LoPACTM Family PFC MiniTM, PFC MicroTM, PFC MicroSTM Power Factor Corrected, AC-DC Switchers Features & Benefits PFC Mini 12.20 x 6.00 x 1.72in [309,9 x 152,4 x 43,6mm] Up to 1500W 1 - 6 Outputs * Near unity power factor * EN61000-3-2 harmonic current compliance * Low profile package * Output power to 1,500W * Up to six user-specifiable outputs PFC Micro 10.40 x 5.06 x 1.86in [264,1 x 128,5 x 47,3mm] Up to 800W 1 - 6 Outputs * Universal AC input * Power density up to 11W/in3 * Integral cooling fans * Autosense PFC MicroS 7.95 x 5.06 x 1.86in [201,9 x 128,5 x 47,3mm] Up to 600W 1 - 3 Outputs * Safety agency approvals: CE Marked, cTUVus * Vantage Line[a] * RoHS compliant Product Description The PFC MicroS, PFC Micro and PFC Mini are members of the low profile, high-density LoPAC series of power factor corrected AC-DC power supplies. Available as a one-, two- or three-slot package, respectively, each LoPAC slot can be configured with standard Vicor DC-DC converter modules enabling up to six user-specifiable isolated outputs in a package only 1.72in [43,6mm] high with a power density of 11W/in3. For maximum versatility and flexibility, the LoPAC can be configured with VI-26x (fullbrick), VI-J6x (halfbrick) or Maxi, Mini, Micro V375 Series full-, half- and quarterbrick modules. These modules cover the entire range of outputs from 1 to 100VDC and 25 to 600W. The optimum solution can be factory configured based on your exact voltage and power requirements. For conducted EMI, certain configurations meet EN55022 and FCC Part 15 Class A (consult factory). Harmonic current limits per EN61000-3-2 and Surge Immunity per EN61000-4-5 in addition to a wide variety of safety agency approvals further enhance the LoPAC flexibility. LoPACTM Family Page 1 of 9 Part Numbering PM X1 - X2 Number of Output Voltages Product Prefix PM = PFC Mini PC = PFC Micro PS = PFC MicroS X3 X4 XXXX [a] Optional Factory Assigned Factory Assigned Optional Codes[b] LL = Low Leakage QF = Quiet Fan (only available on PFC Mini) The Vantage Line is the Vicor affordable power supply option. Minor variances in some specifications between the Vantage Line and the Standard Line apply. Contact factory for more information. [b] Refer to Design Guide for more on the optional codes. Rev 2.5 02/2018 -X6 Optional Factory Assigned 2=FasTrak G= RoHS Number of Maxi, Mini or Micro Modules Number of VI-200 TM/ VI-J00TM Modules -X5 LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM DC Output Selections The versatility of the LoPAC series is due in large part to the wide array of Vicor modules available to be configured into the different package formats. Slots can be populated with VI-200TM, VI-J00TM or Maxi, Mini, Micro modules in full-, half- or quarter-brick sizes. The Vicor full VI-26x, VI-J6x and V375 standard product matrices are available to choose from. In addition, the full range of non-standard voltages and powers from 1 to 100VDC and 10 to 600W is also available for inclusion. The table below is just a sampling of some of the most popular standard outputs that can be configured into LoPAC slots. Available Power (W) per Package Size Output Voltage (VDC) Full Brick Half Brick Maxi VI-200 Mini Quarter Brick VI-J00 Micro 2 160 80 60 100 40 30 50 3.3 264 132 99 150 66 50 75 5 400 200 150 200 100 75 100 12 600 200 150 300 100 75 150 15 600 200 150 300 100 75 150 24 600 200 150 300 100 75 150 28 600 200 150 300 100 75 150 48 600 200 150 300 100 75 150 LoPAC Slot Configurations The DC-DC converter modules are used to populate each LoPAC converter slot. Each slot can be configured in different ways depending on module sizes and power limitations. The following table summarizes the available slot configurations for each of the three LoPAC packages. Maximum Output Power Model Type Number of Slots Total Modules per Slot at 230VAC at 115VAC PFC MiniTM 3 1,500W 800W 1 full or 2 half PFC MicroTM 2 800W 500W 1 full or 2 half or 3 quarter PFC MicroSTM 1 600W 500W 1 full or 2 half or 3 quarter Autosense Feature[c] This feature is implemented in all converter slots in the LoPAC family. If remote-sense connections are not needed or are inadvertently not made, no local-sense connections are necessary. [c] Simply connect the output(s) to the load and the converter(s) will automatically operate in the local-sense mode. If remote-sense connections are made, the unit will operate in remote-sense mode. Applies to converter slots utilizing Maxi or Mini size converters. LoPACTM Family Page 2 of 9 Rev 2.5 02/2018 LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM Performance Specifications The following are typical performance specifications at room ambient temperature, nominal line voltage (115 / 230VAC) and 75% load on all outputs, unless specified otherwise. For detail specifications, consult the Design Guide for the LoPAC configuration of interest. This is available at vicorpower.com. Input Characteristics Parameter PFC Mini PFC Micro PFC MicroS Units Notes AC Input Voltage 85 - 264 VAC Frequency (Standard) 47 - 500 Hz Frequency (Vantage) 47 - 63 DC Input 100 - 380 Line Regulation Hz 100 - 300 VDC 0.4 % From low line to high line Inrush Current @ 115VAC 8.57 APK @ 230VAC 1714 APK Ride-Through Time @ Load Conducted EMI / RFI >20 1,200500 ms W FCC Class AFCC Class A (consult factory) EN55022 Class A EN55022 Class A (consult factory) Power Factor >0.98 Harmonic Current Limits EN61000-3-2/A14 Transient Burst Immunity EN61000-4-4 EN61000-4-4 >75% load Class A Level 3, Performance Criteria B Installation Class 3 Surge Immunity EN61000-4-5 Performance Criteria B Dielectric Withstand Primary to Chassis GND 2,121 VDC Primary to Secondary 4,242 VDC Secondary to Chassis GND 750 VDC LoPACTM Family Page 3 of 9 Rev 2.5 02/2018 LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM Performance Specifications (Cont.) The following are typical performance specifications at room ambient temperature, nominal line voltage (115 / 230VAC) and 75% load on all outputs, unless specified otherwise. For detail specifications, consult the Design Guide for the LoPAC configuration of interest. This is available at vicorpower.com. Output Characteristics Parameter PFC Mini PFC Micro PFC MicroS Units Setpoint Accuracy (Standard) 1% (standard), 2% (special) Setpoint Accuracy (Vantage) 2% (standard), 5% (special) Notes Of VNOM Load Regulation 0.05 % 10% to full load 0.2 % No load to full load Temperature Regulation 0.005 %/C Long-Term Drift 0.02 %/khr -20 to +65C Output Ripple & Noise 10VOUT 100 > 10VOUT 1.0 mV 20MHz band width %VOUT 20MHz band width Voltage Trim Range VI-200TM / VI-J00TM modules 50 - 110 %VOUT 10% on 10 - 15VOUT Maxi, Mini, Micro modules 10 - 110 %VOUT Preload may be required Remote Sense Compensation 0.5 VDC Autosense (See page 2) OVP Set Point 125 %VOUT Not available on VI-J00 Modules Current Limit 115 %IMAX Auto recovery Units Notes Environmental Characteristics Parameter PFC Mini Storage Temperature PFC Micro PFC MicroS -40 to +85 C Operating Temperature Full Rated Power (Standard) -20 to +45 C 50% Rated Power (Standard) -20 to +65 C Full Rated Power (Vantage) 0 to +45 C 50% Rated Power (Vantage) 0 to +65 C MIL-STD-810E, Category 10 Vibration Minimum Integrity Test Safety Approvals CE Marked, cTUVus Mechanical Characteristics Parameter Weight Overall Dimensions LoPACTM Family Page 4 of 9 PFC Mini 5.5 [2,5] PFC Micro PFC MicroS 5.2 [2,4]3.1 [1,4] 12.20 x 6.00 x 1.72 10.40 x 5.06 x 1.86 7.95 x 5.06 x 1.86 [309,9 x 152,4 x 43,6] [264,1 x 128,5 x 47,3][201,9 x 128,5 x 47,3] Rev 2.5 02/2018 Units Notes lbs [kg] in [mm] LxWxH LoPACTM Family Page 5 of 9 Rev 2.5 02/2018 4 3 REF DESIGNATION LEGEND MB = MOTHER BOARD S1 = (SLOT 1) DAUGHTERBOARD MODULES E/D 1. S2 = (SLOT 2) DAUGHTERBOARD MODULES E/D 2. S3 = (SLOT 3) DAUGHTERBOARD MODULES E/D 3. A COMPLETE SET OF MATING CONNECTORS CAN BE PURCHASED FROMWESTCOR BY SPECIFYING CONNECTOR KIT P/N: 19-130047 2 WITH OPTIONAL BUSBAR. 1. INTERPRET DRAWING PER ANSI Y14.5-1994. NOTES: UNLESS OTHERWISE SPECIFIED MBJ1 INPUT CONNECTIONS MBJ1-1 EARTH GROUND MBJ1-2 L2 / NEUTRAL MBJ1-3 L1 14 AWG WIRE CLAMPING SCREWS 3 J3 INTERFACE CONNECTION MATING HDWR: (AMP P/N: OR EQUIVALENT) HOUSING: AMP P/N: 205204-4 TERMINALS: AMP P/N: 66506-9 SCREW LOCK: AMP P/N: 205980-4 CRIMP TOOL: AMP 58448-3 J3 INTERFACE PIN OUT 5 1 J3-1 E/D-1 J3-2 E/D-2 9 6 J3-3 E/D-3 J3-4 SIGNAL GROUND J3-5 VCC +5V 300mA J3-6 ACOK AC POWER OK J3-7 GSD GENERAL SHUTDOWN J3-8 SPARE J3-9 SPARE 0.487 12.36 0.920 23.37 1.72 0.02 43.69 0.51 4.00 101.60 1.00 25.40 2.210 56.13 1.600 40.64 5.268 133.81 SCALE: 1:2 BOTTOM VIEW 8.00 203.20 8.00 203.20 12.03 305.56 12.16 308.86 2 0.47 11.94 2.00 50.80 6.00 152.40 FOUR OUTPUT UNIT PICTURED (SEE PAGE 7 FOR DETAILED OUTPUT CONNECTION INFORMATION .) 0.34 0.02 8.64 0.51 CUSTOMER MOUNTING HOLES: 2X #8-32 X 0.156 or M4 X 4mm MAX LG. FROM OUTSIDE OF POWER SUPPLY CUSTOMER MOUNTING HOLES: 4X #8-32 X .156 or M4 X 4mm MAX LG. FROM OUTSIDE OF POWER SUPPLY 2.00 50.80 12.49 0.02 317.29 0.51 PFC MINI LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM Mechanical Drawing, PFC Mini LoPACTM Family Page 6 of 9 REF SGND PGR ACOK ED6 ED5 ED4 ED3 ED2 ED1 GSD PGDV Vcc PIN CBJ3-1 CBJ3-2 CBJ3-3 CBJ3-4 CBJ3-5 CBJ3-6 CBJ3-7 CBJ3-8 CBJ3-9 CBJ3-10 CBJ3-11 CBJ3-12 CBJ3 INTERFACE CONNECTOR SIGNAL GROUND POWER GOOD/READ AC POWER OK ENABLE/DISABLE S2M3 ENABLE/DISABLE S2M2 ENABLE/DISABLE S2M1 ENABLE/DISABLE S1M3 ENABLE/DISABLE S1M2 ENABLE/DISABLE S1M1 GENERAL SHUTDOWN POWER GOOD/DATA VALID +5V@40mA DESCRIPTION Rev 2.5 02/2018 REFERENCE MB CB S(x) M(x) A COMPLETE SET OF MA TING CONNECTORS I S AVAILABLE BY SPECIFYING WESTCOR CONNECTOR KIT P/N: 19-130044 WITH OPTIONAL BUS BAR DIMENSIONS SHOWN ARE FROM BOTTOM SURFACE. MOUNTING PEMNUTS EXTEND .010 PAST BOTTOM SURFACE 2 3 4 DESIGNATIONS MOTHER BOARD CONTROL BOARD SLOT NUMBER MODULE NUMBER FLOW 1.29 32,69 3 7.500 190,50 MOUNTING HOLES; 2 PLACES USE 8-32 X 0.25 or M4 X 6MM MAX LENGTH FROM OUTSIDE OF UNIT 10.650.02 270,460,51 10.40 264,11 7.500 190,50 AIR 10.24 260,02 0.16 4,09 MOUNTING HOLES; 2 PLACES USE 8-32 X 0.25 or M4 X 6MM MAX LENGTH FROM OUTSIDE OF UNIT 7.500 190,50 1.29 32,69 1.29 32,69 MBJ1 (5 PIN) MBJ1 A/C INPUT 2 MATING CONNECTOR: L1 HOUSING: MOLEX (39-01-4051) N/C TERMINAL: MOLEX (39-00-0090) L2/N CRIMP TOOL: MOLEX (11-01-0199) N/C GND PIN-1 CBJ3 (12 PIN) 1 NOTES: UNLESS OTHERWISE SPECIFIED 2 MATING CONNECTOR: HOUSING: MOLEX (50-57-9412) SOCKET CRIMP 24-30 AWG: MOLEX (16-02-0097) CRIMP TOOL: MOLEX (11-01-0209) 1 PFC MICRO 1 S2 SIX OUTPUT UNIT PICTURED (SEE PAGE 7 FOR DETAILED OUTPUT CONNECTION INFORMATION . ) MOUNTING HOLES; 4 PLACES USE 8-32 X 0.12 or M4 X 3MM MAX LENGTH FROM OUTSIDE OF UNIT 0.71 18,03 3.500 88,90 3 1 S1 5.06 128,52 4 1.86 47,29 0.250.02 6,350,51 1.22 31,04 4 4 1.22 31,04 LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM Mechanical Drawing, PFC Micro LoPACTM Family Page 7 of 9 SGND PGR ACOK N/C N/C N/C ED3 ED2 ED1 GSD PGDV Vcc Rev 2.5 02/2018 REFERENCE MB CB S(x) M(x) A COMPLETE SET OF MATING CONNECTORS IS AVAILABLE BY SPECIFYING WESTCOR CONNECTOR KIT P/N: 19-130044 DIMENSIONS SHOWN ARE FROM BOTTOM SURFACE. MOUNTING PEMNUTS EXTEND .010 PAST BOTTOM SURFACE. 2 3 DESIGNATIONS MOTHER BOARD CONTROL BOARD SLOT NUMBER MODULE NUMBER MBJ1 A/C INPUT 2 1.29 32,69 FLOW AIR 0.16 4,09 1.29 32,69 1.29 32,82 MATING CONNECTOR: L2/N HOUSING: MOLEX (39-01-4051) TERMINAL: MOLEX (39-00-0090) GND CRIMP TOOL: MOLEX (11-01-0199) L1 1 N/C PIN 1 MBJ1 (5 PIN) CBJ3 (12 PIN) N/C SIGNAL GROUND POWER GOOD/READ AC POWER OK N/C N/C N/C ENABLE/DISABLE S1M3 ENABLE/DISABLE S1M2 ENABLE/DISABLE S1M1 GENERAL SHUTDOWN POWER GOOD/DATA VALID +5V@40mA MATING CONNECTOR: HOUSING: MOLEX (50-57-9412) TERMINAL: MOLEX (16-02-0097) CRIMP TOOL: MOLEX (11-01-0209) CBJ3-1 CBJ3-2 CBJ3-3 CBJ3-4 CBJ3-5 CBJ3-6 CBJ3-7 CBJ3-8 CBJ3-9 CBJ3-10 CBJ3-11 CBJ3-12 CBJ3 E/D INTERFACE CONNECTOR PIN REF DESCRIPTION NOTES: UNLESS OTHERWISE SPECIFIED 2 1 PFC MICROS 5.100 129,54 MOUNTING HOLES; 2 PLACES USE 8-32 X 0.25 or M4 X 6MM MAX LENGTH FROM OUTSIDE OF UNIT 5.100 129,54 7.95 201,88 MOUNTING HOLES; 2 PLACES USE 8-32 X 0.25 or M4 X 6MM MAX LENGTH FROM OUTSIDE OF UNIT 5.100 129,54 1.22 31,04 3 MOUNTING HOLES 4 PLACES USE 8-32 X 0.12 or M4 X 3MM LENGTH FROM OUTSIDE OF UNIT 0.71 18,03 1 S1 3 1.86 47,29 3 5.06 128,52 3.500 88,90 1.22 31,04 TRIPLE OUTPUT UNIT PICTURED (SEE PAGE 7 FOR DETAILED OUTPUT CONNECTION INFORMATION). LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM Mechanical Drawing, PFC MicroS LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM Output Connections for the PFC Mini, PFC Micro and PFC MicroS A. OUTPUT STUDS - SINGLE OUTPUT (when populated with Full Brick modules) PFC Mini, PFC Micro and PFC MicroS -VOUT 10-32 OUTPUT STUDS SxJ2 REMOTE SENSE/TRIM PIN CONNECTOR 3 2 1 +VOUT MATING CONNECTOR: HOUSING: MOLEX (50-57-9403) TERMINAL FEMALE CRIMP 22-24 AWG: MOLEX (16-02-0103) USE CRIMP TOOL: MOLEX (11-01-0208) - REMOTE SENSE + REMOTE SENSE TRIM B. MOLEX CONNECTOR - SINGLE OR DUAL OUTPUT (when populated with Half Brick modules) PFC MINI 18 Pin Housing PFC MICRO 18 Pin Housing SxJ1 (18 PIN OUTPUT, REMOTE SENSE AND TRIM PIN CONNECTOR) SxJ1 (18 PIN OUTPUT, REMOTE SENSE AND TRIM PIN CONNECTOR) 9 18 8 17 7 16 6 15 5 14 4 13 3 12 2 11 1 10 PIN 1 2 3 4 5 6 7 8 9 DESCRIPTION + VOUT M2 - VOUT M2 - VOUT M2 + SENSE M2 - SENSE M2 TRIM M1 + VOUT M1 + VOUT M1 - VOUT M1 PIN 10 11 12 13 14 15 16 17 18 DESCRIPTION + VOUT M2 + VOUT M2 - VOUT M2 + SENSE M1 TRIM M2 - SENSE M1 + VOUT M1 - VOUT M1 - VOUT M1 9 18 8 17 7 16 6 15 5 14 4 13 3 12 2 11 1 10 PIN 1 2 3 4 5 6 7 8 9 DESCRIPTION + VOUT M1 - VOUT M1 - VOUT M1 + SENSE M1 - SENSE M1 TRIM M2 + VOUT M2 + VOUT M2 - VOUT M2 PIN 10 11 12 13 14 15 16 17 18 DESCRIPTION + VOUT M1 + VOUT M1 - VOUT M1 + SENSE M2 TRIM M1 - SENSE M2 + VOUT M2 - VOUT M2 - VOUT M2 MATING CONNECTOR: 18 PIN HOUSING: MOLEX (39-01-2180) TERMINAL FEMALE CRIMP 18-24 AWG: MOLEX 39-00-0039) USE CRIMP TOOL: MOLEX (11-01-0197) *PFC MicroS dual output slot configuration uses the type A stud connection for both outputs. 3-pin connector designators are S1J1 and S1J2. C. MOLEX CONNECTOR - SINGLE, DUAL OR TRIPLE OUTPUT (when populated with Quarter Brick modules) PFC Micro and PFC MicroS SxJ1 (16 PIN OUTPUT, REMOTE SENSE AND TRIM PIN CONNECTOR) 8 16 7 15 6 14 5 13 4 12 3 11 2 10 1 9 PIN 1 2 3 4 5 6 7 8 DESCRIPTION +VOUT M3 -VOUT M3 TRIM M3 +VOUT M2 -VOUT M2 TRIM M2 +VOUT M1 -VOUT M1 PIN 9 10 11 12 13 14 15 16 DESCRIPTION +VOUT M3 -VOUT M3 N/C +VOUT M2 -VOUT M2 TRIM M1 +VOUT M1 -VOUT M1 MATING CONNECTOR: 16 PIN HOUSING: MOLEX (39-01-2160) TERMINAL FEMALE CRIMP 18-24 AWG: MOLEX (39-00-0039) USE CRIMP TOOL: MOLEX (11-01-0197) LoPAC Accessories The following accessories are available for the LoPAC: Connector Kits Current-Share Boards A complete set of mating hardware for all combinations of input & output connections Used for current sharing between identical LoPAC Models for increased output power or redundancy * PFC Mini 19-130047 * LoPACs with VI-200TM/VI-J00TM Modules CSB01 * PFC Micro & PFC MicroS 19-130044 * LoPACs with Maxi, Mini, Micro Modules CSB02 LoPACTM Family Page 8 of 9 Rev 2.5 02/2018 LoPACTM PFC MiniTM, PFC MicroTM, PFC MicroSTM Vicor's comprehensive line of power solutions includes high density AC-DC and DC-DC modules and accessory components, fully configurable AC-DC and DC-DC power supplies, and complete custom power systems. Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its use. Vicor makes no representations or warranties with respect to the accuracy or completeness of the contents of this publication. Vicor reserves the right to make changes to any products, specifications, and product descriptions at any time without notice. Information published by Vicor has been checked and is believed to be accurate at the time it was printed; however, Vicor assumes no responsibility for inaccuracies. Testing and other quality controls are used to the extent Vicor deems necessary to support Vicor's product warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. Specifications are subject to change without notice. Visit http://www.vicorpower.com/lopac for the latest product information. Vicor's Standard Terms and Conditions and Product Warranty All sales are subject to Vicor's Standard Terms and Conditions of Sale, and Product Warranty which are available on Vicor's webpage (http://www.vicorpower.com/termsconditionswarranty) or upon request. Life Support Policy VICOR'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF VICOR CORPORATION. As used herein, life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. Per Vicor Terms and Conditions of Sale, the user of Vicor products and components in life support applications assumes all risks of such use and indemnifies Vicor against all liability and damages. Intellectual Property Notice Vicor and its subsidiaries own Intellectual Property (including issued U.S. and Foreign Patents and pending patent applications) relating to the products described in this data sheet. No license, whether express, implied, or arising by estoppel or otherwise, to any intellectual property rights is granted by this document. Interested parties should contact Vicor's Intellectual Property Department. Contact Us: http://www.vicorpower.com/contact-us Vicor Corporation 25 Frontage Road Andover, MA, USA 01810 Tel: 800-735-6200 Fax: 978-475-6715 www.vicorpower.com email Customer Service: custserv@vicorpower.com Technical Support: apps@vicorpower.com (c)2017 - 2018 Vicor Corporation. All rights reserved. The Vicor name is a registered trademark of Vicor Corporation. All other trademarks, product names, logos and brands are property of their respective owners. LoPACTM Family Page 9 of 9 Rev 2.5 02/2018