19-3772; Rev 1; 10/05 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors Applications Multivoltage Systems Networking Systems Telecom Internal Charge Pumps to Enhance External n-Channel FETs Capacitor-Adjustable Timeout Period Power-Good Output (MAX6880/MAX6882) Adjustable Undervoltage Lockout or Logic-Enable Input Internal 100 Pulldown for Each Output to Discharge Capacitive Load Quickly 0.5V to 5.5V Nominal IN_/OUT_ Range 2.7V to 5.5V Operating Voltage Range Immune to Short Voltage Transients Small 4mm x 4mm 24-Pin or 16-Pin Thin QFN Packages Ordering Information TEMP RANGE PINPACKAGE PKG CODE MAX6880ETG+ -40C to +85C 24 Thin QFN T2444-4 MAX6881ETE+ -40C to +85C 16 Thin QFN T1644-4 MAX6882ETE+ -40C to +85C 16 Thin QFN T1644-4 MAX6883ETE+ -40C to +85C 16 Thin QFN T1644-4 PART +Denotes lead-free package. N.C. PG/RST MARGIN TOP VIEW OUT3 Pin Configurations GATE3 The MAX6880-MAX6883 feature capacitor-adjustable slew-rate control to provide controlled turn-on characteristics. After all of the voltages reach 92.5% of their final value, a power-good output (MAX6880/MAX6882) signal is active. The power-good output (PG/RST) can be delayed with an external capacitor to create a power-on reset delay. After the initial power-up phase, the MAX6880-MAX6883 continue to monitor the voltages. If any of the voltages falls below its threshold, the MOSFETs are quickly turned off and the voltages are tracked down together. An internal 100 pulldown resistor ensures that the capacitance at the MOSFET's source is discharged quickly. The power-good output goes low to provide a system reset. The MAX6880-MAX6883 are available in small 4mm x 4mm 24-pin and 16-pin thin QFN packages and specified over the -40C to +85C extended operating temperature range. Capacitor-Adjustable Power-Up Sequencing Delay OUT2 The MAX6880-MAX6883 dual-/triple-voltage monitors are designed to sequence power supplies during power-up condition. When all of the voltages exceed their respective thresholds, these devices turn on voltages to the system sequentially, enhancing n-channel MOSFETs used as switches. The time between each sequenced voltage is determined by an external capacitor, thus allowing flexibility in delay timing. The MAX6880/MAX6881 sequence three voltages and the MAX6882/MAX6883 sequence two voltages. These devices initially monitor all of the voltages and when all of them are within their tolerances, the internal charge pumps enhance external n-channel MOSFETs in a sequential manner to apply the voltages to the system. Internal charge pumps drive the gate voltages 5V above the respective input voltage thereby ensuring the MOSFETs are fully enhanced to reduce the on-resistance. Features 18 17 16 15 14 13 GATE2 19 12 N.C. OUT1 20 11 N.C. 10 TIMEOUT 9 SLEW 8 DELAY 7 GND GATE1 21 MAX6880 IN3 22 EP* IN2 23 + Storage Equipment 1 2 3 4 5 6 ABP SET3 SET2 SET1 EN/UV IN1 24 N.C. Servers/Workstations 4mm x 4mm THIN QFN Selector Guide appears at end of data sheet. *EXPOSED PADDLE CONNECTED TO GND. Pin Configurations continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim's website at www.maxim-ic.com. 1 MAX6880-MAX6883 General Description MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors ABSOLUTE MAXIMUM RATINGS (All voltages referenced to GND, unless otherwise noted.) IN1, IN2, IN3.............................................................-0.3V to +6V ABP .........................................-0.3V to the highest of VIN1 - VIN3 SET1, SET2, SET3 ....................................................-0.3V to +6V GATE1, GATE2, GATE3 .........................................-0.3V to +12V OUT1, OUT2, OUT3 .................................................-0.3V to +6V MARGIN ...................................................................-0.3V to +6V PG/RST, EN/UV ........................................................-0.3V to +6V DELAY, SLEW, TIMEOUT .........................................-0.3V to +6V OUT_ Current....................................................................50mA GND Current.....................................................................50mA Input/Output Current (all pins except OUT_ and GND) ...........................................................20mA Continuous Power Dissipation (TA = +70C) 16-Pin 4mm x 4mm Thin QFN (derate 16.9mW/C above +70C) .............................1349mW 24-Pin 4mm x 4mm Thin QFN (derate 20.8mW/C above +70C) .............................1667mW Operating Temperature Range ...........................-40C to +85C Storage Temperature Range .............................-65C to +150C Maximum Junction Temperature .....................................+150C Lead Temperature (soldering, 10s) .................................+300C Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (IN1, IN2, or IN3 = +2.7V to +5.5V, EN/UV = MARGIN = ABP, TA = -40C to +85C, unless otherwise specified. Typical values are at TA = +25C, unless otherwise noted.) (Note 1) PARAMETER SYMBOL CONDITIONS Voltage on the highest of IN_ to ensure that PG/RST is valid and GATE_ = 0 Operating Voltage Range SET_ Threshold Range SET_ Threshold Hysteresis SET_ Input Current EN/UV Input Voltage MAX ICC VTH 1.4 2.7 IN1 = 5.5V, IN2 = IN3 = 3.3V, no load 5.5 1.1 1.8 SET_ falling, TA = +25oC 0.4925 0.5 0.5075 SET_ falling, TA = -40 C to +85C 0.4875 0.5 0.5125 VTH_HYST SET_ rising ISET SET_ = 0.5V VEN_R Input rising VEN_F Input falling IEN EN/UV Input Pulse Width tEN EN/UV falling, 100mV overdrive DELAY, TIMEOUT Output Current ID (Notes 2, 3) DELAY, TIMEOUT Threshold Voltage UNITS V EN/UV Input Current 0.5 -100 1.25 -5 VCC = 3.3V (Note 4) 22.5 Sequence Slew-Rate Timebase Accuracy SR CSLEW = 200pF -15 100pF < CSLEW < 1nF Slew-Rate Accuracy during PowerUp and Power-Down CSLEW = 200pF, VIN_ = 5.5V (Note 4) V nA V +5 A 2.88 A s 2.5 1.25 IS Timebase/CSLEW Ratio 1.28 7 2.12 mA % +100 1.286 1.22 SLEW Output Current 2 TYP IN_ Voltage on the highest of IN_ to ensure the device is fully operational Supply Current MIN 25 V 27.5 A +15 % 104 -50 _______________________________________________________________________________________ k +50 % Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors (IN1, IN2, or IN3 = +2.7V to +5.5V, EN/UV = MARGIN = ABP, TA = -40C to +85C, unless otherwise specified. Typical values are at TA = +25C, unless otherwise noted.) (Note 1) Power-Good Threshold Power-Good Threshold Hysteresis VTH_PG VOUT_ falling VHYS_PG VOUT_ rising 91.5 92.5 IN_ + 4.2 IN_ + 5.0 93.5 0.5 % % IN_ + 5.8 V GATE_ Output High VGOH ISOURCE = 0.5A GATE_ Pullup Current IGUP During power-up and power-down, VGATE_ = 1V 2.5 4 A IGD During power-up and power-down, VGATE_ = 5V 2.5 4 A GATE_ Pulldown Current IGDS SET_ to GATE_ Delay tD-GATE When disabled, VGATE_ = 5V, VIN_ 2.7V 9.5 When disabled, VGATE_ = 5V, VIN_ 4V 20 SET falling, 25mV overdrive 10 mA s VIN_ 2.7V, ISINK = 1mA, output asserted 0.3 VIN_ 4.0V, ISINK = 4mA, output asserted 0.4 V PG/RST Output Low VOL Tracking Differential Voltage Stop Ramp VTRK Differential between each of the OUT_ and the ramp voltage during power-up and power-down, Figure 1 (Note 5) 75 125 180 mV Tracking Differential Fault Voltage VTRK_F Differential between each of the OUT_ and the ramp voltage, Figure 1 (Note 5) 200 250 310 mV Power-Low Threshold VTH_PL OUT_ falling 125 142 170 mV Power-Low Hysteresis VTH_PLHYS OUT_ rising 10 IN_ > 2.7V (Note 6) 100 OUT to GND Pulldown Impedance MARGIN Pullup Current MARGIN Input Voltage MARGIN Glitch Rejection IIN 7 10 VIL VIH mV 13 0.8 2.0 100 A V ns Note 1: Specifications guaranteed for the stated global conditions. 100% production tested at TA = +25C and TA = +85C. Specifications at TA = -40C to +85C are guaranteed by design. These devices meet the parameters specified when at least one of IN1/IN2/IN3 is between 2.7V to 5.5V, while the remaining IN1/IN2/IN3 are between 0 and 5.5V. Note 2: A current ID = 2.5A 15% is generated internally and is used to set the DELAY and TIMEOUT periods and used as a reference for tDELAY and tTIMEOUT. Note 3: The total DELAY is tDELAY = 200s + (500k x CDELAY). Leave DELAY unconnected for 200s delay. The total TIMEOUT is tTIMEOUT = 200s + (500k x CTIMEOUT). Leave TIMEOUT unconnected for 200s timeout. Note 4: A current IS = 25A 10% is generated internally and used as a reference for tFAULT, tRETRY, and slew rate. Note 5: During power-up, only the condition OUT_ < ramp - VTRK is checked in order to stop the ramp. However, both conditions OUT_ < ramp - VTRK_F and OUT_ > ramp + VTRK_F cause a fault. During power-down, only the condition OUT > ramp + VTRK is checked in order to stop the ramp. However, both conditions OUT_ < ramp - VTRK_F and OUT_ > ramp + VTRK_F cause a fault (see Figure 10). Therefore, if OUT1, OUT2, and OUT3 (during power-up tracking and power-down) differ by more than 2 x VTRK_F, a fault condition is asserted. Note 6: A 100 pulldown to GND activated by a fault condition. See the Internal Pulldown section. _______________________________________________________________________________________ 3 MAX6880-MAX6883 ELECTRICAL CHARACTERISTICS (continued) MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors 125mV DOWN = STOP RAMP THRESHOLD 250mV UP = FAULT THRESHOLD 250mV UP = FAULT THRESHOLD 250mV DOWN = FAULT THRESHOLD 250mV DOWN = FAULT THRESHOLD 125mV UP = STOP RAMP THRESHOLD REFERENCE RAMP REFERENCE RAMP POWER-UP POWER-DOWN Figure 1. Stop Ramp/Fault Window During Power-Up and Power-Down EN/UV EN/UV BUS VOLTAGE MONITORED THROUGH EN/UV INPUT VEN_R VEN_F IN1 = 3.3V IN2 = 1.8V IN3 = 0.7V IN_ MONITORED THROUGH SET THRESHOLDS ON SET_ INPUTS CAPACITORADJUSTED SLEW RATE OUT1 = 3.3V OUT2 = 1.8V OUT_ OUT3 = 0.7V tDELAY PG/RST tDELAY tDELAY tTIMEOUT Figure 2. Sequencing In Normal Mode 4 _______________________________________________________________________________________ Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors MAX6880-MAX6883 EN/UV EN/UV BUS VOLTAGE MONITORED THROUGH EN/UV INPUT VEN_R IN1 = 3.3V IN2 = 1.8V IN_ IN3 = 0.7V MONITORED THROUGH SET THRESHOLDS ON SET_ INPUTS CAPACITORADJUSTED SLEW RATE OUT_ FORCED BELOW VTH_PG OUT1 = 3.3V OUT2 = 1.8V OUT_ OUT3 = 0.7V tDELAY tDELAY PG/RST tDELAY tTIMEOUT FORCED INTO QUICK SHUTDOWN WHEN OUT1 FALLS BELOW 92.5% of IN1 Figure 3. Sequencing In Fast Shutdown Mode _______________________________________________________________________________________ 5 MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors EN/UV EN/UV BUS VOLTAGE MONITORED THROUGH EN/UV INPUT VEN_R VEN_F IN1 = 3.3V IN2 = 1.8V IN3 = 0.7V IN_ MONITORED THROUGH SET THRESHOLDS ON SET_ INPUTS CAPACITORADJUSTED SLEW RATE OUT1 = 3.3V OUT2 = 1.8V OUT_ OUT3 = 0.7V tDELAY tDELAY tDELAY tTIMEOUT PG/RST = LOW Figure 4. Timing Diagram (Aborted Sequencing) EN/UV VEN_R OUT1 OUT1 OUT2 OUT2 OUT_ OUT3 IS SLOW OUT3 IS SLOW tDELAY tDELAY tFAULT tDELAY tDELAY tRETRY tFAULT tDELAY tDELAY tFAULT AND tRETRY NOT TO SCALE ALL SET > 0.5V AND IN_ 2.7V Figure 5. tFAULT and tRETRY Timing Diagram in Sequencing 6 _______________________________________________________________________________________ Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors (VIN_ = 2.7V to 5.5V, CSLEW = 200pF, EN = MARGIN = ABP, TA = +25C, unless otherwise noted.) VCC SUPPLY CURRENT vs. INPUT VOLTAGE NORMALIZED POWER-GOOD TIMEOUT vs. TEMPERATURE 1.1 TA = +25C TA = -40C 0.9 0.8 3.0 3.5 4.0 4.5 5.0 0.95 0.90 0.85 MAX6880 toc03 100 10 1 0.80 5.5 -40 -15 10 35 60 0.1 0.0001 85 0.001 0.01 0.1 INPUT VOLTAGE (V) TEMPERATURE (C) CDELAY (F) NORMALIZED SET_ THRESHOLD vs. TEMPERATURE NORMALIZED DELAY TIMEOUT vs. TEMPERATURE SLEW RATE vs. CSLEW 1.002 1.001 1.000 0.999 0.998 0.997 1.20 0.996 1.15 1.10 1.05 1.00 0.95 1 10,000 SLEW RATE (V/s) 1.003 1.25 MAX6880 toc05 1.004 NORMALIZED DELAY TIMEOUT MAX6880 toc04 1.005 0.90 1000 100 0.85 0.80 0.995 0.75 -15 10 35 60 85 10 -40 -15 10 35 60 85 100 1000 10,000 CSLEW (pF) DELAY TIMEOUT vs. CDELAY NORMALIZED EN/UV THRESHOLD vs. TEMPERATURE IN_ TRANSIENT DURATION vs. IN THRESHOLD OVERDRIVE 10 1 1.004 1.003 1.002 1.001 1.000 0.999 0.998 0.997 0.996 0.01 CDELAY (F) 0.1 1 IN_ = 3.3V 27 24 21 18 15 12 PG/RST GOES LOW ABOVE THE CURVE 9 6 3 0.995 0.001 30 IN_ TRANSIENT DURATION (s) MAX6880 toc07 100 1.005 MAX6880 toc09 TEMPERATURE (C) 1000 0.1 0.0001 10 TEMPERATURE (C) NORMALIZED EN_/UV THRESHOLD -40 MAX6880 toc08 NORMALIZED SET_ THRESHOLD 1.00 0.75 2.5 DELAY TIMEOUT (ms) 1.05 MAX6880 toc06 1.0 1.10 1000 POWER-GOOD TIMEOUT (ms) TA = +85C 1.2 MAX6880 toc02 1.3 1.15 NORMALIZED POWER-GOOD TIMEOUT MAX6880 toc01 VCC SUPPLY CURRENT (mA) 1.4 POWER-GOOD TIMEOUT vs. CTIMEOUT 0 -40 -15 10 35 TEMPERATURE (C) 60 85 0 50 100 150 200 250 300 IN_ THRESHOLD OVERDRIVE (mV) _______________________________________________________________________________________ 7 MAX6880-MAX6883 Typical Operating Characteristics Typical Operating Characteristics (continued) (VIN_ = 2.7V to 5.5V, CSLEW = 200pF, EN = MARGIN = ABP, TA = +25C, unless otherwise noted.) GATE_ VOLTAGE LOW vs. SINK CURRENT GATE_ OUTPUT VOLTAGE HIGH vs. GATE SOURCE CURRENT 1.4 9 8 GATE VOLTAGE (V) 1.2 1.0 0.8 0.6 SEQUENCING MODE MAX6880 toc12 MAX6880 toc11 10 MAX6880 toc10 1.6 GATE_ VOLTAGE LOW (V) MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors EN/UV 2V/div OUT1 1V/div 7 6 OUT2 1V/div OUT3 1V/div 5 4 3 0.4 2 0.2 1 0 0 0 1 2 3 4 5 6 7 8 9 10 0 GATE SINK CURRENT (mA) 0.5 1.0 1.5 2.0 2.5 20ms/div 3.0 GATE SOURCE CURRENT (A) FAST SHUTDOWN WITH RETRY FAST SHUTDOWN WITH RETRY MAX6880 toc13 MAX6880 toc14 EN/UV 2V/div OUT1 2V/div OUT2 2V/div OUT1 1V/div OUT3 PULLED BELOW 92.5% OF IN3 FOR SEQUENCING MODE OUT3 2V/div OUT2 1V/div OUT3 1V/div 40ms/div 8 PG/RST 1V/div 100ms/div _______________________________________________________________________________________ Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors PIN NAME FUNCTION MAX6880 MAX6881 MAX6882 MAX6883 1, 11, 12, 15 -- -- 1, 8, 9, 10 N.C. No Connection. Not internally connected. 2 -- 1 -- ABP Internal Supply Bypass Input. Bypass ABP with a 1F capacitor to GND. ABP maintains the device supply voltage during rapid powerdown conditions. 3 2 -- -- SET3 4 3 2 2 SET2 5 4 3 3 SET1 6 5 4 4 EN/UV 7 6 5 5 GND Externally Adjusted IN_ Undervoltage Lockout Threshold. Connect SET_ to an external resistor-divider network to set the desired undervoltage threshold for each IN_ supply (see the Typical Application Circuit). All SET_ inputs must be above the internal SET_ threshold (0.5V) to enable sequencing functionality. Logic-Enable Input or Undervoltage Lockout Monitor Input. EN/UV must be high (EN/UV > VEN_R) to enable voltage sequencing power-up operation. OUT_ begins tracking down when EN/UV < VEN_F. Connect EN/UV to an external resistor-divider network to set the external UVLO threshold. Ground 8 7 6 6 DELAY Sequence Delay Select Input. Connect a capacitor from DELAY to GND to select the desired delay period before sequencing is enabled (after all SET_ inputs and EN/UV are above their respective thresholds) or between supply sequences. Leave DELAY unconnected for the default 200s delay period. 9 8 7 7 SLEW Slew-Rate Adjustment Input. Connect a capacitor from SLEW to GND to select the desired OUT_ slew rate. 10 -- 8 -- 13 -- 9 -- PG/RST Timeout Period Adjust Input. PG/RST asserts high after the timeout period when all OUT_ exceed their IN_ referenced TIMEOUT threshold. Connect a capacitor from TIMEOUT to GND to set the desired timeout period. Leave TIMEOUT unconnected for the default 200s delay period. Margin Input, Active-Low. Drive MARGIN low to enable margin mode (see the Margin section). The MARGIN functionality is MARGIN disabled (returns to normal monitoring mode) after MARGIN returns high. MARGIN is internally pulled up to ABP through a 10A current source. _______________________________________________________________________________________ 9 MAX6880-MAX6883 Pin Description MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors Pin Description (continued) PIN NAME FUNCTION MAX6880 MAX6881 MAX6882 MAX6883 14 -- 10 -- PG/RST 16 9 -- -- OUT3 Channel 3 Monitored Output Voltage. Connect OUT3 to the source of an n-channel FET. A fault condition activates a 100 pulldown to ground. 17 10 -- -- GATE3 Gate Drive for External n-Channel FET. An internal charge pump boosts GATE3 to VIN3 + 5V to fully enhance the external n-channel FET when power-up is complete. 18 11 11 11 OUT2 Channel 2 Monitored Output Voltage. Connect OUT2 to the source of an n-channel FET. A fault condition activates a 100 pulldown to ground. 19 12 12 12 GATE2 Gate Drive for External n-Channel FET. An internal charge pump boosts GATE2 to VIN2 + 5V to fully enhance the external n-channel FET when power-up is complete. 20 13 13 13 OUT1 Channel 1 Monitored Output Voltage. Connect OUT1 to the source of an n-channel FET. A fault condition activates a 100 pulldown to ground. 21 14 14 14 GATE1 Gate Drive for External n-Channel FET. An internal charge pump boosts GATE1 to VIN1 + 5V to fully enhance the external n-channel FET when power-up is complete. 22 15 -- -- IN3 23 16 15 15 IN2 24 1 16 16 IN1 EP EP EP EP EP 10 Power-Good Output, Open-Drain. PG_RST asserts high tTIMEOUT after all OUT_ voltages exceed the VTH_PG thresholds. Supply Input Voltage. IN1, IN2, or IN3 must be greater than the internal undervoltage lockout (VABP = 2.7V) to enable the sequencing functionality. Each IN_ input is simultaneously monitored by SET_ inputs to ensure all supplies have stabilized before power-up is enabled. If IN_ is connected to ground or left unconnected and SET_ is above 0.5V, then no sequencing control is performed on that channel. Each IN_ is internally pulled down by a 100k resistor. Exposed Paddle. Connect exposed paddle to ground. ______________________________________________________________________________________ Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors IN1 TO LOAD IN2 IN3 IN1 OUT1 GATE1 ABP INTERNAL VCC/UVLO IN1 MAX6880 CHARGE PUMP SET1 RAMP GENERATOR IN2 COMP GATE CONTROLLER SET2 IN3 COMP CONTROL LOGIC IN2 TO OUT2 CONTROL BLOCK SET3 VBUS COMP GATE2 OUT2 OUT1 OUT2 SEQUENCING MONITOR EN/UV COMP OUT3 IN1 IN3 TO OUT3 CONTROL BLOCK GATE3 OUT3 IN2 IN3 VREF PG CIRCUIT MARGIN GND DELAY SLEW CSLEW TIMEOUT PG/RST CTIMEOUT ______________________________________________________________________________________ 11 MAX6880-MAX6883 Functional Diagram MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors Detailed Description The MAX6880-MAX6883 multivoltage power sequencers/supervisors monitor three (MAX6880/ MAX6881) and two (MAX6882/MAX6883) system voltages and provide proper power-up and power-down control for systems requiring voltage sequencing. These devices ensure the controlled voltages sequence in the proper order as system power supplies are enabled. The MAX6880-MAX6883 generate all required voltages and timing to control up to three external n-channel pass FETs for the OUT1/OUT2/OUT3 supply voltages. The MAX6880-MAX6883 feature adjustable undervoltage thresholds for each input supply. When all of the voltages are above the adjusted thresholds these devices turn on the external n-channel MOSFETs to sequence the voltages to the system. The outputs are turned on one after the other, OUT1 first and OUT3 last. The MAX6880-MAX6883 feature internal charge pumps to fully enhance the external FETs for low-voltage drops at highpass currents. The MAX6880/MAX6882 also feature a power-good output (PG/RST) with a selectable timeout period that can be used for system reset. The MAX6880-MAX6883 monitor up to three voltages. Devices may be configured to exclude any IN_. To disable sequencing operation of any IN_, connect the IN_ to ground (or leave unconnected) and connect SET_ to a voltage greater than 0.5V. The channel exclusion feature adds more flexibility to the device in a variety of different applications. As an example, the MAX6880 can sequence two voltages using IN1 and IN2 while IN3 is left disabled. Powering the MAX6880-MAX6883 These devices derive power from either IN1, IN2, or IN3 voltage inputs (see the Functional Diagram). In order to ensure proper operation, at least one of the IN_ inputs must be at least +2.7V. The highest input voltage on IN1/IN2/IN3 supplies power to the devices. Internal hysteresis ensures that the supply input that initially powers these devices continues to power the MAX6880-MAX6883 when multiple input voltages are within 100mV (typ) of each other. Sequencing The sequencing operation can be initiated after all input conditions for power-up are met VEN/UV > 1.25V and all SET_ inputs are above the internal SET_ threshold (0.5V). In sequencing mode, the outputs are turned on sequentially, OUT1 first and OUT3 last. Before turning on each channel, a delay period is waited (programmable by connecting a capacitor from DELAY to ground. The power-up phase for each channel ends 12 when its output voltage exceeds a fixed percentage (VTH_PG) of the corresponding IN_ voltage. When all channels have exceeded these thresholds, PG/RST asserts high after tTIMEOUT, indicating a successful sequence. If there is a fault condition during the initial power-up sequence, the process is aborted. When powering down, all outputs turn off simultaneously, tracking each other. No reverse power-down sequencing occurs. The power-supply sequencing operation should be completed within the selected fault timeout period (tFAULT) (see Figure 5). The total sequencing time is extended when the devices must vary the control slew rate to allow slow supplies to catch up. If the external FET is too small (RDS is too high for the selected load current and IN_ source current), the OUT_ voltage may never reach the control ramp voltage. For a slew rate of 935V/s, a fault is signaled if all outputs have not stabilized within 22ms. For a slew rate of 93.5V/s, a fault is signaled if sequencing takes too long (more than 219ms). The fault time period (tFAULT) is set through the capacitor at SLEW (CSLEW). Use the following formula to estimate the fault timeout period: tFAULT = 2.191 x 108 x CSLEW Autoretry Function The MAX6880/MAX6881/MAX6882 feature autoretry modes to power-on again after a fault condition has been detected (see the Typical Operating Characteristics). When a fault is detected, for a period of tRETRY, GATE_ remains off and the 100 pulldowns are turned on. After the tRETRY period, the device waits tDELAY and retry sequencing if all power-up conditions are met (see Figure 5). These include all VSET_ > 0.5V, EN/UV > VEN_R, and OUT_ voltages < VTH_PL. The autoretry period tRETRY is a function of CSLEW (see Table 1). Power-Up and Power-Down During power-up, OUT_ is forced to follow the internal reference ramp voltage by an internal loop that controls the GATE_ of the external MOSFET. This phase must be completed within the adjustable fault timeout period (tFAULT); otherwise, the part forces a shutdown on all GATE_. Once the power-up is completed, a power-down phase can be initiated by forcing VEN/UV below VEN_F. The reference voltage ramp ramps down at the capacitoradjusted slew rate. The control-loop comparators monitor each OUT_ voltage with respect to the common ______________________________________________________________________________________ Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors Internal Pulldown To ensure that the OUT_ voltages are not held high by a large output capacitance after a fault has occurred, there is a 100 internal pulldown at OUT_. The pulldown ensures that all OUT_ voltages are below VTH_PL (referenced to GND) before power-up cycling is initiated. The internal pulldown also ensures a fast discharge of the output capacitor during fast shutdown and fault modes. The pulldowns are not present during normal operation. Stability Comment No external compensation is required for sequencing or slew-rate control. Inputs IN1/IN2/IN3 The highest voltage on IN1, IN2, or IN3 supplies power to the device. The undervoltage threshold for each IN_ supply is set with an external resistor-divider from each IN_ to SET_ to ground. To disable sequencing on any IN_, connect IN_ to ground (or leave unconnected) and connect SET_ to a voltage greater than 0.5V. Undervoltage Lockout Threshold Inputs (SET_) The MAX6880/MAX6881 feature three and the MAX6882/ MAX6883 feature two externally adjustable IN_ undervoltage lockout thresholds (SET1/SET2/SET3). The 0.5V SET_ threshold enables monitoring IN_ voltages as low as 0.5V. The undervoltage threshold for each IN_ supply is set with an external resistor-divider from each IN_ to SET_ to ground (see Figure 6). All SET_ inputs must be above the internal SET_ threshold (0.5V) to enable sequencing functionality. Use the following formula to set the UVLO threshold: VIN_ = VTH (R1 + R2) / R2 where VIN_ is the undervoltage lockout threshold and VTH is the 500mV SET threshold. MARGIN) (MAX6880/MAX6882) Margin Input (M MARGIN allows system-level testing while power supplies are below the normal ranges as adjusted by the SET_ inputs. Drive MARGIN low before varying system voltages below the adjusted thresholds to avoid signaling an error. The state of PG/RST does not change while MARGIN is low. PG/RST and all monitoring functions are disabled while MARGIN is low. MARGIN makes it possible to vary the supplies without a need to adjust the thresholds to prevent sequencer alerts. Drive MARGIN high or leave it unconnected for normal operating mode. Slew-Rate Control Input (SLEW) The reference ramp voltage slew rate during any controlled power-up/down phase can be programmed in the 90V/s to 950V/s range by connecting a capacitor (CSLEW) from SLEW to ground. Use the following formula to calculate the typical slew rate: Slew Rate = (9.35 x 10-8)/ CSLEW where slew rate is in V/s and CSLEW is in farads. The capacitor at CSLEW also sets the retry timeout period (tRETRY), see Table 1. For example, if CSLEW = 100pF, we have tRETRY = 350ms, t FAULT = 21.91ms, slew rate = 935V/s. For example, if CSLEW = 1nF, we have tRETRY = 3.5s, slew rate = 93.5V/s. CSLEW is the capacitor on SLEW pad, and must be large enough so the parasitic PC board capacitance is negligible. CSLEW should be in the range of 100pF < CSLEW < 1nF. VIN_ IN_ R1 MAX6880- MAX6883 SET_ R2 Figure 6. Setting the Undervoltage (UVLO) Thresholds ______________________________________________________________________________________ 13 MAX6880-MAX6883 reference ramp voltage. During ramp down, if an OUT_ voltage is greater than the reference ramp voltage by more than VTRK, the control loop dynamically stops the control ramp voltage from decreasing until the slow OUT_ voltage catches up. If an OUT_ voltage is greater or less than the reference ramp voltage by more than VTRK_F, a fault is signaled and the fast-shutdown mode is initiated. In fast-shutdown mode, a 100 pulldown resistor is connected from OUT_ to GND to quickly discharge capacitance at OUT_, and GATE_ is pulled low with a strong IGDS current (see Figure 3). Figure 4 shows the aborted sequencing mode. When EN/UV goes low before tTIMEOUT expires, all the outputs go low, and the device goes into fast shutdown. MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors Table 1. CSLEW Timing Formulas TIME PERIOD FORMULAS Slew Rate (9.35 x 10-8) / CSLEW tRETRY 3.506 x 109 x CSLEW tFAULT 2.191 x 108 x CSLEW Limiting Inrush Current The capacitor (CSLEW) at SLEW to ground, controls the OUT_ slew rate, thus controlling the inrush current required to charge the load capacitor at OUT_. Using the programmed slew rate, limit the inrush current by using the following formula: IINRUSH = COUT x SR where IINRUSH is in amperes, COUT is in farads, and SR is in V/s. Delay Time Input (DELAY) To adjust the desired delay period (t DELAY ) before sequencing is enabled, connect a capacitor (CDELAY) between DELAY to ground (see Figures 2 to 5). The selected delay time is also enforced when EN/UV rises from low to high when all the input voltages are present. Use the following formula to calculate the delay time: tDELAY = 200s + (500k x CDELAY) where tDELAY is in s and CDELAY is in farads. Leave DELAY unconnected for the default 200s delay. Timeout Period Input (TIMEOUT) (MAX6880/MAX6882) These devices feature a PG/RST timeout period. Connect a capacitor (C TIMEOUT ) from TIMEOUT to ground to program the PG/RST timeout period. After all OUT_ outputs exceed their IN_ referenced thresholds (VTH_PG), PG/RST remains low for the selected timeout period tTIMEOUT (see Figure 3). tTIMEOUT = 200s + (500k x CTIMEOUT) where tTIMEOUT is in s and CTIMEOUT is in farads. Leave TIMEOUT unconnected for the default 200s timeout delay. UV) Logic-Enable Input (EN/U Drive logic EN/UV input above VEN_R to initiate voltage sequencing during power-up operation. Drive logic EN/UV below V EN_F to initiate tracking power-down operation. Connect EN/UV to an external resistordivider network to set the external undervoltage lockout threshold. 14 ABP Input (MAX6880/MAX6882) ABP powers the analog circuitry. Bypass ABP to GND with a 1F ceramic capacitor installed as close to the device as possible. ABP takes the highest voltage of IN_. Do not use ABP to provide power to external circuitry. ABP maintains the device supply voltage during rapid power-down conditions. OUT1/OUT2/OUT3 The MAX6880/MAX6881 monitor three OUT_ and the MAX6882/MAX6883 monitor two OUT_ outputs to control the sequencing performance. After the internal supply (ABP) exceeds the minimum voltage (2.7V) requirements, EN/UV > VEN_R, and IN1/IN2/IN3 are all greater than their adjusted SET_ thresholds, OUT1/ OUT2/OUT3 begin to sequence. During fault conditions, an internal pulldown resistor (100) on OUT_ is enabled to help discharge load capacitance (100 is connected for fast power-down control). Outputs GATE_ The MAX6880-MAX6883 feature up to three GATE_ outputs to drive up to three external n-channel FET gates. The following conditions must be met before GATE_ begins enhancing the external n-channel FET_: 1) All SET_ inputs (SET1/SET2/SET3) are above their 0.5V thresholds. 2) At least one IN_ input is above the minimum operating voltage (2.7V). 3) EN/UV > 1.25V. At power-up mode, GATE_ voltages are enhanced by control loops so all OUT_ voltages sequence at a capacitor-adjusted slew rate. Each GATE_ is internally pulled up to 5V above its relative IN_ voltage to fully enhance the external n-channel FET when power-up is complete. Power-Good Output (PG/RST) (MAX6880/MAX6882) The MAX6880/MAX6882 include a power-good (PG/RST) output. PG/RST is an open-drain output and requires an external pullup resistor. All the OUT_ outputs must exceed their IN_ referenced thresholds (IN_ x VTH_PG) for the selected reset timeout period tTIMEOUT (see the TIMEOUT Period Input section) before PG/RST asserts high. PG/RST stays low for the selected reset timeout period (tTIMEOUT) after all the OUT_ voltages exceed their IN_ referenced thresholds. PG/RST goes low when VSET_ < VTH or VEN/UV < VEN_R (see Figure 2). ______________________________________________________________________________________ Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors MOSFET Selection The external pass MOSFET is connected in series with the sequenced power-supply source. Since the load current and the MOSFET drain-to-source impedance (RDS) determine the voltage drop, the on characteristics of the MOSFET affect the load supply accuracy. The MAX6880-MAX6883 fully enhance the external MOSFET out of its linear range to ensure the lowest drain-to-source on-impedance. For highest supply accuracy/lowest voltage drop, select a MOSFET with an appropriate drain-to-source on-impedance with a gate-to-source bias of 4.5V to 6.0V. Layout and Bypassing For better noise immunity, bypass each of the IN_ inputs to GND with 0.1F capacitors installed as close to the device as possible. Bypass ABP to GND with a 1F capacitor installed as close to the device as possible. ABP is an internally generated voltage and must not be used to supply power to external circuitry. Selector Guide PART CHANNEL TIMEOUT SELECTABLE PG/RST MARGIN PG THRESHOLD VOLTAGE (%) MAX6880 3 Yes Yes Yes 92.5 MAX6881 3 No No No -- MAX6882 2 Yes Yes Yes 92.5 MAX6883 2 No No No -- Chip Information PROCESS: BiCMOS ______________________________________________________________________________________ 15 MAX6880-MAX6883 Applications Information Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors MAX6880-MAX6883 Typical Application Circuit IN1 OUT1 IN2 OUT2 IN3 OUT3 0.1F IN1 IN2 0.1F 0.1F IN3 SET1 GATE1 GATE2 GATE3 OUT1 SET2 OUT2 MAX6880 SET3 OUT3 VBUS EN/UV PG/RST MARGIN ABP SLEW GND DELAY TIMEOUT 1F 16 ______________________________________________________________________________________ Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors GATE2 OUT2 GATE3 OUT3 GATE2 OUT2 PG/RST MARGIN TOP VIEW 12 11 10 9 12 11 10 9 OUT1 13 8 SLEW OUT1 13 8 TIMEOUT GATE1 14 7 DELAY GATE1 14 7 SLEW 6 GND 6 DELAY 5 GND MAX6881 IN3 15 MAX6882 IN2 15 EP* EP* 4 SET3 SET2 SET1 1 2 3 4 EN/UV 3 + SET1 2 IN1 16 SET2 1 EN/UV ABP 5 + IN1 IN2 16 4mm x 4mm THIN QFN GATE2 OUT2 N.C. N.C. 4mm x 4mm THIN QFN 12 11 10 9 OUT1 13 8 N.C. GATE1 14 7 SLEW 6 DELAY 5 GND MAX6883 IN2 15 EP* 1 2 3 4 SET2 SET1 EN/UV + N.C. IN1 16 4mm x 4mm THIN QFN *EXPOSED PADDLE CONNECTED TO GND. ______________________________________________________________________________________ 17 MAX6880-MAX6883 Pin Configurations (continued) Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) 24L QFN THIN.EPS MAX6880-MAX6883 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors PACKAGE OUTLINE, 12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm 21-0139 18 ______________________________________________________________________________________ E 1 2 Dual-/Triple-Voltage, Power-Supply Sequencers/Supervisors PACKAGE OUTLINE, 12, 16, 20, 24, 28L THIN QFN, 4x4x0.8mm 21-0139 E 2 2 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 19 (c) 2005 Maxim Integrated Products Heaney Printed USA is a registered trademark of Maxim Integrated Products, Inc. MAX6880-MAX6883 Package Information (continued) (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.)