No. STSE-CC5151A <Cat.No.051031> SPECIFICATIONS FOR NICHIA CHIP TYPE BLUE MODEL : NSSB426CT NICHIA CORPORATION -0- LED Nichia STSE-CC5151A <Cat.No.051031> 1.SPECIFICATIONS (1) Absolute Maximum Ratings Item Forward Current Pulse Forward Current Reverse Voltage Power Dissipation Operating Temperature Storage Temperature Soldering Temperature IFP Conditions : Symbol IF IFP VR PD Topr Tstg Tsld Pulse Width < = 10msec. (2) Initial Electrical/Optical Characteristics Item Symbol Forward Voltage VF Reverse Current IR Luminous Intensity Iv Absolute Maximum Rating 30 100 5 120 -30 ~ + 85 -40 ~ +100 Reflow Soldering : 260C Hand Soldering : 350C and Duty < = 1/10 Condition IF=20[mA] VR= 5[V] IF=20[mA] Typ. (3.6) (156) (Ta=25C) Max. Unit 4.0 V 50 A mcd Min. 150 104 75 (Ta=25C) Max. Unit 213 mcd 150 mcd 104 mcd (3) Ranking Item Luminous Intensity Rank T Rank S Rank R Symbol Iv Iv Iv (Ta=25C) Unit mA mA V mW C C for 10sec. for 3sec. Condition IF=20[mA] IF=20[mA] IF=20[mA] Luminous Intensity Measurement allowance is 10%. Color Rank x y 0.139 0.035 0.129 0.050 (IF=20mA,Ta=25C) Rank W 0.113 0.134 0.145 0.152 0.080 0.105 0.072 0.056 Color Coordinates Measurement allowance is 0.01. One delivery will include up to one color rank and three luminous intensity ranks of the products. The quantity-ratio of the ranks is decided by Nichia. 2.INITIAL OPTICAL/ELECTRICAL CHARACTERISTICS Please refer to figure's page. -1- Nichia STSE-CC5151A <Cat.No.051031> 3.OUTLINE DIMENSIONS AND MATERIALS Please refer to figure's page. Material as follows ; Package : Package Upper Surface Color : Encapsulating Resin : Resin Color : Electrodes : Heat-Resistant Polymer Black Epoxy Resin (Diffused) Blue (Diffused) Ag Plating Copper Alloy 4.PACKAGING * The LEDs are packed in cardboard boxes after taping. Please refer to figure's page. The label on the minimum packing unit shows ; Part Number, Lot Number, Ranking, Quantity * In order to protect the LEDs from mechanical shock, we pack them in cardboard boxes for transportation. * The LEDs may be damaged if the boxes are dropped or receive a strong impact against them, so precautions must be taken to prevent any damage. * The boxes are not water resistant and therefore must be kept away from water and moisture. * When the LEDs are transported, we recommend that you use the same packing method as Nichia. 5.LOT NUMBER The first six digits number shows lot number. The lot number is composed of the following characters; -U - Year ( 4 for 2004, 5 for 2005 ) - Month ( 1 for Jan., 9 for Sep., A for Oct., - Nichia's Product Number U - Ranking by Color Coordinates - Ranking by Luminous Intensity -2- B for Nov. ) Nichia STSE-CC5151A <Cat.No.051031> 6.RELIABILITY (1) TEST ITEMS AND RESULTS Test Item Standard Test Method Test Conditions Note Number of Damaged 2 times 0/100 Resistance to Soldering Heat (Reflow Soldering) JEITA ED-4701 300 301 Tsld=260C, 10sec. (Pre treatment 30C,70%,168hrs.) Thermal Shock JEITA ED-4701 300 307 0C ~ 100C 15sec. 15sec. 100 cycles 0/100 Temperature Cycle JEITA ED-4701 100 105 -40C ~ 25C ~ 100C ~ 25C 30min. 5min. 30min. 5min. 100 cycles 0/100 Moisture Resistance Cyclic JEITA ED-4701 200 203 25C ~ 65C ~ -10C 90%RH 24hrs./1cycle 10 cycles 0/100 High Temperature Storage JEITA ED-4701 200 201 Ta=100C 1000 hrs. 0/100 Temperature Humidity Storage JEITA ED-4701 100 103 Ta=60C, 1000 hrs. 0/100 Low Temperature Storage JEITA ED-4701 200 202 Ta=-40C 1000 hrs. 0/100 Steady State Operating Life Ta=25C, IF=30mA 1000 hrs. 0/100 Steady State Operating Life of High Humidity Heat 60C, RH=90%, IF=20mA 500 hrs. 0/100 Steady State Operating Life of Low Temperature Ta=-30C, IF=20mA 1000 hrs. 0/100 RH=90% (2) CRITERIA FOR JUDGING DAMAGE Criteria for Judgement Min. Max. Item Symbol Test Conditions Forward Voltage VF IF=20mA U.S.L.*) Reverse Current IR VR=5V U.S.L.*) Luminous Intensity IV IF=20mA L.S.L.**) 0.7 *) U.S.L. : Upper Standard Level **) L.S.L. : Lower Standard Level -3- 1.1 2.0 Nichia STSE-CC5151A-1 <Cat.No.060915> 7.CAUTIONS (1) Moisture Proof Package * When moisture is absorbed into the SMT package it may vaporize and expand during soldering. There is a possibility that this can cause exfoliation of the contacts and damage to the optical characteristics of the LEDs. For this reason, the moisture proof package is used to keep moisture to a minimum in the package. * The moisture proof package is made of an aluminum moisture proof bag. A package of a moisture absorbent material (silica gel) is inserted into the aluminum moisture proof bag. The silica gel changes its color from blue to pink as it absorbs moisture. (2) Storage * Storage Conditions Before opening the package : The LEDs should be kept at 30C or less and 90%RH or less. The LEDs should be used within a year. When storing the LEDs, moisture proof packaging with absorbent material (silica gel) is recommended. After opening the package : The LEDs should be kept at 30C or less and 70%RH or less. The LEDs should be soldered within 168 hours (7days) after opening the package. If unused LEDs remain, they should be stored in moisture proof packages, such as sealed containers with packages of moisture absorbent material (silica gel). It is also recommended to return the LEDs to the original moisture proof bag and to reseal the moisture proof bag again. * If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : more than 24 hours at 65 5C * Nichia LED electrodes are silver plated copper alloy. The silver surface may be affected by environments which contain corrosive substances. Please avoid conditions which may cause the LED to corrode, tarnish or discolor. This corrosion or discoloration may cause difficulty during soldering operations. It is recommended that the User use the LEDs as soon as possible. * Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. (3) Heat Generation * Thermal design of the end product is of paramount importance. Please consider the heat generation of the LED when making the system design. The coefficient of temperature increase per input electric power is affected by the thermal resistance of the circuit board and density of LED placement on the board, as well as other components. It is necessary to avoid intense heat generation and operate within the maximum ratings given in this specification. * The operating current should be decided after considering the ambient maximum temperature of LEDs. -4- Nichia STSE-CC5151A-2 <Cat.No.061109> (4) Soldering Conditions * The LEDs can be soldered in place using the reflow soldering method. Nichia cannot make a guarantee on the LEDs after they have been assembled using the dip soldering method. * Recommended soldering conditions Pre-heat Pre-heat time Peak temperature Soldering time Condition Reflow Soldering Lead Solder Lead-free Solder 180 ~ 200C 120 ~ 150C 120 sec. Max. 120 sec. Max. 240C Max. 260C Max. Hand Soldering Temperature Soldering time 350C Max. 3 sec. Max. (one time only) 10 sec. Max. 10 sec. Max. refer to refer to Temperature - profile 1. Temperature - profile 2. (N2 reflow is recommended.) Although the recommended soldering conditions are specified in the above table, reflow or hand soldering at the lowest possible temperature is desirable for the LEDs. A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature. [Temperature-profile (Surface of circuit board)] Use the following conditions shown to the under figure. <1 : Lead Solder> <2 : Lead-free Solder> 1~ 5C / sec. 2.5 ~ 5C / sec. 2.5 ~ 5C / sec. Pre-heating 120 ~ 150C 60sec.Max. Above 200C 240C Max. 10sec. Max. 1~ 5C / sec. Pre-heating 180 ~ 200C 60sec.Max. Above 220C 260C Max. 10sec. Max. 120sec.Max. 120sec.Max. 1.8 1.0 2.8 1.0 0.8 1.0 [Recommended soldering pad design] Use the following conditions shown in the figure. 1.8 (Unit : mm) 4.6 * Occasionally there is a brightness decrease caused by the influence of heat or ambient atmosphere during air reflow. It is recommended that the User use the nitrogen reflow method. * Repairing should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used. It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. * Reflow soldering should not be done more than two times. * When soldering, do not put stress on the LEDs during heating. * After soldering, do not warp the circuit board. (5) Cleaning * It is recommended that isopropyl alcohol be used as a solvent for cleaning the LEDs. When using other solvents, it should be confirmed beforehand whether the solvents will dissolve the package and the resin or not. Freon solvents should not be used to clean the LEDs because of worldwide regulations. * Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic cleaning on the LEDs depends on factors such as ultrasonic power and the assembled condition. Before cleaning, a pre-test should be done to confirm whether any damage to the LEDs will occur. -5- Nichia STSE-CC5151A-1 <Cat.No.060915> (6) Static Electricity * Static electricity or surge voltage damages the LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. * All devices, equipment and machinery must be properly grounded. It is recommended that precautions be taken against surge voltage to the equipment that mounts the LEDs. * When inspecting the final products in which LEDs were assembled, it is recommended to check whether the assembled LEDs are damaged by static electricity or not. It is easy to find static-damaged LEDs by a light-on test or a VF test at a lower current (below 1mA is recommended). * Damaged LEDs will show some unusual characteristics such as the leak current remarkably increases, the forward voltage becomes lower, or the LEDs do not light at the low current. Criteria : (VF > 2.0V at IF=0.5mA) (7) Others * NSSB426C complies with RoHS Directive. * Care must be taken to ensure that the reverse voltage will not exceed the absolute maximum rating when using the LEDs with matrix drive. * The LED light output is strong enough to injure human eyes. Precautions must be taken to prevent looking directly at the LEDs with unaided eyes for more than a few seconds. * Flashing lights have been known to cause discomfort in people; you can prevent this by taking precautions during use. Also, people should be cautious when using equipment that has had LEDs incorporated into it. * The LEDs described in this brochure are intended to be used for ordinary electronic equipment (such as office equipment, communications equipment, measurement instruments and household appliances). Consult Nichia's sales staff in advance for information on the applications in which exceptional quality and reliability are required, particularly when the failure or malfunction of the LEDs may directly jeopardize life or health (such as for airplanes, aerospace, submersible repeaters, nuclear reactor control systems, automobiles, traffic control equipment, life support systems and safety devices). * User shall not reverse engineer by disassembling or analysis of the LEDs without having prior written consent from Nichia. When defective LEDs are found, the User shall inform Nichia directly before disassembling or analysis. * The formal specifications must be exchanged and signed by both parties before large volume purchase begins. * The appearance and specifications of the product may be modified for improvement without notice. -6- Nichia STSE-CC5151A <Cat.No.051031> ICI Chromaticity Diagram 0.9 520 530 0.8 540 510 550 0.7 560 0.6 570 500 0.5 580 y 590 0.4 600 610 0.3 620 630 490 0.2 480 0.1 W 470 460 0 0 0.1 0.2 0.3 0.4 x 1/2 Color Coordinates Measurement allowance is 0.01. -7- 0.5 0.6 0.7 0.8 10 5 2.5 2.0 1.5 1.0 0.5 0 3.0 3.5 4.0 4.5 5.0 Forward Voltage VF (V) Ta=25C 3.0 0 20 40 60 80 100 120 Forward Current IFP (mA) -8- Ambient Temperature vs. Forward Voltage Ambient Temperature vs. Relative Luminosity 5.4 2.0 5.0 4.6 IFP=60mA IFP=20mA IFP=5mA 4.2 3.8 3.4 3.0 2.6 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) IFP=20mA 1.0 0.5 0.2 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Allowable Forward Current IFP (mA) Relative Luminosity (a.u.) 20 Relative Luminosity (a.u.) Forward Current IFP (mA) 50 1 2.5 Forward Voltage VF (V) Ta=25C 200 Ta=25C 100 50 30 20 10 1 5 10 20 50 100 Duty Ratio (%) Ambient Temperature vs. Allowable Forward Current Allowable Forward Current IF (mA) 3.5 200 100 Duty Ratio vs. Allowable Forward Current Forward Current vs. Relative Luminosity Forward Voltage vs. Forward Current 40 30 20 10 0 0 20 40 60 80 100 Ambient Temperature Ta (C) NICHIA CORPORATION NSSB426C Title CHARACTERISTICS No. 050922545221 NNichia STSE-CC5151A <Cat.No.051031> Model Forward Current vs. Chromaticity Coordinate (D) 1mA(473nm) 0.09 y 5mA(472nm) 20mA(470nm) 50mA(468nm) 100mA(467nm) 0.07 0.05 0.03 0.10 0.12 0.14 0.16 0.18 0.20 474 Ta=25C 473 472 471 470 469 468 467 466 1 5 10 20 50 100 Forward Current IFP (mA) Ta=25C IF=20mA 1.0 0.8 0.6 0.4 0.2 0 350 400 450 500 550 600 650 Wavelength (nm) Ambient Temperature vs. Dominant Wavelength Dominant Wavelength D (nm) -9- Dominant Wavelength D (nm) x Forward Current vs. Dominant Wavelength 1.2 Directivity 474 0 1.0 476 IFP=20mA Relative Luminosity (a.u.) Ta=25C 0.11 Relative Emission Intensity (a.u.) 0.13 Spectrum 472 470 468 466 464 -40 -20 0 20 40 60 80 100 Ambient Temperature Ta (C) Ta=25C IFP=20mA X-X Y-Y 10 20 30 40 50 60 0.5 Ta=25C IF=20mA X-X Y-Y 0 90 60 30 Radiation Angle NICHIA CORPORATION 80 0 0.5 90 1.0 NSSB426C Title CHARACTERISTICS No. 050922545231 Nichia STSE-CC5151A <Cat.No.051031> Model 70 3 0.2 (2.6) NC Anode (R 0.8) (1.2) (2.6) 3 0.2 A : Black Cathode mark C 0.5 1.8 0.3 (0.8) (0.4) -10- NC Cathode ITEM MATERIALS PACKAGE PACKAGE UPPER SURFACE COLOR ENCAPSULATING RESIN RESIN COLOR ELECTRODES Heat-Resistant Polymer Black Epoxy Resin (Diffused) Blue (Diffused) Ag Plating Copper Alloy 1 0.2 Model NICHIA CORPORATION Title No. NxSB426C TAPING DIMENSIONS 050922545241 Unit mm 15/1 Scale Allow Nichia STSE-CC5151A <Cat.No.051031> 0.75 0.2 0.85 0.3 K Cathode mark 40.1 Reel End of tape 60+1 -0 Label XXXX LED TYPE NxSx426CT LOT XXXXXX-U QTY pcs 3.150.1 No LEDs 0.2 13 20.1 1+0.25 -0 11.41 90.3 2 1 0.8 3.150.1 (2.75) 3.50.05 20.05 180+0 -3 Reel part 0.250.05 8+0.3 - 0.1 40.1 1.5+0.1 -0 1.750.1 Taping part LEDs mounting part No LEDs -11Top cover tape Pull direction Embossed carrier tape Reel Lead Min.40mm (No LEDs) Reel Lead Min.160mm (No LEDs is more than 40) Reel Lead Min.400mm Taping is based on the JIS C 0806 : Packaging of Electronic Components on Continuous Tapes. Model NICHIA CORPORATION Title No. NxSx426CT TAPING DIMENSIONS 050324538351 Unit mm Scale Allow Nichia STSE-CC5151A <Cat.No.051031> 2,000pcs/Reel Nichia STSE-CC5151A <Cat.No.051031> The reel and moisture absorbent material are put in the moisture proof foil bag and then heat sealed. Reel Label NICHIA Seal XXXX LED TYPE LOT QTY NxSx426xT xxxxxx-U PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Moisture proof foil bag Moisture absorbent material The box is partitioned with the cardboard. Label NICHIA Nichia XXXX LED LED TYPE RANK QTY NxSx426xT U PCS NICHIA CORPORATION 491 OKA, KAMINAKA, ANAN, TOKUSHIMA, JAPAN Packing unit Moisture proof foil bag Cardboard box Cardboard box S Cardboard box M Cardboard box L Reel/bag 1reel Quantity/bag (pcs) 2,000 MAX. Dimensions (mm) 2912371208t 2592472435t 4442622598t Reel/box 7reel MAX. 15reel MAX. 30reel MAX. NICHIA CORPORATION -12-13- Quantity/box (pcs) 14,000 MAX. 30,000 MAX. 60,000 MAX. Model NxSx426xT Title PACKING No. 050922545401