NJM37717
STEPPER MOTOR DRIVER
GENERAL DESCRIPTION PACKAGE OUTLINE
NJM37717 is a stepper motor diver, which consists of a LS-TTL
compatible logic input stage, a current sensor, a monostable
multivibrator and a high power H-bridge output stage with built-in
protection diodes.
NJM37717 is a high voltage version and pin compatible with
NJM3717. The output current is up to 1200mA. Two NJM37717
and a small number of external components from a complete
control and drive unit for stepper moter system.
FEATURES
Half-step and full-step modes
Switched mode bipolar constant current drive
Wide range of current control 5 - 1200 mA
Wide voltage range 10 - 60 V
Thermal overload protection
Packages DIP16
BLOCK DIAGRAM
Figure 1. Block diagram
NJM37717
PIN DESCRIPTION
DIP Symbol Description
1 MBMotor output B, Motor current flows from MA to MB when Phase is high.
2 T Clock oscillator. Timing pin connect a 56 k resistor and a 820 pF in
parallel between T and Ground.
3,14 VMM Motor supply voltage, 10 to 56 V. VMM pins should be wired together on
PCB.
4,5 GND Ground and negative supply. Note these pins are used for heatsinking.
12,13 Make sure that all ground pins are soldered onto a suitable large copper
ground plane for efficient heat sinking.
6 VCC Logic voltage supply normally +5 V.
7 I1Logic input, it controls, together with the I0 input, the current level in the
output stage. The controllable levels are fixed to 100, 60, 20, 0%.
8 Phase Controls the direction of the motor current of MA and MB outputs. Motor
current flows from MA to MB when the phase input is high.
9 I0Logic input, it controls, together with the I1 input, the current level in the
output stage. The controlable levels are fixed to 100, 60, 20, 0%.
10 C Comparator input. This input senses the instantaneous voltage across the
sensing resistor, filtered through a RC Network.
11 VRReference voltage. Controls the threshold voltage of the comparator and
hence the output current. Input resistance: typically 6.8k ± 20%.
15 MAMotor output A, Motor current flows from MA to MB when Phase is high.
16 E Common emitter. Connect the sense resistor between this pin and ground.
Figure 2. Pin configurations
PIN CONFIGURATIONS
NJM37717
Figure 3. Definition of terms
FUNCTIONAL DESCRIPTION
The NJM37717 is intended to drive a bipolar constant current through one motor winding of a 2-phase stepper
motor.
Current control is achieved through switched-mode regulation, see figure 4 and 5.
Three different current levels and zero current can be selected by the input logic.
The circuit contains the following functional blocks:
Input logic
Current sense
Single-pulse generator
Output stage
Input logic
Phase input. The phase input determines the direction of the current in the motor winding. High input forces the
current from terminal MA to MB and low input from terminal MB to MA. A Schmitt trigger provides noise immunity and
a delay circuit eliminates the risk of cross conduction in the output stage during a phase shift.
Half- and full-step operation is possible.
Current level selection. The status of I0 and I1 inputs determines the current level in the motor winding. Three fixed
current levels can be selected according to the table below.
Motor current I0I1
High level 100% L L
Medium level 60% H L
Low level 20% L H
Zero current 0% H H
The specific values of the different current levels are determined by the reference voltage VR together with the value
of the sensing resistor RS.
The peak motor current can be calculated as follows:
im = (VR • 0.083) / RS [A], at 100% level
im = (VR • 0.050) / RS [A], at 60% level
im = (VR • 0.016) / RS [A], at 20% level
The motor current can also be continuously varied by modulating the voltage reference input.
NJM37717
Current sensor
The current sensor contains a reference voltage divider and three comparators for measuring each of the select-
able current levels. The motor current is sensed as a voltage drop across the current sensing resistor, RS, and
compared with one of the voltage references from the divider. When the two voltages are equal, the comparator
triggers the single-pulse generator. Only one comparator at a time is activated by the input logic.
Single-pulse generator
The pulse generator is a monostable multivibrator triggered on the positive edge of the comparator output. The
multivibrator output is high during the pulse time, toff , which is determined by the timing components RT and CT.
toff = 0.69 • RT • CT
The single pulse switches off the power feed to the motor winding, causing the winding to decrease during toff.If a
new trigger signal should occur during toff , it is ignored.
Output stage
The output stage contains four transistors and four diodes, connected in an H-bridge. The two sinking transistors
are used to switch the power supplied to the motor winding, thus driving a constant current through the winding.
See figures 4 and 5.
Overload protection
The circuit is equipped with a thermal shut-down function, which will limit the junction temperature. The output
current will be reduced if the maximum permissible junction temperature is exceeded. It should be noted, however,
that it is not short circuit protected.
Operation
When a voltage VMM is applied across the motor winding, the current rise follows the equation:
im = (VMM / R) • (1 - e-(R • t ) / L )
R = Winding resistance
L = Winding inductance
t = time
(see figure 5, arrow 1)
The motor current appears across the external sensing resistor, RS, as an analog voltage. This voltage is fed
through a low-pass filter, RCCC, to the voltage comparator input (pin 10). At the moment the sensed voltage rises
above the comparator threshold voltage, the monostable is triggered and its output turns off the conducting sink
transistor.
The polarity across the motor winding reverses and the current is forced to circulate through the appropriate
upper protection diode back through the source transistor (see figure 5, arrow 2).
After the monostable has timed out, the current has decayed and the analog voltage across the sensing resistor is
below the comparator threshold level.
The sinking transistor then closes and the motor current starts to increase again, The cycle is repeated until the
current is turned off via the logic inputs.
By reversing the logic level of the phase input (pin 8), both active transistors are turned off and the opposite pair
turned on after a slight delay. When this happens, the current must first decay to zero before it can reverse. This
current decay is steeper because the motor current is now forced to circulate back through the power supply and
the appropriate sinking transistor protection diode. This causes higher reverse voltage build-up across the winding
which results in a faster current decay (see figure 5, arrow 3).
For best speed performance of the stepper motor at half-step mode operation, the phase logic level should be
changed at the same time the current-inhibiting signal is applied (see figure 6).
NJM37717
Figure 6. Principal operating sequence
Figure 5. Output stage with current
paths for fast and slow current decay
Figure 4. Motor current (IM ),
Vertical : 200 mA/div, Horizontal: 1
ms/div, expanded part 100 µs/div
NJM37717
Figure7. Definition of symbols
ABSOLUTE MAXIMUM RATINGS (Ta=25°C)
Parameter Pin [DIP] Symbol Min Max Unit
Voltage
Logic supply 6 VCC 0 7 V
Motor supply 3, 14 VMM 0 60 V
Logic inputs 7, 8, 9 VI-0.3 6 V
Comparator input 10 VC-0.3 VCC V
Reference input 11 VR-0.3 15 V
Current
Motor output current 1, 15 IM-1200 +1200 mA
Logic inputs 7, 8, 9 II-10 - mA
Analog inputs 10, 11 IA-10 - mA
Temperature
Operating junction temperature Tj-40 +150 °C
Storage temperature Tstg -55 +150 °C
RECOMMENDED OPERATING CONDITIONS (Ta=25°C)
Parameter Symbol Min Typ Max Unit
Logic supply voltage VCC 4.75 5 5.25 V
Motor supply voltage VMM 10 - 56 V
Motor output current IM-1000 - +1000 mA
Operating junction temperature Tj-20 - +125 °C
Rise time logic inputs tr- - 2 µs
Fall time logic inputs tf- - 2 µs
NJM37717
ELECTRICAL CHARACTERISTICS
Electrical characteristics over recommended operating conditions, unless otherwise specified .Ta=25°C,CT = 820 pF, RT = 56k
Parameter Symbol Conditions Min Typ Max Unit
General
Supply current ICC - - 25 mA
Total power dissipation PDfs = 28 kHz, IM = 500mA, VMM = 36 V - 1.4 1.7 W
Note 2, 4.
fs = 28 kHz, IM = 800mA, VMM = 36 V - 2.8 3.3 W
Note 3, 4.
Turn-off delay tddVC/dt 50 mV/µs.VMM = 60 V,RL=200- 0.9 1.5 µs
Thermal shutdown junction temperature - 165 - °C
Logic Inputs
Logic HIGH input voltage VIH 2.0 - - V
Logic LOW input voltage VIL - - 0.8 V
Logic HIGH input current IIH VI = 2.4 V - - 20 µA
Logic LOW input current IIL VI = 0.4 V -0.4 - - mA
Reference Input
Input resistance RRTa = +25°C - 6.8 - k
Comparator Inputs
Threshold voltage VCH VR = 5.0 V, I0 = I1 = LOW 400 415 430 mV
Threshold voltage VCM VR = 5.0 V, I0 = HIGH, I1 = LOW 240 250 265 mV
Threshold voltage VCL VR = 5.0 V, I0 = LOW, I1 = HIGH 70 80 90 mV
Input current IC-20 - - µA
Motor Outputs
Lower transistor saturation voltage IM = 500 mA - 0.9 1.2 V
IM = 800 mA - 1.1 1.4 V
Lower diode forward voltage drop IM = 500 mA - 1.2 1.5 V
IM = 800 mA - 1.3 1.7 V
Upper transistor saturation voltage IM = 500 mA - 1.0 1.25 V
IM = 800 mA - 1.2 1.5 V
Upper diode forward voltage drop IM = 500 mA - 1.0 1.25 V
IM = 800 mA - 1.2 1.45 V
Output leakage current I0 = I1 = HIGH, Ta = +25°C - - 100 µA
Monostable
Cut off time toff VMM = 10 V, ton 5 µs 27 31 35 µs
THERMAL CHARACTERISTICS
Parameter Symbol Conditions Min Typ Max Unit
Thermal resistance Rthj-GND DIP package. - 11 - °C/W
RthJ-A DIP package. Note 2. - 40 - °C/W
Notes
1. All voltages are with respect to ground. Currents are positive into, negative out of specified terminal.
2. All ground pins soldered onto a 20 cm2 PCB copper area with free air convection. TA +25°C.
3. DIP package with external heatsink (Staver V7) and minimal copper area. Typical RthJ-A = 27.5°C/W. TA = +25°C.
4. Not covered by final test program.
NJM37717
Applications Information
Motor selection
Some stepper motors are not designed for continuous operation at maximum current. As the circuit drives a con-
stant current through the motor, its temperature can increase, both at low- and high-speed operation.
Some stepper motors have such high core losses that they are not suited for switched-mode operation.
Interference
As the circuit operates with switched-mode current regulation, interference-generation problems can arise in some
applications. A good measure is then to decouple the circuit with a 0.1 µF ceramic capacitor, located near the
package across the power line VMM and ground.
Also make sure that the VR input is sufficiently decoupled. An electrolytic capacitor should be used in the +5 V rail,
close to the circuit.
The ground leads between RS, CC and circuit GND should be kept as short as possible. This applies also to the
leads connecting RS and RC to pin 16 and pin 10 respectively.
In order to minimize electromagnetic interference, it is recommended to route MA and MB leads in parallel on the
printed circuit board directly to the terminal connector. The motor wires should be twisted in pairs, each phase
separately, when installing the motor system.
Unused inputs
Unused inputs should be connected to proper voltage levels in order to obtain the highest possible noise immunity.
Ramping
A stepper motor is a synchronous motor and does not change its speed due to load variations. This means that the
torque of the motor must be large enough to match the combined inertia of the motor and load for all operation
modes. At speed changes, the requires torque increases by the square, and the required power by the cube of the
speed change. Ramping, i.e., controlled acceleration or deceleration must then be considered to avoid motor pull-
out.
VCC , VMM
The supply voltages, VCC and VMM , can be turned on or off in any order. Normal dV/dt values are assumed.
Before a driver circuit board is removed from its system, all supply voltages must be turned off to avoid destruc-
tive transients from being generated by the motor.
Figure 8. Typical stepper motor driver application with NJM37717
NJM37717
Analog control
As the current levels can be continuously controlled by modulating the VR input, limited microstepping can be
achieved.
Switching frequency
The motor inductance, together with the pulse time, toff , determines the switching frequency of the current regulator.
The choice of motor may then require other values on the RT , CT components than those recommended in figure7,
to obtain a switching frequency above the audible range. Switching frequencies above 40 kHz are not recom-
mended because the current regulation can be affected.
Sensor resistor
The RS resistor should be of a non-inductive type, power resistor. A 1.0 ohm resistor, tolerance 1%, is a good
choice for 415 mA max motor current at VR = 5V.
The peak motor current, im , can be calculated by using the formulas:
im = (VR • 0.083) / RS [A], at 100% level
im = (VR • 0.050) / RS [A], at 60% level
im = (VR • 0.016) / RS [A], at 20% level
Heatsinking
The junction temperature of the chip highly effects the lifetime of the circuit. In high-current applications, the
heatsinking must be carefully considered.
The Rthj-a of the NJM37717 can be reduced by soldering the ground pins to a suitable copper ground plane on
the printed circuit board (see figure 10) or by applying an external heatsink type V7 or V8, see figure 9.
The diagram in figure 16 shows the maximum permissible power dissipation versus the ambient temperature in
°C, for heatsinks of the type V7, V8 or a 20 cm2 copper area respectively. Any external heatsink or printed circuit
board copper must be connected to electrical ground.
For motor currents higher than 500 mA, heatsinking is recommended to assure optimal reliability.
The diagrams in figures 9 and 10 can be used to determine the required heatsink of the circuit. In some systems,
forced-air cooling may be available to reduce the temperature rise of the circuit.
Figure 9. Heatsinks, Staver, type V7 and V8 by Columbia-Staver UK
Figure 10. Copper foil used as a heatsink
NJM37717
Figure 14. Typical upper diode voltage
drop vs. recirculating current
Figure 13. Typical lower diode voltage
drop vs. recirculating current
Figure 11. Typical source saturation vs.
output current Figure 12. Typical sink saturation vs.
output current
TYPICAL CHARACTERISTICS
Figure 15. Typical power dissipation vs.
motor current Figure 16. Allowable power dissipation
vs. ambient temperature
The specifications on this databook are only
given for information , without any guarantee
as regards either mistakes or omissions.
The application circuits in this databook are
described only to show representative
usages of the product and not intended for
the guarantee or permission of any right
including the industrial rights.