PWM Controller and Transformer Driver with Quad-Channel Isolators ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 FEATURES FUNCTIONAL BLOCK DIAGRAMS Isolated PWM controller Integrated transformer driver Regulated adjustable output: 3.3 V to 24 V 2 W output power 70% efficiency at guaranteed load of 400 mA at 5.0 V output Quad dc-to-25 Mbps (NRZ) signal isolation channels 20-lead SSOP package High temperature operation: 105C maximum High common-mode transient immunity: >25 kV/s 200 kHz to 1 MHz adjustable oscillator frequency Soft start function at power-up Pulse-by-pulse overcurrent protection Thermal shutdown Safety and regulatory approvals UL recognition: 2500 V rms for 1 minute per UL 1577 CSA Component Acceptance Notice #5A VDE certificate of conformity DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 VIORM = 560 V peak Qualified for automotive applications T1 X1 VDDA VISO RECT VDD1 DRIVER VREG X2 ADuM3470/ADuM3471/ ADuM3472/ADuM3473/ ADuM3474 PRIMARY CONVERTER REG 5V SECONDARY CONTROLLER VIB/VOB CH B PRIMARY DATA I/O 4CH VIC/VOC CH C FB OC CH A VIA/VOA VDD2 FB SECONDARY DATA I/O 4CH VIA/VOA VIB/VOB VIC/VOC CH D VID/VOD VID/VOD GND2 GND1 09369-001 Data Sheet Figure 1. Functional Block Diagram ADuM3470 ADuM3471 APPLICATIONS RS-232/RS-422/RS-485 transceivers Industrial field bus isolation Power supply start-up bias and gate drives Isolated sensor interfaces Process controls Automotive ADuM3472 GENERAL DESCRIPTION ADuM3473 ADuM3474 09369-003 The ADuM3470/ADuM3471/ADuM3472/ADuM3473/ ADuM3474 devices1 are quad-channel digital isolators with an integrated PWM controller and transformer driver for an isolated dc-to-dc converter. Based on the Analog Devices, Inc., iCoupler(R) technology, the dc-to-dc converter provides up to 2 W of regulated, isolated power at 3.3 V to 24 V from a 5.0 V input supply or from a 3.3 V supply. This eliminates the need for a separate, isolated dc-to-dc converter in 2 W isolated designs. The iCoupler chip scale transformer technology is used to isolate the logic signals, and the integrated transformer driver with isolated secondary side control provides higher efficiency for the isolated dc-to-dc converter. The result is a small form factor, total isolation solution. The ADuM347x isolators provide four independent isolation channels in a variety of channel configurations and data rates (see the Ordering Guide). Figure 2. Block Diagrams of I/O Channels 1 Protected by U.S. Patents 5,952,849; 6,873,065; and 7,075,329. Other patents pending. Rev. B Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2010-2014 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Data Sheet TABLE OF CONTENTS Features .............................................................................................. 1 Typical Performance Characteristics ........................................... 19 Applications ....................................................................................... 1 Terminology .................................................................................... 24 General Description ......................................................................... 1 Applications Information .............................................................. 25 Functional Block Diagrams ............................................................. 1 Application Schematics ............................................................. 25 Revision History ............................................................................... 2 Transformer Design ................................................................... 26 Specifications..................................................................................... 3 Transformer Turns Ratio ........................................................... 26 Electrical Characteristics--5 V Primary Input Supply/ 5 V Secondary Isolated Supply ................................................... 3 Transformer ET Constant ......................................................... 27 Electrical Characteristics--3.3 V Primary Input Supply/ 3.3 V Secondary Isolated Supply ................................................ 5 Transformer Isolation Voltage .................................................. 27 Electrical Characteristics--5 V Primary Input Supply/ 3.3 V Secondary Isolated Supply ................................................ 7 Transient Response .................................................................... 27 Transformer Primary Inductance and Resistance ................. 27 Switching Frequency .................................................................. 27 Electrical Characteristics--5 V Primary Input Supply/ 15 V Secondary Isolated Supply ................................................. 9 Component Selection ................................................................ 27 Package Characteristics ............................................................. 11 Thermal Analysis ....................................................................... 28 Regulatory Approvals................................................................. 11 Propagation Delay-Related Parameters ................................... 28 Insulation and Safety-Related Specifications .......................... 11 DC Correctness and Magnetic Field Immunity ..................... 29 DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 Insulation Characteristics.......................................................... 12 Power Consumption .................................................................. 30 Recommended Operating Conditions .................................... 12 Insulation Lifetime ..................................................................... 31 Absolute Maximum Ratings.......................................................... 13 Outline Dimensions ....................................................................... 32 ESD Caution ................................................................................ 13 Ordering Guide .......................................................................... 33 Pin Configurations and Function Descriptions ......................... 14 Automotive Products ................................................................. 33 Printed Circuit Board (PCB) Layout ....................................... 28 Power Considerations ................................................................ 30 REVISION HISTORY 5/14--Rev. A to Rev. B Change to Table 4 ............................................................................. 9 7/13--Rev. 0 to Rev. A Changed VDD1 Pin to NC Pin ....................................... Throughout Changes to Features Section, Applications Section, General Description Section, and Figure 1 ................................... 1 Created Hyperlink for Safety and Regulatory Approvals Entry in Features Section................................................................. 1 Changes to Table 1 ............................................................................ 3 Changes to Table 2 ............................................................................ 5 Changes to Table 3 ............................................................................ 7 Changes to Table 4 ............................................................................ 9 Changes to Regulatory Approvals Section .................................. 11 Changes to Figure 3 and Table 9 ................................................... 12 Changes to Figure 4 and Table 12 ................................................. 14 Changes to Figure 5 and Table 13 ................................................. 15 Changes to Figure 6 and Table 14................................................. 16 Changes to Figure 7 and Table 15................................................. 17 Changes to Figure 8, Table 16, and Table 17 ............................... 18 Change to Figure 9 ......................................................................... 19 Changes to Terminology Section ................................................. 24 Changes to Applications Information Section, Application Schematics Section, Figure 38, Figure 39, and Figure 40 .......... 25 Changes to Transformer Turns Ratio Section ............................ 26 Changes to Transformer ET Constant Section, Transient Response Section, and Table 19 .................................. 27 Changes to Figure 41...................................................................... 28 Changes to Power Consumption Section and Figure 45........... 30 Changes to Insulation Lifetime Section and Figure 48 ............. 31 Changes to Ordering Guide .......................................................... 33 Added Automotive Products Section .......................................... 33 10/10--Revision 0: Initial Version Rev. B | Page 2 of 36 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 SPECIFICATIONS ELECTRICAL CHARACTERISTICS--5 V PRIMARY INPUT SUPPLY/5 V SECONDARY ISOLATED SUPPLY 4.5 V VDD1 = VDDA 5.5 V; VDD2 = VREG = VISO = 5.0 V; fSW = 500 kHz; all voltages are relative to their respective grounds (see the application schematic in Figure 38). All minimum/maximum specifications apply over the entire recommended operating range, unless otherwise noted. All typical specifications are at TA = 25C, VDD1 = VDDA = 5.0 V, VDD2 = VREG = VISO = 5.0 V. Table 1. Parameter DC-TO-DC CONVERTER POWER SUPPLY Isolated Output Voltage Feedback Voltage Setpoint Line Regulation Load Regulation Output Ripple Symbol Min Typ Max Unit Test Conditions/Comments VISO VFB VISO (LINE) VISO (LOAD) VISO (RIP) 4.5 1.125 5.0 1.25 1 1 50 5.5 1.375 10 2 V V mV/V % mV p-p IISO = 0 mA, VISO = VFB x (R1 + R2)/R2 IISO = 0 mA IISO = 50 mA, VDD1 = 4.5 V to 5.5 V IISO = 50 mA to 200 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA ROC = 50 k ROC = 270 k VOC = VDD2 (open loop) Output Noise VISO (N) 100 mV p-p Switching Frequency fSW RON 1000 200 318 0.5 kHz kHz kHz VUV+ VUV- VUVH 2.8 2.6 0.2 192 Switch On Resistance Undervoltage Lockout, VDD1, VDD2 Supplies Positive Going Threshold Negative Going Threshold Hysteresis DC to 2 Mbps Data Rate 1 Maximum Output Supply Current 2 Efficiency at Maximum Output Supply Current 3 iCOUPLER DATA CHANNELS DC to 2 Mbps Data Rate1 IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 25 Mbps Data Rate (C Grade Only) IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 Available VISO Supply Current 4 ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 IDD1 Supply Current, Full VISO Load IISO (MAX) 515 V V V 400 mA % 70 IDD1 (Q) IISO = 0 mA, f 1 MHz 14 15 16 17 18 30 30 30 30 30 mA mA mA mA mA IDD1 (D) IISO = 0 mA, CL = 15 pF, f = 12.5 MHz 44 46 48 50 52 mA mA mA mA mA 390 388 386 384 382 550 mA mA mA mA mA mA IISO (LOAD) IDD1 (MAX) f 1 MHz VISO = 5.0 V IISO = IISO (MAX) CL = 15 pF, f = 12.5 MHz Rev. B | Page 3 of 36 CL = 0 pF, f = 0 MHz, VDD1 = 5 V, IISO = 400 mA ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Parameter I/O Input Currents Logic High Input Threshold Logic Low Input Threshold Logic High Output Voltages Logic Low Output Voltages AC SPECIFICATIONS A Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Propagation Delay Skew Channel-to-Channel Matching C Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Change vs. Temperature Propagation Delay Skew Channel-to-Channel Matching Codirectional Channels Opposing Directional Channels Output Rise/Fall Time (10% to 90%) Common-Mode Transient Immunity At Logic High Output At Logic Low Output Refresh Rate Symbol IIA, IIB, IIC, IID VIH VIL VOAH, VOBH, VOCH, VODH Min -20 2.0 Typ +0.01 VDD1 - 0.3, VISO - 0.3 VDD1 - 0.5, VISO - 0.5 Max +20 5.0 Unit A V V V IOx = -20 A, VIx = VIxH 4.8 V IOx = -4 mA, VIx = VIxH 0.8 VOAL, VOBL, VOCL, VODL Data Sheet Test Conditions/Comments 0.0 0.1 V IOx = 20 A, VIx = VIxL 0.0 0.4 V IOx = 4 mA, VIx = VIxL 1000 ns Mbps ns ns ns ns CL = 15 pF, CMOS signal levels PW 1 tPHL, tPLH PWD tPSK tPSKCD/tPSKOD 55 100 40 50 50 CL = 15 pF, CMOS signal levels PW tPHL, tPLH PWD 40 25 30 45 60 8 5 tPSK 15 tPSKCD tPSKOD tR/tF 8 15 |CMH| |CML| fr 25 25 ns Mbps ns ns ps/C ns 2.5 ns ns ns 35 35 1.0 kV/s kV/s Mbps CL = 15 pF, CMOS signal levels VCM = 1000 V, transient magnitude = 800 V VIx = VDD1 or VISO VIx = 0 V The contributions of supply current values for all four channels are combined at identical data rates. The VISO supply current is available for external use when all data rates are below 2 Mbps. At data rates above 2 Mbps, the data I/O channels draw additional current proportional to the data rate. Additional supply current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. The dynamic I/O channel load must be treated as an external load and included in the VISO power budget. 3 The power demands of the quiescent operation of the data channels is not separated from the power supply section. Efficiency includes the quiescent power consumed by the I/O channels as part of the internal power consumption. 4 This current is available for driving external loads at the VISO output. All channels are simultaneously driven at a maximum data rate of 25 Mbps with full capacitive load representing the maximum dynamic load conditions. Refer to the Power Consumption section for calculation of the available current at less than the maximum data rate. 1 2 Rev. B | Page 4 of 36 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 ELECTRICAL CHARACTERISTICS--3.3 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY 3.0 V VDD1 = VDDA 3.6 V; VDD2 = VREG = VISO = 3.3 V; fSW = 500 kHz; all voltages are relative to their respective grounds (see the application schematic in Figure 38). All minimum/maximum specifications apply over the entire recommended operating range, unless otherwise noted. All typical specifications are at TA = 25C, VDD1 = VDDA = 3.3 V, VDD2 = VREG = VISO = 3.3 V. Table 2. Parameter DC-TO-DC CONVERTER POWER SUPPLY Isolated Output Voltage Feedback Voltage Setpoint Line Regulation Load Regulation Output Ripple Symbol Min Typ Max Unit Test Conditions/Comments VISO VFB VISO (LINE) VISO (LOAD) VISO (RIP) 3.0 1.125 3.3 1.25 1 1 50 3.6 1.375 10 2 V V mV/V % mV p-p IISO = 0 mA, VISO = VFB x (R1 + R2)/R2 IISO = 0 mA IISO = 50 mA, VDD1 = 3.0 V to 3.6 V IISO = 20 mA to 100 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA ROC = 50 k ROC = 270 k VOC = VDD2 (open loop) Output Noise VISO (N) 100 mV p-p Switching Frequency fSW RON 1000 200 318 0.6 kHz kHz kHz VUV+ VUV- VUVH 2.8 2.6 0.2 V V V 70 mA % 192 Switch On Resistance Undervoltage Lockout, VDD1, VDD2 Supplies Positive Going Threshold Negative Going Threshold Hysteresis DC to 2 Mbps Data Rate 1 Maximum Output Supply Current 2 Efficiency at Maximum Output Supply Current 3 iCOUPLER DATA CHANNELS DC to 2 Mbps Data Rate1 IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 25 Mbps Data Rate (C Grade Only) IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 Available VISO Supply Current 4 ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 IDD1 Supply Current, Full VISO Load I/O Input Currents IISO (MAX) 515 250 IDD1 (Q) IISO = 0 mA, f 1 MHz 9 10 11 11 12 20 20 20 20 20 mA mA mA mA mA IDD1 (D) IISO = 0 mA, CL = 15 pF, f = 12.5 MHz 28 29 31 32 34 mA mA mA mA mA 244 243 241 240 238 350 mA mA mA mA mA mA IISO (LOAD) CL = 15 pF, f = 12.5 MHz IDD1 (MAX) IIA, IIB, IIC, IID f 1 MHz, VISO = 3.3 V IISO = IISO (MAX) -10 +0.01 Rev. B | Page 5 of 36 +10 A CL = 0 pF, f = 0 MHz, VDD1 = 3.3 V, IISO = 250 mA ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Parameter Logic High Input Threshold Logic Low Input Threshold Logic High Output Voltages Logic Low Output Voltages AC SPECIFICATIONS A Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Propagation Delay Skew Channel-to-Channel Matching C Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Change vs. Temperature Propagation Delay Skew Channel-to-Channel Matching Codirectional Channels Opposing Directional Channels Output Rise/Fall Time (10% to 90%) Common-Mode Transient Immunity At Logic High Output At Logic Low Output Refresh Rate Symbol VIH VIL VOAH, VOBH, VOCH, VODH Min 1.6 Typ VDD1 - 0.3, VISO - 0.3 VDD1 - 0.5, VISO - 0.5 Max 5.0 Unit V V V IOx = -20 A, VIx = VIxH 4.8 V IOx = -4 mA, VIx = VIxH 0.4 VOAL, VOBL, VOCL, VODL Data Sheet Test Conditions/Comments 0.0 0.1 V IOx = 20 A, VIx = VIxL 0.0 0.4 V IOx = 4 mA, VIx = VIxL 1000 ns Mbps ns ns ns ns CL = 15 pF, CMOS signal levels PW 1 tPHL, tPLH PWD tPSK tPSKCD/tPSKOD 60 100 40 50 50 CL = 15 pF, CMOS signal levels PW tPHL, tPLH PWD 40 25 30 60 75 8 5 tPSK 45 tPSKCD tPSKOD tR/tF 8 15 |CMH| |CML| fr 25 25 ns Mbps ns ns ps/C ns 2.5 ns ns ns 35 35 1.0 kV/s kV/s Mbps CL = 15 pF, CMOS signal levels VCM = 1000 V, transient magnitude = 800 V VIx = VDD1 or VISO VIx = 0 V The contributions of supply current values for all four channels are combined at identical data rates. The VISO supply current is available for external use when all data rates are below 2 Mbps. At data rates above 2 Mbps, the data I/O channels draw additional current proportional to the data rate. Additional supply current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. The dynamic I/O channel load must be treated as an external load and included in the VISO power budget. 3 The power demands of the quiescent operation of the data channels is not separated from the power supply section. Efficiency includes the quiescent power consumed by the I/O channels as part of the internal power consumption. 4 This current is available for driving external loads at the VISO output. All channels are simultaneously driven at a maximum data rate of 25 Mbps with full capacitive load representing the maximum dynamic load conditions. Refer to the Power Consumption section for calculation of the available current at less than the maximum data rate. 1 2 Rev. B | Page 6 of 36 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 ELECTRICAL CHARACTERISTICS--5 V PRIMARY INPUT SUPPLY/3.3 V SECONDARY ISOLATED SUPPLY 4.5 V VDD1 = VDDA 5.5 V; VDD2 = VREG = VISO = 3.3 V; fSW = 500 kHz; all voltages are relative to their respective grounds (see the application schematic in Figure 38). All minimum/maximum specifications apply over the entire recommended operating range, unless otherwise noted. All typical specifications are at TA = 25C, VDD1 = VDDA = 5.0 V, VDD2 = VREG = VISO = 3.3 V. Table 3. Parameter DC-TO-DC CONVERTER POWER SUPPLY Isolated Output Voltage Feedback Voltage Setpoint Line Regulation Load Regulation Output Ripple Symbol Min Typ Max Unit Test Conditions/Comments VISO VFB VISO (LINE) VISO (LOAD) VISO (RIP) 3.0 1.125 3.3 1.25 1 1 50 3.6 1.375 10 2 V V mV/V % mV p-p IISO = 0 mA, VISO = VFB x (R1 + R2)/R2 IISO = 0 mA IISO = 50 mA, VDD1 = 4.5 V to 5.5 V IISO = 50 mA to 200 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA ROC = 50 k ROC = 270 k VOC = VDD2 (open loop) Output Noise VISO (N) 100 mV p-p Switching Frequency fSW RON 1000 200 318 0.5 kHz kHz kHz VUV+ VUV- VUVH 2.8 2.6 0.2 V V V 70 mA % 192 Switch On Resistance Undervoltage Lockout, VDD1, VDD2 Supplies Positive Going Threshold Negative Going Threshold Hysteresis DC to 2 Mbps Data Rate 1 Maximum Output Supply Current 2 Efficiency at Maximum Output Supply Current 3 iCOUPLER DATA CHANNELS DC to 2 Mbps Data Rate1 IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 25 Mbps Data Rate (C Grade Only) IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 Available VISO Supply Current 4 ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 IDD1 Supply Current, Full VISO Load I/O Input Currents IISO (MAX) 515 400 IDD1 (Q) IISO = 0 mA, f 1 MHz 9 9 10 10 10 30 30 30 30 30 mA mA mA mA mA IDD1 (D) IISO = 0 mA, CL = 15 pF, f = 12.5 MHz 33 33 33 33 33 mA mA mA mA mA 393 392 390 389 388 375 mA mA mA mA mA mA IISO (LOAD) CL = 15 pF, f = 12.5 MHz IDD1 (MAX) IIA, IIB, IIC, IID f 1 MHz VISO = 3.3 V IISO = IISO (MAX) -20 +0.01 Rev. B | Page 7 of 36 +20 A CL = 0 pF, f = 0 MHz, VDD1 = 5 V, IISO = 400 mA ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Parameter Logic High Input Threshold Logic Low Input Threshold Logic High Output Voltages Logic Low Output Voltages AC SPECIFICATIONS A Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Propagation Delay Skew Channel-to-Channel Matching C Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Change vs. Temperature Propagation Delay Skew Channel-to-Channel Matching Codirectional Channels Opposing Directional Channels Output Rise/Fall Time (10% to 90%) Common-Mode Transient Immunity At Logic High Output At Logic Low Output Refresh Rate Symbol VIH VIL VOAH, VOBH, VOCH, VODH Min 2.0 Typ VDD1 - 0.3, VISO - 0.3 VDD1 - 0.5, VISO - 0.5 Max 5.0 Unit V V V IOx = -20 A, VIx = VIxH 4.8 V IOx = -4 mA, VIx = VIxH 0.8 VOAL, VOBL, VOCL, VODL Data Sheet Test Conditions/Comments 0.0 0.1 V IOx = 20 A, VIx = VIxL 0.0 0.4 V IOx = 4 mA, VIx = VIxL 1000 ns Mbps ns ns ns ns CL = 15 pF, CMOS signal levels PW 1 tPHL, tPLH PWD tPSK tPSKCD/tPSKOD 55 100 40 50 50 CL = 15 pF, CMOS signal levels PW tPHL, tPLH PWD 40 25 30 50 70 8 5 tPSK 15 tPSKCD tPSKOD tR/tF 8 15 |CMH| |CML| fr 25 25 ns Mbps ns ns ps/C ns 2.5 ns ns ns 35 35 1.0 kV/s kV/s Mbps CL = 15 pF, CMOS signal levels VCM = 1000 V, transient magnitude = 800 V VIx = VDD1 or VISO VIx = 0 V The contributions of supply current values for all four channels are combined at identical data rates. The VISO supply current is available for external use when all data rates are below 2 Mbps. At data rates above 2 Mbps, the data I/O channels draw additional current proportional to the data rate. Additional supply current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. The dynamic I/O channel load must be treated as an external load and included in the VISO power budget. 3 The power demands of the quiescent operation of the data channels is not separated from the power supply section. Efficiency includes the quiescent power consumed by the I/O channels as part of the internal power consumption. 4 This current is available for driving external loads at the VISO output. All channels are simultaneously driven at a maximum data rate of 25 Mbps with full capacitive load representing the maximum dynamic load conditions. Refer to the Power Consumption section for calculation of the available current at less than the maximum data rate. 1 2 Rev. B | Page 8 of 36 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 ELECTRICAL CHARACTERISTICS--5 V PRIMARY INPUT SUPPLY/15 V SECONDARY ISOLATED SUPPLY 4.5 V VDD1 = VDDA 5.5 V; VREG = VISO = 15 V; VDD2 = 5.0 V; fSW = 500 kHz; all voltages are relative to their respective grounds (see the application schematic in Figure 39). All minimum/maximum specifications apply over the entire recommended operating range, unless otherwise noted. All typical specifications are at TA = 25C, VDD1 = VDDA = 5.0 V, VREG = VISO = 15 V, VDD2 = 5.0 V. Table 4. Parameter DC-TO-DC CONVERTER POWER SUPPLY Isolated Output Voltage Feedback Voltage Setpoint VDD2 Linear Regulator Regulator Voltage Symbol Min Typ Max Unit Test Conditions/Comments VISO VFB 13.5 1.125 15 1.25 16.5 1.375 V V IISO = 0 mA, VISO = VFB x (R1 + R2)/R2 IISO = 0 mA VDD2 4.6 5.0 5.7 V 1.5 20 3 V mV/V % mV p-p VREG = 7 V to 15 V, IDD2 = 0 mA to 50 mA IDD2 = 50 mA IISO = 50 mA, VDD1 = 4.5 V to 5.5 V IISO = 20 mA to 100 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA 20 MHz bandwidth, COUT = 0.1 F||47 F, IISO = 100 mA ROC = 50 k ROC = 270 k VOC = VDD2 (open loop) Dropout Voltage Line Regulation Load Regulation Output Ripple VDD2 (DO) VISO (LINE) VISO (LOAD) VISO (RIP) 0.5 1 1 200 Output Noise VISO (N) 500 mV p-p Switching Frequency fSW RON 1000 200 318 0.5 kHz kHz kHz VUV+ VUV- VUVH 2.8 2.6 0.2 V V V 70 mA % 192 Switch On Resistance Undervoltage Lockout, VDD1, VDD2 Supplies Positive Going Threshold Negative Going Threshold Hysteresis DC to 2 Mbps Data Rate 1 Maximum Output Supply Current 2 Efficiency at Maximum Output Supply Current 3 iCOUPLER DATA CHANNELS DC to 2 Mbps Data Rate1 IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 25 Mbps Data Rate (C Grade Only) IDD1 Supply Current, No VISO Load ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 Available VISO Supply Current 4 ADuM3470 ADuM3471 ADuM3472 ADuM3473 ADuM3474 IDD1 Supply Current, Full VISO Load IISO (MAX) 515 100 IDD1 (Q) IISO = 0 mA, f 1 MHz 25 27 29 31 33 45 45 45 45 45 mA mA mA mA mA IDD1 (D) IISO = 0 mA, CL = 15 pF, f = 12.5 MHz 73 83 93 102 112 mA mA mA mA mA 91 89 86 83 80 425 mA mA mA mA mA mA IISO (LOAD) IDD1 (MAX) f 1 MHz VISO = 5.0 V IISO = IISO (MAX) CL = 15 pF, f = 12.5 MHz Rev. B | Page 9 of 36 CL = 0 pF, f = 0 MHz, VDD1 = 5 V, IISO = 100 mA ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Parameter I/O Input Currents Logic High Input Threshold Logic Low Input Threshold Logic High Output Voltages Logic Low Output Voltages AC SPECIFICATIONS A Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Propagation Delay Skew Channel-to-Channel Matching C Grade Minimum Pulse Width Maximum Data Rate Propagation Delay Pulse Width Distortion, |tPLH - tPHL| Change vs. Temperature Propagation Delay Skew Channel-to-Channel Matching Codirectional Channels Opposing Directional Channels Output Rise/Fall Time (10% to 90%) Common-Mode Transient Immunity At Logic High Output At Logic Low Output Refresh Rate Symbol IIA, IIB, IIC, IID VIH VIL VOAH, VOBH, VOCH, VODH Min -20 2.0 Typ +0.01 VDD1 - 0.3, VISO - 0.3 VDD1 - 0.5, VISO - 0.5 Max +20 5.0 Unit A V V V IOx = -20 A, VIx = VIxH 4.8 V IOx = -4 mA, VIx = VIxH 0.8 VOAL, VOBL, VOCL, VODL Data Sheet Test Conditions/Comments 0.0 0.1 V IOx = 20 A, VIx = VIxL 0.0 0.4 V IOx = 4 mA, VIx = VIxL 1000 ns Mbps ns ns ns ns CL = 15 pF, CMOS signal levels PW 1 tPHL, tPLH PWD tPSK tPSKCD/tPSKOD 55 100 40 50 50 CL = 15 pF, CMOS signal levels PW tPHL, tPLH PWD 40 25 30 45 60 8 5 tPSK 15 tPSKCD tPSKOD tR/tF 8 15 |CMH| |CML| fr 25 25 ns Mbps ns ns ps/C ns 2.5 ns ns ns 35 35 1.0 kV/s kV/s Mbps CL = 15 pF, CMOS signal levels VCM = 1000 V, transient magnitude = 800 V VIx = VDD1 or VISO VIx = 0 V The contributions of supply current values for all four channels are combined at identical data rates. The VISO supply current is available for external use when all data rates are below 2 Mbps. At data rates above 2 Mbps, the data I/O channels draw additional current proportional to the data rate. Additional supply current associated with an individual channel operating at a given data rate can be calculated as described in the Power Consumption section. The dynamic I/O channel load must be treated as an external load and included in the VISO power budget. 3 The power demands of the quiescent operation of the data channels is not separated from the power supply section. Efficiency includes the quiescent power consumed by the I/O channels as part of the internal power consumption. 4 This current is available for driving external loads at the VISO output. All channels are simultaneously driven at a maximum data rate of 25 Mbps with full capacitive load representing the maximum dynamic load conditions. Refer to the Power Consumption section for calculation of the available current at less than the maximum data rate. 1 2 Rev. B | Page 10 of 36 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 PACKAGE CHARACTERISTICS Table 5. Parameter RESISTANCE AND CAPACITANCE Resistance (Input to Output) 1 Capacitance (Input to Output)1 Input Capacitance 2 IC Junction to Ambient Thermal Resistance THERMAL SHUTDOWN Thermal Shutdown Threshold Thermal Shutdown Hysteresis Symbol Min Typ Max Unit RI-O CI-O CI JA 1012 2.2 4.0 50.5 pF pF C/W TSSD TSSD-HYS 150 20 C C Test Conditions/Comments f = 1 MHz Thermocouple is located at the center of the package underside; test conducted on a 4-layer board with thin traces 3 TJ rising The device is considered a 2-terminal device: Pin 1 to Pin 10 are shorted together, and Pin 11 to Pin 20 are shorted together. Input capacitance is from any input data pin to ground. 3 See the Thermal Analysis section for thermal model definitions. 1 2 REGULATORY APPROVALS The ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 are approved by the organizations listed in Table 6. Refer to Table 11 and the Insulation Lifetime section for more information about the recommended maximum working voltages for specific cross-insulation waveforms and insulation levels. Table 6. UL Recognized under the UL 1577 component recognition program 1 Single protection, 2500 V rms isolation voltage File E214100 CSA Approved under CSA Component Acceptance Notice #5A Basic insulation per CSA 60950-1-03 and IEC 60950-1, 600 V rms (848 V peak) maximum working voltage File 205078 VDE Certified according to DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 2 Reinforced insulation, 560 V peak File 2471900-4880-0001 In accordance with UL 1577, each ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 is proof tested by applying an insulation test voltage of 3000 V rms for 1 sec (current leakage detection limit = 10 A). 2 In accordance with DIN V VDE V 0884-10 (VDE V 0884-10):2006-12, each ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 is proof tested by applying an insulation test voltage of 1050 V peak for 1 sec (partial discharge detection limit = 5 pC). The asterisk (*) marking branded on the component designates DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 approval. 1 INSULATION AND SAFETY-RELATED SPECIFICATIONS Table 7. Parameter Rated Dielectric Insulation Voltage Minimum External Air Gap (Clearance) Symbol L(I01) Value 2500 >5.1 Unit V rms mm Minimum External Tracking (Creepage) L(I02) >5.1 mm Minimum Internal Distance (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group CTI 0.017 min >400 II mm V Rev. B | Page 11 of 36 Test Conditions/Comments 1-minute duration Measured from input terminals to output terminals, shortest distance through air Measured from input terminals to output terminals, shortest distance path along body Distance through insulation DIN IEC 112/VDE 0303, Part 1 Material Group (DIN VDE 0110, 1/89, Table 1) ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Data Sheet DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 INSULATION CHARACTERISTICS These isolators are suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by protective circuits. The asterisk (*) marking branded on the component denotes DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 approval. Table 8. Description Installation Classification per DIN VDE 0110 For Rated Mains Voltage 150 V rms For Rated Mains Voltage 300 V rms For Rated Mains Voltage 400 V rms Climatic Classification Pollution Degree per DIN VDE 0110, Table 1 Maximum Working Insulation Voltage Input-to-Output Test Voltage, Method B1 Test Conditions/Comments VIORM x 1.875 = VPR, 100% production test, tm = 1 sec, partial discharge < 5 pC Input-to-Output Test Voltage, Method A After Environmental Tests Subgroup 1 After Input and/or Safety Tests Subgroup 2 and Subgroup 3 Highest Allowable Overvoltage Safety Limiting Values Symbol Characteristic Unit VIORM VPR I to IV I to III I to II 40/105/21 2 560 1050 V peak V peak 896 672 V peak V peak VTR 4000 V peak TS IS1 RS 150 1.25 >109 C A VPR VIORM x 1.6 = VPR, tm = 60 sec, partial discharge < 5 pC VIORM x 1.2 = VPR, tm = 60 sec, partial discharge < 5 pC Transient overvoltage, tTR = 10 sec Maximum value allowed in the event of a failure (see Figure 3) Case Temperature Side 1 Current Insulation Resistance at TS VIO = 500 V 1.25 1.00 0.75 0.50 0.25 0 0 50 100 150 CASE TEMPERATURE (C) 200 09369-002 SAFE OPERATING VDD1 CURRENT (A) 1.50 Figure 3. Thermal Derating Curve, Dependence of Safety Limiting Values on Case Temperature, per DIN EN 60747-5-2 RECOMMENDED OPERATING CONDITIONS Table 9. Parameter Operating Temperature Supply Voltages 1 VDD1 at VISO = 3.3 V VDD1 at VISO = 5.0 V VDD1 at VISO = 5.0 V Minimum Load 1 Symbol TA Min -40 Max +105 Unit C VDD1 VDD1 VDD1 IISO (MIN) 3.0 3.0 4.5 10 3.6 3.6 5.5 V V V mA All voltages are relative to their respective grounds. Rev. B | Page 12 of 36 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 ABSOLUTE MAXIMUM RATINGS Ambient temperature = 25C, unless otherwise noted. Table 11. Maximum Continuous Working Voltage Supporting 50-Year Minimum Lifetime1 Table 10. Parameter Storage Temperature Range (TST) Ambient Operating Temperature Range (TA) Supply Voltages1 VDD1,2 VDDA, VDD2 VREG, X1, X2 Input Voltage (VIA, VIB, VIC, VID)1, 3 Output Voltage (VOA, VOB, VOC, VOD)1, 3 Average Output Current per Pin4 Common-Mode Transients5 Rating -55C to +150C -40C to +105C -0.5 V to +7.0 V -0.5 V to +20.0 V -0.5 V to VDDI + 0.5 V -0.5 V to VDDO + 0.5 V -10 mA to +10 mA -100 kV/s to +100 kV/s All voltages are relative to their respective grounds. VDD1 is the power supply for the push-pull transformer. VDDI and VDDO refer to the supply voltages on the input and output sides of a given channel, respectively. See the Printed Circuit Board (PCB) Layout section. 4 See Figure 3 for maximum rated current values for various temperatures. 5 Refers to common-mode transients across the insulation barrier. Commonmode transients exceeding the absolute maximum ratings may cause latch-up or permanent damage. 1 2 3 Parameter AC Voltage, Bipolar Waveform AC Voltage, Unipolar Waveform Basic Insulation DC Voltage Basic Insulation 1 Applicable Certification All certifications Max 565 Unit V peak 848 V peak Working voltage per IEC 60950-1 848 V peak Working voltage per IEC 60950-1 Refers to the continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for more information. ESD CAUTION Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Rev. B | Page 13 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Data Sheet X1 1 20 VREG *GND1 2 19 GND2* NC 3 18 VDD2 X2 4 ADuM3470 17 FB VIA 5 TOP VIEW (Not to Scale) 16 VOA 15 VOB VIC 7 14 VOC VID 8 13 VOD VDDA 9 12 OC *GND1 10 11 GND2* VIB 6 NOTES 1. NC = NO INTERNAL CONNECTION. 2. PIN 2 AND PIN 10 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. 09369-004 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS Figure 4. ADuM3470 Pin Configuration Table 12. ADuM3470 Pin Function Descriptions Pin No. 1 2, 10 Mnemonic X1 GND1 3 4 5 6 7 8 9 11, 19 NC X2 VIA VIB VIC VID VDDA GND2 12 OC 13 14 15 16 17 VOD VOC VOB VOA FB 18 VDD2 20 VREG Description Transformer Driver Output 1. Ground Reference for the Primary Side of the Isolator. Pin 2 and Pin 10 are internally connected to each other; it is recommended that both pins be connected to a common ground. No Internal Connection. Transformer Driver Output 2. Logic Input A. Logic Input B. Logic Input C. Logic Input D. Supply Voltage for the Primary Side, 3.0 V to 5.5 V. Connect a 0.1 F bypass capacitor from VDDA to GND1. Ground Reference for the Secondary Side of the Isolator. Pin 11 and Pin 19 are internally connected to each other; it is recommended that both pins be connected to a common ground. Oscillator Control Pin. When the OC pin is connected high to the VDD2 pin, the secondary controller runs in openloop (unregulated) mode. To regulate the output voltage, connect a resistor between the OC pin and GND2; the secondary controller runs at a frequency of 200 kHz to 1 MHz, as programmed by the resistor value. Logic Output D. Logic Output C. Logic Output B. Logic Output A. Feedback Input from the Secondary Output Voltage, VISO. Use a resistor divider from the VISO output to the FB pin to set the VFB voltage equal to the 1.25 V internal reference level using the formula VISO = VFB x (R1 + R2)/R2. The resistor divider is required even in open-loop mode to provide soft start. Internal Supply Voltage for the Secondary Side Controller and the Side 2 Data Channels. When a sufficient external voltage is supplied to VREG, the internal regulator regulates the VDD2 pin to 5.0 V. Otherwise, VDD2 should be in the 3.0 V to 5.5 V range. Connect a 0.1 F bypass capacitor from VDD2 to GND2. Input of the Internal Regulator to Power the Secondary Side Controller and the Side 2 Data Channels. VREG should be in the 5.5 V to 15 V range to regulate the VDD2 output to 5.0 V. Rev. B | Page 14 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 X1 1 20 VREG *GND1 2 19 GND2* NC 3 18 VDD2 X2 4 ADuM3471 17 FB VIA 5 TOP VIEW (Not to Scale) 16 VOA VIB 6 VIC 7 15 VOB 14 VOC VOD 8 13 VID VDDA 9 12 OC *GND1 10 11 GND2* NOTES 1. NC = NO INTERNAL CONNECTION. 2. PIN 2 AND PIN 10 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. 09369-005 Data Sheet Figure 5. ADuM3471 Pin Configuration Table 13. ADuM3471 Pin Function Descriptions Pin No. 1 2, 10 Mnemonic X1 GND1 3 4 5 6 7 8 9 11, 19 NC X2 VIA VIB VIC VOD VDDA GND2 12 OC 13 14 15 16 17 VID VOC VOB VOA FB 18 VDD2 20 VREG Description Transformer Driver Output 1. Ground Reference for the Primary Side of the Isolator. Pin 2 and Pin 10 are internally connected to each other; it is recommended that both pins be connected to a common ground. No Internal Connection. Transformer Driver Output 2. Logic Input A. Logic Input B. Logic Input C. Logic Output D. Supply Voltage for the Primary Side, 3.0 V to 5.5 V. Connect a 0.1 F bypass capacitor from VDDA to GND1. Ground Reference for the Secondary Side of the Isolator. Pin 11 and Pin 19 are internally connected to each other; it is recommended that both pins be connected to a common ground. Oscillator Control Pin. When the OC pin is connected high to the VDD2 pin, the secondary controller runs in openloop (unregulated) mode. To regulate the output voltage, connect a resistor between the OC pin and GND2; the secondary controller runs at a frequency of 200 kHz to 1 MHz, as programmed by the resistor value. Logic Input D. Logic Output C. Logic Output B. Logic Output A. Feedback Input from the Secondary Output Voltage, VISO. Use a resistor divider from the VISO output to the FB pin to set the VFB voltage equal to the 1.25 V internal reference level using the formula VISO = VFB x (R1 + R2)/R2. The resistor divider is required even in open-loop mode to provide soft start. Internal Supply Voltage for the Secondary Side Controller and the Side 2 Data Channels. When a sufficient external voltage is supplied to VREG, the internal regulator regulates the VDD2 pin to 5.0 V. Otherwise, VDD2 should be in the 3.0 V to 5.5 V range. Connect a 0.1 F bypass capacitor from VDD2 to GND2. Input of the Internal Regulator to Power the Secondary Side Controller and the Side 2 Data Channels. VREG should be in the 5.5 V to 15 V range to regulate the VDD2 output to 5.0 V. Rev. B | Page 15 of 36 X1 1 20 VREG *GND1 2 19 GND2* NC 3 18 VDD2 X2 4 ADuM3472 17 FB VIA 5 TOP VIEW (Not to Scale) 16 VOA 15 VOB VOC 7 14 VIC VOD 8 13 VID VDDA 9 12 OC *GND1 10 11 GND2* VIB 6 NOTES 1. NC = NO INTERNAL CONNECTION. 2. PIN 2 AND PIN 10 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. Data Sheet 09369-006 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Figure 6. ADuM3472 Pin Configuration Table 14. ADuM3472 Pin Function Descriptions Pin No. 1 2, 10 Mnemonic X1 GND1 3 4 5 6 7 8 9 11, 19 NC X2 VIA VIB VOC VOD VDDA GND2 12 OC 13 14 15 16 17 VID VIC VOB VOA FB 18 VDD2 20 VREG Description Transformer Driver Output 1. Ground Reference for the Primary Side of the Isolator. Pin 2 and Pin 10 are internally connected to each other; it is recommended that both pins be connected to a common ground. No Internal Connection. Transformer Driver Output 2. Logic Input A. Logic Input B. Logic Output C. Logic Output D. Supply Voltage for the Primary Side, 3.0 V to 5.5 V. Connect a 0.1 F bypass capacitor from VDDA to GND1. Ground Reference for the Secondary Side of the Isolator. Pin 11 and Pin 19 are internally connected to each other; it is recommended that both pins be connected to a common ground. Oscillator Control Pin. When the OC pin is connected high to the VDD2 pin, the secondary controller runs in openloop (unregulated) mode. To regulate the output voltage, connect a resistor between the OC pin and GND2; the secondary controller runs at a frequency of 200 kHz to 1 MHz, as programmed by the resistor value. Logic Input D. Logic Input C. Logic Output B. Logic Output A. Feedback Input from the Secondary Output Voltage, VISO. Use a resistor divider from the VISO output to the FB pin to set the VFB voltage equal to the 1.25 V internal reference level using the formula VISO = VFB x (R1 + R2)/R2. The resistor divider is required even in open-loop mode to provide soft start. Internal Supply Voltage for the Secondary Side Controller and the Side 2 Data Channels. When a sufficient external voltage is supplied to VREG, the internal regulator regulates the VDD2 pin to 5.0 V. Otherwise, VDD2 should be in the 3.0 V to 5.5 V range. Connect a 0.1 F bypass capacitor from VDD2 to GND2. Input of the Internal Regulator to Power the Secondary Side Controller and the Side 2 Data Channels. VREG should be in the 5.5 V to 15 V range to regulate the VDD2 output to 5.0 V. Rev. B | Page 16 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 X1 1 20 VREG *GND1 2 19 GND2* NC 3 18 VDD2 X2 4 ADuM3473 17 FB VIA 5 TOP VIEW (Not to Scale) 16 VOA 15 VIB VOC 7 14 VIC VOD 8 13 VID VDDA 9 12 OC *GND1 10 11 GND2* VOB 6 NOTES 1. NC = NO INTERNAL CONNECTION. 2. PIN 2 AND PIN 10 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. 09369-007 Data Sheet Figure 7. ADuM3473 Pin Configuration Table 15. ADuM3473 Pin Function Descriptions Pin No. 1 2, 10 Mnemonic X1 GND1 3 4 5 6 7 8 9 11, 19 NC X2 VIA VOB VOC VOD VDDA GND2 12 OC 13 14 15 16 17 VID VIC VIB VOA FB 18 VDD2 20 VREG Description Transformer Driver Output 1. Ground Reference for the Primary Side of the Isolator. Pin 2 and Pin 10 are internally connected to each other; it is recommended that both pins be connected to a common ground. No Internal Connection. Transformer Driver Output 2. Logic Input A. Logic Output B. Logic Output C. Logic Output D. Supply Voltage for the Primary Side, 3.0 V to 5.5 V. Connect a 0.1 F bypass capacitor from VDDA to GND1. Ground Reference for the Secondary Side of the Isolator. Pin 11 and Pin 19 are internally connected to each other; it is recommended that both pins be connected to a common ground. Oscillator Control Pin. When the OC pin is connected high to the VDD2 pin, the secondary controller runs in openloop (unregulated) mode. To regulate the output voltage, connect a resistor between the OC pin and GND2; the secondary controller runs at a frequency of 200 kHz to 1 MHz, as programmed by the resistor value. Logic Input D. Logic Input C. Logic Input B. Logic Output A. Feedback Input from the Secondary Output Voltage, VISO. Use a resistor divider from the VISO output to the FB pin to set the VFB voltage equal to the 1.25 V internal reference level using the formula VISO = VFB x (R1 + R2)/R2. The resistor divider is required even in open-loop mode to provide soft start. Internal Supply Voltage for the Secondary Side Controller and the Side 2 Data Channels. When a sufficient external voltage is supplied to VREG, the internal regulator regulates the VDD2 pin to 5.0 V. Otherwise, VDD2 should be in the 3.0 V to 5.5 V range. Connect a 0.1 F bypass capacitor from VDD2 to GND2. Input of the Internal Regulator to Power the Secondary Side Controller and the Side 2 Data Channels. VREG should be in the 5.5 V to 15 V range to regulate the VDD2 output to 5.0 V. Rev. B | Page 17 of 36 X1 1 20 VREG *GND1 2 19 GND2* NC 3 18 VDD2 X2 4 ADuM3474 17 FB VOA 5 TOP VIEW (Not to Scale) 16 VIA 15 VIB VOC 7 14 VIC VOD 8 13 VID VDDA 9 12 OC *GND1 10 11 GND2* VOB 6 NOTES 1. NC = NO INTERNAL CONNECTION. 2. PIN 2 AND PIN 10 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. PIN 11 AND PIN 19 ARE INTERNALLY CONNECTED TO EACH OTHER; IT IS RECOMMENDED THAT BOTH PINS BE CONNECTED TO A COMMON GROUND. Data Sheet 09369-008 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Figure 8. ADuM3474 Pin Configuration Table 16. ADuM3474 Pin Function Descriptions Pin No. 1 2, 10 Mnemonic X1 GND1 3 4 5 6 7 8 9 11, 19 NC X2 VOA VOB VOC VOD VDDA GND2 12 OC 13 14 15 16 17 VID VIC VIB VIA FB 18 VDD2 20 VREG Description Transformer Driver Output 1. Ground Reference for the Primary Side of the Isolator. Pin 2 and Pin 10 are internally connected to each other; it is recommended that both pins be connected to a common ground. No Internal Connection. Transformer Driver Output 2. Logic Output A. Logic Output B. Logic Output C. Logic Output D. Supply Voltage for the Primary Side, 3.0 V to 5.5 V. Connect a 0.1 F bypass capacitor from VDDA to GND1. Ground Reference for the Secondary Side of the Isolator. Pin 11 and Pin 19 are internally connected to each other; it is recommended that both pins be connected to a common ground. Oscillator Control Pin. When the OC pin is connected high to the VDD2 pin, the secondary controller runs in openloop (unregulated) mode. To regulate the output voltage, connect a resistor between the OC pin and GND2; the secondary controller runs at a frequency of 200 kHz to 1 MHz, as programmed by the resistor value. Logic Input D. Logic Input C. Logic Input B. Logic Input A. Feedback Input from the Secondary Output Voltage, VISO. Use a resistor divider from the VISO output to the FB pin to set the VFB voltage equal to the 1.25 V internal reference level using the formula VISO = VFB x (R1 + R2)/R2. The resistor divider is required even in open-loop mode to provide soft start. Internal Supply Voltage for the Secondary Side Controller and the Side 2 Data Channels. When a sufficient external voltage is supplied to VREG, the internal regulator regulates the VDD2 pin to 5.0 V. Otherwise, VDD2 should be in the 3.0 V to 5.5 V range. Connect a 0.1 F bypass capacitor from VDD2 to GND2. Input of the Internal Regulator to Power the Secondary Side Controller and the Side 2 Data Channels. VREG should be in the 5.5 V to 15 V range to regulate the VDD2 output to 5.0 V. Table 17. Truth Table (Positive Logic) VIx Input1 High Low 1 VDD1 State Powered Powered VDD2 State Powered Powered VOxOutput1 High Low VIx and VOx refer to the input and output signals of a given channel (A, B, C, or D). Rev. B | Page 18 of 36 Notes Normal operation, data is high Normal operation, data is low Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 TYPICAL PERFORMANCE CHARACTERISTICS 1500 1400 80 1300 70 1200 60 1100 EFFICIENCY (%) fSW (kHz) 1000 900 800 700 600 500 400 50 40 30 20 300 -40C +25C +105C 10 100 100 150 200 250 300 350 400 450 500 ROC (k) 0 70 70 60 60 EFFICIENCY (%) 80 50 40 30 50 100 150 200 250 300 350 400 450 500 LOAD CURRENT (mA) Figure 10. Typical Efficiency at Various Switching Frequencies with Coilcraft Transformer, 5 V Input to 5 V Output 0 EFFICIENCY (%) 50 40 30 350 400 450 500 LOAD CURRENT (mA) 09369-011 300 100 150 200 250 300 350 400 450 500 50 40 30 1MHz 700kHz 500kHz 200kHz 10 0 250 50 20 1MHz 700kHz 500kHz 200kHz 200 500 Figure 13. Single-Supply Efficiency with Coilcraft Transformer, fSW = 500 kHz 60 150 450 LOAD CURRENT (mA) 60 100 400 VDD1 = 5V, VISO = 5V VDD1 = 5V, VISO = 3.3V VDD1 = 3.3V, VISO = 3.3V 0 70 50 350 30 70 0 300 40 80 10 250 50 80 20 200 10 0 0 150 20 1MHz 700kHz 500kHz 200kHz 10 100 Figure 12. Typical Efficiency over Temperature with Coilcraft Transformer, fSW = 500 kHz, 5 V Input to 5 V Output 80 20 50 LOAD CURRENT (mA) 09369-010 EFFICIENCY (%) Figure 9. Switching Frequency (fSW) vs. ROC Resistance EFFICIENCY (%) 0 09369-013 50 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 LOAD CURRENT (mA) Figure 14. Typical Efficiency at Various Switching Frequencies with Coilcraft Transformer, 5 V Input to 15 V Output Figure 11. Typical Efficiency at Various Switching Frequencies with Halo Transformer, 5 V Input to 5 V Output Rev. B | Page 19 of 36 09369-014 0 09369-009 0 09369-012 200 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 80 Data Sheet 15 70 10 ICH (mA) 50 40 30 5 1MHz 700kHz 500kHz 200kHz 10 0 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 LOAD CURRENT (mA) VDD1 = 5V, VISO = 5V VDD1 = 5V, VISO = 3.3V VDD1 = 3.3V, VISO = 3.3V 0 Figure 15. Typical Efficiency at Various Switching Frequencies with Halo Transformer, 5 V Input to 15 V Output 0 5 10 15 20 25 DATA RATE (Mbps) 09369-029 20 09369-026 EFFICIENCY (%) 60 Figure 18. Typical Single-Supply ICH Supply Current per Forward Data Channel (15 pF Output Load) 15 80 70 10 50 ICH (mA) EFFICIENCY (%) 60 40 30 5 20 0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 LOAD CURRENT (mA) 0 09369-027 0 Figure 16. Typical Efficiency over Temperature with Coilcraft Transformer, fSW = 500 kHz, 5 V Input to 15 V Output 0 5 10 20 25 Figure 19. Typical Single-Supply ICH Supply Current per Reverse Data Channel (15 pF Output Load) 80 5 VDD1 = 5V, VISO = 5V VDD1 = 5V, VISO = 3.3V VDD1 = 3.3V, VISO = 3.3V 70 4 60 50 IISO (D) (mA) EFFICIENCY (%) 15 DATA RATE (Mbps) 09369-030 VDD1 = 5V, VISO = 5V VDD1 = 5V, VISO = 3.3V VDD1 = 3.3V, VISO = 3.3V -40C +25C +105C 10 40 30 3 2 20 1 10 10 20 30 40 50 60 70 80 90 100 110 120 130 140 LOAD CURRENT (mA) Figure 17. Double-Supply Efficiency with Coilcraft Transformer, fSW = 500 kHz Rev. B | Page 20 of 36 0 0 5 10 15 20 25 DATA RATE (Mbps) Figure 20. Typical Single-Supply IISO (D) Dynamic Supply Current per Output Channel (15 pF Output Load) 09369-031 0 09369-028 VDD1 = 5V, VISO = 15V VDD1 = 5V, VISO = 12V 0 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 5 5 4 IISO (D) (mA) 4 3 2 3 2 1 1 0 5 10 15 20 25 DATA RATE (Mbps) 0 09369-032 0 0 5 10 15 20 25 DATA RATE (Mbps) Figure 21. Typical Single-Supply IISO (D) Dynamic Supply Current per Input Channel 09369-035 IISO (D) (mA) VDD1 = 5V, V ISO = 15V VDD1 = 5V, V ISO = 12V VDD1 = 5V, VISO = 5V VDD1 = 5V, VISO = 3.3V VDD1 = 3.3V, VISO = 3.3V Figure 24. Typical Double-Supply IISO (D) Dynamic Supply Current per Output Channel (15 pF Output Load) 5 30 VDD1 = 5V, V ISO = 15V VDD1 = 5V, V ISO = 12V VDD1 = 5V, V ISO = 15V VDD1 = 5V, V ISO = 12V 25 4 IISO (D) (mA) ICH (mA) 20 15 3 2 10 0 5 10 15 20 25 DATA RATE (Mbps) 0 09369-033 0 0 10 15 20 25 DATA RATE (Mbps) Figure 22. Typical Double-Supply ICH Supply Current per Forward Data Channel (15 pF Output Load) Figure 25. Typical Double-Supply IISO (D) Dynamic Supply Current per Input Channel 30 6 VDD1 = 5V, V ISO = 15V VDD1 = 5V, V ISO = 12V 25 5 4 15 3 10 2 5 1 0 5 10 15 DATA RATE (Mbps) 20 25 0 09369-034 0 Figure 23. Typical Double-Supply ICH Supply Current per Reverse Data Channel (15 pF Output Load) VISO AT 10mA VISO AT 50mA VISO AT 400mA 0 5 10 15 TIME (ms) 20 25 30 09369-037 VISO (V) 20 ICH (mA) 5 09369-036 1 5 Figure 26. Typical VISO Startup with 10 mA, 50 mA, and 400 mA Output Load, 5 V Input to 5 V Output Rev. B | Page 21 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 6.0 5 Data Sheet COUT = 47F, L1 = 47H 5.5 5.0 VISO (V) 4 VISO (V) 3 4.5 6.0 COUT = 47F, L1 = 100H 5.5 5.0 2 4.5 0 5 10 15 20 25 30 TIME (ms) Figure 27. Typical VISO Startup with 10 mA, 50 mA, and 400 mA Output Load, 5 V Input to 3.3 V Output 1.0 90% LOAD 0.5 0 -2 0 2 10% LOAD 4 6 8 10 12 14 TIME (ms) 09369-041 0 09369-038 VISO AT 10mA VISO AT 50mA VISO AT 400mA ILOAD (A) 1 Figure 30. Typical VISO Load Transient Response at 10% to 90% of 400 mA Load, fSW = 500 kHz, 5 V Input to 5 V Output 4.0 5 COUT = 47F, L1 = 47H 3.5 3.0 VISO (V) 4 VISO (V) 3 4.0 COUT = 47F, L1 = 100H 3.5 3.0 0 0 5 10 15 20 25 30 TIME (ms) 09369-039 VISO AT 10mA VISO AT 50mA VISO AT 250mA Figure 28. Typical VISO Startup with 10 mA, 50 mA, and 250 mA Output Load, 3.3 V Input to 3.3 V Output 1.0 90% LOAD 0.5 0 -2 0 2 10% LOAD 4 6 8 10 12 14 TIME (ms) 09369-042 1 ILOAD (A) 2 Figure 31. Typical VISO Load Transient Response at 10% to 90% of 400 mA Load, fSW = 500 kHz, 5 V Input to 3.3 V Output 18 4.0 16 3.5 COUT = 47F, L1 = 47H 3.0 VISO (V) 14 VISO (V) 12 4.0 10 COUT = 47F, L1 = 100H 3.5 8 3.0 6 0 5 10 15 TIME (ms) 20 25 30 Figure 29. Typical VISO Startup with 10 mA, 20 mA, and 100 mA Output Load, 5 V Input to 15 V Output 1.0 90% LOAD 0.5 0 -2 0 2 4 10% LOAD 6 TIME (ms) 8 10 12 14 09369-044 0 09369-040 VISO AT 10mA VISO AT 20mA VISO AT 100mA 2 ILOAD (A) 4 Figure 32. Typical VISO Load Transient Response at 10% to 90% of 250 mA Load, fSW = 500 kHz, 3.3 V Input to 3.3 V Output Rev. B | Page 22 of 36 Data Sheet 18 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 3.34 COUT = 47F, L1 = 47H, L2 = 47H 16 18 3.30 COUT = 47F, L1 = 100H, L2 = 100H 14 3.28 12 20 0 -2 90% LOAD 10% LOAD 100 2 10 6 X1 (V) 200 14 18 22 26 30 34 TIME (ms) X2 ON 10 0 -2 X1 ON -1 0 1 2 TIME (s) Figure 36. Typical VISO Output Voltage Ripple at 250 mA Load, fSW = 500 kHz, 3.3 V Input to 3.3 V Output Figure 33. Typical VISO Load Transient Response at 10% to 90% of 100 mA Load, fSW = 500 kHz, 5 V Input to 15 V Output 15.4 5.04 15.2 VISO (V) 5.02 VISO (V) 3.32 09369-047 16 ILOAD (A) VISO (V) 12 09369-043 VISO (V) 14 5.00 15.0 14.8 4.98 14.6 20 10 X1 ON 0 -2 -1 0 1 2 TIME (s) 3.34 VISO (V) 3.32 3.30 3.28 20 X1 ON -1 0 1 2 TIME (s) 09369-046 X1 (V) X2 ON 0 -2 10 0 -2 X1 ON -1 0 1 2 TIME (s) Figure 37. Typical VISO Output Voltage Ripple at 100 mA Load, fSW = 500 kHz, 5 V Input to 15 V Output Figure 34. Typical VISO Output Voltage Ripple at 400 mA Load, fSW = 500 kHz, 5 V Input to 5 V Output 10 X2 ON Figure 35. Typical VISO Output Voltage Ripple at 400 mA Load, fSW = 500 kHz, 5 V Input to 3.3 V Output Rev. B | Page 23 of 36 09369-048 X1 (V) X2 ON 09369-045 X1 (V) 20 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Data Sheet TERMINOLOGY IDD1 (Q) IDD1 (Q) is the minimum operating current drawn at the VDD1 power input when there is no external load at VISO and the I/O pins are operating below 2 Mbps, requiring no additional dynamic supply current. IDD1 (D) IDD1 (D) is the typical input supply current with all channels simultaneously driven at a maximum data rate of 25 Mbps with the full capacitive load representing the maximum dynamic load conditions. Treat resistive loads on the outputs separately from the dynamic load. IDD1 (MAX) IDD1 (MAX) is the input current under full dynamic and VISO load conditions. tPHL Propagation Delay The tPHL propagation delay is measured from the 50% level of the falling edge of the VIx signal to the 50% level of the falling edge of the VOx signal. tPLH Propagation Delay The tPLH propagation delay is measured from the 50% level of the rising edge of the VIx signal to the 50% level of the rising edge of the VOx signal. Propagation Delay Skew (tPSK) tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH that is measured between units at the same operating temperature, supply voltages, and output load within the recommended operating conditions. Channel-to-Channel Matching Channel-to-channel matching is the absolute value of the difference in propagation delays between two channels when operated with identical loads. Minimum Pulse Width The minimum pulse width is the shortest pulse width at which the specified pulse width distortion is guaranteed. Maximum Data Rate The maximum data rate is the fastest data rate at which the specified pulse width distortion is guaranteed. Rev. B | Page 24 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 APPLICATIONS INFORMATION D1 L1 VISO = +3.3V TO +15V T1 The ADuM347x devices implement undervoltage lockout (UVLO) with hysteresis on the VDDA power input. This feature ensures that the converter does not go into oscillation due to noisy input power or slow power-on ramp rates. CIN 1 X1 20 VREG 2 GND1 19 GND2 3 NC 18 VDD2 4 X2 5 VIA/VOA 6 VIB/VOB 7 VIC/VOC VDD1 0.1F R2 15 VIB/VOB 14 VIC/VOC 13 VID/VOD 9 VDDA 12 OC 10 GND1 11 GND 2 ROC 100k D1 L1 T1 47H 47F COUT1 L2 COUT2 VDD1 CIN D2 VISO = +12V TO +24V UNREGULATED +6V TO +12V 47F 47H D3 R1 D4 1 X1 20 VREG 2 GND1 19 GND2 3 NC 4 X2 5 VIA/VOA 7 VIC/VOC VDD1 0.1F ADuM3470/ ADuM3471/ ADuM3472/ ADuM3473/ ADuM3474 0.1F +5V 18 VDD2 17 FB VFB 16 VIA/VOA R2 15 VIB/VOB 14 VIC/VOC 8 VID/VOD 13 VID/VOD 9 VDDA 12 OC 10 GND1 11 GND 2 ROC 100k VISO = VFB x (R1 + R2)/R2 FOR VISO = 15V OR LESS, VREG CAN CONNECT TO VISO. Figure 39. Doubling Power Supply D1 L1 T1 47H 47F COUT1 VISO = COARSELY REGULATED +5V TO +15V VDD1 CIN D2 L2 COUT2 47F UNREGULATED -5V TO -15V 47H D3 R1 D4 Figure 40, which also uses a voltage doubling secondary circuit, is an example of a coarsely regulated, positive power supply and an unregulated, negative power supply for outputs of approximately 5 V, 12 V, and 15 V. VISO = VFB x (R1 + R2)/R2 VFB 16 VIA/VOA 8 VID/VOD 6 VIB/VOB For all the circuits shown in Figure 38 to Figure 40, the isolated output voltage (VISO) can be set with the voltage dividers, R1 and R2 (values 1 k to 100 k) using the following equation: +5V 17 FB Figure 38. Single Power Supply APPLICATION SCHEMATICS Figure 39 shows a voltage doubling circuit that can be used for a single supply with an output that exceeds 15 V; 15 V is the largest supply that can be connected to the regulator input, VREG (Pin 20). In the circuit shown in Figure 39, the output voltage can be as high as 24 V, and the voltage at the VREG pin can be as high as 12 V. When using the circuit shown in Figure 39 to obtain an output voltage lower than 10 V (for example, VDD1 = 3.3 V, VISO = 5 V), connect VREG to VISO directly. ADuM3470/ ADuM3471/ ADuM3472/ ADuM3473/ ADuM3474 0.1F VISO = VFB x (R1 + R2)/R2 FOR VISO = 3.3V OR 5V, CONNECT V REG , VDD2 , AND V ISO. A minimum load current of 10 mA is recommended to ensure optimum load regulation. Smaller loads can generate excess noise on the output due to short or erratic PWM pulses. Excess noise generated in this way can cause regulation problems in some circumstances. The ADuM347x devices have three main application schematics, as shown in Figure 38 to Figure 40. Figure 38 has a center-tapped secondary and two Schottky diodes that provide full wave rectification for a single output, typically for power supplies of 3.3 V, 5 V, 12 V, and 15 V. For single supplies when VISO = 3.3 V or 5 V, VREG, VDD2, and VISO can be connected together. R1 D2 1 X1 20 VREG 2 GND1 3 NC 4 X2 5 VIA/VOA 6 VIB/VOB 7 VIC/VOC 8 VID/VOD VDD1 0.1F 19 GND2 ADuM3470/ ADuM3471/ ADuM3472/ ADuM3473/ ADuM3474 18 VDD2 17 FB 0.1F +5V VFB 16 VIA/VOA R2 15 VIB/VOB 14 VIC/VOC 13 VID/VOD 9 VDDA 12 OC 10 GND1 11 GND 2 ROC 100k VISO = VFB x (R1 + R2)/R2 where VFB is the internal feedback voltage (approximately 1.25 V). Rev. B | Page 25 of 36 Figure 40. Positive Supply and Unregulated Negative Supply 09369-017 The secondary (VISO) side controller regulates the output using a feedback voltage, VFB, from a resistor divider on the output to create a PWM control signal that is sent to the primary (VDD1) side by a dedicated iCoupler data channel labeled VFB. The primary side PWM converter varies the duty cycle of the X1 and X2 switches to modulate the oscillator circuit and control the power being sent to the secondary side. This feedback allows for significantly higher power and efficiency. VDD1 09369-015 The dc-to-dc converter section of the ADuM347x uses a secondary side controller architecture with isolated pulse-width modulation (PWM) feedback. VDD1 power is supplied to an oscillating circuit that switches current to the primary side of an external power transformer using internal push-pull switches at the X1 and X2 pins. Power transferred to the secondary side of the transformer is full wave rectified with external Schottky diodes (D1 and D2), filtered with the L1 inductor and COUT capacitor, and regulated to the isolated power supply voltage from 3.3 V to 15 V. 47H COUT 47F 09369-016 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 TRANSFORMER DESIGN Custom transformers were designed for use in the circuits shown in Figure 38, Figure 39, and Figure 40 (see Table 18). The transformers designed for use with the ADuM347x differ from other transformers used with isolated dc-to-dc converters that do not regulate the output voltage. The output voltage is regulated by a PWM controller in the ADuM347x that varies the duty cycle of the primary side switches in response to a secondary side feedback voltage, VFB, received through an isolated digital channel. The internal controller has a maximum duty cycle of 40%. TRANSFORMER TURNS RATIO To determine the transformer turns ratio--taking into account the losses for the primary switches and the losses for the secondary diodes and inductors--the external transformer turns ratio for the ADuM347x can be calculated using Equation 1. NS NP = VISO + VD (1) VDD1 ( MIN ) x D x 2 where: NS/NP is the primary to secondary turns ratio. VISO is the isolated output supply voltage. VD is the Schottky diode voltage drop (0.5 V maximum). VDD1 (MIN) is the minimum input supply voltage. D is the duty cycle = 0.30 for a 30% typical duty cycle (40% is the maximum duty cycle). 2 is a multiplier factor used for the push-pull switching cycle. NS NP The circuit shown in Figure 39 uses double windings and diode pairs to create a doubler circuit; therefore, half the output voltage, VISO/2, is used, as shown in Equation 2. = 2 + VD (2) VDD1 ( MIN ) x D x 2 For the circuit shown in Figure 39 using the 5 V to 15 V reference design in Table 18 and with VDD1 (MIN) = 4.5 V, the turns ratio is NS/NP = 3. The circuit shown in Figure 40 also uses double windings and diode pairs to create a doubler circuit. However, because a positive and negative output voltage are created, VISO is used, and the external transformer turns ratio can be calculated using Equation 3. NP For a 3.3 V input to 3.3 V output isolated single power supply and with VDD1 (MIN) = 3.0 V, the turns ratio is also NS/NP = 2. Therefore, the same transformer turns ratio, NS/NP = 2, can be used for the three single power applications: 5 V to 5 V, 5 V to 3.3 V, and 3.3 V to 3.3 V. VISO where: NS/NP is the primary to secondary turns ratio. VISO is the isolated output supply voltage. VISO/2 is used because the circuit uses two pairs of diodes, creating a doubler circuit. VD is the Schottky diode voltage drop (0.5 V maximum). VDD1 (MIN) is the minimum input supply voltage. D is the duty cycle = 0.30 for a 30% typical duty cycle (40% is the maximum duty cycle). 2 is a multiplier factor used for the push-pull switching cycle. NS For the circuit shown in Figure 38 using the 5 V to 5 V reference design in Table 18 and with VDD1 (MIN) = 4.5 V, the turns ratio is NS/NP = 2. Data Sheet = VISO + VD (3) VDD1 ( MIN ) x D x 2 where: NS/NP is the primary to secondary turns ratio. VISO is the isolated output supply voltage. VD is the Schottky diode voltage drop (0.5 V maximum). VDD1 (MIN) is the minimum input supply voltage. D is the duty cycle = 0.35 for a 35% typical duty cycle (40% is the maximum duty cycle). 2 is a multiplier factor used for the push-pull switching cycle. For the circuit shown in Figure 40, the duty cycle, D, is set to 0.35 for a 35% typical duty cycle to reduce the maximum voltages seen by the diodes for a 15 V supply. For the circuit shown in Figure 40 using the +5 V to 15 V reference design in Table 18 and with VDD1 (MIN) = 4.5 V, the turns ratio is NS/NP = 5. Table 18. Transformer Reference Designs Part No. JA4631-BL JA4650-BL KA4976-AL TGSAD-260V6LF TGSAD-290V6LF TGSAD-292V6LF TGAD-260NARL TGAD-290NARL TGAD-292NARL Manufacturer Coilcraft Coilcraft Coilcraft Halo Electronics Halo Electronics Halo Electronics Halo Electronics Halo Electronics Halo Electronics Turns Ratio, PRI:SEC 1CT:2CT 1CT:3CT 1CT:5CT 1CT:2CT 1CT:3CT 1CT:5CT 1CT:2CT 1CT:3CT 1CT:5CT ET Constant (V x s Min) 18 18 18 14 14 14 14 14 14 Total Primary Inductance (H) 255 255 255 389 389 389 389 389 389 Rev. B | Page 26 of 36 Total Primary Resistance () 0.2 0.2 0.2 0.8 0.8 0.8 0.8 0.8 0.8 Isolation Voltage (rms) 2500 2500 2500 2500 2500 2500 1500 1500 1500 Isolation Type Basic Basic Basic Supplemental Supplemental Supplemental Functional Functional Functional Reference Figure 38 Figure 39 Figure 40 Figure 38 Figure 39 Figure 40 Figure 38 Figure 39 Figure 40 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 TRANSFORMER ET CONSTANT The next transformer design factor to consider is the ET constant. This constant determines the minimum V x s constant of the transformer over the operating temperature. ET values of 14 V x s and 18 V x s were selected for the ADuM347x transformer designs listed in Table 18 using the following equation: ET ( MIN ) = VDD1 ( MAX ) The ADuM347x devices also have an open-loop mode where the output voltage is not regulated and is dependent on the transformer turns ratio, NS/NP, and the conditions of the output including output load current and the losses in the dc-to-dc converter circuit. This open-loop mode is selected when the OC pin is connected high to the VDD2 pin. In open-loop mode, the switching frequency is 318 kHz. TRANSIENT RESPONSE f SW ( MIN ) x 2 where: VDD1 (MAX) is the maximum input supply voltage. fSW (MIN) is the minimum primary switching frequency = 300 kHz in startup. 2 is a multiplier factor used for the push-pull switching cycle. TRANSFORMER PRIMARY INDUCTANCE AND RESISTANCE Another important characteristic of the transformer for designs with the ADuM347x is the primary inductance. Transformers for the ADuM347x are recommended to have between 60 H to 100 H of inductance per primary winding. Values of primary inductance in this range are needed for smooth operation of the ADuM347x pulse-by-pulse current-limit circuit, which can help protect against a build-up of saturation currents in the transformer. If the inductance is specified for the total of both primary windings, for example, as 400 H, the inductance of one winding is one-fourth of two equal windings, or 100 H. Another important characteristic of the transformer for designs with the ADuM347x is primary resistance. Primary resistance as low as is practical (less than 1 ) helps to reduce losses and improves efficiency. The dc primary resistance can be measured and specified, and is shown for the transformers in Table 18. TRANSFORMER ISOLATION VOLTAGE Isolation voltage and isolation type should be determined for the requirements of the application and then specified. The transformers in Table 18 have been specified for 2500 V rms for supplemental or basic isolation and for 1500 V rms functional isolation. Other isolation levels and isolation voltages can be specified and requested from the transformer manufacturers listed in Table 18 or from other manufacturers. SWITCHING FREQUENCY The ADuM347x switching frequency can be adjusted from 200 kHz to 1 MHz by changing the value of the ROC resistor shown in Figure 38, Figure 39, and Figure 40. The value of the ROC resistor needed for the desired switching frequency can be determined from the switching frequency vs. ROC resistance curve shown in Figure 9. The output filter inductor value and output capacitor value for the ADuM347x application schematics have been designed to be stable over the switching frequency range of 500 kHz to 1 MHz, when loaded from 10% to 90% of the maximum load. The load transient response of the ADuM347x output voltage for 10% to 90% of the full load is shown in Figure 30 to Figure 33 for the application schematics in Figure 38 and Figure 39. The response shown is slow but stable and can have more output change than desired for some applications. The output voltage change with load transient is reduced, and the output is shown to remain stable by adding more inductance to the output circuits, as shown in the second VISO output waveform in Figure 30 to Figure 33. For additional improvement in transient response, add a 0.1 F ceramic capacitor (CFB) in parallel with the high feedback resistor. This value helps to reduce the overshoot and undershoot during load transients. COMPONENT SELECTION The ADuM347x digital isolators with 2 W dc-to-dc converters require no external interface circuitry for the logic interfaces. Power supply bypassing is required at the input and output supply pins. Note that a low ESR ceramic bypass capacitor of 0.1 F is required on Side 1 between Pin 9 and Pin 10, and on Side 2 between Pin 18 and Pin 19, as close to the chip pads as possible. The power supply section of the ADuM347x uses a high oscillator frequency to efficiently pass power through the external power transformer. In addition, normal operation of the data section of the iCoupler introduces switching transients on the power supply pins. Bypass capacitors are required for several operating frequencies. Noise suppression requires a low inductance, high frequency capacitor; ripple suppression and proper regulation require a large value capacitor. To suppress noise and reduce ripple, large value ceramic capacitors of X5R or X7R dielectric type are recommended. The recommended capacitor value is 10 F for VDD1 and 47 F for VISO. These capacitors have a low ESR and are available in moderate 1206 or 1210 sizes for voltages up to 10 V. For output voltages larger than 10 V, two 22 F ceramic capacitors can be used in parallel. See Table 19 for recommended components. Table 19. Recommended Components Part No. GRM32ER71A476KE15L GRM32ER71C226KEA8L GRM31CR71A106KA01L MBR0540T1G Manufacturer Murata Murata Murata ON Semiconductor LQH3NPN470MM0 ME3220-104KL LQH6PPN470M43 LQH6PPN101M43 Murata Coilcraft Murata Murata Rev. B | Page 27 of 36 Value 47 F, 10 V, X7R, 1210 22 F, 16 V, X7R, 1210 10 F, 10 V, X7R, 1206 Schottky, 0.5 A, 40 V, SOD-123 47 H, 0.41 A, 1212 100 H, 0.34 A, 1210 47 H, 1.10 A, 2424 100 H, 0.80 A, 2424 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Inductors must be selected based on the value and supply current needed. Most applications with switching frequencies between 500 kHz and 1 MHz and load transients between 10% and 90% of full load are stable with the 47 H inductor value listed in Table 19. Values as large as 200 H can be used for power supply applications with a switching frequency as low as 200 kHz to help stabilize the output voltage or for improved load transient response (see Figure 30 to Figure 33). Inductors in a small 1212 or 1210 size are listed in Table 19 with a 47 H value and a 0.41 A current rating to handle the majority of applications below a 400 mA load, and with a 100 H value and a 0.34 A current rating to handle a load up to 300 mA. Recommended Schottky diodes have low forward voltage to reduce losses and high reverse voltage of up to 40 V to withstand the peak voltages available in the doubling circuits shown in Figure 39 and Figure 40. PRINTED CIRCUIT BOARD (PCB) LAYOUT Figure 41 shows the recommended PCB layout for the ADuM347x. Note that the total lead length between the ends of the low ESR capacitor and the VDDx and GNDx pins must not exceed 2 mm. Installing a bypass capacitor with traces more than 2 mm in length can result in data corruption. VREG GND2 NC FB VIA/VOA VIB/VOB VIB/VOB VIC/VOC VIC/VOC VID/VOD VID/VOD VDDA OC GND1 GND2 The ADuM347x parts consist of two internal die attached to a split lead frame with two die attach paddles. For the purposes of thermal analysis, the die are treated as a thermal unit, with the highest junction temperature reflected in the JA value from Table 5. The value of JA is based on measurements taken with the parts mounted on a JEDEC standard, 4-layer board with fine width traces and still air. Under normal operating conditions, the ADuM347x devices operate at full load across the full temperature range without derating the output current. However, following the recommendations in the Printed Circuit Board (PCB) Layout section decreases thermal resistance to the PCB, allowing increased thermal margins at high ambient temperatures. PROPAGATION DELAY-RELATED PARAMETERS 09369-025 VIA/VOA THERMAL ANALYSIS The ADuM347x devices have a thermal shutdown circuit that shuts down the dc-to-dc converter and the outputs of the ADuM347x when a die temperature of approximately 160C is reached. When the die cools below approximately 140C, the ADuM347x dc-to-dc converter and outputs turn on again. VDD2 X2 The board layout in Figure 41 shows enlarged pads for Pin 2 and Pin 10 (GND1) on Side 1 and Pin 11 and Pin 19 (GND2) on Side 2. Large diameter vias should be implemented from the pad to the ground planes and power planes to increase thermal conductivity and to reduce inductance. Multiple vias in the thermal pads can significantly reduce temperatures inside the chip. The dimensions of the expanded pads are left to the discretion of the designer and depend on the available board space. Figure 41. Recommended PCB Layout In applications that involve high common-mode transients, ensure that board coupling across the isolation barrier is minimized. Furthermore, design the board layout such that any coupling that does occur affects all pins equally on a given component side. Failure to ensure this can cause voltage differentials between pins that exceed the absolute maximum ratings specified in Table 10, thereby leading to latch-up and/or permanent damage. The ADuM3470/ADuM3471/ADuM3472/ADuM3473/ ADuM3474 are power devices that dissipate approximately 1 W of power when fully loaded and running at maximum speed. Because it is not possible to apply a heat sink to an isolation device, the devices primarily depend on heat dissipation into the PCB through the GNDx pins. If the devices are used at high ambient temperatures, provide a thermal path from the GNDx pins to the PCB ground plane. Propagation delay is a parameter that describes the length of time it takes for a logic signal to propagate through a component (see Figure 42). The propagation delay to a logic low output can differ from the propagation delay to a logic high output. INPUT (VIx) 50% tPLH OUTPUT (VOx) tPHL 50% 09369-018 X1 GND1 Data Sheet Figure 42. Propagation Delay Parameters Pulse width distortion is the maximum difference between these two propagation delay values and is an indication of how accurately the timing of the input signal is preserved. Channel-to-channel matching refers to the maximum amount that the propagation delay differs between channels within a single ADuM347x component. Propagation delay skew refers to the maximum amount that the propagation delay differs between multiple ADuM347x components operating under the same conditions. Rev. B | Page 28 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Positive and negative logic transitions at the isolator input cause narrow (~1 ns) pulses to be sent to the decoder via the transformer. The decoder is bistable and is, therefore, either set or reset by the pulses, indicating input logic transitions. In the absence of logic transitions at the input for more than 1 s, periodic sets of refresh pulses indicative of the correct input state are sent to ensure dc correctness at the output. If the decoder receives no internal pulses for more than approximately 5 s, the input side is assumed to be unpowered or nonfunctional, and the isolator output is forced to a default state by the watchdog timer circuit (see Table 17). This situation should occur in the ADuM347x devices only during power-up and power-down operations. The limitation on the magnetic field immunity of the ADuM347x is set by the condition in which induced voltage in the transformer receiving coil is sufficiently large to either falsely set or reset the decoder. The following analysis defines the conditions under which this can occur. The 3.3 V operating condition of the ADuM347x is examined because it represents the most susceptible mode of operation. The pulses at the transformer output have an amplitude of >1.0 V. The decoder has a sensing threshold of approximately 0.5 V, thus establishing a 0.5 V margin in which induced voltages can be tolerated. The voltage induced across the receiving coil is given by V = (-d/dt) rn2; n = 1, 2, ..., N where: is the magnetic flux density (gauss). rn is the radius of the nth turn in the receiving coil (cm). N is the number of turns in the receiving coil. The preceding magnetic flux density values correspond to specific current magnitudes at given distances from the ADuM347x transformers. Figure 44 expresses these allowable current magnitudes as a function of frequency for selected distances. As shown in Figure 44, the ADuM347x is extremely immune and can be affected only by extremely large currents operated at high frequency very close to the component. For the 1 MHz example, a 0.5 kA current must be placed 5 mm away from the ADuM347x to affect the operation of the component. 1k DISTANCE = 5mm 0.1 10k 100k 1M 10M 100M Figure 44. Maximum Allowable Current for Various Current-to-ADuM347x Spacings At combinations of strong magnetic field and high frequency, any loops formed by PCB traces can induce error voltages sufficiently large to trigger the thresholds of succeeding circuitry. Care should be taken in the layout of such traces to avoid this possibility. 1 0.1 09369-019 0.01 100M DISTANCE = 100mm 1 MAGNETIC FIELD FREQUENCY (Hz) 10 10k 100k 10M 1M MAGNETIC FIELD FREQUENCY (Hz) 10 1k 100 0.001 1k DISTANCE = 1m 100 0.01 Given the geometry of the receiving coil in the ADuM347x and an imposed requirement that the induced voltage be, at most, 50% of the 0.5 V margin at the decoder, a maximum allowable magnetic field is calculated as shown in Figure 43. MAXIMUM ALLOWABLE MAGNETIC FLUX DENSITY (kgauss) For example, at a magnetic field frequency of 1 MHz, the maximum allowable magnetic field of 0.2 kgauss induces a voltage of 0.25 V at the receiving coil. This voltage is approximately 50% of the sensing threshold and does not cause a faulty output transition. Similarly, if such an event occurs during a transmitted pulse (and is of the worst-case polarity), it reduces the received pulse from >1.0 V to 0.75 V--still well above the 0.5 V sensing threshold of the decoder. 09369-020 DC CORRECTNESS AND MAGNETIC FIELD IMMUNITY MAXIMUM ALLOWABLE CURRENT (kA) Data Sheet Figure 43. Maximum Allowable External Magnetic Flux Density Rev. B | Page 29 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 POWER CONSUMPTION The VDD1 power supply provides power to the iCoupler data channels, as well as to the power converter. For this reason, the quiescent currents drawn by the power converter and the primary and secondary I/O channels cannot be determined separately. All of these quiescent power demands are combined in the IDD1 (Q) current (see the simplified diagram in Figure 45). The total IDD1 supply current is equal to the sum of the quiescent operating current; the dynamic current, IDD1 (D), demanded by the I/O channels; and any external IISO load. IDD1 (Q) IDD1 (D) IISO FB PRIMARY CONVERTER SECONDARY CONTROLLER IDDP (D) IISO (D) Figure 45. Power Consumption Within the ADuM347x Dynamic I/O current is consumed only when operating a channel at speeds higher than the refresh rate of fr. The dynamic current of each channel is determined by its data rate. Figure 18 and Figure 22 show the current for a channel in the forward direction, meaning that the input is on the primary side of the part. Figure 19 and Figure 23 show the current for a channel in the reverse direction, meaning that the input is on the secondary side of the part. Figure 18, Figure 19, Figure 22, and Figure 23 assume a typical 15 pF output load. The following relationship allows the total IDD1 current to be IDD1 = (IISO x VISO)/(E x VDD1) + ICHn; n = 1 to 4 (1) where: IDD1 is the total supply input current. IISO is the current drawn by the secondary side external load. E is the power supply efficiency at the given output load from Figure 13 or Figure 17 at the VISO and VDD1 condition of interest. ICHn is the current drawn by a single channel, determined from Figure 18, Figure 19, Figure 22, or Figure 23, depending on channel direction. The maximum external load can be calculated by subtracting the dynamic output load from the maximum allowable load. IISO (LOAD) = IISO (MAX) - IISO (D)n; n = 1 to 4 The preceding analysis assumes a 15 pF capacitive load on each data output. If the capacitive load is larger than 15 pF, the additional current must be included in the analysis of IDD1 and IISO (LOAD). POWER CONSIDERATIONS Soft Start Mode and Current-Limit Protection When the ADuM347x device first receives power from VDD1, it is in soft start mode, and the output voltage, VISO, is increased gradually while it is below the start-up threshold. In soft start mode, the width of the PWM signal is increased gradually by the primary converter to limit the peak current during VISO power-up. When the output voltage is larger than the start-up threshold, the PWM signal can be transferred from the secondary controller to the primary converter, and the dc-to-dc converter switches from soft start mode to the normal PWM control mode. If a short circuit occurs, the push-pull converter shuts down for approximately 2 ms and then enters soft start mode. If, at the end of soft start, a short circuit still exists, the process is repeated, which is called hiccup mode. If the short circuit is cleared, the ADuM347x device enters normal operation. SECONDARY DATA I/O 4CH 09369-024 PRIMARY DATA I/O 4CH Data Sheet (2) where: IISO (LOAD) is the current available to supply an external secondary side load. IISO (MAX) is the maximum external secondary side load current available at VISO. IISO (D)n is the dynamic load current drawn from VISO by an output or input channel, as shown for a single supply in Figure 20 or Figure 21 or for a double supply in Figure 24 or Figure 25. The ADuM347x devices also have a pulse-by-pulse current limit, which is active in startup and normal operation. This current limit protects the primary switches, X1 and X2, from exceeding approximately 1.2 A peak and also protects the transformer windings. Data Channel Power Cycle The ADuM347x data input channels on the primary side and the data input channels on the secondary side are protected from premature operation by UVLO circuitry. Below the minimum operating voltage, the power converter holds its oscillator inactive, and all input channel drivers and refresh circuits are idle. Outputs are held in a low state to prevent transmission of undefined states during power-up and power-down operations. During application of power to VDD1, the primary side circuitry is held idle until the UVLO preset voltage is reached. At that time, the data channels are initialized to their default low output state until they receive data pulses from the secondary side. The primary side input channels sample the input and send a pulse to the inactive secondary output. The secondary side converter begins to accept power from the primary, and the VISO voltage starts to rise. When the secondary side UVLO is reached, the secondary side outputs are initialized to their default low state until data, either a transition or a dc refresh pulse, is received from the corresponding primary side input. It can take up to 1 s after the secondary side is initialized for the state of the output to correlate with the primary side input. Secondary side inputs sample their state and transmit it to the primary side. Outputs are valid one propagation delay after the secondary side becomes active. Rev. B | Page 30 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 INSULATION LIFETIME All insulation structures eventually break down when subjected to voltage stress over a sufficiently long period. The rate of insulation degradation is dependent on the characteristics of the voltage waveform applied across the insulation. Analog Devices conducts an extensive set of evaluations to determine the lifetime of the insulation structure within the ADuM347x devices. In the case of unipolar ac or dc voltage, the stress on the insulation is significantly lower. This allows operation at higher working voltages while still achieving a 50-year service life. The working voltages listed in Table 11 can be applied while maintaining the 50-year minimum lifetime, provided that the voltage conforms to either the unipolar ac or dc voltage cases. Treat any crossinsulation voltage waveform that does not conform to Figure 47 or Figure 48 as a bipolar ac waveform, and limit its peak voltage to the 50-year lifetime voltage value listed in Table 11. The voltage presented in Figure 48 is shown as sinusoidal for illustration purposes only. It is meant to represent any voltage waveform varying between 0 V and some limiting value. The limiting value can be positive or negative, but the voltage cannot cross 0 V. Accelerated life testing is performed using voltage levels higher than the rated continuous working voltage. Acceleration factors for several operating conditions are determined, allowing calculation of the time to failure at the working voltage of interest. The values shown in Table 11 summarize the peak voltages for 50 years of service life in several operating conditions. In many cases, the working voltage approved by agency testing is higher than the 50-year service life voltage. Operation at working voltages higher than the service life voltage listed in Table 11 leads to premature insulation failure. The insulation lifetime of the ADuM347x depends on the voltage waveform type imposed across the isolation barrier. The iCoupler insulation structure degrades at different rates, depending on whether the waveform is bipolar ac, dc, or unipolar ac. Figure 46, Figure 47, and Figure 48 illustrate these different isolation voltage waveforms. Rev. B | Page 31 of 36 RATED PEAK VOLTAGE 09369-021 When power is removed from VDD1, the primary side converter and coupler shut down when the UVLO level is reached. The secondary side stops receiving power and starts to discharge. The outputs on the secondary side hold the last state that they received from the primary side until either the UVLO level is reached and the outputs are placed in their default low state, or the outputs detect a lack of activity from the inputs and the outputs are set to their default value before the secondary power reaches UVLO. Bipolar ac voltage is the most stringent environment. A 50-year operating lifetime under the bipolar ac condition determines the maximum working voltage recommended by Analog Devices. 0V Figure 46. Bipolar AC Waveform RATED PEAK VOLTAGE 09369-023 Because the rate of charge of the secondary side is dependent on the soft start cycle, loading conditions, input voltage, and output voltage level selected, care should be taken in the design to allow the converter to stabilize before valid data is required. 0V Figure 47. DC Waveform RATED PEAK VOLTAGE 0V Figure 48. Unipolar AC Waveform 09369-022 Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 Data Sheet OUTLINE DIMENSIONS 7.50 7.20 6.90 11 20 5.60 5.30 5.00 1 8.20 7.80 7.40 10 0.65 BSC 0.38 0.22 SEATING PLANE 8 4 0 COMPLIANT TO JEDEC STANDARDS MO-150-AE Figure 49. 20-Lead Shrink Small Outline Package [SSOP] (RS-20) Dimensions shown in millimeters Rev. B | Page 32 of 36 0.95 0.75 0.55 060106-A 0.05 MIN COPLANARITY 0.10 0.25 0.09 1.85 1.75 1.65 2.00 MAX Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 ORDERING GUIDE Model 1, 2, 3 ADuM3470ARSZ ADuM3470CRSZ ADuM3470WARSZ ADuM3470WCRSZ ADuM3471ARSZ ADuM3471CRSZ ADuM3471WARSZ ADuM3471WCRSZ ADuM3472ARSZ ADuM3472CRSZ ADuM3472WARSZ ADuM3472WCRSZ ADuM3473ARSZ ADuM3473CRSZ ADuM3473WARSZ ADuM3473WCRSZ ADuM3474ARSZ ADuM3474CRSZ ADuM3474WARSZ ADuM3474WCRSZ Number of Inputs, VDD1 Side 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 Number of Inputs, VISO Side 0 0 0 0 1 1 1 1 2 2 2 2 3 3 3 3 4 4 4 4 Maximum Data Rate (Mbps) 1 25 1 25 1 25 1 25 1 25 1 25 1 25 1 25 1 25 1 25 Maximum Propagation Delay, 5 V (ns) 100 60 100 60 100 60 100 60 100 60 100 60 100 60 100 60 100 60 100 60 Maximum Pulse Width Distortion (ns) 40 8 40 8 40 8 40 8 40 8 40 8 40 8 40 8 40 8 40 8 Temperature Range (C) -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 -40 to +105 Package Description 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP 20-Lead SSOP Package Option RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 RS-20 Z = RoHS Compliant Part. W = Qualified for Automotive Applications. 3 Tape and reel are available. The addition of an RL7 suffix designates a 7" (500 units) tape and reel option. 1 2 AUTOMOTIVE PRODUCTS The ADuM3470W, ADuM3471W, ADuM3472W, ADuM3473W, and ADuM3474W models are available with controlled manufacturing to support the quality and reliability requirements of automotive applications. Note that these automotive models may have specifications that differ from the commercial models; therefore, designers should review the Specifications section of this data sheet carefully. Only the automotive grade products shown are available for use in automotive applications. Contact your local Analog Devices account representative for specific product ordering information and to obtain the specific Automotive Reliability reports for these models. Rev. B | Page 33 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 NOTES Rev. B | Page 34 of 36 Data Sheet Data Sheet ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 NOTES Rev. B | Page 35 of 36 ADuM3470/ADuM3471/ADuM3472/ADuM3473/ADuM3474 NOTES (c)2010-2014 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D09369-0-5/14(B) Rev. B | Page 36 of 36 Data Sheet Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: ADUM3471ARSZ ADUM3472CRSZ-RL7 ADUM3473CRSZ ADUM3470ARSZ-RL7 ADUM3471ARSZ-RL7 ADUM3473CRSZ-RL7 ADUM3474CRSZ ADUM3474CRSZ-RL7 ADUM3472ARSZ-RL7 ADUM3471CRSZ ADUM3470CRSZ-RL7 ADUM3473ARSZ-RL7 ADUM3474ARSZ-RL7 ADUM3471CRSZ-RL7 ADUM3472CRSZ ADUM3473ARSZ ADUM3470CRSZ ADUM3474ARSZ ADUM3472ARSZ ADUM3470ARSZ ADUM3474WARSZ ADUM3473WCRSZ ADUM3473WARSZ ADUM3470WARSZ-RL7 ADUM3473WARSZ-RL7 ADUM3471WCRSZ-RL7 ADUM3474WCRSZ-RL7 ADUM3471WARSZ-RL7 ADUM3472WCRSZ ADUM3472WCRSZ-RL7 ADUM3470WCRSZRL7 ADUM3471WCRSZ ADUM3474WCRSZ ADUM3472WARSZ-RL7 ADUM3473WCRSZ-RL7 ADUM3470WARSZ ADUM3471WARSZ ADUM3472WARSZ ADUM3474WARSZ-RL7 ADUM3470WCRSZ