SIMATIC NET CP 5621 Betriebsanleitung (kompakt) Dieses Dokument enthalt Informationen in Deutsch. This document contains information in English. 02 A5E01156749 Einleitung 1 Beschreibung 2 Installation und Deinstallation des Treibers 3 Montage und Anschlieen 4 Inbetriebnahme 5 Umstieg von CP 5611 / CP 5611 A2 auf CP 5621 6 Zulassungen, Zertifikate 7 Technische Daten 8 Sicherheitshinweise Dieses Handbuch enthalt Hinweise, die Sie zu Ihrer personlichen Sicherheit sowie zur Vermeidung von Sachschaden beachten mussen. Die Hinweise zu Ihrer personlichen Sicherheit sind durch ein Warndreieck hervorgehoben, Hinweise zu alleinigen Sachschaden stehen ohne Warndreieck. Je nach Gefahrdungsstufe werden die Warnhinweise in abnehmender Reihenfolge wie folgt dargestellt. GEFAHR bedeutet, dass Tod oder schwere Korperverletzung eintreten wird, wenn die entsprechenden Vorsichtsmanahmen nicht getroffen werden. WARNUNG bedeutet, dass Tod oder schwere Korperverletzung eintreten kann, wenn die entsprechenden Vorsichtsmanahmen nicht getroffen werden. VORSICHT mit Warndreieck bedeutet, dass eine leichte Korperverletzung eintreten kann, wenn die entsprechenden Vorsichtsmanahmen nicht getroffen werden. VORSICHT ohne Warndreieck bedeutet, dass Sachschaden eintreten kann, wenn die entsprechenden Vorsichtsmanahmen nicht getroffen werden. ACHTUNG bedeutet, dass ein unerwunschtes Ergebnis oder Zustand eintreten kann, wenn der entsprechende Hinweis nicht beachtet wird. Beim Auftreten mehrerer Gefahrdungsstufen wird immer der Warnhinweis zur jeweils hochsten Stufe verwendet. Wenn in einem Warnhinweis mit dem Warndreieck vor Personenschaden gewarnt wird, dann kann im selben Warnhinweis zusatzlich eine Warnung vor Sachschaden angefugt sein. Qualifiziertes Personal Das zugehorige Gerat/System darf nur in Verbindung mit dieser Dokumentation eingerichtet und betrieben werden. Inbetriebsetzung und Betrieb eines Gerates/Systems durfen nur von qualifiziertem Personal vorgenommen werden. Qualifiziertes Personal im Sinne der sicherheitstechnischen Hinweise dieser Dokumentation sind Personen, die die Berechtigung haben, Gerate, Systeme und Stromkreise gema den Standards der Sicherheitstechnik in Betrieb zu nehmen, zu erden und zu kennzeichnen. Bestimmungsgemaer Gebrauch Beachten Sie Folgendes: WARNUNG Das Gerat darf nur fur die im Katalog und in der technischen Beschreibung vorgesehenen Einsatzfalle und nur in Verbindung mit von Siemens empfohlenen bzw. zugelassenen Fremdgeraten und -komponenten verwendet werden. Der einwandfreie und sichere Betrieb des Produktes setzt sachgemaen Transport, sachgemae Lagerung, Aufstellung und Montage sowie sorgfaltige Bedienung und Instandhaltung voraus. Marken Alle mit dem Schutzrechtsvermerk (R) gekennzeichneten Bezeichnungen sind eingetragene Marken der Siemens AG. Die ubrigen Bezeichnungen in dieser Schrift konnen Marken sein, deren Benutzung durch Dritte fur deren Zwecke die Rechte der Inhaber verletzen kann. Haftungsausschluss Wir haben den Inhalt der Druckschrift auf Ubereinstimmung mit der beschriebenen Hard- und Software gepruft. Dennoch konnen Abweichungen nicht ausgeschlossen werden, so dass wir fur die vollstandige Ubereinstimmung keine Gewahr ubernehmen. Die Angaben in dieser Druckschrift werden regelmaig uberpruft, notwendige Korrekturen sind in den nachfolgenden Auflagen enthalten. Siemens AG Automation and Drives Postfach 48 48 90327 NURNBERG DEUTSCHLAND Dokumentbestellnummer: A5E01156749 03/2008 Copyright (c) Siemens AG 2008. Anderungen vorbehalten Inhaltsverzeichnis 1 2 3 Einleitung .................................................................................................................................................. 4 1.1 Einleitung........................................................................................................................................ 4 1.2 Technical Support .......................................................................................................................... 5 Beschreibung ............................................................................................................................................ 6 2.1 Auspacken und Prufen................................................................................................................... 6 2.2 Lieferumfang................................................................................................................................... 6 2.3 Produktbeschreibung ..................................................................................................................... 6 Installation und Deinstallation des Treibers ............................................................................................... 8 3.1 Installation des Treibers ................................................................................................................. 8 3.2 Deinstallation des Treibers............................................................................................................. 8 4 Montage und Anschlieen......................................................................................................................... 9 5 Inbetriebnahme ....................................................................................................................................... 10 6 Umstieg von CP 5611 / CP 5611 A2 auf CP 5621................................................................................... 11 7 Zulassungen, Zertifikate .......................................................................................................................... 12 8 Technische Daten ................................................................................................................................... 14 CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 3 Einleitung 1 Einleitung 1.1 Einleitung Dokumentinhalt Die vorliegende Betriebsanleitung (Kompakt) umfasst Informationen mit denen Sie in der Lage sind, den Kommunikationsprozessor CP 5621 zu montieren und in Betrieb zu nehmen. Weitere Informationen zum CP 5621 Tabelle 1-1 Gliederung der Dokumentation fur den CP 5621 Dokumentbezeichnung Warum lesen? Betriebsanleitung kompakt CP 5621 Sie werden schrittweise gefuhrt, um den CP 5621 im PC zu installieren. Projektierungshandbuch PC-Stationen in Betrieb nehmen Sie erhalten die notwendigen Informationen zur Inbetriebnahme und Projektierung einer PROFIBUS Kommunikationsbaugruppe. Handbucher * SIMATIC NET Industrielle Kommunikation mit PG/PC Band 1 - Grundlagen * SIMATIC NET Industrielle Kommunikation mit PG/PC Band 2 - Schnittstellen Das Handbuch fuhrt in die Industrielle Kommunikation ein und erlautert die hierzu verfugbaren Kommunikationsprotokolle. Zusatzlich wird die OPCSchnittstelle als Anwenderprogrammierschnittstelle beschrieben. Installationsanleitung SIMATIC NET, PC Software" (Deutsch und Englisch) Mit diesem Dokument erhalten Sie die Informationen, um die SIMATIC NET, PC-Software-Produkte auf Ihrem PG/PC zu installieren. Weiterfuhrende Dokumentation Weiterfuhrende Dokumentation finden Sie auf der aktuellen Manual Collection DVD Bestellnummer 6GK1975-1AA00-3AA0 4 CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 Einleitung 1.2 Technical Support SIMATIC Technical Support Sie erreichen den Technical Support fur alle A&D-Produkte: Uber das Internet mit dem Support Request: http://www.siemens.de/automation/support-request Telefon: + 49 (0) 180 5050 222 Fax: + 49 (0) 180 5050 223 Weitere Informationen zu unserem Technical Support finden Sie im Internet unter: http://www.siemens.com/automation/service Service & Support im Internet Zusatzlich zu unserem Dokumentations-Angebot bieten wir Ihnen im Internet unser komplettes Wissen online an, unter: http://www.siemens.com/automation/service&support Dort finden Sie: Aktuelle Produkt-Informationen, FAQs, Downloads, Tipps und Tricks. Der Newsletter versorgt Sie standig mit den aktuellsten Informationen zu Ihren Produkten. Der Knowledge Manager findet die richtigen Dokumente fur Sie. Im Forum tauschen Anwender und Spezialisten weltweit Ihre Erfahrungen aus. Finden Sie Ihren Ansprechpartner fur Automation & Drives vor Ort uber unsere Ansprechpartner-Datenbank. Informationen uber Vor-Ort Service, Reparaturen, Ersatzteile und vieles mehr steht fur Sie unter dem Begriff "Leistungen" bereit. Trainingscenter Um Ihnen den Einstieg in die Industrielle Kommunikation zu erleichtern, bieten wir Ihnen entsprechende Kurse an. Wenden Sie sich bitte an Ihr regionales Trainingscenter oder an das zentrale Trainingscenter in D-90327 Nurnberg. Telefon: +49 (911) 895-3200 Web-Adresse: http://www.sitrain.com CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 5 Beschreibung 2 Beschreibung 2.1 Auspacken und Prufen Auspacken, Prufen 1. Uberprufen Sie das Paket auf Vollstandigkeit. 2. Uberprufen Sie die Einzelteile auf Transportschaden. WARNUNG Nehmen Sie nur unbeschadigte Teile in Betrieb! 2.2 Lieferumfang Folgende Teile gehoren zum Lieferumfang des CP 5621: Kommunikationsprozessor CP 5621 Vorliegende Betriebsanleitung (kompakt) fur CP 5621 2.3 Produktbeschreibung Kommunikationsprozessor CP 5621 Der Kommunikationsprozessor CP 5621 hat folgende Produktmerkmale: Die CP 5621-Baugruppe ist mit einer PROFIBUS-Schnittstelle bis 12 Mbit/s ausgestattet. Sie ist fur den Betrieb in PGs und PCs mit PCI-Express-Busschnittstelle vorgesehen. Mit dem Kommunikationsprozessor CP 5621 konnen bis zu 32 Gerate (PC, PG, SIMATIC S7 oder ET 200) zu einem Netzsegment gekoppelt werden. Durch Kopplung mehrerer Segmente mit Repeatern sind maximal 127 Teilnehmer anschliebar. Die zusatzlichen Schnittstellensignale fur die PLC Direktkopplung (PLC - Programmable Logic Control) werden bis 187,5 kbit/s unterstutzt. 6 CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 Beschreibung MPI/DP-Netz Die physikalische Kopplung der MPI/DP-Schnittstelle an das MPI/DP-Netz erfolgt uber ein potentialgetrenntes RS485-Interface, das Bestandteil der Baugruppe ist. Im MPI/DP-Netz sind je nach Netzkonfiguration Datenubertragungsraten von 9,6 kbit/s bis maximal 12 Mbit/s moglich. Hinweis Informationen zum Aufbau eines MPI-Netzes finden Sie im Handbuch "Aufbauen einer S7300", Best. Nr. 6ES7030 0AA01-8AA0. Statusleuchtdiode Auf der Frontplatte des CP 5621 befindet sich die Statusleuchtdiode. Die folgende Tabelle beschreibt die Betriebszustande: Anzeige Beschreibung aus Ruhezustand, Baugruppe wird momentan nicht verwendet. ein Eine Applikation benutzt die Baugruppe. blinkend Baugruppe wurde beispielsweise vom "Komponenten Konfigurator" mit der Funktion "Klingeln Ein" angesprochen. CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 7 Installation und Deinstallation des Treibers Installation und Deinstallation des Treibers 3.1 3 Installation des Treibers Voraussetzung Folgende Voraussetzungen mussen erfullt sein: Der Plug-and-Play-Manager ist im BIOS aktiviert. Installation des CP 5621-Treibers Der Treiber wird automatisch installiert, wenn Sie die CD "SIMATIC NET, PC Software" oder das Programm STEP 7 installieren. Der CP 5621 wurde ab der CD "SIMATIC NET, PC Software, Edition 2006" getestet und freigegeben. Die fur den CP 5621 freigegebene STEP 7-Version entnehmen Sie der Liesmich-Datei von STEP 7. 3.2 Deinstallation des Treibers Deinstallation des CP 5621-Treibers Der Treiber wird automatisch deinstalliert, wenn Sie die CD "SIMATIC NET, PC Software" oder STEP 7 deinstallieren. Hinweis Beachten Sie zur Deinstallation von STEP 7 folgende Hinweise in Deutsch bzw. Englisch: http://support.automation.siemens.com/ww/view/de/189025 http://support.automation.siemens.com/ww/view/en/189025 8 CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 Montage und Anschlieen Montage und Anschlieen 4 Hinweis Anzahl moglicher CP 5621 in einem Rechner Es sind maximal zwei CP 5621 in einem PG/PC zulassig. Vorgehensweise Gehen Sie beim Einbau und Anschluss des CP 5621 wie folgt vor: ACHTUNG Greifen Sie beim Hantieren mit der Baugruppe nicht auf die Anschlusse bzw. auf die elektronischen Bauelemente. Bitte beachten Sie die Manahmen gegen elektrostatische Aufladung (EGB Elektrostatisch gefahrdete Bauelemente) 1. Schalten Sie Ihren Rechner aus und ziehen Sie den Netzstecker aus der Steckdose. 2. Offnen Sie das Rechnergehause wie im Handbuch Ihres PG/PC beschrieben. 3. Stecken Sie den CP 5621 in einen PCI Express Steckplatz. Achten Sie darauf, dass der CP 5621 fest und gleichmaig in der Aufnahmebuchse des Steckplatzes steckt. 4. Schlieen Sie das Rechnergehause, wie im Handbuch Ihres PG/PC beschrieben. 5. Stecken Sie den Netzstecker wieder in die Steckdose, und schalten Sie Ihren Rechner ein. 6. Der Plug-and-Play-Mechanismus von Windows sucht nach dem Einbau des Kommunikationsprozessors CP 5621 nach einem Treiber. CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 9 Inbetriebnahme 5 Inbetriebnahme Vor der Inbetriebnahme Beachten Sie vor der Inbetriebnahme folgenden Hinweis: VORSICHT Vor der Inbetriebnahme sind die Hinweise in der entsprechenden aktuellen Dokumentation zu beachten. Die Bestelldaten hierfur entnehmen Sie bitte den Katalogen, oder wenden Sie sich an Ihre ortliche Siemens-Geschaftsstelle. Projektierung Der CP 5621 wird in STEP 7 oder NCM PC als CP 5611 projektiert. Verhalten Der CP 5621 gibt sich aus Kompatibilitatsgrunden im PC als CP 5611 aus. Dies ist kein Fehler, sondern beabsichtigt. 10 CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 Umstieg von CP 5611 / CP 5611 A2 auf CP 5621 Umstieg von CP 5611 / CP 5611 A2 auf CP 5621 6 Der CP 5621 kann als Ersatz fur den CP 5611 bzw. CP 5611 A2 eingesetzt werden. Dazu sind weder Software-Updates noch Anderung der Projektierung notwendig. Gehen Sie wie folgt beschrieben vor: 1. Schalten Sie den PC aus. 2. Bauen Sie den CP 5611/CP 5611 A2 aus. 3. Bauen Sie den CP 5621 in einem PCI-Express Steckplatz ein. 4. Starten Sie den PC erneut. 5. Konfigurieren Sie den CP 5621 wie den vorherigen CP 5611/CP 5611 A2. Hinweis Wenn der Hardware-Assistent von Windows erscheint, dann bestatigen Sie die vorgeschlagenen Schritte (auer die Suche nach neuen Treibern im Internet). Hinweis Die fur den CP 5611 bzw. CP 5611 A2 verwendete Projektierung muss neu geladen werden. CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 11 Zulassungen, Zertifikate 7 Zulassungen, Zertifikate Produktbezeichnung SIMATIC NET CP 5621, 6GK1562-1AA00 EMV-Richtlinie Link im Internet Die EG-Konformitatserklarung zu diesem Produkt finden Sie mit Hilfe des Produktnamens im Internet unter folgender Adresse: http://supportauthoring.automation.siemens.com Abschnitt Selbsthilfe; geben Sie dort "EG Konformitatserklarung" und den Produktnamen ein; Beispiel deutsch: "EG Konformitatserklarung CP 5621", Beispiel englisch: "Declaration of Conformity CP 5621". Reaktion: Das Zertifikat erscheint im Suchergebnis. Das oben aufgefuhrte SIMATIC NET-Produkt erfullt die Anforderungen der EG-Richtlinie: 89/336/EWG "Elektromagnetische Vertraglichkeit" Einsatzbereich Die Produkte sind ausgelegt fur den Einsatz in folgenden Bereichen: Einsatzbereich Anforderungen an Storaussendung Storfestigkeit Wohnbereich, Geschafts- und Gewerbebereich sowie Kleinbetriebe EN 61000-6-3 EN 61000-6-1 Industriebereich EN 61000-6-4 EN 61000-6-2 Aufbaurichtlinien beachten Die Produkte erfullen die Anforderungen, wenn Sie bei Installation und Betrieb die Aufbaurichtlinien und Sicherheitshinweise einhalten, die in dieser Beschreibung sowie im "PROFIBUS Netzhandbuch" beschrieben ist. Arbeiten am Produkt Zum Schutz des Produktes vor Entladung von statischer Elektrizitat muss sich das Bedienpersonal vor dem Beruhren der Baugruppe elektrostatisch entladen. 12 CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 Zulassungen, Zertifikate Hinweis Das Produkt wurde in einem Gerat getestet, das ebenfalls die oben genannten Normen einhalt. Beim Betrieb der Baugruppe in einem Gerat, das diese Normen nicht erfullt, kann die Einhaltung der entsprechenden Werte nicht garantiert werden. Konformitatserklarung Die EG-Konformitatserklarung wird gema den oben genannten EG-Richtlinien fur die zustandigen Behorden zur Verfugung gehalten bei: Siemens Aktiengesellschaft Industry Sector Industrial Communication (A&D SC IC) Postfach 4848 D-90327 Nurnberg Maschinenrichtlinie Die Produkte sind keine Maschinen im Sinne der EG-Richtlinie Maschinen. Es gibt deshalb fur diese Produkte keine Konformitatserklarung bezuglich der EG-Richtlinie Maschinen 2006/42/EG. Sind die Produkte Teil der Ausrustung einer Maschine, mussen sie vom Maschinenhersteller in das Verfahren zur Konformitatserklarung einbezogen werden. Hinweis fur Australien (C-TICK) Das Produkt CP 5621 erfullt die Anforderungen der Norm AS/NZS 3548. ICES-Konformitat Das digitale Klasse B-Produkt CP 5621 erfullt die Anforderungen der kanadischen Norm ICES-003. CSA-Zulassung Das SIMATIC NET Produkt CP 5621 verfugt uber eine Zulassung nach Standard CAN/CSA C22.2 No. 60950-1. Hinweis fur USA (FCC) Informationen hierzu erhalten Sie im englischen Teil dieses Dokuments. UL-Zulassung Das SIMATIC NET Produkt CP 5621 verfugt uber eine Zulassung nach Standard UL 609501, First Edition. CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 13 Technische Daten 8 Technische Daten CP 5621 Folgende technische Daten gelten fur den Kommunikationsprozessor CP 5621: Konstruktiver Aufbau Baugruppenformat PCI-Express-Flachbaugruppe mit Standardhohe und halber Lange Mae (H x T) in mm 111 x 129 Gewicht ca. 100 g Baugruppen-Steckprinzip PCI-Express-Direktstecker Bus Interface PCI Express V1.0a, Plug and Play Spannung Betriebsspannung Sicherheitsspannung (SELV) nach EN 60950 Nennspannungen (Grenzwerte) DC 12 V und 3,3 V Stromaufnahme bei Nennspannung Bei DC 12 V max. 180 mA Bei DC 3,3 V max. 400 mA Datenubertragung Ubertragungsgeschwindigkeit 9,6 kbit/s bis 12 Mbit/s Schnittstellen Anschluss an PG/PC PCI Express x1; auch in x4-, x8- oder x16 Steckplatzen betreibbar. Steckverbinder 9-polige D-SUB-Buchsenleiste mit Schraubverriegelung Ubertragungsart RS 485 erdfrei innerhalb der SELV-Grenzen Betriebsart der MPI/DP-Schnittstelle Potentialfrei (Schnittstellensignale), erdgebunden (Leitungsschirm) 14 CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 Technische Daten Elektromagnetische Vertraglichkeit (EMV) Storaussendung Klasse B nach EN 55022 Storfestigkeit auf Signalleitungen +/- 2 kV FCC Klasse B nach IEC 61000-4-5, Surge +/- 1 kV nach IEC 61000-4-3, Burst Storfestigkeit gegen Entladen statischer Elektrizitat +/- 6 kV, Contact discharge nach IEC 61000-4-2 Storfestigkeit gegen Hochfrequenzeinstrahlung * * * 10 V/m bei 80 MHz - 2 GHz nach IEC 61000-4-3 10 V/m mit 80 % Amplitudenmodulation mit 1 kHz 10 kHz - 80 MHz nach IEC 61000-4-6 Sicherheit UL/CSA-Zulassung Der CP 5621 erfullt alle Anforderungen an Zusatzbaugruppen gema Zulassung cULus. Mechanische Umgebungsbedingungen Betriebsschwingung Gepruft nach IEC 60068 2 6: 10 ... 58 Hz, Amplitude: 0,075 mm, 58 ... 500 Hz; Beschleunigung: 10 m/s2, 10 Zyklen/Achse Betriebsschocken Gepruft nach IEC 60068 2 27; Halbsinus: 50 m/s2 (5 g), 30 ms, 100 Schocks/Achse Klimatische Bedingungen Temperatur (Betrieb) Gepruft nach IEC 60068 2 1, 60068-2-2: +5 ... +55 C, Temperaturanderung: max. 10 K/h Transport- und Lagertemperatur -20 ... +60 C, Temperaturanderung: max. 20 K/h Feuchte (Betrieb) Gepruft nach EN/IEC 60068-2-78: 5 ... 85 % bei 30 C (keine Betauung) Rascher Temperaturwechsel im Betrieb Gepruft nach IEC 60068-2-14: +5 ... +55 C, 5 Zyklen Rascher Temperaturwechsel bei Lagerung/Transport Gepruft nach IEC 60068-2-14: -20 ... +60 C, 2 Zyklen Temperaturwechsel bei Feuchte bei Lagerung/Transport Gepruft nach EN/IEC 60068-2-30: 25 ... 55 C bei 95 % (keine Betauung) CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 15 Technische Daten Belegung der PROFIBUS-Schnittstelle Die SUB D-Buchsenleiste ist wie folgt belegt: PIN-Nr. Kurzbezeichnung Bedeutung Eingang/Ausgang 1 NC Buchse Pin 1 ist nicht beschaltet. - 2 NC (M24) Buchse Pin 2 ist nicht beschaltet. Bei anderen MPI/DPKomponenten kann auf diesem Pin der Ruckleiter der potentialfreien 24 V Versorgung liegen. - 3 LTG_B Signalleitung B der CP 5621-Baugruppe Ein-/Ausgang 4 RTSAS RTSAS, Eingangssignal fur MPI/DP-Bus. Das Steuersignal ist "1"-aktiv, wenn die AS sendet. Eingang 5 M5EXT M5EXT Ruckleiter (GND) der 5-V-Versorgung. Die Strombelastung durch einen externen Verbraucher, der zwischen P5EXT und M5EXT angeschlossen wird, darf max. 90 mA betragen. Ausgang 6 P5EXT P5EXT Versorgung (+5 V) der 5V-Versorgung. Die Strombelastung durch einen externen Verbraucher, der zwischen P5EXT und M5EXT angeschlossen wird, darf max. 90 mA betragen (kurzschlussfest). - 7 NC (P24V) Buchse Pin 7 ist nicht beschaltet. Bei anderen MPI/DPKomponenten kann auf diesem Pin die Versorgung P24V der potentialfreien 24 V Versorgung liegen. 8 LTG_A Signalleitung A der CP 5621-Baugruppe Ein-/Ausgang 9 RTS RTS Ausgangssignal der CP 5621-Baugruppe. Das Steuersignal ist "1"-aktiv, wenn das Gerat (PG oder PC) sendet. Ausgang Schirm 16 auf Steckergehause CP 5621 Betriebsanleitung (kompakt), 02, A5E01156749 SIMATIC NET CP 5621 Operating Instructions (Compact) This document contains information in English. 02 A5E01156749 Introduction 1 Description 2 Installing and uninstalling the driver 3 Installing and connecting up 4 Commissioning 5 Converting from CP 5611/ CP 5611 A2 to CP 5621 6 Approval, Certificates 7 Technical specifications 8 Safety Guidelines This manual contains notices you have to observe in order to ensure your personal safety, as well as to prevent damage to property. The notices referring to your personal safety are highlighted in the manual by a safety alert symbol, notices referring only to property damage have no safety alert symbol. These notices shown below are graded according to the degree of danger. DANGER indicates that death or severe personal injury will result if proper precautions are not taken. WARNING indicates that death or severe personal injury may result if proper precautions are not taken. CAUTION with a safety alert symbol, indicates that minor personal injury can result if proper precautions are not taken. CAUTION without a safety alert symbol, indicates that property damage can result if proper precautions are not taken. NOTICE indicates that an unintended result or situation can occur if the corresponding information is not taken into account. If more than one degree of danger is present, the warning notice representing the highest degree of danger will be used. A notice warning of injury to persons with a safety alert symbol may also include a warning relating to property damage. Qualified Personnel The device/system may only be set up and used in conjunction with this documentation. Commissioning and operation of a device/system may only be performed by qualified personnel. Within the context of the safety notes in this documentation qualified persons are defined as persons who are authorized to commission, ground and label devices, systems and circuits in accordance with established safety practices and standards. Prescribed Usage Note the following: WARNING This device may only be used for the applications described in the catalog or the technical description and only in connection with devices or components from other manufacturers which have been approved or recommended by Siemens. Correct, reliable operation of the product requires proper transport, storage, positioning and assembly as well as careful operation and maintenance. Trademarks All names identified by (R) are registered trademarks of the Siemens AG. The remaining trademarks in this publication may be trademarks whose use by third parties for their own purposes could violate the rights of the owner. Disclaimer of Liability We have reviewed the contents of this publication to ensure consistency with the hardware and software described. Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. Siemens AG Automation and Drives Postfach 48 48 90327 NURNBERG GERMANY Ordernumber: A5E01156749 03/2008 Copyright (c) Siemens AG 2008. Technical data subject to change Table of contents 1 2 3 4 Introduction ............................................................................................................................................... 4 1.1 Introduction..................................................................................................................................... 4 1.2 Technical support ........................................................................................................................... 5 Description ................................................................................................................................................ 6 2.1 Unpacking and checking ................................................................................................................ 6 2.2 Components of the product............................................................................................................ 6 2.3 Description of the product .............................................................................................................. 6 Installing and uninstalling the driver........................................................................................................... 8 3.1 Installing the driver ......................................................................................................................... 8 3.2 Uninstalling the driver..................................................................................................................... 8 Installing and connecting up ...................................................................................................................... 9 5 Commissioning........................................................................................................................................ 10 6 Converting from CP 5611/ CP 5611 A2 to CP 5621 ................................................................................ 11 7 Approval, Certificates .............................................................................................................................. 12 7.1 8 FCC compliance information........................................................................................................ 14 Technical specifications .......................................................................................................................... 15 CP 5621 Operating Instructions (Compact), 02, A5E01156749 3 Introduction 1 Introduction 1.1 Introduction Content of the document These operating instructions (compact) contain the information you require to install and commission the CP 5621 communications processor. Further information on the CP 5621 Table 1-1 Structure of the documentation for the CP 5621 Name of the document Why you should read it Operating Instructions (compact) CP 5621 This provides a step-by-step guide to installing the CP 5621 in your PC. Configuration Manual Commissioning PC Stations This contains the information required to commission and configure a PROFIBUS communications module. Manuals * SIMATIC NET Industrial Communication with PG/PC Part 1 - Basics * SIMATIC NET Industrial Communication with PG/PC Part 2 - Interfaces This manual introduces you to industrial communication and explains the available communication protocols. It also describes the OPC interface as a user programming interface. Installation Instructions SIMATIC NET, PC Software (German and English) This document provides you with the information required to install the SIMATIC NET PC software products on your PG/PC. Further documentation You will find further information on the current Manual Collection DVD Order number 6GK1975-1AA00-3AA0 4 CP 5621 Operating Instructions (Compact), 02, A5E01156749 Introduction 1.2 Technical support SIMATIC Technical Support You can contact Technical Support for all A&D products as follows: Via the Internet with the Support Request: http://www.siemens.de/automation/support-request Telephone: + 49 (0) 180 5050 222 Fax: + 49 (0) 180 5050 223 You will find further information on our technical support on the Internet at: http://www.siemens.com/automation/service Service & Support on the Internet In addition to our range of documentation, we also provide all of our technical information on the Internet at: http://www.siemens.com/automation/service&support Here, you will find the following information: Current product information, FAQs, downloads, tips and tricks. The newsletter provides you with the latest information on your products. The Knowledge Manager will help you find just the documents you need. In the forum, users and experts worldwide exchange ideas and swap experience. Find your local contact for Automation & Drives in our contacts database. Information about local service, repair, and replacement parts and much more can be found under "Services". Training center To help you become familiar with industrial communication, we offer courses on a variety of topics. Please contact your regional Training Center, or the central Training Center in D90327 Nuremberg. Telephone: +49 (911) 895-3200 Internet: http://www.sitrain.com CP 5621 Operating Instructions (Compact), 02, A5E01156749 5 Description 2 Description 2.1 Unpacking and checking Unpacking, checking 1. Make sure that the package is complete. 2. Check all the parts for transport damage. WARNING Do not use any parts that show evidence of damage! 2.2 Components of the product The following components are supplied with the CP 5621: CP 5621 communications processor These Operating Instructions (compact) for CP 5621 2.3 Description of the product CP 5621 communications processor The CP 5621 communications processor has the following features: The CP 5621 module is equipped with a PROFIBUS interface up to 12 Mbps. It is intended for operation in PGs and PCs with a PCI Express bus interface. With the CP 5621 communications processor, you can connect up to 32 devices (PC, PG, SIMATIC S7 or ET 200) to a network segment. By linking several segments with repeaters, a maximum of 127 nodes can be connected. For the additional interface signals for the direct link to the PLC (programmable logic controller), up to 187.5 Kbps are supported. 6 CP 5621 Operating Instructions (Compact), 02, A5E01156749 Description MPI/DP network The physical link of the MPI/DP interface to the MPI/DP network is via a floating RS-485 interface that is part of the module. Depending on the network configuration, data transmission rates of 9.6 Kbps to a maximum of 12 Mbps are possible in the MPI/DP network. Note For information on setting up an MPI network, refer to the manual "S7-300 Installation", order no. 6ES7030-0AA01-8BA0. Status LED The status LED is located on the front panel of the CP 5621. The following table describes the operating states: Appearance Description off Idle, the module is not currently in use. on An application is using the module. flashing The module has been addressed, for example by the "Station Configuration Editor" using the "Ring on" function. CP 5621 Operating Instructions (Compact), 02, A5E01156749 7 Installing and uninstalling the driver 3 Installing and uninstalling the driver 3.1 Installing the driver Requirements The following requirements must be met: The plug-and-play manager is enabled in the BIOS. Installing the CP 5621 driver The driver is installed automatically when you install the "SIMATIC NET PC Software" CD or the STEP 7 program. The CP 5621 has been tested and released as of the "SIMATIC NET, PC Software, Edition 2006" CD. For the STEP 7 version released for the CP 5621, refer to the STEP 7 readme file. 3.2 Uninstalling the driver Uninstalling the CP 5621 driver The driver is uninstalled automatically when you uninstall the "SIMATIC NET PC Software" CD or the STEP 7 program. Note When you uninstall STEP 7, keep to the following instructions in German or English: http://support.automation.siemens.com/ww/view/de/189025 http://support.automation.siemens.com/ww/view/en/189025 8 CP 5621 Operating Instructions (Compact), 02, A5E01156749 Installing and connecting up Installing and connecting up 4 Note Maximum number of CP 5621 modules in one computer A maximum of two CP 5621 modules can be installed in one PG/PC. Procedure To install and connect up the CP 5621 follow the steps outlined below: NOTICE When handling the module, make sure that you do not touch the connectors or the electronic components. When installing the module make sure that you avoid electrostatic discharge (ESD) 1. Turn off your computer and pull out the power cable connector from the socket. 2. Open the computer housing as described in the manual accompanying your PG/PC. 3. Insert the CP 5621 in a PCI Express slot. Make sure that the CP 5621 sits firmly and uniformly in the slot. 4. Close the computer housing as described in the manual accompanying your PG/PC. 5. Plug the power supply connector into the socket again and turn on your computer. 6. After you have installed the CP 5621 communications processor, the Windows plug-andplay mechanism searches for a driver. CP 5621 Operating Instructions (Compact), 02, A5E01156749 9 Commissioning 5 Commissioning Prior to commissioning Before putting the product into operation, note the following warning: CAUTION Prior to startup read the relevant current documentation. For ordering data of the documentation please refer to the catalogs or contact your local Siemens office. Configuration The CP 5621 is configured in STEP 7 or NCM PC as a CP 5611. Reaction For reasons of compatibility, the CP 5621 is displayed as a CP 5611 on the PC. This is intentional and not an error. 10 CP 5621 Operating Instructions (Compact), 02, A5E01156749 Converting from CP 5611/ CP 5611 A2 to CP 5621 Converting from CP 5611/ CP 5611 A2 to CP 5621 6 The CP 5621 can be used as a replacement for the CP 5611 or CP 5611 A2. This requires neither software updates nor changes to the configuration. Follow the steps outlined below: 1. Turn off the PC. 2. Remove the CP 5611/CP 5611 A2. 3. Install the CP 5621 in a PCI Express slot. 4. Restart the PC. 5. Configure the CP 5621 just as the previous CP 5611/CP 5611 A2. Note When the Windows hardware wizard appears, confirm the proposed steps (except for searching for new hardware drivers on the Internet). Note The configuration used for the CP 5611 or CP 5611 A2 needs to be reloaded. CP 5621 Operating Instructions (Compact), 02, A5E01156749 11 Approval, Certificates 7 Approval, Certificates Product name SIMATIC NET CP 5621, 6GK1562-1AA00 EMC directive Internet link You will find the EC Declaration of Conformity for this product under the product name on the Internet at the following address: http://supportauthoring.automation.siemens.com Self-help section; enter "EC Declaration of Conformity" and the product name; for example in German: "EG Konformitatserklarung CP 5621", or for example in English: "Declaration of Conformity CP 5621". Reaction: The certificate appears in the search results. The above listed SIMATIC NET product meets the requirements of the EC directive: 89/336/EEC "Electromagnetic Compatibility" Area of application The products are designed for use in the following environments: Area of application Requirements Emission Immunity Domestic area, commercial and light industrial environments EN 61000-6-3 EN 61000-6-1 Industrial environment EN 61000-6-4 EN 61000-6-2 Adherence to the installation guidelines The products meet the requirements providing you adhere to the guidelines for installation and safety during installation and operation as described in this document and in the "PROFIBUS Network Manual". Working on the product To protect the product from electrostatic discharge, personnel must discharge any static electricity from their bodies before touching the module. 12 CP 5621 Operating Instructions (Compact), 02, A5E01156749 Approval, Certificates Note The product was tested in a device that also meets the standards listed above. When operating the module in a device that does not meet these standards, there can be no guarantee that the values will be achieved. Declaration of conformity The EC Declaration of Conformity is available for the responsible authorities according to the above-mentioned EC Directive at the following address: Siemens Aktiengesellschaft Industry Sector Industrial Communication (A&D SC IC) Postfach 4848 D-90327 Nurnberg, Germany Machinery directive The products are not machines in the sense of the EC Machinery Directive. There is therefore no declaration of conformity relating to the EC Machinery Directive 2006/42/EEC for these products. If the products are part of the equipment of a machine, they must be included in the declaration of conformity procedure by the manufacturer of the machine. Notice for Australia (C-TICK) The product CP 5621 meets the requirements of the AS/NZS 3548 standard. ICES conformity The digital class B product CP 5621 fulfills the requirements of Canadian standard ICES-003. CSA approval The SIMATIC NET product CP 5621 is approved in accordance with standard CAN/CSA C 22.2 no. 60950-1. Notice for USA (FCC) You will find this information in the English part of the document. UL approval The SIMATIC NET product CP 5621 is approved in accordance with standard UL 60950-1, First Edition. CP 5621 Operating Instructions (Compact), 02, A5E01156749 13 Approval, Certificates 7.1 FCC compliance information FCC compliance information Note The CP 5621 has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help Shielded cables Shielded cables must be used with equipment to maintain compliance with FCC regulations. 14 CP 5621 Operating Instructions (Compact), 02, A5E01156749 Technical specifications 8 Technical specifications CP 5621 The following technical specifications apply to the CP 5621 communications processor: Construction Module format PCI Express card - standard height and half length Dimensions (H x D) in mm 111 x 129 Weight Approx. 100 g Card connector principle PCI Express connector Bus interface PCI Express V1.0a, plug and play Voltage Operating voltage Safety extra low voltage (SELV) to EN 60950 Rated voltage (limit values) 12 V and 3.3 V DC Current consumption at rated voltage At 12 V DC max. 180 mA At 3,3 V DC max. 400 mA Data transmission Transmission speed 9.6 Kbps to 12 Mbps Interfaces Connection to PG/PC PCI Express x1; can also be operated in x4, x8 or x16 slots. Plug-in connector 9-pin D-sub socket strip with screw lock Transmission method RS-485 floating within SELV limits Mode of the MPI/DP interface Floating (interface signals), non-floating (cable shield) CP 5621 Operating Instructions (Compact), 02, A5E01156749 15 Technical specifications Electromagnetic compatibility (EMC) Emission Class B to EN 55022 Immunity on signal cables +/- 2 kV FCC class B to IEC 61000-4-5, surge +/- 1 kV to IEC 61000-4-3, burst Immunity to discharge of static electricity +/- 6 kV, contact discharge to IEC 61000-4-2 Immunity to radiated RF * * * 10 V/m at 80 MHz - 2 GHz to IEC 61000-4-3 10 V/m with 80 % amplitude modulation at 1 kHz 10 kHz - 80 MHz to IEC 61000-4-6 Safety UL/CSA approval The CP 5621 meets all requirements for add-on modules according to the cULus approval. Mechanical environmental conditions Vibration Tested to IEC 60068 2 6: 10 ... 58 Hz, Amplitude: 0.075 mm, 58 ... 500 Hz; Acceleration: 10 m/s2, 10 cycles/axis Shock Tested to IEC 60068 2 27; Half sine: 50 m/s2 (5 g), 30 ms, 100 shocks/axis Climatic conditions Temperature (operation) Tested to IEC 60068 2 1, 60068-2-2: +5 ... +55 C, Temperature change: max. 10 K/h Transport and storage temperature -20 ... +60 C, Temperature change: max. 20 K/h Humidity (operation) Tested to EN/IEC 60068-2-78: 5 ... 85% at 30 C (no condensation) Fast temperature change in operation Tested to IEC 60068-2-14: +5 ... +55 C, 5 cycles Fast temperature change during storage/transport Tested to IEC 60068-2-14: -20 ... +60 C, 2 cycles Damp heat, cyclic during storage/transport Tested to EN/IEC 60068-2-30: 25 ... 55 C at 95 % (no condensation) 16 CP 5621 Operating Instructions (Compact), 02, A5E01156749 Technical specifications Assignment of the PROFIBUS interface The pinning of the D-sub socket is as follows: Pin no. Abbreviation Meaning Input/output 1 NC Socket pin 1 is not connected. - 2 NC (M24) Socket pin 2 is not connected. With other MPI/DP components, the return line of the floating 24 V power supply may be connected to this pin. - 3 LTG_B Signal line B of the CP 5621 module Input/output 4 RTSAS RTSAS, input signal for MPI/DP bus. The control signal is Input "1" active when the AS is sending. 5 M5EXT M5EXT return line (GND) of the 5 V power supply. The current load caused by an external consumer connected between P5EXT and M5EXT must not exceed a maximum of 90 mA. Output 6 P5EXT P5EXT power supply (+5 V) of the 5 V supply. The current load caused by an external consumer connected between P5EXT and M5EXT must not exceed a maximum of 90 mA (short-circuit proof). - 7 NC (P24V) Socket pin 7 is not connected. With other MPI/DP components, the P24V supply of the floating 24 V power supply may be connected to this pin. - 8 LTG_A Signal line A of the CP 5621 module Input/output 9 RTS RTS output signal of the CP 5621 module. The control signal is "1" active when the device (PG or PC) is sending. Output Shield on connector casing CP 5621 Operating Instructions (Compact), 02, A5E01156749 17