.AX Intrinsically Safe, with Entity for: Class I, II, III, Div. 1, Groups A-G Class I, II, III, Div. 2, Groups A-D and G KEMA: #Ex-96.D.0950 EEx ia IIC T6 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) SMI912 Series Sensors SMI912 Series Hookup Diagrams Opposed Mode Emitter and Receiver Hookup Non-Hazardous Area Hazardous Area 1 Dual Barrier In + 105 to 130V ac AC Supply 4 5 6 7 8 Relay Output 5 Amp Contacts CI3RC2 210 to 250V ac 9 10 11 1 2 3 Input: 10mA (OFF State) 20mA (ON State) + Out I.S.- - Aux. Input Common In + Opto-Coupler Output: 20mA max. SMI Series Emitter Brown 2 3 SMI91EQD SMI91ESRQD SMI91EFQD Blue + Out Black 1 SMI Series Receiver Brown Busbar Blue Emitter Models: G 2 3 Receiver Models: SMI91RQD SMI91RSRQD SMI91RFQD Bottom View of Cable Connector on Sensor (colors shown are for mating cable model SMICC-312) Earth Ground (less than 1) SMI912 Series Retro, Diffuse, Convergent, Glass and Plastic Fiber Optic Hookup Non-Hazardous Area Hazardous Area Black 1 In + AC Supply 105 to 130V ac 210 to 250V ac 4 5 6 7 8 Relay Output 5 Amp Contacts CI3RC2 9 10 11 1 2 3 Input: 10mA (OFF State) 20mA (ON State) + Out I.S. - - Aux. Input Common I.S. Barrier Opto-Coupler Output: 20mA max. Busbar SMI Series Emitter Brown 2 3 Banner SMI912 Series Blue Bottom View of Cable Connector on Sensor (colors shown are for mating cable model SMICC-312) G Earth Ground (less than 1) Intrinsic Safety Kits for Use with SMI912 Intrinsically Safe Sensors Model Description CI2BK-1 Kit includes a CI3RC2 current amplifier, one RS-11 socket, one DINrail mount, and one single-channel intrinsically safe barrier (barriers also sold separately - see below) CI2BK-2 Typically used in Opposed Mode setups, this kit includes a CI3RC2 current amplifier, one RS-11 socket, one DIN-rail mount, and dual-channel intrinsically safe barrier (barriers also sold separately - see below) CIB-1 Single-channel barrier CI2B-1 Dual-channel barrier Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 361 VALU-BEAM(R) SMI912 Series Sensors SMI912 Series Dimensions SMI912 Series Opposed, Retro, and Diffuse Sensing Modes (model suffix E, ESR, R, RSR, LV, D & DSR) SMI912 Series Sensor - Convergent Mode (model suffix LVAG & CV) 39.6 mm (1.56") M30 x 1.5 Thread Hex Nut Supplied 26.7 mm (1.05") Mini-style Quick-disconnect SMI912 Series Sensor - Plastic Fiber Optic Mode (model suffix FP) SMI912 Series Sensor - Glass Fiber Optic Mode (model suffix F, EF & RF) 42.2 mm (1.66") 42.2 mm (1.66") Fiber Port Centerline Fiber Port Centerline SMI912 Series Sensor - Rear View Light/Dark Operate (L.O. = CW, D.O. = CCW) Remove Screws to Access Controls Sensitivity Control (Turn CW to Increase) 17.8 mm (0.70") 4.5mm (#10) Screw Clearance (2) 5.6 mm (0.22") 25.4 mm (1.00") 362 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) SMI912 Series Sensors NOTES: Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 363 VALU-BEAM(R) SM91EN/RN Series Sensors SM91EN/RN Series Sensors Enhanced Sunlight Immunity VALU-BEAM SM91EN/RN Series quick-disconnect and cabled models shown * Opposed mode sensing to 30 m (100') with enhanced sunlight immunity for difficult outdoor applications, or for indoor applications where there is intense light * Choice of three modulation codes to allow adjacent sensor pairs to operate without crosstalk * 10 to 30V dc operation; receivers have bipolar solid-state outputs: one NPN (sinking) and one PNP (sourcing) * Circuitry is totally encapsulated in a rugged, molded thermoplastic polyester housing; rated IP67, NEMA 6P * Exceptional EMI-RFI immunity SM91EN/RN Series Sensing Mode Options Opposed Infrared, 880 nm SM91EN Opposed Mode Emitter (E) and SM91RN Receiver (R) - Modulation Code A Models Range Supply Voltage Cable Output Type Beam Pattern Excess Gain Effective Beam: 25 mm 1000 SM91EAN SM91EANQD SM91RAN SM91RANQD 30 m (100') 2 m (6.5') 3-Pin Mini QD 2 m (6.5') 4-Pin Mini QD 10-30V dc Bipolar NPN/PNP E X C E S S SM91EN/RN Opposed Mode 12.0 in Opposed Mode 200 mm 8.0 in 100 mm 4.0 in 0 G A I N 0 10 100 mm 4.0 in 200 mm 8.0 in 300 mm 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft DISTANCE SM91EN/RN 300 mm 100 100 m 330 ft 12.0 in 0 0.6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10 ft DISTANCE Note: Beam Pattern response shown from 0 to 3 m (Excess Gain = 100x at 3 m) For VALU-BEAM SM91EN/RN Series Sensors: i) 9 m (30') cables are available by adding suffix "W/30" to the model number of any cabled sensor (e.g. - SM91EAN W/30) ii) A model with a QD connector requires an accessory mating cable. See pages 368 and the Accessories section for more information. 364 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) SM91EN/RN Series Sensors SM91EN Opposed Mode Emitter (E) and SM91RN Receiver (R) - Modulation Code B Models Range Cable Supply Voltage Output Type Beam Pattern Excess Gain Effective Beam: 25 mm 1000 SM91EBN SM91EBNQD SM91RBN SM91RBNQD 30 m (100') 2 m (6.5') 3-Pin Mini QD 2 m (6.5') 4-Pin Mini QD 10-30V dc Bipolar NPN/PNP E X C E S S SM91EN/RN Opposed Mode SM91EN/RN 300 mm 100 12.0 in Opposed Mode 200 mm 8.0 in 100 mm 4.0 in 0 G A I N 10 0 100 mm 4.0 in 200 mm 8.0 in 300 mm 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft 12.0 in 0 100 m 330 ft 0.6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10 ft DISTANCE DISTANCE SM91EN Opposed Mode Emitter (E) and SM91RN Receiver (R) - Modulation Code C Models Range Cable Supply Voltage Output Type Beam Pattern Excess Gain Effective Beam: 25 mm 1000 SM91ECN SM91ECNQD SM91RCN SM91RCNQD 30 m (100') 2 m (6.5') 3-Pin Mini QD 2 m (6.5') 4-Pin Mini QD 10-30V dc Bipolar NPN/PNP E X C E S S SM91EN/RN Opposed Mode 12.0 in Opposed Mode 200 mm 8.0 in 100 mm 4.0 in 0 G A I N 0 10 100 mm 4.0 in 200 mm 8.0 in 300 mm 1 0.1 m 0.33 ft 1.0 m 3.3 ft 10 m 33 ft DISTANCE SM91EN/RN 300 mm 100 100 m 330 ft 12.0 in 0 0.6 m 2 ft 1.2 m 4 ft 1.8 m 6 ft 2.4 m 8 ft 3.0 m 10 ft DISTANCE Note: Beam Pattern response shown from 0 to 3 m (Excess Gain = 100x at 3 m) Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 365 VALU-BEAM(R) SM91EN/RN Series Sensors SM91EN/RN Series Specifications Supply Voltage and Current 10 to 30V dc at 20 mA maximum for receivers (exclusive of load current) and 25 mA maximum for emitters Output Configuration Bipolar: one current sourcing (PNP) and one current sinking (NPN) open-collector transistor Output Response Time 12 to 28 milliseconds, depending upon code LIGHT operate only Output Rating 150 mA maximum (continuous, each output) Off-state leakage current is 100 microamps, maximum On-state saturation voltage less than 1V at 10 mA and less than 2 V at 150 mA (PNP); less than 200 millivolts at 10 mA and less than 1V at 150 mA (NPN) Indicators Top-mounted LED indicator - a red LED (on receivers) lights when the output is conducting and pulses at a rate proportional to the strength of the received light signal; a green LED (on emitters) lights when the infrared sensing beam is "ON" Construction Reinforced black thermoplastic polyester housing, totally epoxy-encapsulated, replaceable acrylic lenses Environmental Rating Meets NEMA 6P and IEC IP67 standards Connections PVC-jacketed 2 m (6.5') or 9 m (30') cables or integral mini-style quick-disconnect (QD) fitting are available Operating Conditions Temperature: 0 to 70C (+32 to 158F) Maximum relative humidity: 90% at 50C (non-condensing) Water Immersion Sensors will continue to operate during and after being submerged in water at a depth of 2 m (6') for a period of 48 hours NOTE: Immersion greatly reduces the efficiency of the lens, which results in greatly diminished sensing range Sunlight Immunity Receivers may be pointed into a light source of 120,000 lux without false-triggering, and will still respond only to the infrared beam from their modulated emitters. Receivers will not respond to sunlight reflected from water spray droplets. Strobe Light Immunity Receivers are totally immune to one Federal Signal Corp. "Fireball" model FB2PST strobe EMI-RFI Immunity Emitters and receivers will not respond to transmissions from a 5-watt output walkie-talkie on the test frequencies of 464.500 and 151.625 megahertz when the walkie-talkie's antenna is held 6" or more away from the sensor. Certifications 366 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) SM91EN/RN Series Sensors SM91EN/RN Series Hookup Diagrams Sensors with Attached Cable bn bk bu + 10-30V dc - bu Load wh Load bk Emitters with Attached Cable bn bn + 10-30V dc - bu wh Sensors with Quick-Disconnect Load Load Emitters with Quick-Disconnect bn + bu 10-250V ac/dc - + 10-250V ac/dc - bk 3-Pin Mini-Style Pin-out 4-Pin Mini-Style Pin-out (Cable Connector Shown) (Cable Connector Shown) Black Wire Blue Wire White Wire Brown Wire Brown Wire Black Wire Blue Wire Quick-Disconnect (QD) Option SM91EN/RN Series VALU-BEAM sensors are sold with either a 2 m (6.5') or a 9 m (30') attached PVC-covered cable, or with a mini-style QD cable fitting. SM91EN/RN QD sensors are identified by the letters "QD" in their model number suffix. Mating cable for QD SM91EN sensors is model MBCC-312. Cable for QD SM91RN sensors is MBCC-412. Cables are supplied in a standard length of 4 m (12'). For more information on QD cables, see page 368 and the Accessories section. Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 367 VALU-BEAM(R) SM91EN/RN Series Sensors SM91EN/RN Series Dimensions SM91EN/RN Series Sensor with Quick-Disconnect SM91EN/RN Series Sensor LED Indicator 36.6 mm (1.44") 35.6 mm (1.40") Lens Centerline 50.8 mm (2.00") 39.1 mm (1.54") 12.7 mm (0.50") M30 x 1.5 Thread Hex Nut Supplied 26.7 mm (1.05") Mini-style Quick-disconnect M30 x 1.5 External Thread 1/2" - 14 NPSM Internal Thread Hex Nut Supplied Accessories VALU-BEAM Modifications Model Suffix Modification W/30 9 m (30') cable Example of Model Number Description All VALU-BEAM sensors may be ordered with an integral 9 m (30') cable in place of the standard 2 m (6.5') cable SM912D W/30 Quick-Disconnect (QD) Cables Following is the selection of cables available for VALU-BEAM QD models. See the Accessories section for more cable information. Style Model Length Connector Used with: 3-Pin Mini MBCC-306 MBCC-312 MBCC-330 2 m (6.5') 4 m (12') 9 m (30') Straight Straight Straight All VALU-BEAM emitters 912 Series ac 990 Series 4-Pin Mini MBCC-406 MBCC-412 MBCC-430 2 m (6.5') 4 m (12') 9 m (30') Straight Straight Straight 912 Series dc SM91RN (sunlight immune) 5-Pin Mini MBCC-506 MBCC-512 MBCC-530 2 m (6.5') 4 m (12') 9 m (30') Straight Straight Straight 915 Series 3-Pin Mini SMICC-306 SMICC-312 SMICC-330 2 m (6.5') 4 m (12') 9 m (30') Straight Straight Straight SMI912 Series (intrinsically safe) 368 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 VALU-BEAM(R) Accessories Cabling Accessories Model AC-6 PVC-6 RF1-2NPS Description I.D. 5/16"; O.D. 7/16" I.D. 1/4"; O.D. 3/8" -- 2 m (6.5') armored cable jacket 2 m (6.5') flexible PVC tubing (not for QD models) Compression fitting for attaching armored cable or PVC tubing * Flexible black nylon cable protector HF1-2NPS * Includes a neoprene gland that compresses around the VALU-BEAM cable to provide an additional seal against moisture * Resistant to gasoline, alcohol, oil, grease, solvents and weak acids * Working temperature range of -30 to +100C (-22 to +212F) Replacement Lens Assemblies VALU-BEAM lens assemblies are field-replaceable. In addition, some lenses may be used to convert from one sensing mode to another, or to change the sensing range of a particular sensor. The possible conversions are listed in the table below. Possible Sensing Mode or Range Changes Model Description UC-900AG UC-900C UC-900DSR UC-900F UC-900FP UC-900L UC-900J Replacement lens for LVAG Replacement lens for C and CV Replacement lens for DSR, ESR & RSR Replacement lens for F Replacement lens for FP Replacement lens for E, R, LV & D Attach to VALU-BEAMs E, R, ESR, RSR, LV and D Change LV to LVAG Change LV to CV Change D or F to DSR, EF to ESR and RF to RSR Change D to F and DSR to F - Change LVAG to LV, CV to LV, DSR to D & F to D Flat Lexan(R) dust cover Lexan(R) is a registered trademark of General Electric Co. Extension Cables (without connectors) The following cables are available for extending the length of existing sensor cable. These are 30 m (100') lengths of VALU-BEAM cable. This cable may be spliced to existing cable. Connectors, if used, must be customer-supplied. Model Type Used with: EC312-100 4-conductor SM912 Series dc sensors EC312A-100 2-conductor For all emitters, SM2A912 Series ac sensors and 990 Series sensors EC915-100 5-conductor 915 Series sensors Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164 369 VALU-BEAM(R) Accessories Mounting Brackets Model Description Dimensions 56.0 mm (2.20") SMB30C * 30 mm split clamp bracket * Black reinforced thermoplastic polyester * Includes stainless steel mounting hardware 13 mm (0.5") 63.0 mm (2.48") 31.5 mm (1.24") 13.5 mm (0.53") Nut Plate 2.5 mm (0.10") 45.0 mm (1.77") SMB30MM M5 x 0.8 x 80 mm Screw (2) 25.4 mm (1.00") * 30 mm, 12-gauge, stainless steel bracket with curved mounting slots for versatility and orientation * Clearance for M6 (1/4") hardware o30.1 mm (1.19") 35.1 mm (1.38") 7.1 mm .28 x 90 (2 Slots) o 6.4 mm (0.25" dia.) 57.2 mm (2.25") 25.4 mm (1.00") R 25.4 mm (1.00") 57.2 mm 35.1 mm (2.25") (1.38") 69.9 mm (2.75") SMB30SC * 30 mm swivel bracket * Black reinforced thermoplastic polyester * Includes stainless steel mounting and swivel locking hardware 50.8 mm (2.00") M30 x 1.5 internal thread 12.7 mm (0.50") 58.7 mm (2.31") 30.0 mm (1.18") 66.5 mm (2.62") 29.0 mm (1.14") Retroreflective Targets Banner offers a wide selection of high-quality retroreflective targets. See Accessories section for complete information. 370 Banner Engineering Corp. * Minneapolis, U.S.A. * www.bannerengineering.com * Tel: 763.544.3164