11640-842 - ON Semiconductor L.L.C.

2.27.02

FS6183-04

FS6183-04FS6183-04

FS6183-04

1 PLL Cl ock Generator IC

1 PLL Cl ock Generator IC1 PLL Cl ock Generator IC

1 PLL Cl ock Generator IC

ISO9001

ISO9001ISO9001

ISO9001

1.0 Features

• Three output clock frequencies

• Output enable function

• Crystal oscillat or tunab le with ex terna l varac tor

• 3.3V supply voltage (contact factory for 5V)

• Low phase noise, low jitter

• Small circuit board footprint (8-pin 0.150″ SOIC)

• Special high transconductance cry stal oscillator suit-

able for external varactor VCXO function if desired

• Custom frequency selections available - contact your

local AMI Sales Representative for more information

Figure 1: Pin Configuration

1 8

CLKA

GND

XIN

XOUT

VDD

CLKC

CLKB

FS6183

8-pin (0.150″) SOIC

2.0 Description

The FS6183 is a monolithic CMOS clock generator IC

designed to m inim ize cost a nd com ponen t count in digi tal

video/audio systems.

A high-resolution phase-locked loop generates three out-

put clocks (CLKA, CLKB, & CLKC) through an array of

post-dividers. All frequencies are ratiometrically derived

from the crystal frequency. The locking of all the output

frequenc ies toget her can el iminate unpre dictable artif acts

in video s ystems.

Table 1: Crystal / Output Frequencies

DEVICE fXIN

(MHz) CLKA

(MHz) CLKB

(MHz) CLKC

(MHz)

FS6183-04 14.31818 24.576

-0.66ppm 24.576

-0.66ppm

NOTE: Contact AMI for custom PLL frequencies and 5 volt operation

Figure 2: Block Diagram

CRYSTAL

OSC.

FS6183

PLL

XOUT

XIN

CLKC

CLKA

DIVIDER

ARRAY

CLKB

22.27.02

FS6183-04

FS6183-04FS6183-04

FS6183-04

1 PLL

1 PLL1 PLL

1 PLL Clock Ge nerator IC

Clock Ge nerator ICClock Ge nerator IC

Clock Ge nerator IC

ISO9001

ISO9001ISO9001

ISO9001

Table 2: Pin Descriptions

Key: AI = Analog Input; AO = Analog Output; DI = Digital Input; DIU = Input with Internal Pull-Up; DID = Input with Internal Pull-Down; DIO = Digital Input/Output; DI-3 = Three-Level Digital Input,

DO = Digital Output; P = Power/Ground; # = Active Low pin

PIN TYPE NAME DESCRIPTION

1DOCLKAClock Output A

2 P GND Ground

3 AI XIN Crystal Oscillator Feedback

4 AO XOUT Crystal Oscillator Drive

5DOCLKBClock Output B

6DOCLKCClock Output C

7 P VDD Power Supply (+3.3V)

8DI

UOE Output Enable

3.0 Functional Bl ock Descripti on

3.1 Phase-Locked Loop (PLL)

The on-chip PLLs are a standard frequency- and phase-

lock ed loop archi tec tur e. The PLL multiplies t he reference

oscillator to the desired frequency by a ratio of integers.

The frequency multiplication is exact with a zero synthe-

sis error.

3.2 Crystal Oscillator

The oscillator operates the crystal resonator in the paral-

lel-resonant mode.

32.27.02

FS6183-04

FS6183-04FS6183-04

FS6183-04

1 PLL Cl ock Generator IC

1 PLL Cl ock Generator IC1 PLL Cl ock Generator IC

1 PLL Cl ock Generator IC

ISO9001

ISO9001ISO9001

ISO9001

4.0 Electrical Specifications

Table 3: Absolute Maximum Ratings

Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These conditions represent a stress rating only, and functional operation of the device at

these or any other conditions above the operational limits noted in this specification is not implied. Exposure to maximum rating conditions for extended conditions may affect device performance,

functionality, and reliability.

PARAMETER SYMBOL MIN. MAX. UNITS

Supply Voltage (VSS = ground) VDD VSS-0.5 7 V

Input Voltage, dc VIVSS-0.5 VDD+0.5 V

Output Voltage, dc VOVSS-0.5 VDD+0.5 V

Input Clamp Current, dc (V I < 0 or VI > VDD)I

IK -50 50 mA

Output Clamp Current, dc (VI < 0 or VI > VDD)I

OK -50 50 mA

Storage Temperature Range (non-condensing) TS-65 150 °C

Ambient Temperature Range, Under Bias TA-55 125 °C

Junction Temperature TJ125 °C

Lead Temperature (soldering, 10s) 260 °C

Input Static Disc harge Voltage Protection (MIL-STD 883E, Method 3015.7) 2 kV

CAUTION: ELECTROSTATIC SENSITIVE DEVICE

Permanent damage res ulting in a loss of functi onality or performance may occur if this devic e is subjected to a high-energy elec-

trostatic discharge.

Table 4: Operating Conditions

PARAMETER SYMBOL CONDITIONS/DESCRIPTION MIN. TYP. MAX. UNITS

Supply Voltage VDD 3.3V ± 10% 3.0 3.3 3.6 V

Ambient Operating Temperature Range TA070°C

42.27.02

FS6183-04

FS6183-04FS6183-04

FS6183-04

1 PLL

1 PLL1 PLL

1 PLL Clock Ge nerator IC

Clock Ge nerator ICClock Ge nerator IC

Clock Ge nerator IC

ISO9001

ISO9001ISO9001

ISO9001

Table 5: DC Electrical Specifications

Unless otherwise stated, VDD = 3.3V ± 10%, no load on any output, and ambient temperature range TA = 0°C to 70°C. Parameters denoted with an asterisk ( * ) represent nominal characterization

data and are not production tested to any specific limits. Where given, MIN and MAX characterization data are ± 3σ from typical. Negative currents indicate current flows out of the device.

PARAMETER SYMBOL CONDITIONS/DESCRIPTION MIN. TYP. MAX. UNITS

Overall

Supply Current, Dynamic, with Loaded

Outputs IDD fXTAL = 13.5MHz; CL = 10pF 20 mA

Crystal Oscillator

Crystal Resonator Frequency fXTAL Fundamental Mode - 13.5 - MHz

Crystal Loadi ng Capaci tance CL(xtal) As seen by a crystal connected to XIN and

XOUT 17 pF

Crystal Oscillator Drive Transconductance gmOSC VDD = 3.3V 16 mSiemens

Oscillator Source Current IOH VDD = 3.3V

V(XIN) = 0V, V(XOUT) = 0V -18 mA

Oscillator Sink Current IOL VDD = 3.3V

V(XIN) = VDD, V(XOUT) = VDD 23 mA

Clock Outputs (CLKA, CLKB, CLKC)

High-Level Output Sourc e Current * IOH VO = 2.0V 40 mA

Low-Level Output Sink Current * IOL VO = 0.4V 17 mA

zOH VO = 0.5VDD; output driving hi gh 25

Output Impedance * zOL VO = 0.5VDD; output driving l o w 25 Ω

Short Circuit S ource Current * IOSH VO = 0V; shorted for 30s, max. -55 mA

Short Circuit S i nk Current * IOSL VO = 3.3V; shorted for 30s, max. 55 mA

Table 6: AC Timing Specifications

Unless otherwise stated, VDD = 3.3V ± 10%, no load on any output, and ambient temperature range TA = 0°C to 70°C. Parameters denoted with an asterisk ( * ) represent nominal characterization

data and are not production tested to any specific limits. Where given, MIN and MAX characterization data are ± 3σ from typical.

PARAMETER SYMBOL CONDITIONS/DESCRIPTION CLOCK

(MHz) MIN. TYP. MAX. UNITS

Clock Outputs (CLKx)

Duty Cycle * thi / tclk; Measured at VDD/2 45 55 %

Jitter, Absolute Period (pk-pk) * tj(∆P) From rising edge to next ris i ng edge at

VDD/2, CL = 10pF 300 ps

Jitter, RMS Long Term (σy(τ)) * tj(LT) From 0-500µs at VDD/2, CL = 10pF

compared to ideal clock source 150 ps

Rise Time * trVDD = 3.3V; VO = 0.3V to 3.0V; CL = 10pF 1 ns

Fall Time * tfVDD = 3.3V; VO = 3.0V to 0.3V; CL = 10pF 1 ns

Output Frequency Synthesis Error (unless otherwise noted in Frequency Table) 0 ppm

52.27.02

FS6183-04

FS6183-04FS6183-04

FS6183-04

1 PLL Cl ock Generator IC

1 PLL Cl ock Generator IC1 PLL Cl ock Generator IC

1 PLL Cl ock Generator IC

ISO9001

ISO9001ISO9001

ISO9001

5.0 Package Information

Table 7: 8-pin SOIC (0.150") Package Dimensions

DIMENSIONS

INCHES MILLIMETERS

MIN. MAX. MIN. MAX.

A 0.061 0.068 1.55 1.73

A1 0.004 0.0098 0.102 0.249

A2 0.055 0.061 1.40 1.55

B 0.013 0.019 0.33 0.49

C 0.0075 0.0098 0.191 0.249

D 0.189 0.196 4.80 4.98

E 0.150 0.157 3.81 3.99

e 0.050 BSC 1.27 BSC

H 0.230 0.244 5.84 6.20

h 0.010 0.016 0.25 0.41

L 0.016 0.035 0.41 0.89

Θ0°8°0°8°

SEATING

PLANE

1ALL RADII:

0.005" TO 0.01"

BASE

PLANE

AMERICAN MICRO S Y STEMS, INC.

7° typ.h x 45°

Table 8: 8-pin SOIC (0.150") Package Characteristics

PARAMETER SYMBOL CONDITIONS/DESCRIPTION TYP. UNITS

Thermal Impedance, Junction to Free-Air

8-pin 0.150” SOIC ΘJA Air flow = 0 m/s 110 °C/W

Corner lead 2.0

Lead Inductanc e, Self L11 Center lead 1.6 nH

Lead Inductanc e, Mutual L12 Any lead to any adjacent l ead 0.4 nH

Lead Capacitance, Bulk C11 Any lead to VSS 0.27 pF

62.27.02

FS6183-04

FS6183-04FS6183-04

FS6183-04

1 PLL

1 PLL1 PLL

1 PLL Clock Ge nerator IC

Clock Ge nerator ICClock Ge nerator IC

Clock Ge nerator IC

ISO9001

ISO9001ISO9001

ISO9001

6.0 Ordering Information

ORDERING CODE DEVICE

NUMBER P ACKAGE TYPE OPERATING

TEMPERATURE RANGE SHIPPI NG CONFIGURATION

11640-842 FS6183-04 8-pin (0.150”) S OIC

(Small Outline Package) 0°C to 70°C (Commercial) Tape and Reel

Devices sold by AMI are covered by the warranty and patent indemnification provisions appearing in its Terms of Sale only. AMI

makes no warranty, express, statutory implied or by description, regarding the information set forth herein or regarding the freedom

of the described devices from patent infringement. AMI makes no warranty of merchantability or fitness for any purposes. AMI re-

serves the right to discontinue production and change specifications and prices at any time and without notice. AMI’s products are

intended for use in commercial applications. Applications requiring extended temperature range, unusual environmental require-

ments, or high reliability applications, such as military, medical life-support or life-sustaining equipment, are specifically not recom-

mended without additional processing by AMI for such applications.

American Microsystems, Inc., 2300 Buckskin Rd., Pocatello, ID 83201, (208) 233-4690, FAX (208) 234-6796,

WWW Address: http://www.amis.com E-mail: tgp@amis.com