DATENBLATT / Specification Sach Nr.: T60403-K5032-X102 Item no.: VACUU M SCHM ELZE K-No.: 25606 Powerline transformer Customer: Customers part no.: Date: 26.03.2015 Page 1 Vorschlag zur Anordnung der Anschlussflachen (Example for pad positions) DC= Date Code F = Factory 0,6 x 0,4 7 6 3 Connections: No. 1, 2, 3, 4, 6, 7 Mechanical outline (mm): (General Tolerances DIN ISO 2768-c) Toleranz der Stiftabstande 0,2mm (Tolerances grid distance) of Removed pins: No. 5, 8 0,15 DC 16,6 17,1 12,7 14 3,0 F Beschriftung: marking 4 2,54 1 Pin 1 10,16 9 13,2 10 DC 5032X102 F 1,5 10,16 Operational data/characteristic data (nominal values): Schematic diagram: IC side f = 10...1000 kHz mains side 7 1 N1 IRMS < 100 mA (50/60Hz) 2 3 N2 N3 RCu1 135 m ; RCu2 135 m, RCu3 230 m 6 4 Operating temperature: Storage temperature: u = 1 : 1 : 2 -40 C ... +120 C -40 C ... + 85 C Inspection: (V: 100%-Test; AQL...: DIN ISO 2859-Teil1) 1) (V) M3014: Ut,r.m.s. = 6,5 kV, Ut, r.m.s. = 0,5 kV, 2 s, 2 s, N3 vs N1+2 N1 vs N2 2) (AQL 0,25) M3011/1: L3 700 H, f = 10 kHz, 3) (V) M3011/6: Polarity, turns ratio: Tolerance 2 % UAC,r.m.s. = 100 mV see page 2 Applicable documents: Date 26.03.15 22.07.14 Hrsg.: editor Name Bs Pf. KB-E Index 82 82 see page 2 Change Typo: storage temperature changed from +120C ==> +85C. Lapiary change Characteristic data: IDC < 100 mA changed to IRMS < 100 mA (50/60Hz). Lapidary change Bearb: Bs KB-PM: Ert. designer check Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten freig.: HH released Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden. Any offenders are liable to pay all relevant damages. DATENBLATT / Specification Sach Nr.: T60403-K5032-X102 Item no.: VACUU M SCHM ELZE K-No.: 25606 Powerline transformer Customer: Customers part no.: Date: 26.03.2015 Page 2 of 3 Inspection: (V: 100%-Test; AQL...: DIN ISO 2859-Teil1) 4) (Fix05) M3291: Solderability test acc. to chapter 1 5) (AQL M3200: Mechanical test 1/S4) Type test 1) High voltage test according to M3014 Ut, r.m.s. = 7,5 kV, 2) M3292: 1 min, N1+N2 gegen/vs N3 Resistance to soldering heat acc. to chapter 2 Measurements after temperature balance of the test samples at room temperature Applicable documents: Constructed, manufactured and tested in accordance to EN 60950 (IEC 950) and agrees with the standards. Parameters: Reinforced insulation: N1+N2 to N3 and / or Reinforced insulation: N1+N2 to N3 Working voltage: 450 V r.m.s. Working voltage: 300 V r.m.s. Overvoltage category: 3 Overvoltage category: 4 Pollution degree: 2 Pollution degree: 2 Insulation material group: 3 Insulation material group: 3 Housing material, casting resin and wire UL - listed Packing: Drypack / MSL according VAC M3027 Hrsg.: editor KB-E Bearb: Bs KB-PM: Ert. designer check Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten freig.: HH released Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden. Any offenders are liable to pay all relevant damages. DATENBLATT / Specification Sach Nr.: T60403-K5032-X102 Item no.: VACUU M SCHM ELZE K-No.: 25606 Powerline transformer Customer: Customers part no.: Date: 26.03.2015 Page 3 of 3 packing information / Verpackungsinformation 0,5 P=20 B0=17,9 W=32 K0=10,7 A0=13,7 Die ersten zwei Nester gequetscht fur besseres einfadeln. (the first two nests must be crushed for better thread) Blistergurt leding 25 empty pockets Vorlauf 25 leere Nester Blistergurt laging 25 empty pockets Nachlauf 25 leere Nester Deckband 400mm langer wie Blistergurt (cover longer like carrier tape) Reel laging:>25 empty pockets Nachlauf >25 leere Nester leading:>25 empty pockets Vorlauf >25 leere Nester Orientierung of Pin 1 in carrier tape Anordnung von Stift 1 im Blistergurt Insertion of components according orientation 1 shown in M-sheet 3510 Einsetzen der Bauelemente nach M-Blatt 3510 Orientierung 1 quantities in packing: 200 pieces/tape (packing carton) 200 Bauelemente/Rolle Verpackungsmenge 5 tapes reel/carton (outside)=1000 pieces /carton(outside) 5Rollen/Karton =1000 Bauelemente /Auenkarton Hrsg.: editor KB-E Bearb: Bs KB-PM: Ert. designer check Weitergabe sowie Vervielfaltigung dieser Unterlage, Verwertung und Mitteilung ihres Inhalts nicht gestattet, soweit nicht ausdrucklich zugestanden. Zuwiderhandlungen verpflichten zu Schadenersatz. Alle Rechte fur den Fall der Patenterteilung oder GM-Eintragung vorbehalten freig.: HH released Copying of this document, disclosing it to third parties or using the contents there for any purposes without express written authorization by use illegally forbidden. Any offenders are liable to pay all relevant damages. Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vacuumschmelze: T60403-K5032-X102