Luckylight
Spec No: W12088A/B Rev No: V.2 Date: Sep/08/2003 Page: 1OF 6
Approved:JoJo Checked:Sun Drawn:Liu
Lucky Light Electronics Co., Ltd. http://www.luckylightled.com
Model No.: KWM-R30881XUAB
3.0*3.0mm (1.2") 8×8 Supe
r
Ambe
r
Dot Matrix LED Displays
Technical Data Sheet
Luckylight
Spec No: W12088A/B Rev No: V.2 Date: Sep/08/2003 Page: 2OF 6
Approved:JoJo Checked:Sun Drawn:Liu
Lucky Light Electronics Co., Ltd. http://www.luckylightled.com
Features:
Descriptions:
Applications:
Device Selection Guide:
Model No. Chip Material Face Color Descriptions
KWM-R30881AUAB
AlGaInP
Black Row Anode
KWM-R30881CUAB Black Row Cathode
1.2inch (31.7mm) Matrix height.
Colors:Super Amber.
Flat package and light weight.
Easy assembly.
High quality and low cost.
High reliable and intensity.
Low power requirement.
The product itself will remain within RoHS compliant version.
The KWM-R30881 series is a large emitting area (3.0*3.0mm ) LED sources
configured in a 64 dots 8*8 matrix array.
These devices are made with white dots and black surface.
Audio equipment.
Instrument panels.
Digitalreadoutdisplay.
Luckylight
Spec No: W12088A/B Rev No: V.2 Date: Sep/08/2003 Page: 3OF 6
Approved:JoJo Checked:Sun Drawn:Liu
Lucky Light Electronics Co., Ltd. http://www.luckylightled.com
Package Dimension:
L u c k y l i g h t
KWM-R30881XXX
KWM-R30881AUAB KWM-R30881CUAB
ROW
1
COL. 1
PIN
2
4
3
5
7
6
1
12
8
14
9
2
7
NO.
13 3 4 10 6
PIN
NO.
2345678
11 15 16
8585
72
67
51
412
38
214
19
87654321COL.
ROW NO.
PIN
13
PIN
NO. 3 6410 11 15 16
NOTES: All dimensions are in millimeters (inches) tolerance are ±0.25mm (0.01inch) unless
otherwise noted.
Luckylight
Spec No: W12088A/B Rev No: V.2 Date: Sep/08/2003 Page: 4OF 6
Approved:JoJo Checked:Sun Drawn:Liu
Lucky Light Electronics Co., Ltd. http://www.luckylightled.com
Absolute Maximum Ratings at Ta=25
Parameters Symbol Max. Unit
Power Dissipation (Per dot) PD 65 mW
Peak Forward Current (Per dot)
(1/10 Duty Cycle, 0.1ms Pulse Width) IFP 100 mA
Forward Current (Per dot) IF 25 mA
Dating Linear From 250.4 mA/
Reverse Voltage VR 5 V
Operating Temperature Range Topr -40to +80
Storage Temperature Range Tstg -40to +85
Soldering Temperature Tsld 260for 5 Seconds
Electrical Optical Characteristics at Ta=25
Parameters Symbol Min. Typ. Max. Unit Test Condition
Luminous Intensity IV 18.0 36.0 --- mcd IF=20mA (Note 1)
Luminous Intensity Matching Ratio
(dot To dot) Iv-m --- --- 2:1 IF=10mA
Peak Emission Wavelength λp --- 610 --- nm IF=20mA
Dominant Wavelength λd --- 605 --- nm IF=20mA (Note 2)
Spectral Line Half-Width λ--- 20 --- nm IF=20mA
Forward Voltage VF --- 2.1 2.6 V IF=20mA
Reverse Current IR --- --- 50 µA VR=5V
Notes:
1. Luminous intensity is measured with a light sensor and filter combination that
approximates the CIE eye-response curve.
2. The dominant wavelength (λd) is derived from the CIE chromaticity diagram and
represents the single wavelength which defines the color of the device.
Luckylight
Spec No: W12088A/B Rev No: V.2 Date: Sep/08/2003 Page: 5OF 6
Approved:JoJo Checked:Sun Drawn:Liu
Lucky Light Electronics Co., Ltd. http://www.luckylightled.com
Typical Electrical / Optical Characteristics Curves
(25Ambient Temperature Unless Otherwise Noted)
S p ec trum D istribu tio n
Relative Luminous Intensity (%)
Ta=25
0400
100
F orward Curren t & F o rw a rd Voltag e
Forward Current IF (mA)
Ta=25
0
10
20
30
40
50
1.7 1.9 2.1 2.3 2.5
Forw ard V oltage V F (V )
300 500 600 700 800
W avelength λp (nm)
75
50
25
Lum inous Intensity &
A m bient T em perature
Relative Luminous Intensity (%)
1
1000
-60
A m bient Tem perature Ta ( )
100
10
-40 -20 0 20 40 60 80 100
Lum inous Intensity & Forward C urrent
Relative Luminous Intensity (%)
1
1000
10 Fo rw ard C u rrent IF (mA)
100
10
0101102103
F orward C u rren t De rating Curv e
Forward Current IF (mA)
0
0
5
15
25
35
45
A m bient Tem perature Ta ( )
f=1KHz
Duty=1/10
Ta=25
20 40 60 80 100
2.7
Luckylight
Spec No: W12088A/B Rev No: V.2 Date: Sep/08/2003 Page: 6OF 6
Approved:JoJo Checked:Sun Drawn:Liu
Lucky Light Electronics Co., Ltd. http://www.luckylightled.com
Please read the following notes before using the datasheets:
1. Over-current-proof
Customer must apply resistors for protection, otherwise slight voltage shift will cause big current
change (Burn out will happen).
2. Storage
2.1 If the package contains a moisture proof bag inside, please don't open the package before
using.
2.2 Before opening the package, the LEDs should be kept at 30or less and 80%RH or less.
2.3 The LEDs should be used within a year.
2.4 After opening the package, the LEDs should be kept at 30or less and 60%RH or less.
3. Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than 260for 5 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals,
and do soldering of each terminal. Be careful because the damage of the product is often started
at the time of the hand solder.
4. Soldering
When soldering, for Lamp without stopper type and must be leave a minimum of 3mm clearance
from the base of the lens to the soldering point.
To avoided the Epoxy climb up on lead frame and was impact to non-soldering problem, dipping
the lens into the solder must be avoided.
Do not apply any external stress to the lead frame during soldering while the LED is at high
temperature.
Recommended soldering conditions:
Soldering Iron Wave Soldering
Temperature
Soldering Time
300Max.
3sec.Max.
(one time only)
Pre-heat
Pre-heat Time
Solder Wave
Soldering Time
100Max.
60 sec. Max.
260Max.
5sec.Max.
Note: Excessive soldering temperature and / or time might result in deformation of the LED lens or catastrophic
failure of the LED.
5. Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used . It should be confirmed beforehand whether the
characteristics of the LEDs will or will not be damaged by repairing.