QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Features Applications * * * * Telecommunications Data communications Wireless communications Servers, Workstations Benefits * High efficiency - no heat sink required * Higher current capability at 70 C than most competitors' 40 A half-bricks * RoHS lead-free solder and lead-solder-exempted products are available * Delivers up to 40 A * Outputs available: 3.3, 2.5, 1.8, 1.5, 1.2 and 1.0 V * Industry-standard quarter-brick pinout * On-board input differential LC-filter * Startup into pre-biased load * No minimum load required * Dimensions: 1.45" x 2.30" x 0.425" (36.83 x 58.42 x 10.80 mm) * Weight: 1.2 oz [34.2 g] * Meets Basic Insulation requirements of EN60950 * Withstands 100 V input transient for 100 ms * Fixed-frequency operation * Fully protected * Remote output sense * Non-Latching / Latching OTP option * Positive or negative logic ON/OFF option * Output voltage trim range: +10%/-20% with industry-standard trim equations (10% for 1.2 V and 1.0 V) * High reliability: MTBF = 13.9 million hours, calculated per Telcordia TR-332, Method I Case 1 * UL60950 recognized in US and Canada and DEMKO certified per IEC/EN60950 (pending) * Designed to meet Class B conducted emissions per FCC and EN55022 when used with external filter * All materials meet UL94, V-0 flammability rating Description The QME48T40 DC-DC Series of converters provide outstanding thermal performance in high temperature environments. This performance is accomplished through the use of patented/patent-pending circuits, packaging, and processing techniques to achieve ultra-high efficiency, excellent thermal management, and a low-body profile. The low-body profile and the preclusion of heat sinks minimize impedance to system airflow, thus enhancing cooling for both upstream and downstream devices. The use of 100% automation for assembly, coupled with advanced electronic circuits and thermal design, results in a product with extremely high reliability. Operating from a 36-75 V input, the QME48T40 converters provide any standard output voltage from 3.3 V down to 1.0 V that can be trimmed from -20% to +10% of the nominal output voltage (10% for output voltages 1.2 V and 1.0 V), thus providing outstanding design flexibility. ZD-02057 Rev. 4.1 www.power-one.com Page 1 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Electrical Specifications Conditions: TA = 25 C, Airflow = 300 LFM (1.5 m/s), Vi n = 48 VDC, unless otherwise specified. Parameter Notes Min Typ Max Units 80 VDC Absolute Maximum Ratings Input Voltage Continuous 0 Operating Ambient Temperature -40 85 C Storage Temperature -55 125 C Input Characteristics Operating Input Voltage Range 36 48 75 VDC Turn-on Threshold 33 34 35 VDC Turn-off Threshold 31 32 33 VDC 100 VDC VOUT = 3.3 VDC 4.1 ADC VOUT = 2.5 VDC 3.2 ADC VOUT = 1.8 VDC 2.4 ADC VOUT = 1.5 VDC 2.0 ADC VOUT = 1.2 VDC 1.6 ADC 1.4 ADC Input Under Voltage Lockout Input Voltage Transient 100 ms Maximum Input Current 40 ADC Out @ 36 VDC In VOUT = 1.0 VDC Input Stand-by Current Vin = 48V, converter disabled Input No Load Current (0 load on the output) Vin = 48V, converter enabled Input Reflected-Ripple Current, Input Voltage Ripple Rejection ZD-02057 Rev. 4.1 is 3 mA VOUT = 3.3 VDC 50 mA VOUT = 2.5 VDC 47 mA VOUT = 1.8 VDC 45 mA VOUT = 1.5 VDC 44 mA VOUT = 1.2 VDC 43 mA VOUT = 1.0 VDC 43 mA VOUT = 3.3 VDC 10 mAPK-PK VOUT = 2.5 VDC 9 mAPK-PK VOUT = 1.8 VDC 9 mAPK-PK VOUT = 1.5 VDC 9 mAPK-PK VOUT = 1.2 VDC 8 mAPK-PK VOUT = 1.0 VDC 8 mAPK-PK 120 Hz 60 dB Vin = 48V, 25 MHz bandwidth www.power-one.com Page 2 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Electrical Specifications (continued) Conditions: TA = 25 C, Airflow = 300 LFM (1.5 m/s), Vin = 48 VDC, unless otherwise specified. Parameter Notes Min Typ Max Units 40,000 F Output Characteristics External Load Capacitance Plus full load (resistive) Output Current Range 0 40 ADC 47 52 ADC Non-latching, Short = 10 m 50 60 Non-latching 9 Current Limit Inception Non-latching 42 Peak Short-Circuit Current RMS Short-Circuit Current Output Voltage Set Point (no load) VOUT = 3.3 VDC 3.267 3.300 3.333 VDC VOUT = 2.5 VDC 2.475 2.500 2.525 VDC VOUT = 1.8 VDC 1.782 1.800 1.818 VDC VOUT = 1.5 VDC 1.485 1.500 1.515 VDC VOUT = 1.2 VDC 1.188 1.200 1.212 VDC VOUT = 1.0 VDC 0.990 1.000 1.010 VDC 2 5 mV Output Regulation Over Line Output Regulation Over Load 2 Over line, load and temperature1 VOUT = 3.3 VDC Output Ripple and Noise - 25 MHz bandwidth Full load + 10 F tantalum + 1 F ceramic VOUT = 1.0 VDC Full load + 10 F tantalum + 1 F ceramic Output Voltage Range Dynamic Response Load Change 50%-75%-50% of Iout Max, di/dt = 0.1 A/s di/dt = 5 A/s Co = 1 F ceramic (Fig. 3.3V.9) Co = 470 F POS + 1 F ceramic 5 mV +1.5 %Vout 55 110 mVPK-PK 35 70 mVPK-PK -1.5 502 130 2 2 Settling Time to 1% of Vout A Arms mV mV 15 s VOUT = 3.3 VDC 91.0 % VOUT = 2.5 VDC 89.0 % VOUT = 1.8 VDC 86.5 % VOUT = 1.5 VDC 84.5 % VOUT = 1.2 VDC 82.0 % VOUT = 1.0 VDC % VOUT = 3.3 VDC 80.0 92.0 VOUT = 2.5 VDC 91.0 % VOUT = 1.8 VDC 88.5 % VOUT = 1.5 VDC 87.0 % VOUT = 1.2 VDC 85.0 % VOUT = 1.0 VDC 83.0 % Efficiency 100% Load 50% Load % Additional Notes: 1 2 3 Operating ambient temperature range of -40 C to 85 C for converter. See waveforms for dynamic response and settling time for different output voltages. Vout can be increased up to 10% via the sense leads or 10% via the trim function. However, the total output voltage trim from all sources should not exceed 10% of VOUT(NOM), in order to ensure specified operation of overvoltage protection circuitry ZD-02057 Rev. 4.1 www.power-one.com Page 3 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Electrical Specifications (continued) Conditions: TA = 25 C, Airflow = 300 LFM (1.5 m/s), Vin = 48 VDC, unless otherwise specified. Parameter Notes Min Typ Max Units Isolation Characteristics I/O Isolation 2000 Isolation Capacitance VDC 2 Isolation Resistance nF 10 M Feature Characteristics Switching Frequency 460 kHz Output Voltage Trim Range3 Non-latching (3.3 - 1.5 V) -20 +10 % Non-latching (1.2 V and 1.0 V) Percent of VOUT(NOM) -10 Remote Sense Compensation3 +10 +10 % % Output Overvoltage Protection Non-latching 117 140 % Auto-Restart Period Applies to all protection features Turn-On Time 128 200 ms 4 ms ON/OFF Control (Positive Logic) Converter Off (logic low) -20 0.8 VDC Converter On (logic high) 2.4 20 VDC ON/OFF Control (Negative Logic) Converter Off (logic high) 2.4 20 VDC Converter On (logic low) -20 0.8 VDC ZD-02057 Rev. 4.1 www.power-one.com Page 4 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Operations Input and Output Impedance These power converters have been designed to be stable with no external capacitors when used in low inductance input and output circuits. In many applications, the inductance associated with the distribution from the power source to the input of the converter can affect the stability of the converter. The addition of a 33 F electrolytic capacitor with an ESR < 1 across the input helps to ensure stability of the converter. In many applications, the user has to use decoupling capacitance at the load. The power converter will exhibit stable operation with external load capacitance up to 40,000 F on 3.3 V - 1.0 V outputs. Additionally, see the EMC section of this data sheet for discussion of other external components which may be required for control of conducted emissions. ON/OFF input, in which case it must be capable of sourcing or sinking up to 1 mA depending on the signal polarity. See the Startup Information section for system timing waveforms associated with use of the ON/OFF pin. Remote Sense (Pins 5 and 7) The remote sense feature of the converter compensates for voltage drops occurring between the output pins of the converter and the load. The SENSE(-) (Pin 5) and SENSE(+) (Pin 7) pins should be connected at the load or at the point where regulation is required (see Fig. B). QME Series Vin (+) (Top View) Vin Vin (+) QME Series Converter (Top View) ON/OFF Vin Vout (+) SENSE (+) TRIM Rload SENSE (-) Vin (-) Vout (-) CONTROL INPUT Fig. A: Circuit configuration for ON/OFF function. The positive logic version turns on when the ON/OFF pin is at a logic high and turns off when at a logic low. The converter is on when the ON/OFF pin is left open. See the Electrical Specifications for logic high/low definitions. 100 SENSE (+) ON/OFF TRIM Rload SENSE (-) 10 Vin (-) Vout (+) Rw ON/OFF (Pin 2) The ON/OFF pin is used to turn the power converter on or off remotely via a system signal. There are two remote control options available, positive and negative logic, with both referenced to Vin(-). A typical connection is shown in Fig. A. Rw Vout (+) Converter Fig. B: Remote sense circuit configuration. CAUTION If remote sensing is not utilized, the SENSE(-) pin must be connected to the Vout(-) pin (Pin 4), and the SENSE(+) pin must be connected to the Vout(+) pin (Pin 8) to ensure the converter will regulate at the specified output voltage. If these connections are not made, the converter will deliver an output voltage that is slightly higher than the specified data sheet value. Because the sense leads carry minimal current, large traces on the end-user board are not required. However, sense traces should be run side by side and located close to a ground plane to minimize system noise and ensure optimum performance. The converter's output overvoltage protection (OVP) senses the voltage across Vout(+) and Vout(-), and not across the sense lines, so the resistance (and resulting voltage drop) between the output pins of the converter and the load should be minimized to prevent unwanted triggering of the OVP. The negative logic version turns on when the pin is at a logic low and turns off when the pin is at a logic high. The ON/OFF pin can be hardwired directly to Vin(-) to enable automatic power up of the converter without the need of an external control signal. When utilizing the remote sense feature, care must be taken not to exceed the maximum allowable output power capability of the converter, which is equal to the product of the nominal output voltage and the allowable output current for the given conditions. The ON/OFF pin is internally pulled up to 5 V through a resistor. A properly debounced mechanical switch, open-collector transistor, or FET can be used to drive the input of the ON/OFF pin. The device must be capable of sinking up to 0.2 mA at a low level voltage of 0.8 V. An external voltage source (20 V maximum) may be connected directly to the When using remote sense, the output voltage at the converter can be increased by as much as 10% above the nominal rating in order to maintain the required voltage across the load. Therefore, the designer must, if necessary, decrease the maximum current (originally obtained from the derating curves) by the same percentage to ensure the converter's ZD-02057 Rev. 4.1 www.power-one.com Page 5 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output actual output power remains at or below the maximum allowable output power. Output Voltage Adjust /TRIM (Pin 6) The output voltage can be adjusted up 10% or down 20% for Vout 1.5 V, and 10% for Vout = 1.2 V and 1.0 V relative to the rated output voltage by the addition of an externally connected resistor. The TRIM pin should be left open if trimming is not being used. To minimize noise pickup, a 0.1 F capacitor is connected internally between the TRIM and SENSE(-) pins. To increase the output voltage, refer to Fig. C. A trim resistor, RT-INCR, should be connected between the TRIM (Pin 6) and SENSE(+) (Pin 7), with a value of: RT-INCR = 5.11(100 + )VO-NOM - 626 - 10.22 1.225 [k], 84.6 - 7.2 120 -9 RT-INCR = RT-DECR = 511 - 10.22 || RT-DECR = 700 - 15 || [k] (1.2 V) RT-DECR = 700 - 17 || [k] (1.0 V) RT-DECR = Required value of trim-down resistor [k] and is defined above. The above equations for calculation of trim resistor values match those typically used in conventional industry-standard quarter-bricks (except for 1.2 V and 1.0 V outputs). [k] (1.2 V) Vin (+) [k] (1.0 V) QME Series Converter (Top View) ON/OFF where, Vout (+) SENSE (+) TRIM SENSE (-) Vin (-) RT-INCR = Required value of trim-up resistor k] VO-NOM = Nominal value of output voltage [V] (VO -REQ - VO-NOM) X 100 VO -NOM [%] When trimming up, care must be taken not to exceed the converter`s maximum allowable output power. See the previous section for a complete discussion of this requirement. Vin (+) QME Series Converter (Top View) ON/OFF Rload R T-DECR Vout (-) Fig. D: Configuration for decreasing output voltage. VO-REQ = Desired (trimmed) output voltage [V]. Vin (3.3 - 1.5 V) where, Vin = [k] Note: for 3.3 - 1.5 V. RT-INCR = To decrease the output voltage (Fig. D), a trim resistor, RT-DECR, should be connected between the TRIM (Pin 6) and SENSE(-) (Pin 5), with a value of: Trimming/sensing beyond 110% of the rated output voltage is not an acceptable design practice, as this condition could cause unwanted triggering of the output overvoltage protection (OVP) circuit. The designer should ensure that the difference between the voltages across the converter's output pins and its sense pins does not exceed 10% of VOUT(NOM), or: [VOUT(+) - VOUT(-)] - [VSENSE(+) - VSENSE(-)] VO - NOM X 10% [V] This equation is applicable for any condition of output sensing and/or output trim. Vout (+) SENSE (+) R T-INCR TRIM Rload SENSE (-) Vin (-) Vout (-) Fig. C: Configuration for increasing output voltage. ZD-02057 Rev. 4.1 www.power-one.com Page 6 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Protection Features Safety Requirements Input Undervoltage Lockout Input undervoltage lockout is standard with this converter. The converter will shut down when the input voltage drops below a pre-determined voltage. The input voltage must be typically 34 V for the converter to turn on. Once the converter has been turned on, it will shut off when the input voltage drops typically below 32 V. This feature is beneficial in preventing deep discharging of batteries used in telecom applications. The converters meet North American and International safety regulatory requirements per UL60950 and EN60950 (pending). Basic Insulation is provided between input and output. To comply with safety agencies' requirements, an input line fuse must be used external to the converter. The Table below provides the recommended fuse rating for use with this family of products. Output Overcurrent Protection (OCP) The converter is protected against overcurrent or short circuit conditions. Upon sensing an overcurrent condition, the converter will switch to constant current operation and thereby begin to reduce output voltage. When the output voltage drops below 60% of the nominal value of output voltage, the converter will shut down. Once the converter has shut down, it will attempt to restart nominally every 200 ms with a typical 3-5% duty cycle. The attempted restart will continue indefinitely until the overload or short circuit conditions are removed or the output voltage rises above 40-50% of its nominal value. Once the output current is brought back into its specified range, the converter automatically exits the hiccup mode and continues normal operation. Output Overvoltage Protection (OVP) The converter will shut down if the output voltage across Vout(+) (Pin 8) and Vout(-) (Pin 4) exceeds the threshold of the OVP circuitry. The OVP circuitry contains its own reference, independent of the output voltage regulation loop. Once the converter has shut down, it will attempt to restart every 200 ms until the OVP condition is removed. Overtemperature Protection (OTP) The converter will shut down under an overtemperature condition to protect itself from overheating caused by operation outside the thermal derating curves, or operation in abnormal conditions such as system fan failure. After the converter has cooled to a safe operating temperature, it will automatically restart. ZD-02057 Rev. 4.1 Output Voltage 3.3 V 2.5 V, 1.8 V 1.5 V, 1.2 V, 1.0 V Fuse Rating 7.5 A 5A 3A All QME converters are UL approved (pending) for a maximum fuse rating of 15 Amps. To protect a group of converters with a single fuse, the rating can be increased from the recommended value above. Electromagnetic Compatibility (EMC) EMC requirements must be met at the end-product system level, as no specific standards dedicated to EMC characteristics of board mounted component dc-dc converters exist. However, Power-One tests its converters to several system level standards, primary of which is the more stringent EN55022, Information technology equipment Radio disturbance characteristics-Limits and methods of measurement. An effective internal LC differential filter significantly reduces input reflected ripple current, and improves EMC. With the addition of a simple external filter, all versions of the QME-Series of converters pass the requirements of Class B conducted emissions per EN55022 and FCC requirements. Please contact Power-One Applications Engineering for details of this testing. www.power-one.com Page 7 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output V IN Startup Information (using negative ON/OFF) Scenario #1: Initial Startup From Bulk Supply ON/OFF function enabled, converter started via application of VIN. See Figure E. Time Comments t0 ON/OFF pin is ON; system front end power is toggled on, VIN to converter begins to rise. t1 VIN crosses undervoltage Lockout protection circuit threshold; converter enabled. t2 Converter begins to respond to turn-on command (converter turn-on delay). t3 Converter VOUT reaches 100% of nominal value. For this example, the total converter startup time (t3- t1) is typically 4 ms. Scenario #2: Initial Startup Using ON/OFF Pin With VIN previously powered, converter started via ON/OFF pin. See Figure F. Time Comments t0 VINPUT at nominal value. t1 Arbitrary time when ON/OFF pin is enabled (converter enabled). t2 End of converter turn-on delay. t3 Converter VOUT reaches 100% of nominal value. For this example, the total converter startup time (t3- t1) is typically 4 ms. ON/OFF STATE OFF ON V OUT t0 t1 t2 t t3 Fig. E: Startup scenario #1. VIN ON/OFF STATE OFF ON VOUT Scenario #3: Turn-off and Restart Using ON/OFF Pin With VIN previously powered, converter is disabled and then enabled via ON/OFF pin. See Figure G. Time Comments t0 VIN and VOUT are at nominal values; ON/OFF pin ON. t1 ON/OFF pin arbitrarily disabled; converter output falls to zero; turn-on inhibit delay period (200 ms typical) is initiated, and ON/OFF pin action is internally inhibited. t2 ON/OFF pin is externally re-enabled. If (t2- t1) 200 ms, external action of ON/OFF pin is locked out by startup inhibit timer. If (t2- t1) > 200 ms, ON/OFF pin action is internally enabled. t3 Turn-on Inhibit delay period ends. If ON/OFF pin is ON, converter begins turn-on; if off, converter awaits ON/OFF pin ON signal; see Figure F. t4 End of converter turn-on delay. t5 Converter VOUT reaches 100% of nominal value. For the condition, (t2- t1) 200 ms, the total converter startup time (t5- t2) is typically 204 ms. For (t2- t1) > 200 ms, startup will be typically 4 ms after release of ON/OFF pin. t0 t1 t2 t t3 Fig. F: Startup scenario #2. VIN 200 ms ON/OFF STATE OFF ON VOUT t0 t1 t2 t3 t4 t t5 Fig. G: Startup scenario #3. ZD-02057 Rev. 4.1 www.power-one.com Page 8 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Thermal Derating Characterization General Information The converter has been characterized for many operational aspects, to include thermal derating (maximum load current as a function of ambient temperature and airflow) for vertical and horizontal mountings, efficiency, startup and shutdown parameters, output ripple and noise, transient response to load step-change, overload, and short circuit. The following pages contain specific plots or waveforms associated with the converter. Additional comments for specific data are provided below. Test Conditions All data presented were taken with the converter soldered to a test board, specifically a 0.060" thick printed wiring board (PWB) with four layers. The top and bottom layers were not metalized. The two inner layers, comprised of two-ounce copper, were used to provide traces for connectivity to the converter. The lack of metalization on the outer layers as well as the limited thermal connection ensured that heat transfer from the converter to the PWB was minimized. This provides a worst-case but consistent scenario for thermal derating purposes. All measurements requiring airflow were made in the vertical and horizontal wind tunnel using Infrared (IR) thermography and thermocouples for thermometry. Ensuring components on the converter do not exceed their ratings is important to maintaining high reliability. If one anticipates operating the converter at or close to the maximum loads specified in the derating curves, it is prudent to check actual operating temperatures in the application. Thermographic imaging is preferable; if this capability is not available, then thermocouples may be used. The use of AWG #40 gauge thermocouples is recommended to ensure measurement accuracy. Careful routing of the thermocouple leads will further minimize measurement error. Refer to Fig. H for the optimum measuring thermocouple locations. Load current vs. ambient temperature and airflow rates are given in Fig. x.1 and Fig. x.2 for vertical and horizontal converter mountings. Ambient temperature was varied between 25 C and 85 C, with airflow rates from 30 to 500 LFM (0.15 to 2.5 m/s). For each set of conditions, the maximum load current was defined as the lowest of: (i) The output current at which any FET junction temperature does not exceed a maximum specified temperature of 120 C as indicated by the thermographic image, or (ii) The nominal rating of the converter (40 A). During normal operation, derating curves with maximum FET temperature less or equal to 120 C should not be exceeded. Temperature on the PCB at thermocouple locations shown in Fig. H should not exceed 120 C in order to operate inside the derating curves. Efficiency Fig. x.3 shows the efficiency vs. load current plot for ambient temperature of 25 C, airflow rate of 300 LFM (1.5 m/s) with horizontal mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of efficiency vs. load current, as a function of ambient temperature with Vin = 48 V, airflow rate of 200 LFM (1 m/s) with horizontal mounting is shown in Fig. x.4. Power Dissipation Fig. x.5 shows the power dissipation vs. load current plot for Ta = 25 C, airflow rate of 300 LFM (1.5 m/s) with horizontal mounting and input voltages of 36 V, 48 V and 72 V. Also, a plot of power dissipation vs. load current, as a function of ambient temperature with Vin = 48 V, airflow rate of 200 LFM (1 m/s) with horizontal mounting is shown in Fig. x.6. Startup Output voltage waveforms, during the turn-on transient using the ON/OFF pin for full rated load currents (resistive load) are shown without and with external load capacitance in Figs. x.7-8, respectively. Ripple and Noise Fig. x.11 show the output voltage ripple waveform, measured at full rated load current with a 10 F tantalum and 1 F ceramic capacitor across the output. Note that all output voltage waveforms are measured across a 1 F ceramic capacitor. Fig. H: Locations of the thermocouple for thermal testing. ZD-02057 Rev. 4.1 The input reflected ripple current waveforms are obtained using the test setup shown in Fig x.12. The corresponding waveforms are shown in Figs. x.13-14. www.power-one.com Page 9 of 35 50 50 40 40 Load Current [Adc] Load Current [Adc] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 0 0 20 30 40 50 60 70 80 20 90 30 40 50 60 70 80 90 Ambient Temperature [C] Ambient Temperature [C] Fig. 3.3V.1: Available load current vs. ambient air temperature and airflow rates for QME48T40033 converter with G height pins mounted vertically with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. Fig. 3.3V.2: Available load current vs. ambient air temperature and airflow rates for QME48T40033 converter with G height pins mounted horizontally with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. 0.95 0.95 0.90 0.90 Efficiency Efficiency Note: NC - Natural convection 0.85 72 V 48 V 36 V 0.80 8 16 24 32 40 48 0.75 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 3.3V.3: Efficiency vs. load current and input voltage for QME48T40033 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. ZD-02057 Rev. 4.1 70 C 55 C 40 C 0.80 0.75 0 0.85 Fig. 3.3V.4: Efficiency vs. load current and ambient temperature for QME48T40033 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). www.power-one.com Page 10 of 35 18.00 18.00 15.00 15.00 Power Dissipation [W] Power Dissipation [W] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 12.00 9.00 6.00 72 V 48 V 36 V 3.00 12.00 9.00 6.00 70 C 55 C 40 C 3.00 0.00 0.00 0 5 10 15 20 25 30 35 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 3.3V.5: Power dissipation vs. load current and input voltage for QME48T40033 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 3.3V.6: Power dissipation vs. load current and ambient temperature for QME48T40033 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). Fig. 3.3V.7: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 3.3V.8: Turn-on transient at full rated load current (resistive) plus 10,000 F at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. ZD-02057 Rev. 4.1 www.power-one.com Page 11 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 3.3V.9: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 0.1 A/s. Co = 1 F ceramic. Time scale: 0.2 ms/div. Fig. 3.3V.10: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 5 A/s. Co = 470 F POS + 1 F ceramic. Time scale: 0.2 ms/div. iS 10 H source inductance Vsource Fig. 3.3V.11: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with Co = 10 F tantalum + 1 F ceramic and Vin = 48 V. Time scale: 1 s/div. ZD-02057 Rev. 4.1 iC 33 F ESR <1 electrolytic capacitor QME Series DC/DC Converter 1 F ceramic capacitor Vout Fig. 3.3V.12: Test setup for measuring input reflected ripple currents, ic and is. www.power-one.com Page 12 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 3.3V.13: Input reflected ripple current, ic (100 mA/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 3.3V.12 for test setup. Time scale: 1 s/div. Fig. 3.3V.14: Input reflected ripple current, is (10 mA/div.), measured through 10 H at the source at full rated load current and Vin = 48 V. Refer to Fig. 3.3V.12 for test setup. Time scale: 1 s/div. Fig. 3.3V.15: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 3.3V.16: Load current (top trace, 20 A/div., 50 ms/div.) into a 10 m short circuit during restart, at Vin = 48 V. Bottom trace (20 A/div., 2 ms/div.) is an expansion of the on-time portion of the top trace. ZD-02057 Rev. 4.1 www.power-one.com Page 13 of 35 50 50 40 40 Load Current [Adc] Load Current [Adc] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 0 0 20 30 40 50 60 70 80 90 20 30 40 Ambient Temperature [C] 50 60 70 80 90 Ambient Temperature [C] Fig. 2.5V.1: Available load current vs. ambient air temperature and airflow rates for QME48T40025 converter with G height pins mounted vertically with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. Fig. 2.5V.2: Available load current vs. ambient air temperature and airflow rates for QME48T40025 converter with G height pins mounted horizontally with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. 0.95 0.95 0.90 0.90 0.85 0.85 Efficiency Efficiency Note: NC - Natural convection 0.80 72 V 48 V 36 V 0.75 8 16 24 32 40 48 0.70 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 2.5V.3: Efficiency vs. load current and input voltage for QME48T40025 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. ZD-02057 Rev. 4.1 70 C 55 C 40 C 0.75 0.70 0 0.80 Fig. 2.5V.4: Efficiency vs. load current and ambient temperature for QME48T40025 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). www.power-one.com Page 14 of 35 18.00 18.00 15.00 15.00 Power Dissipation [W] Power Dissipation [W] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 12.00 9.00 6.00 72 V 48 V 36 V 3.00 12.00 9.00 6.00 70 C 55 C 40 C 3.00 0.00 0.00 0 8 16 24 32 40 48 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 2.5V.5: Power dissipation vs. load current and input voltage for QME48T40025 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 2.5V.6: Power dissipation vs. load current and ambient temperature for QME48T40025 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). Fig. 2.5V.7: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 2.5V.8: Turn-on transient at full rated load current (resistive) plus 10,000 F at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. ZD-02057 Rev. 4.1 www.power-one.com Page 15 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 2.5V.9: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 0.1 A/s. Co = 1 F ceramic. Time scale: 0.2 ms/div. Fig. 2.5V.10: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 5A/s. Co = 470 F POS + 1 F ceramic. Time scale: 0.2 ms/div. iS 10 H source inductance Vsource Fig. 2.5V.11: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with Co = 10 F tantalum + 1 F ceramic and Vin = 48 V. Time scale: 1 s/div. ZD-02057 Rev. 4.1 iC 33 F ESR <1 electrolytic capacitor QME Series DC/DC Converter 1 F ceramic capacitor Vout Fig. 2.5V.12: Test setup for measuring input reflected ripple currents, ic and is. www.power-one.com Page 16 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 2.5V.13: Input reflected ripple current, ic (100 mA/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 2.5V.12 for test setup. Time scale: 1 s/div. Fig. 2.5V.14: Input reflected ripple current, is (10 mA/div.), measured through 10 H at the source at full rated load current and Vin = 48 V. Refer to Fig. 2.5V.12 for test setup. Time scale: 1 s/div. Fig. 2.5V.15: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 2.5V.16: Load current (top trace, 20 A/div., 50 ms/div.) into a 10 m short circuit during restart, at Vin = 48 V. Bottom trace (20 A/div., 2 ms/div.) is an expansion of the on-time portion of the top trace. ZD-02057 Rev. 4.1 www.power-one.com Page 17 of 35 50 50 40 40 Load Current [Adc] Load Current [Adc] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 0 0 20 30 40 50 60 70 80 90 20 30 40 Ambient Temperature [C] 50 60 70 80 90 Ambient Temperature [C] Fig. 1.8V.1: Available load current vs. ambient air temperature and airflow rates for QME48T40018 converter with G height pins mounted vertically with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. Fig. 1.8V.2: Available load current vs. ambient air temperature and airflow rates for QME48T40018 converter with G height pins mounted horizontally with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. 0.95 0.95 0.90 0.90 0.85 0.85 Efficiency Efficiency Note: NC - Natural convection 0.80 0.75 72 V 48 V 36 V 0.80 0.75 0.70 70 C 55 C 40 C 0.70 0.65 0 8 16 24 32 40 48 0.65 0 Load Current [Adc] 16 24 32 40 48 Load Current [Adc] Fig. 1.8V.3: Efficiency vs. load current and input voltage for QME48T40018 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. ZD-02057 Rev. 4.1 8 Fig. 1.8V.4: Efficiency vs. load current and ambient temperature for QME48T40018 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). www.power-one.com Page 18 of 35 15.00 15.00 12.00 12.00 Power Dissipation [W] Power Dissipation [W] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 9.00 6.00 72 V 48 V 36 V 3.00 9.00 6.00 70 C 55 C 40 C 3.00 0.00 0.00 0 8 16 24 32 40 48 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 1.8V.5: Power dissipation vs. load current and input voltage for QME48T40018 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 1.8V.6: Power dissipation vs. load current and ambient temperature for QME48T40018 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). Fig. 1.8V.7: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 1.8V.8: Turn-on transient at full rated load current (resistive) plus 10,000 F at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. ZD-02057 Rev. 4.1 www.power-one.com Page 19 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.8V.9: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 0.1 A/s. Co = 1 F ceramic. Time scale: 0.2 ms/div. Fig. 1.8V.10: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 5 A/s. Co = 470 F POS + 1 F ceramic. Time scale: 0.2 ms/div. iS 10 H source inductance Vsource Fig. 1.8V.11: Output voltage ripple (20mV/div.) at full rated load current into a resistive load with Co = 10 F tantalum + 1 F ceramic and Vin = 48 V. Time scale: 1 s/div. ZD-02057 Rev. 4.1 iC 33 F ESR <1 electrolytic capacitor QME Series DC/DC Converter 1 F ceramic capacitor Vout Fig. 1.8V.12: Test setup for measuring input reflected ripple currents, ic and is. www.power-one.com Page 20 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.8V.13: Input reflected ripple current, ic (100 mA/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.8V.12 for test setup. Time scale: 1 s/div. Fig. 1.8V.14: Input reflected ripple current, is (10 mA/div.), measured through 10 H at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.8V.12 for test setup. Time scale: 1 s/div. Fig. 1.8V.15: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.8V.16: Load current (top trace, 20 A/div., 50 ms/div.) into a 10 m short circuit during restart, at Vin = 48 V. Bottom trace (20 A/div., 2 ms/div.) is an expansion of the on-time portion of the top trace. ZD-02057 Rev. 4.1 www.power-one.com Page 21 of 35 50 50 40 40 Load Current [Adc] Load Current [Adc] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 0 0 20 30 40 50 60 70 80 90 20 30 40 Ambient Temperature [C] 50 60 70 80 90 Ambient Temperature [C] Fig. 1.5V.1: Available load current vs. ambient air temperature and airflow rates for QME48T40015 converter with G height pins mounted vertically with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. Fig. 1.5V.2: Available load current vs. ambient air temperature and airflow rates for QME48T40015 converter with G height pins mounted horizontally with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. 0.95 0.95 0.90 0.90 0.85 0.85 Efficiency Efficiency Note: NC - Natural convection 0.80 0.75 72 V 48 V 36 V 0.70 0.80 0.75 70 C 55 C 40 C 0.70 0.65 0.65 0.60 0 8 16 24 32 40 48 0.60 0 Load Current [Adc] 16 24 32 40 48 Load Current [Adc] Fig. 1.5V.3: Efficiency vs. load current and input voltage for QME48T40015 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. ZD-02057 Rev. 4.1 8 Fig. 1.5V.4: Efficiency vs. load current and ambient temperature for QME48T40015 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). www.power-one.com Page 22 of 35 15.00 15.00 12.00 12.00 Power Dissipation [W] Power Dissipation [W] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 9.00 6.00 72 V 48 V 36 V 3.00 9.00 6.00 70 C 55 C 40 C 3.00 0.00 0.00 0 8 16 24 32 40 48 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 1.5V.5: Power dissipation vs. load current and input voltage for QME48T40015 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 1.5V.6: Power dissipation vs. load current and ambient temperature for QME48T40015 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). Fig. 1.5V.7: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 1.5V.8: Turn-on transient at full rated load current (resistive) plus 10,000 F at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. ZD-02057 Rev. 4.1 www.power-one.com Page 23 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.5V.9: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 0.1 A/s. Co = 1 F ceramic. Time scale: 0.2 ms/div. Fig. 1.5V.10: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 5A/s. Co = 470 F POS + 1 F ceramic. Time scale: 0.2 ms/div. iS 10 H source inductance Vsource Fig. 1.5V.11: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with Co = 10 F tantalum + 1 F ceramic and Vin = 48 V. Time scale: 1 s/div. ZD-02057 Rev. 4.1 iC 33 F ESR <1 electrolytic capacitor QME Series DC/DC Converter 1 F ceramic capacitor Vout Fig. 1.5V.12: Test setup for measuring input reflected ripple currents, ic and is. www.power-one.com Page 24 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.5V.13: Input reflected ripple current, ic (100 mA/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.5V.12 for test setup. Time scale: 1 s/div. Fig. 1.5V.14: Input reflected ripple current, is (10 mA/div.), measured through 10 H at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.5V.12 for test setup. Time scale: 1 s/div. Fig. 1.5V.15: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.5V.16: Load current (top trace, 20 A/div., 50 ms/div.) into a 10 m short circuit during restart, at Vin = 48 V. Bottom trace (20 A/div., 2 ms/div.) is an expansion of the on-time portion of the top trace. ZD-02057 Rev. 4.1 www.power-one.com Page 25 of 35 50 50 40 40 Load Current [Adc] Load Current [Adc] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 0 0 20 30 40 50 60 70 80 90 20 30 40 Ambient Temperature [C] 50 60 70 80 90 Ambient Temperature [C] Fig. 1.2V.1: Available load current vs. ambient air temperature and airflow rates for QME48T40012 converter with G height pins mounted vertically with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. Fig. 1.2V.2: Available load current vs. ambient air temperature and airflow rates for QME48T40012 converter with G height pins mounted horizontally with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. 0.90 0.90 0.85 0.85 0.80 0.80 Efficiency Efficiency Note: NC - Natural convection 0.75 0.70 72 V 48 V 36 V 0.75 0.70 0.65 70 C 55 C 40 C 0.65 0.60 0 8 16 24 32 40 48 0.60 0 Load Current [Adc] 16 24 32 40 48 Load Current [Adc] Fig. 1.2V.3: Efficiency vs. load current and input voltage for QME48T40012 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. ZD-02057 Rev. 4.1 8 Fig. 1.2V.4: Efficiency vs. load current and ambient temperature for QME48T40012 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). www.power-one.com Page 26 of 35 15.00 15.00 12.00 12.00 Power Dissipation [W] Power Dissipation [W] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 9.00 6.00 72 V 48 V 36 V 3.00 9.00 6.00 70 C 55 C 40 C 3.00 0.00 0.00 0 8 16 24 32 40 48 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 1.2V.5: Power dissipation vs. load current and input voltage for QME48T40012 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 1.2V.6: Power dissipation vs. load current and ambient temperature for QME48T40012 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). Fig. 1.2V.7: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 1.2V.8: Turn-on transient at full rated load current (resistive) plus 10,000 F at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. ZD-02057 Rev. 4.1 www.power-one.com Page 27 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.2V.9: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 0.1 A/s. Co = 1 F ceramic. Time scale: 0.2 ms/div. Fig. 1.2V.10: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 5 A/s. Co = 470 F POS + 1 F ceramic. Time scale: 0.2 ms/div. iS 10 H source inductance Vsource Fig. 1.2V.11: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with Co = 10 F tantalum + 1 F ceramic and Vin = 48 V. Time scale: 1 s/div. ZD-02057 Rev. 4.1 iC 33 F ESR <1 electrolytic capacitor QME Series DC/DC Converter 1 F ceramic capacitor Vout Fig. 1.2V.12: Test setup for measuring input reflected ripple currents, ic and is. www.power-one.com Page 28 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.2V.13: Input reflected ripple current, ic (100 mA/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.2V.12 for test setup. Time scale: 1 s/div. Fig. 1.2V.14: Input reflected ripple current, is (10 mA/div.), measured through 10 H at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.2V.12 for test setup. Time scale: 1 s/div. Fig. 1.2V.15: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.2V.16: Load current (top trace, 20 A/div., 50 ms/div.) into a 10 m short circuit during restart, at Vin = 48 V. Bottom trace (20 A/div., 5 ms/div.) is an expansion of the on-time portion of the top trace. ZD-02057 Rev. 4.1 www.power-one.com Page 29 of 35 50 50 40 40 Load Current [Adc] Load Current [Adc] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 30 500 LFM (2.5 m/s) 400 LFM (2.0 m/s) 300 LFM (1.5 m/s) 200 LFM (1.0 m/s) 100 LFM (0.5 m/s) NC - 30 LFM (0.15 m/s) 20 10 0 0 20 30 40 50 60 70 80 90 20 30 40 Ambient Temperature [C] 50 60 70 80 90 Ambient Temperature [C] Fig. 1.0V.1: Available load current vs. ambient air temperature and airflow rates for QME48T40010 converter with G height pins mounted vertically with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. Fig. 1.0V.2: Available load current vs. ambient air temperature and airflow rates for QME48T40010 converter with G height pins mounted horizontally with air flowing from pin 1 to pin 3, MOSFET temperature 120 C, Vin = 48 V. 0.90 0.85 0.80 0.80 Efficiency Efficiency Note: NC - Natural convection 0.70 72 V 48 V 36 V 0.60 8 16 24 32 40 48 0.65 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 1.0V.3: Efficiency vs. load current and input voltage for QME48T40010 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. ZD-02057 Rev. 4.1 70 C 55 C 40 C 0.70 0.50 0 0.75 Fig. 1.0V.4: Efficiency vs. load current and ambient temperature for QME48T40010 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). www.power-one.com Page 30 of 35 15.00 15.00 12.00 12.00 Power Dissipation [W] Power Dissipation [W] QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output 9.00 6.00 72 V 48 V 36 V 3.00 9.00 6.00 70 C 55 C 40 C 3.00 0.00 0.00 0 8 16 24 32 40 48 0 Load Current [Adc] 8 16 24 32 40 48 Load Current [Adc] Fig. 1.0V.5: Power dissipation vs. load current and input voltage for QME48T40010 converter mounted horizontally with air flowing from pin 1 to pin 3 at a rate of 300 LFM (1.5 m/s) and Ta = 25 C. Fig. 1.0V.6: Power dissipation vs. load current and ambient temperature for QME48T40010 converter mounted horizontally with Vin = 48 V and air flowing from pin 1 to pin 3 at a rate of 200 LFM (1.0 m/s). Fig. 1.0V.7: Turn-on transient at full rated load current (resistive) with no output capacitor at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. Fig. 1.0V.8: Turn-on transient at full rated load current (resistive) plus 10,000 F at Vin = 48 V, triggered via ON/OFF pin. Top trace: ON/OFF signal (5 V/div.). Bottom trace: output voltage (1 V/div.). Time scale: 2 ms/div. ZD-02057 Rev. 4.1 www.power-one.com Page 31 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.0V.9: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 0.1 A/s. Co = 1 F ceramic. Time scale: 0.2 ms/div. Fig. 1.0V.10: Output voltage response to load current step-change (20 A - 30 A - 20 A) at Vin = 48 V. Top trace: output voltage (100 mV/div.). Bottom trace: load current (10 A/div.). Current slew rate: 5 A/s. Co = 470 F POS + 1 F ceramic. Time scale: 0.2 ms/div. iS 10 H source inductance Vsource Fig. 1.0V.11: Output voltage ripple (20 mV/div.) at full rated load current into a resistive load with Co = 10 F tantalum + 1 F ceramic and Vin = 48 V. Time scale: 1 s/div. ZD-02057 Rev. 4.1 iC 33 F ESR <1 electrolytic capacitor QME Series DC/DC Converter 1 F ceramic capacitor Vout Fig. 1.0V.12: Test setup for measuring input reflected ripple currents, ic and is. www.power-one.com Page 32 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Fig. 1.0V.13: Input reflected ripple current, ic (100 mA/div.), measured at input terminals at full rated load current and Vin = 48 V. Refer to Fig. 1.0V.12 for test setup. Time scale: 1 s/div. Fig. 1.0V.14: Input reflected ripple current, is (10 mA/div.), measured through 10 H at the source at full rated load current and Vin = 48 V. Refer to Fig. 1.0V.12 for test setup. Time scale: 1 s/div. Fig. 1.0V.15: Output voltage vs. load current showing current limit point and converter shutdown point. Input voltage has almost no effect on current limit characteristic. Fig. 1.0V.16: Load current (top trace, 20 A/div., 50 ms/div.) into a 10 m short circuit during restart, at Vin = 48 V. Bottom trace (20 A/div., 5 ms/div.) is an expansion of the on-time portion of the top trace. ZD-02057 Rev. 4.1 www.power-one.com Page 33 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Physical Information QME48T Pinout (Through-hole) Pad/Pin Connections 1 Pad/Pin # 1 2 3 4 5 6 7 8 8 7 2 TOP VIEW 6 5 3 4 SIDE VIEW Function Vin (+) ON/OFF Vin (-) Vout (-) SENSE(-) TRIM SENSE(+) Vout (+) QME48T Platform Notes * * * * * Height Option G HT (Max. Height) 0.425 [10.80] CL (Min. Clearance) 0.035 [0.89] Pin Option A B ZD-02057 Rev. 4.1 All dimensions are in inches [mm] Pins 1-3 and 5-7 are O 0.040" [1.02] with O 0.078" [1.98] shoulder Pins 4 and 8 are O 0.062" [1.57] without shoulder Pin Material & Finish: Brass Alloy 360 with Matte Tin over Nickel Converter Weight: 1.2 oz [34.2 g] typical PL Pin Length 0.005 [0.13] 0.188 [4.78] 0.145 [3.68] www.power-one.com Page 34 of 35 QME48T40 DC-DC Series Data Sheet 36-75 VDC Input; 1.0-3.3 VDC @ 40A Output Heatsink Option S1 HT (Max. Height) 0.99 [25.1] Pin Option B CL (Min. 0.039 [1.00] PL Pin Length 0.005 [0.13] 0.145 [3.68] Converter Part Numbering Ordering Information Product Series Input Voltage Mounting Scheme Rated Load Current Output Voltage QME 48 T 40 033 QuarterBrick Format 36-75 V T Throughhole - 010 1.0V 012 1.2V 015 1.5V 40 ADC 018 1.8V 025 2.5V 033 3.3V ON/OFF Logic Max Height [HT] Pin Length [PL] Special Feature s N G B 0 Through hole 0 STD NonLatching N Negative Through hole P Positive G 0.425" A 0.188" B 0.145" L Latching Option RoHS No Suffix RoHS lead-solderexemption compliant G RoHS compliant for all six substances Heatsink No Suffix No heatsink -S1 Heatsink as shown Example: The example above describes P/N QME48T40033-NGB0: 36-75 V input, through-hole, 40 A @ 3.3 V output, negative ON/OFF logic, a 0.145" solder tail and maximum height of 0.425", standard (non-latching) protection, and Eutectic Tin/Lead solder. Consult factory for the complete list of available options. Attention: The heatsink option "S1" is only available with the model QME48T40033-NGBOG-S1 Notes: 1. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. 2. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. ZD-02057 Rev. 4.1 www.power-one.com Page 35 of 35