DG441/883, DG442/883 Monolithic Quad SPST CMOS Analog Switches June 1994 Features Description * This Circuit is Processed in Accordance to MIL-STD883 and is Fully Conformant Under the Provisions of Paragraph 1.2.1. The DG441/883 and DG442/883 monolithic CMOS analog switches are drop-in replacements for the popular DG201A/ 883 and DG202/883 series devices. They include four independent single pole single throw (SPST) analog switches, TTL and CMOS compatible digital inputs, and a voltage reference for logic thresholds. * ON-Resistance 85 Max * Low Power Consumption (PD <1.6mW) * Fast Switching Action - tON <250ns - tOFF <120ns (DG441/883) These switches feature lower analog ON resistance (<85) and faster switch time (tON <250ns) compared to the DG201A/883 and DG202/883. Charge injection has been reduced, simplifying sample and hold applications. * Low Charge Injection The improvements in the DG441/883 series are made possible by using a high voltage silicon-gate process. An epitaxial layer prevents the latch-up associated with older CMOS technologies. The 44V maximum voltage range permits controlling 40V peak-to-peak signals. Power supplies may be single-ended from +5V to +34V, or split from 5V to 20V. * Upgrade from DG201A/883/DG202/883 * TTL, CMOS Compatible * Single or Split Supply Operation Applications The four switches are bilateral, equally matched for AC or bidirectional signals. The ON resistance variation with analog signals is quite low over a 5V analog input range. The switches in the DG441/883 and DG442/883 are identical, differing only in the polarity of the selection logic. * Audio Switching * Battery Operated Systems * Data Acquisition * Hi-Rel Systems Ordering Information * Sample and Hold Circuits * Communication Systems PART NUMBER * Automatic Test Equipment Pinout TEMPERATURE RANGE o o PACKAGE DG441AK/883 -55 C to +125 C 16 Lead CerDIP DG442AK/883 -55oC to +125oC 16 Lead CerDIP Functional Diagrams DG441/883 DG441/883, DG442/883 (CERDIP) TOP VIEW DG442/883 S1 IN1 IN1 1 16 IN2 D1 2 15 D2 S1 3 14 S2 V- 4 13 V+ GND 5 12 NC S4 6 11 S3 D4 7 10 D3 IN4 8 9 IN3 S1 IN1 D1 S2 IN2 D1 S2 IN2 D2 S3 IN3 D2 S3 IN3 D3 S4 IN4 D3 S4 IN4 D4 D4 SWITCHES SHOWN FOR LOGIC "1" INPUT CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. http://www.intersil.com or 407-727-9207 | Copyright (c) Intersil Corporation 1999 59 512044 File Number 3687 Spec Number DG441/883, DG442/883 Pin Description TRUTH TABLE LOGIC VIN DG441 DG442 Logic Control for Switch 1 0 0.8V ON OFF D1 Drain (Output) Terminal for Switch 1 1 2.4V OFF ON 3 S1 Source (Input) Terminal for switch 1 4 V- Negative Power Supply Terminal 5 GND 6 S4 Source (Input) Terminal for Switch 4 7 D4 Drain (Output) Terminal for Switch 4 8 IN4 Logic Control for Switch 4 9 IN3 Logic Control for Switch 3 10 D3 Drain (Output) Terminal for Switch 3 11 S3 Source (Input) Terminal for Switch 3 12 NC No Internal Connection 13 V+ Positive Power Supply Terminal (Substrate) 14 S2 Source (Input) Terminal for Switch 2 15 D2 Drain (Output) Terminal for Switch 2 16 IN2 Logic Control for Switch 2 PIN SYMBOL 1 IN1 2 DESCRIPTION Ground Terminal (Logic Common) Spec Number 60 512044 Specifications DG441/883, DG442/883 Absolute Maximum Ratings Thermal Information V+ to V-. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44V GND to V- . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25V Digital Inputs, (Note 1) . . . . . . . . . . . (V-) -2V to (V+) + 2V or 30mA, Whichever Occurs First Continuous Current, S or D (Note 1). . . . . . . . . . . . . . . . . . . . . .30mA Peak Current, S or D (Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . .100mA Storage Temperature Range (A Suffix) . . . . . . . . . -65oC to +150oC Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300oC Thermal Resistance (Max, Note 3) JA JC CerDIP Package . . . . . . . . . . . . . . . . . . . 85oC/W 25oC/W Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +175oC Operating Temperature (A Suffix) . . . . . . . . . . . . . . -55oC to +125oC CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Operating Conditions Operating Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V Max Operating Temperature Range . . . . . . . . . . . . . . . . -55oC to +125oC Input Low Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.8V Max Input High Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2.4V Min Input Rise and Fall Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20ns TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: -55oC TA +125oC, V+ = +15V, V- = -15V, Unless Otherwise Specified PARAMETERS Drain-to-Source ON Resistance SYMBOL RDS(ON) CONDITIONS VIN = 0.8V DG441/883 DG442/883 VIN = 2.4V DG441/883 VIN = 0.8V DG442/883 Source OFF Leakage Current VIN = 2.4V IS(OFF) VIN = 2.4V DG441/883 DG442/883 VIN = 0.8V V+ = +13.5V, V- = -13.5V, IS = -10mA, VD = 8.5V GROUP A SUBGROUP TEMPERATURE 1, 3 2 +25oC, -55oC +125oC LIMITS UNITS - 85 - 100 - 85 2 +125oC - 100 V+ = +10.8V, V- = 0V, IS = -10mA, VD = 3.0V 1, 3 +25oC, -55oC - 160 2 +125oC - 200 V+ = +10.8V, V- = 0V, IS = -10mA, VD = 8.0V 1, 3 +25oC, -55oC - 160 2 +125oC - 200 V+ = +10.8V, V- = 0V, IS = -10mA, VD = 3.0V 1, 3 +25oC, -55oC - 160 2 +125oC - 200 V+ = +10.8V, V- = 0V, IS = -10mA, VD = 8.0V 1, 3 +25oC, -55oC - 160 2 +125oC - 200 V+ = +16.5V, V- = -16.5V, VS = 15.5V, VD = 15.5V 1 +25oC -0.5 0.5 nA -20 20 nA V+ = +13.5V, V- = -13.5V, IS = -10mA, VD = 8.5V 1, 3 V+ = +16.5V, V- = -16.5V, VS = 15.5V, VD = 15.5V 2, 3 +25oC, -55oC +125oC, -55oC 1 +25oC -0.5 0.5 nA 2, 3 +125oC, -55oC -20 20 nA Spec Number 61 512044 Specifications DG441/883, DG442/883 TABLE 1. DC ELECTRICAL PERFORMANCE CHARACTERISTICS (Continued) Device Tested at: -55oC TA +125oC, V+ = +15V, V- = -15V, Unless Otherwise Specified PARAMETERS Drain OFF Leakage Current SYMBOL ID(OFF) CONDITIONS VIN = 2.4V DG441/883 DG442/883 Channel ON Leakage Current DG441/883 VIN = 0.8V ID(ON) + IS(ON) DG442/883 VIN = 0.8V VIN = 2.4V V+ = +16.5V, V- = -16.5V, VS = 15.5V, VD = 15.5V V+ = +16.5V, V- = -16.5V, VS = 15.5V, VD = 15.5V V+ = +16.5V, V- = -16.5V, VS = VD = 15.5V V+ = +16.5V, V- = -16.5V, VS = VD = 15.5V GROUP A SUBGROUP TEMPERATURE 1 2, 3 +25oC +125oC, -55oC LIMITS UNITS -0.5 0.5 nA -20 20 nA 1 +25oC -0.5 0.5 nA 2, 3 +125oC, -55oC -20 20 nA 1 +25oC -0.5 0.5 nA 2, 3 +125oC, -55oC -40 40 nA 1 +25oC -0.5 0.5 nA 2, 3 +125oC, -55oC -40 40 nA Input Current with VIN Low IIL VIN Under Test = 0.8V, All Others = 2.4V 1, 2, 3 +25oC, +125oC, 55oC -0.5 0.5 A Input Current with VIN High IIH VIN Under Test = 2.4V, All Others = 0.8V 1, 2, 3 +25oC, +125oC, 55oC -0.5 0.5 A Positive Supply Current I+ V+ = 16.5V, V- = -16.5V, VIN = 0V 1, 2, 3 +25oC, +125oC, 55oC - 0.1 mA - 0.1 mA - 0.1 mA - 0.1 mA -1.0 - A V+ = 16.5V, V- = -16.5V, VIN = 5V V+ = 13.2V, V- = 0V, VIN = 0V V+ = 13.2V, V- = 0V, VIN = 5V Negative Supply Current I- V+ = 16.5V, V- = -16.5V, VIN = 0V V+ = 16.5V, V- = -16.5V, VIN = 5V V+ = 13.2V, V- = 0V, VIN = 0V IGND -55oC 2 +125oC -100 - A 1, 3 +25oC, -55oC -1.0 - A 2 +125oC -100 - A -1.0 - A 1, 3 +25oC, -55oC 2 +125oC -100 - A 1, 3 +25oC, -55oC -1.0 - A 2 +125oC -100 - A -100 - A -100 - A V+ = 13.2V, V- = 0V, VIN = 0V -100 - A V+ = 13.2V, V- = 0V, VIN = 5V -100 - A V+ = 13.2V, V- = 0V, VIN = 5V Ground Current 1, 3 +25oC, V+ = 16.5V, V- = -16.5V, VIN = 0V V+ = 16.5V, V- = -16.5V, VIN = 5V 1, 2, 3 +25oC, +125oC, 55oC - Spec Number 62 512044 Specifications DG441/883, DG442/883 TABLE 2. AC ELECTRICAL PERFORMANCE CHARACTERISTICS Device Tested at: -55oC TA +125oC, V+ = +15V, V- = -15V, Unless Otherwise Specified PARAMETERS SYMBOL Turn ON Time LIMITS GROUP A SUBGROUP TEMPERATURE CONDITIONS MIN MAX UNITS - 250 ns - 315 ns - 300 ns - 400 ns - 400 ns - 450 ns - 600 ns - 675 ns - 120 ns - 210 ns - 150 ns - 250 ns - 200 ns tON CL = 35pF, VS = 10V, RL = 1k DG441 DG442 CL = 35pF, VS = 10V, RL = 1k DG441 DG442 DG441 DG441 V+ = 12V, V- = 0V, CL = 35pF, VS = 8.0V, RL = 1k DG442 Turn OFF Time +125oC, 10, 11 V+ = 12V, V- = 0V, CL = 35pF, VS = 8.0V, RL = 1k DG442 +25oC 9 -55oC +25oC 9 +125oC, 10, 11 -55oC tOFF CL = 35pF, VS = 10V, RL = 1k DG441 DG442 CL = 35pF, VS = 10V, RL = 1k DG441 DG442 DG441, DG442 +25oC 9 +125oC, 10, 11 V+ = 12V, V- = 0V, CL = 35pF, VS = 8.0V, RL = 1k +25oC, 9, 10, 11 -55oC +125oC, -55oC NOTES: 1. All leads soldered to PC Board. 2. Room: +25oC. Cold: A suffix -55oC, D suffix -40oC. Hot: A suffix +125oC, D suffix +85oC. 3. Dissipation rating assumes device is mounted with all leads soldered to printed circuit board. 4. Typical values are for DESIGN AID ONLY, not guaranteed nor production tested. TABLE 3. ELECTRICAL PERFORMANCE CHARACTERISTICS Table 3 Intentionally Left Blank. TABLE 4. ELECTRICAL TEST REQUIREMENTS MIL-STD-883 TEST REQUIREMENTS SUBGROUPS (SEE TABLES 1 AND 2) Interim Electrical Parameters (Pre Burn-In) 1 Final Electrical Test Parameters 1 (Note 1), 2, 3, 9, 10, 11 Group A Test Requirements 1, 2, 3, 9, 10, 11 Groups C and D Endpoints 1 NOTE: 1. PDA applies to Subgroup 1 only. Spec Number 63 512044 DG441/883, DG442/883 Die Characteristics DIE DIMENSIONS: 2760m x 1780m x 485 25m METALLIZATION: Type: SiAl Thickness: 12kA 1kA GLASSIVATION: Type: Nitride Thickness: 8kA 1kA WORST CASE CURRENT DENSITY: 1.5 x 105A/cm2 Metallization Mask Layout DG441/883, DG442/883 D1 IN1 IN2 (2) (1) (16) (15) D2 S1 (3) (14) S2 V- (4) (13) V+ SUBSTRATE (12) NC GND (5) (11) S3 S4 (6) (7) D4 (8) IN4 (9) IN3 (10) D3 Spec Number 64 512044 DG441/883, DG442/883 Test Circuits VO is the steady state output with the switch on. Feedthrough via switch capacitance may result in spikes at the leading and trailing edge of the output waveform. tR < 20ns (10% to 90% VIN) tF < 20ns (90% to 10% VIN) V+ 3V LOGIC INPUT 50% SWITCH INPUT 0V tOFF VO VO IN1 SWITCH INPUT VS SWITCH OUTPUT D1 S1 0.8 VO 0.8 VO RL LOGIC INPUT 3V CL GND V- 0V Repeat test for Channels 2, 3 and 4. For load conditions, see Specifications CL (includes fixture and stray capacitance) RL V O = V S ----------------------------------R L + r DS ( ON ) tON NOTE: Logic input waveform is inverted for switches that have the opposite logic sense. FIGURE 1A. FIGURE 1B. FIGURE 1. SWITCHING TIME Burn-In Circuit DG441/883, DG442/883 A2 16 1 A1 2 OUT1 V- 6 IN4 V+ 13 VREF OPEN 12 IN3 11 7 OUT4 OUT3 10 4 VC1 D2 5 GND R1 OUT2 15 IN2 14 3 IN1 A3 8 A4 9 V+ R2 D1 C2 R3 R4 Spec Number 65 512044 DG441/883, DG442/883 Schematic Diagram (One Channel) V+ S VV+ INX D GND 1 PER DIE COMMON TO EVERY CHANNEL V- All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification. Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see web site http://www.intersil.com Spec Number 66 512044 DG441/883, DG442/883 Ceramic Dual-In-Line Frit Seal Packages (CerDIP) c1 F16.3 MIL-STD-1835 GDIP1-T16 (D-2, CONFIGURATION A) LEAD FINISH 16 LEAD CERAMIC DUAL-IN-LINE FRIT SEAL PACKAGE -D- -A- BASE METAL E b1 M M (b) -Bbbb S C A-B S SECTION A-A D S D BASE PLANE Q -C- SEATING PLANE A L S1 eA A A b2 b ccc M C A-B S e D S eA/2 INCHES (c) c aaa M C A - B S D S SYMBOL MIN MAX MIN MAX NOTES A - 0.200 - 5.08 - b 0.014 0.026 0.36 0.66 2 b1 0.014 0.023 0.36 0.58 3 b2 0.045 0.065 1.14 1.65 - b3 0.023 0.045 0.58 1.14 4 c 0.008 0.018 0.20 0.46 2 c1 0.008 0.015 0.20 0.38 3 D - 0.840 - 21.34 5 E 0.220 0.310 5.59 7.87 5 e 0.100 BSC 2.54 BSC - eA 0.300 BSC 7.62 BSC - 3.81 BSC - eA/2 NOTES: 1. Index area: A notch or a pin one identification mark shall be located adjacent to pin one and shall be located within the shaded area shown. The manufacturer's identification shall not be used as a pin one identification mark. 2. The maximum limits of lead dimensions b and c or M shall be measured at the centroid of the finished lead surfaces, when solder dip or tin plate lead finish is applied. MILLIMETERS 0.150 BSC L 0.125 0.200 3.18 5.08 - Q 0.015 0.060 0.38 1.52 6 S1 0.005 - 0.13 - 7 90o 105o 90o 105o - aaa - 0.015 - 0.38 - bbb - 0.030 - 0.76 - 3. Dimensions b1 and c1 apply to lead base metal only. Dimension M applies to lead plating and finish thickness. ccc - 0.010 - 0.25 - M - 0.0015 - 0.038 2, 3 4. Corner leads (1, N, N/2, and N/2+1) may be configured with a partial lead paddle. For this configuration dimension b3 replaces dimension b2. N 16 16 8 Rev. 0 4/94 5. This dimension allows for off-center lid, meniscus, and glass overrun. 6. Dimension Q shall be measured from the seating plane to the base plane. 7. Measure dimension S1 at all four corners. 8. N is the maximum number of terminal positions. 9. Dimensioning and tolerancing per ANSI Y14.5M - 1982. 10. Controlling dimension: INCH. Spec Number 67 512044 DG441, DG442 DESIGN INFORMATION Monolithic Quad SPST CMOS Analog Switches June 1994 The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves RDS(ON) vs VD AND POWER SUPPLY VOLTAGE RDS(ON) vs VD AND TEMPERATURE 100 80 5V V+ = +15V V- = -15V 70 80 60 8V 10V 60 rDS(ON) () rDS(ON) () +125oC 50 12V 40 15V 20V +85oC 40 +25oC 30 0oC +40oC -55oC 20 20 10 0 -20 0 VD (V) 0 -15 20 RDS(ON) vs VD AND TEMPERATURE (SINGLE 12V SUPPLY) 0 VD (V) 15 RDS(ON) vs VD AND UNIPOLAR POWER SUPPLY VOLTAGE 140 300 V- = 0V 120 +125oC 100 +85oC 80 +25oC 250 V+ = +5V 200 rDS(ON) () rDS(ON) () V+ = +12V V- = 0V 60 +40oC -55oC +10V +12V +15V +20V 50 20 0 +8V 100 0oC 40 150 0 0 6 VD (V) 12 0 INPUT CURRENT vs TEMPERATURE 105 10 VD (V) 20 SUPPLY CURRENT vs TEMPERATURE 105 V- = 0V 104 104 I+, IGND 103 +I, I-, IGND (mA) IIN (pA) 103 102 10 102 10 1 -(I-) 0.1 1 0.1 -55 0.01 0 50 TEMPERATURE (oC) 100 0.001 -55 125 0 50 TEMPERATURE (oC) 100 Spec Number 68 125 512044 DG441, DG442 DESIGN INFORMATION (Continued) The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves (Continued) CROSSTALK AND OFF ISOLATION vs FREQUENCY CHARGE INJECTION vs SOURCE VOLTAGE 140 50 120 40 CROSSTALK V+ = +15V V- = -15V SINGLE SUPPLY V+ = +12V V- = 0V 30 100 Q (pC) (-dB) 20 80 OFF ISOLATION 60 10 0 CL = 10nF CL = 1nF 40 -10 V+ = +15V V- = -15V REF 10dBm 20 0 102 103 -20 104 105 FREQUENCY (Hz) 106 -30 -10 107 SWITCHING TIMES vs INPUT VOLTAGE -5 0 VS (V) 5 10 SOURCE/DRAIN LEAKAGE CURRENTS 20 160 V+ = +15V V- = -15V IS(OFF), ID(OFF) tON (DG441) 140 0 120 -20 tON (DG442) 100 IS, ID (pA) t (ns) CL = 10nF CL = 1nF tOFF (DG442) 80 -40 IS(ON) + ID(ON) -60 60 tOFF (DG441) 40 20 2 -100 -15 5 3 4 INPUT VOLTAGE (V) V+ = +15V V- = -15V FOR I(OFF), VD = -VS -80 SWITCHING THRESHOLD vs SUPPLY VOLTAGE -10 -5 0 VS, VD (V) 5 10 15 SOURCE/DRAIN CAPACITANCE vs ANALOG VOLTAGE 2.4 25 V+ = +15V V- = -15V 20 1.6 VIN (V) CS, D (pF) CS(ON) + CD(ON) 15 10 0.8 5 0 CS(OFF), CD(OFF) 0 0 5 10 15 POSITIVE/NEGATIVE SUPPLIES (V) 20 -15 -10 -5 0 VA (V) 5 10 Spec Number 69 15 512044 DG441, DG442 DESIGN INFORMATION (Continued) The information contained in this section has been developed through characterization by Intersil Corporation and is for use as application and design information only. No guarantee is implied. Typical Performance Curves (Continued) SOURCE/DRAIN CAPACITANCE vs ANALOG VOLTAGE (SINGLE 12V SUPPLY) SOURCE/DRAIN LEAKAGE CURRENTS (SINGLE 12V SUPPLY) 20 10 V+ = +12V V- = 0V IS(OFF), ID(OFF) CS(ON) + CD(ON) 0 IS, ID (pA) CS, D (pF) 15 10 -10 -20 IS(ON) + ID(ON) CS(OFF), CD(OFF) 5 V+ = +12V V- = 0V FOR ID, VS = 0 FOR IS, VD = 0 -30 0 0 6 VA (V) -40 12 0 6 VS, VD (V) SWITCHING TIME vs POWER SUPPLY VOLTAGE (DG441) 12 SWITCHING TIMES vs INPUT VOLTAGE 160 400 V+ = +12V V- = 0V 140 tON (DG441) tON 300 120 t (ns) 80 200 tOFF 60 100 tOFF (DG442) 40 20 10 12 14 16 18 SUPPLY VOLTAGE (V) 20 tOFF (DG441) 0 22 2 3 4 INPUT VOLTAGE (V) 5 SWITCHING TIME vs POWER SUPPLY VOLTAGE (DG441) 500 V- = 0V 400 tON 300 t (ns) t (ns) tON (DG442) 100 200 100 tOFF 0 8 10 12 14 16 18 20 22 + SUPPLY VOLTAGE (V) Spec Number 70 512044