TinyLogic HS 2-Input OR Gate NC7S32 Description The NC7S32 is a single 2-Input high performance CMOS OR Gate. Advanced Silicon Gate CMOS fabrication assures high speed and low power circuit operation over a broad VCC range. ESD protection diodes inherently guard both inputs and output with respect to the VCC and GND rails. Three stages of gain between inputs and outputs assures high noise immunity and reduced sensitivity to input edge rate. www.onsemi.com MARKING DIAGRAMS Features * * * * * * * * * SIP6 CASE 127EB Space Saving SC-74A and SC-88A 5-Lead Package Ultra Small MicroPakTM Leadless Package High Speed: tPD = 3.5 ns Typ Low Quiescent Power: ICC < 1 mA Balanced Output Drive: 2 mA IOL, -2 mA IOH Broad VCC Operating Range: 2 V - 6 V Balanced Propagation Delays Specified for 3 V Operation These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS Compliant Pin 1 IEEE / IEC A B 1 TTKK XYZ SC-74A CASE 318BQ 7S32MG G SC-88A CASE 419A-02 S32MG G Y TT, 7S32, S32 KK XY Z M Figure 1. Logic Symbol = Specific Device Code = 2-Digit Lot Run Traceability Code = 2-Digit Date Code Format = Assembly Plant Code = Date Code* *Date Code orientation and/or position may vary depending upon manufacturing location. ORDERING INFORMATION See detailed ordering, marking and shipping information in the package dimensions section on page 5 of this data sheet. (c) Semiconductor Components Industries, LLC, 2003 January, 2021 - Rev. 5 1 Publication Order Number: NC7S32/D NC7S32 Pin Configurations A 1 5 VCC B 2 GND 3 4 Y A 1 6 VCC B 2 5 NC GND 3 Figure 2. SC-88A and SC-74A (Top View) 4 Y Figure 3. MicroPak (Top Through View) PIN DESCRIPTIONS FUNCTION TABLE (Y = A + B) Pin Name Description Output Inputs A, B Inputs A B Y Y Output L L L No Connect L H H H L H H H H NC H = HIGH Logic Level L = LOW Logic Level ABSOLUTE MAXIMUM RATINGS Symbol VCC IIK Parameter Supply Voltage DC Input Diode Current VIN DC Input Voltage IOK DC Output Diode Current Min Max Unit -0.5 6.5 V mA VIN < 0 V - -20 VIN > VCC - +20 -0.5 VCC + 0.5 V VOUT < 0 V - -20 mA VOUT > VCC - +20 -0.5 VCC + 0.5 V VOUT DC Output Voltage IOUT DC Output Source or Sink Current - 12.5 mA DC VCC or Ground Current per Output Pin - 25 mA ICC or IGND TSTG Storage Temperature -65 +150 C TJ Junction Temperature - +150 C TL Lead Temperature (Soldering, 10 Seconds) - +260 C PD Power Dissipation in Still Air SC-74A - 390 mW SC-88A - 332 MicroPak-6 - 812 Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. www.onsemi.com 2 NC7S32 RECOMMENDED OPERATING CONDITIONS Symbol Parameter Min Max Unit 2.0 6.0 V Input Voltage 0 VCC V Output Voltage 0 VCC V -40 +85 C VCC at 2.0 V 0 20 ns VCC at 3.0 V 0 20 VCC at 4.5 V 0 10 VCC at 6.0 V 0 5 SC-74A - 320 SC-88A - 377 MicroPak-6 - 154 VCC Supply Voltage VIN VOUT TA Operating Temperature tr, tf Input Rise and Fall Times qJA Conditions Thermal Resistance C/W Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended Operating Ranges limits may affect device reliability. 1. Unused inputs must be held HIGH or LOW. They may not float. DC ELECTICAL CHARACTERISTICS TA = +25C Symbol Parameter VCC (V) Conditions TA = -40 to +85C Min Typ Max Min Max Unit VIH HIGH Level Input Voltage 2.0 3.0 - 6.0 1.50 0.7 VCC - - - - 1.50 0.7 VCC - - V VIL LOW Level Input Voltage 2.0 3.0 - 6.0 - - - - 0.50 0.3 VCC - - 0.50 0.3 VCC V VOH HIGH Level Output Voltage 1.90 2.90 4.40 5.90 2.0 3.0 4.5 6.0 - - - - 1.90 2.90 4.40 5.90 - - - - V 2.68 4.18 5.68 2.85 4.35 5.85 - - - 2.63 4.13 5.63 - - - - - - - 0.0 0.0 0.0 0.0 0.10 0.10 0.10 0.10 - - - - 0.10 0.10 0.10 0.10 2.0 3.0 4.5 6.0 3.0 4.5 6.0 VOL LOW Level Output Voltage 2.0 3.0 4.5 6.0 IOH = -20 mA VIN = VIH or VIL VIN = VIH or VIL IOH = -1.3 mA IOH = -2.0 mA IOH = -2.6 mA IOL = 20 mA VIN = VIH or VIL 3.0 4.5 6.0 VIN = VIH or VIL IOL = 1.3 mA IOL = 2.0 mA IOL = 2.6 mA - - - 0.1 0.1 0.1 0.26 0.26 0.26 - - - 0.33 0.33 0.33 V V V IIN Input Leakage Current 6.0 VIN = VCC, GND - - 0.1 - 1.0 mA ICC Quiescent Supply Current 6.0 VIN = VCC, GND - - 1.0 - 10.0 mA www.onsemi.com 3 NC7S32 AC ELECTRICAL CHARACTERISTICS TA = +25C TA = -40 to +85C Min Typ Max Min Max Unit CL = 15 pF - 3.5 15 - - ns 2.0 3.0 4.5 6.0 CL = 50 pF - - - - 20 12 8 7 100 27 20 17 - - - - 125 35 25 21 ns 5.0 CL = 15 pF - 3.0 10 - - ns 2.0 3.0 4.5 6.0 CL = 50 pF - - - - 25 16 11 9 125 35 25 21 - - - - 155 45 30 26 ns - 2 10 - 10 pF - 6 - - - pF Symbol Parameter VCC (V) tPLH, tPHL Propagation Delay (Figure 4, 6) 5.0 tTLH, tTHL Output Transition Time (Figure 4, 6) CIN Input Capacitance CPD Power Dissipation Capacitance (Figure 5) Conditions Open 5.0 (Note 2) 2. CPD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD) at no output loading and operating at 50% duty cycle. CPD is related to ICCD dynamic operating current by the expression: ICCD = (CPD) (VCC) (fIN) + (ICCstatic). AC Loading and Waveforms VCC INPUT OUTPUT CL CL includes load and stray capacitance Input PRR = 1.0 MHz; tW = 500 ns Figure 4. AC Test Circuit Figure 6. AC Waveforms VCC A INPUT Input = AC Waveforms; PRR = Variable; Duty Cycle = 50%. Figure 5. ICCD Test Circuit www.onsemi.com 4 NC7S32 ORDERING INFORMATION Top Mark Package Description Shipping NC7S32M5X 7S32 SC-74A 3000 / Tape & Reel NC7S32P5X S32 SC-88A 3000 / Tape & Reel NC7S32L6X TT SIP6, MicroPak 5000 / Tape & Reel Part Number For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. MicroPak is trademark of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries. www.onsemi.com 5 MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SIP6 1.45X1.0 CASE 127EB ISSUE O DOCUMENT NUMBER: DESCRIPTION: 98AON13590G SIP6 1.45X1.0 DATE 31 AUG 2016 Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2019 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SC-74A CASE 318BQ ISSUE B 5 1 SCALE 2:1 5X DATE 18 JAN 2018 b 0.20 C A B E1 5 M 4 1 2 E 3 B 0.05 A1 e D A L DETAIL A NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994. 2. CONTROLLING DIMENSION: MILLIMETERS. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. MOLD FLASH, PROTRUSIONS, OR GATE BURRS SHALL NOT EXCEED 0.15 PER SIDE. DIM A A1 b c D E E1 e L M TOP VIEW A SIDE VIEW DETAIL A C c SEATING PLANE END VIEW RECOMMENDED SOLDERING FOOTPRINT* MILLIMETERS MIN MAX 0.90 1.10 0.01 0.10 0.25 0.50 0.10 0.26 2.85 3.15 2.50 3.00 1.35 1.65 0.95 BSC 0.20 0.60 0_ 10 _ GENERIC MARKING DIAGRAM* 0.95 PITCH XXX MG G XXX M G 2.40 = Specific Device Code = Date Code = Pb-Free Package (Note: Microdot may be in either location) 5X 1.00 *This information is generic. Please refer to device data sheet for actual part marking. Pb-Free indicator, "G" or microdot " G", may or may not be present. Some products may not follow the Generic Marking. 5X 0.70 DIMENSIONS: MILLIMETERS *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. DOCUMENT NUMBER: DESCRIPTION: 98AON66279G SC-74A Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2018 www.onsemi.com MECHANICAL CASE OUTLINE PACKAGE DIMENSIONS SC-88A (SC-70-5/SOT-353) CASE 419A-02 ISSUE L SCALE 2:1 A NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419A-01 OBSOLETE. NEW STANDARD 419A-02. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. G 5 4 -B- S 1 2 DATE 17 JAN 2013 DIM A B C D G H J K N S 3 D 5 PL 0.2 (0.008) B M M N INCHES MIN MAX 0.071 0.087 0.045 0.053 0.031 0.043 0.004 0.012 0.026 BSC --0.004 0.004 0.010 0.004 0.012 0.008 REF 0.079 0.087 MILLIMETERS MIN MAX 1.80 2.20 1.15 1.35 0.80 1.10 0.10 0.30 0.65 BSC --0.10 0.10 0.25 0.10 0.30 0.20 REF 2.00 2.20 J GENERIC MARKING DIAGRAM* C K H XXXMG G SOLDER FOOTPRINT 0.50 0.0197 XXX = Specific Device Code M = Date Code G = Pb-Free Package 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 (Note: Microdot may be in either location) *This information is generic. Please refer to device data sheet for actual part marking. Pb-Free indicator, "G" or microdot "G", may or may not be present. Some products may not follow the Generic Marking. mm inches STYLE 1: PIN 1. BASE 2. EMITTER 3. BASE 4. COLLECTOR 5. COLLECTOR STYLE 2: PIN 1. ANODE 2. EMITTER 3. BASE 4. COLLECTOR 5. CATHODE STYLE 3: PIN 1. ANODE 1 2. N/C 3. ANODE 2 4. CATHODE 2 5. CATHODE 1 STYLE 4: PIN 1. SOURCE 1 2. DRAIN 1/2 3. SOURCE 1 4. GATE 1 5. GATE 2 STYLE 6: PIN 1. EMITTER 2 2. BASE 2 3. EMITTER 1 4. COLLECTOR 5. COLLECTOR 2/BASE 1 STYLE 7: PIN 1. BASE 2. EMITTER 3. BASE 4. COLLECTOR 5. COLLECTOR STYLE 8: PIN 1. CATHODE 2. COLLECTOR 3. N/C 4. BASE 5. EMITTER STYLE 9: PIN 1. ANODE 2. CATHODE 3. ANODE 4. ANODE 5. ANODE DOCUMENT NUMBER: DESCRIPTION: 98ASB42984B STYLE 5: PIN 1. CATHODE 2. COMMON ANODE 3. CATHODE 2 4. CATHODE 3 5. CATHODE 4 Note: Please refer to datasheet for style callout. If style type is not called out in the datasheet refer to the device datasheet pinout or pin assignment. Electronic versions are uncontrolled except when accessed directly from the Document Repository. Printed versions are uncontrolled except when stamped "CONTROLLED COPY" in red. SC-88A (SC-70-5/SOT-353) PAGE 1 OF 1 ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ON Semiconductor does not convey any license under its patent rights nor the rights of others. (c) Semiconductor Components Industries, LLC, 2018 www.onsemi.com ON Semiconductor and are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries. ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein. ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards, regardless of any support or applications information provided by ON Semiconductor. "Typical" parameters which may be provided in ON Semiconductor data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Email Requests to: orderlit@onsemi.com ON Semiconductor Website: www.onsemi.com TECHNICAL SUPPORT North American Technical Support: Voice Mail: 1 800-282-9855 Toll Free USA/Canada Phone: 011 421 33 790 2910 www.onsemi.com 1 Europe, Middle East and Africa Technical Support: Phone: 00421 33 790 2910 For additional information, please contact your local Sales Representative