C
DO NOT
SCALE FROM
THIS PRINT
CLM-1XX-XX-XX-D-XX
No OF POSITIONS / ROW
-02 THRU -50
BODY SPEC
-D: DOUBLE ROW
(USE CLM-XX-D)
LEAD STYLE SPEC
PLATING SPECIFICATION
-F: 3µ" FLASH SELECTIVE GOLD IN CONTACT
AREA MATTE TIN ON TAIL
(PRE-PLATED CONTACT)
-L: 10µ" LIGHT SELECTIVE GOLD IN CONTACT
AREA MATTE TIN ON TAIL
(PRE-PLATED CONTACT)
-G: 10µ" GOLD IN CONTACT AREA 3µ" ON TAIL
(POST-PLATED CONTACT)
-H: 30µ" HEAVY GOLD IN CONTACT AREA
3µ" ON TAIL
(POST-PLATED CONTACT)
-LM: 10µ" LIGHT SELECTIVE GOLD IN CONTACT
AREA MATTE TIN ON TAIL
(PRE-PLATED CONTACT)
-FM: 3µ" FLASH SELECTIVE GOLD IN CONTACT
AREA MATTE TIN ON TAIL
(PRE-PLATED CONTACT)
OPTION
-P: PICK & PLACE PAD
(AVAILABLE ON POS 7 THRU 50 ONLY)
(SEE FIG 3, SHT 2)(USE LMP-04)
-TR: TAPE & REEL
-BE: BOTTOM ENTRY ONLY
(SEE FIG 2)(USE CLM-XX-DBE-XX)
-PA: PICK & PLACE PAD W/ ALIGNMENT PINS
(SEE FIG 4, SHT 2)
-A: ALIGNMENT PIN (USE CLM-XX-D-XX)
(AVAILABLE ON POS 3 THRU 50 ONLY)
(SEE FIG 5, SHT 2)
-K: POLYIMIDE FILM PAD
(AVAILABLE ON POS 7 THRU 50 ONLY)
(.005 [.13] THICKNESS)(SEE FIG 6, SHT 2)
(USE K-DOT-.138-.250-.005)
-02: SURFACE MOUNT
(USE C-117-01-X)
.0835
REF
2.121
"A"
"A"
FIG 1
(SEE NOTE 8)
(No OF POS. X .03937[1.0000] + .0125[.318])
.008
(SEE NOTE 3 AND 7)
.0394 1.000
.0110
x .0050[.127] REF
0.279 .1000 2.540
REF
REF
No. OF POS x .03937[1.0000] - .03937[1.0000]
2
MAX SWAY
(ANY DIRECTION)
C-117-01-X
C-117-01-X
C
L
FIG 2
(SAME AS FIG 1 EXCEPT INSULATOR)
.0885 2.248
(MEASURED AT BEND)
.150
±.010
3.81
±0.254
(SEE NOTE 5)
3°
SECTION "A"-"A"
SCALE 4 : 1
BURR SIDE (SEE NOTE 5)
C
SEE NOTE 9
C
C
C
+1
-3
SHEET OF
UNLESS OTHERWISE SPECIFIED,
DIMENSIONS ARE IN INCHES.
TOLERANCES ARE:
DECIMALS ANGLES
.XX:
.01 [.3] 2
.XXX:
.005 [.13]
.XXXX:
.0020 [.051]
MATERIAL:
LOW PROFILE 1MM x 1MM DOUBLE ROW BODY
BY:
CLM-1XX-XX-XX-D-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
G. PURVIS
08/10/94
2
1
SHEET SCALE: 2:1
BODY: LCP, UL 94 VO
COLOR: BLACK
F:\DWG\MISC\MKTG\CLM-1XX-XX-XX-D-XX-MKT.SLDDRW
TERMINAL:
PHOS BRONZE
NOTES:
1. REPRESENTS CRITICAL DIMENSION.
2. MINIMUM PUSHOUT FORCE: .5 LB.
3. WILL LOSE A POSITION FOR EVERY CUT MADE ON
A SOCKET STRIP.
4. POSITIONS -05 THROUGH -50 ARE TO BE TUBED. POSITIONS
-02 THRU -04 TO BE LAYER PACKAGED ONLY.
5. SHEAR TAILS TO DIMENSIONS SHOWN, .003 MAX SHEAR BURR.
6. PARTS TO BE SYMMETRICAL ABOUT
C
L
.
7. CUT FLASH TO BE .010 [.25] MAX WITH
NO FLASH ALLOWED IN HOLES OR
EXTENDING BELOW LEADS.
8. ENDWALL AFTER CUTTING: .0155±.0025 [.398±.064]
9. COPLANARITY TO BE .0040 FOR POSITIONS 2-25
& .0060 FOR POSITIONS 26-50.
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
REVISION BE
"N"
.225
5.72
REF
"Q"
C
L
FIG 3
-P: PICK & PLACE PAD
AVAILABLE ON POSITIONS 7 THRU 50 ONLY
NOTE: "N" = USED MEASURED DIMENSION (REF)
"Q" = {("N" - .225[5.72]) / 2}
.020[.51]
LMP-04
.0966 2.454
.144 3.66
REF
"M"
"A"
"P"
.325 8.26
REF
C
L
C
L
FIG 4
-PA: PICK & PLACE PAD WITH ALIGNMENT PINS
PPP-39-X-X-XX
C
.1185 3.010
.0535 1.359
REF
.275 6.99
.035 0.89
(TYP)
C
L
.020
REF
0.51
(No OF POS. -2) x .03937 [1.0000]
FIG 5
-A: MOLDED ALIGNMENT PIN
.020
0.51
.015
REF
0.38
"S"
"R"
.019
±.010
0.48
±0.25
.138 3.50
NOTE: "R" = USED MEASURED DIMENSION (REF)
"S" = {("R" - .138[3.50]) / 2}
.020[.51]
.0935
REF
2.375
PT-CLX001-D
PT-CLP001-PA
PT-1-24-01-50
FIG 6
-K: POLYAMIDE FILM PAD
AVAILABLE ON POSITIONS 7 THRU 50 ONLY
-PACKAGING
(SEE NOTE 4)
TABLE 1
POS / ROW
"A"
"M"
"P"
4-15
.140[3.58] REF
USED MEASURED DIMENSION(REF)
{("M" - "A") / 2}
.010[.25]
16-50
.280[7.11] REF
TABLE 3
POSITIONS
PAD
EVEN
4-14
PPP-39-E-4-15
16-50
PPP-39-E-16-50
ODD
5-15
PPP-39-O-4-15
17-49
PPP-39-0-16-50
TABLE 2
(INCLUDES -D & -D-BE)
OPTION
TUBE
PLUG
-P, -A-P
PT-CLX001-D
TP-33
-PA
PT-CLP001-PA
TP-09
-NONE
-A, -A-K,
-K
PT-1-24-01-50
TP-33
SHEET OF
LOW PROFILE 1MM x 1MM DOUBLE ROW BODY
BY:
CLM-1XX-XX-XX-D-XX
DWG. NO.
DESCRIPTION:
PROPRIETARY NOTE
THIS DOCUMENT CONTAINS INFORMATION
CONFIDENTIAL AND PROPRIETARY TO
SAMTEC, INC. AND SHALL NOT BE REPRODUCED
OR TRANSFERRED TO OTHER DOCUMENTS OR
DISCLOSED TO OTHERS OR USED FOR ANY
PURPOSE OTHER THAN THAT WHICH IT WAS
OBTAINED WITHOUT THE EXPRESSED WRITTEN
CONSENT OF SAMTEC, INC.
DO NOT SCALE DRAWING
G. PURVIS
08/10/94
2
2
SHEET SCALE: 4:1
REVISION BE
F:\DWG\MISC\MKTG\CLM-1XX-XX-XX-D-XX-MKT.SLDDRW
520 PARK EAST BLVD, NEW ALBANY, IN 47150
PHONE: 812-944-6733 FAX: 812-948-5047
e-Mail info@SAMTEC.com code 55322
