PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output Features * Best-in-class, "Platinum level" efficiency * Wide input voltage range: 40 - 72 VDC * Always-On 16.5W programmable standby output (3.3/5 V) * Hot-plug capable * Parallel operation with active digital current sharing * High density design: 25.6 W/in3 * Small form factor: 54.5 x 40.0 x 321.5 mm * I2C communication interface for control, programming and monitoring with PSMI and PMBusTM protocol * Overtemperature, output overvoltage and overcurrent protection * 256 Bytes of EEPROM for user information * 2 Status LEDs: IN OK and OUT OK with fault signaling Applications * High performance servers, routers, and switches. Description The PFE1100-12-054ND is an 1100 watt DC to DC power supply that converts DC input into a main output of 12 VDC for powering intermediate bus architectures (IBA) in high performance and reliability servers, routers, and network switches. The PFE1100-12-054ND meets international safety standards and displays the CE-Mark for the European Low Voltage Directive (LVD). 96 95 Efficiency [%] 94 93 92 91 Vi = 40Vdc, fan external 90 Vi = 53Vdc, fan external 89 Vi = 72Vdc, fan external Platinum 88 87 0 10 20 30 40 50 60 70 80 90 100 Po [% nom] ORDERING INFORMATION PFE 1100 - 12 - 054 Product Family PFE Front-Ends Power Level 1100W Dash V1 Output 12V Dash Width 54mm BCD.00034 Rev. AC, 10-July-2012 Page 1 / 9 N D Airflow Input N: normal A: AC R: reversed D: DC www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output 1 ENVIRONMENTAL AND MECHANICAL Parameter TA Ambient temperature TAext Extended temp. range TS Na Storage temperature Audible noise Dimensions M Conditions / Description Vi min to Vi max, I1 nom, ISB nom Derated output Vi min to Vi max / I1 < 77A, ISB nom Vi min to Vi max / I1 < 35A, ISB nom Non-operational Sound power at Vi nom, 50% Io nom, TA = 25C Width Height Depth Min 0 +45 Nom -20 Max +45 +65 +55 +65 +70 Unit C C C C C dBA mm mm mm kg Max 62 54.5 40.0 321.5 1.12 Weight 2 INPUT SPECIFICATIONS General Condition: TA = 0... 45 C unless otherwise noted. Parameter Vi nom Nominal input voltage Vi Input voltage ranges Ii max Max input current Ii p Inrush Current Limitation Vi on Vi off 1) Turn-on input voltage1) Turn-off input voltage1) Efficiency without fan Thold Hold-up Time Conditions / Description Min Nom 53 Normal operating (Vi min to Vi max) 40 72 33 60 Unit VDC VDC Arms Ap 42 37 45 40 VDC VDC Vi min to Vi max Ramping up Ramping down Vi nom, 0.1Ix nom, Vx nom, TA = 25 C Vi nom, 0.2Ix nom, Vx nom, TA = 25 C Vi nom, 0.5Ix nom, Vx nom, TA = 25 C Vi nom, Ix nom, Vx nom, TA = 25 C V1 > 10.8 V, VSB within regulation, Vi = 53 VDC, Px nom 89.3 93.5 95 92.9 5 % ms The Front-End is provided with a minimum hysteresis of 3 V during turn-on and turn-off within the ranges. BCD.00034 Rev. AC, 10-July-2012 Page 2 / 9 www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output 3 OUTPUT SPECIFICATIONS General Condition: Ta = 0 ... +45 C unless otherwise noted. Parameter Main Output V1 V1 nom Nominal output voltage V1 set Output setpoint accuracy dV1 tot Total regulation P1 nom Nominal output power I1 nom Nominal output current v1 pp Output ripple voltage dV1 Load Load regulation dV1 Line Line regulation I1 max Current limitation dIshare Current sharing dVdyn Dynamic load regulation Trec Recovery time tAC V1 Start-up time from DC tV1 rise Rise time CLoad Capacitive loading Standby Output VSB VSB nom Nominal output voltage VSB set Output setpoint accuracy dVSB tot Total regulation PSB nom Nominal output power ISB nom Nominal output current VSB pp Output ripple voltage dVSB Droop ISB max Current limitation dVSBdyn Dynamic load regulation Trec Recovery time tAC VSB Start-up time from DC input Parameter Standby Output VSB (Cont.) BCD.00034 Rev. AC, 10-July-2012 Conditions / Description 0.5 I1 nom, Tamb = 25 C Vi min to Vi max, 0 to 100% I1 nom, Ta min to Ta max V1 = 12 VDC V1 = 12 VDC V1 nom, I1 nom, 20 MHz BW, 10nF/16V/X7R/1210 + 10uF/16V at V1 Vi = Vi nom, 0 - 100 % I1 nom Min V1 = 10.8 VDC V1 = 10...90% V1 nom Ta = 25 C VSB_SEL = 1 0.5 ISB nom, Tamb = 25 C VSB_SEL = 0 VSB_SEL = 0 / 1 Vi min to Vi max, 0 to 100% ISB nom, Ta min to Ta max VSB_SEL = 0 / 1 VSB = 3.3 VDC VSB = 5.0 VDC VSB nom, ISB nom, 20 MHz BW, 10nF/16V/X7R/1210 + 10uF/16V at VSB VSB_SEL = 1 0 - 100 % ISB nom VSB_SEL = 0 VSB_SEL = 1 VSB_SEL = 0 ISB = 50% ISB nom, ISB = 5 ... 100% ISB nom, dIo/dt = 0.5 A/s, recovery within 1% of V1 nom VSB = 90% VSB nom Conditions / Description Page 3 / 9 Max 12.0 -0.5 -1 150 105 +3 0.6 1 2 10 10 000 mV mV ADC A V ms sec ms F +0.5 +1 80 10 95 -3 -0.6 1 3.3 5.0 -0.5 -2 100 VDC VDC % V1 nom %VSBnom W ADC ADC mVpp 6 4.3 3 250 2 Max mV mV ADC ADC %VSBnom s sec Unit +0.5 +2 16.5 5 3.3 67 44 5.25 3.45 -3 Min Nom Unit VDC % V1 nom % V1 nom W ADC mVpp 1080 90.0 Vi =Vi min...Vi max Deviation from I1 tot / N, I1 > 10% I1 = 50% I1 nom, I1 = 5 ... 100% I1 nom, dI1/dt = 1 A/s, recovery within 1% of V1 nom Nom www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output tVSB rise CLoad Rise time Capacitive loading VSB = 10...90% VSB nom Tamb = 25 C 4 10 10000 ms F 4 SIGNALING AND CONTROL 4.1 FRONT LEDS Table 1: LED Status Operating Condition IN LED (INPUT OK) DC Line within range DC Line UV condition OUT LED 1) (OUTPUT OK) PSON High Hot-Standby Mode V1 or VSB out of regulation Over temperature shutdown Output over voltage shutdown (V1 or VSB) Output over current shutdown (V1 or VSB) Fan error (>15%) Over temperature warning Minor fan regulation error (>5%, <15%) 1) Further there is a button to disable the internal fan for approximately 5 seconds (not implemented yet). This allows the user to take input power measurements without fan consumptions to check efficiency compliance to the Climate Saver Computing Platinum specification. LED Signaling Solid Green Off Blinking Yellow (1:1) Blinking Yellow/Green (1:2) Solid Yellow Blinking Yellow/Green (2:1) Blinking Yellow/Green (1:1) The order of the criteria in the table corresponds to the testing precedence in the controller. The front-end has 2 front LEDs showing the status of the supply. LED number one is green and indicates DC power is on or off, while LED number two is bi-colored: green and yellow, and indicates DC power presence or fault situations. For the position of the LEDs see Figure 5. 4.2 GRAPHICAL USER INTERFACE Power-One provides with its "Power-One I2C Utility" a Windows(R) XP/Vista/Win7 compatible graphical user interface allowing the programming and monitoring of the PFE1100-12-054ND Front-End. The utility can be downloaded on www.power-one.com and supports both the PSMI and PMBusTM protocols. The GUI allows automatic discovery of the units connected to the communication bus and will show them in the navigation tree. In the monitoring view the power supply can be controlled and monitored. If the GUI is used in conjunction with the PFE1100-12054ND Evaluation Kit it is also possible to control the PSON pin(s) of the power supply. BCD.00034 Rev. AC, 10-July-2012 Figure 1: I2C Bus to uC (Graphical User Interface) The monitoring screen also allows to enable the hot-standby mode on the power supply. The mode status is monitored and by changing the load current it can be monitored when the power supply is being disabled for further energy savings. This obviously requires 2 power supplies being operated as a redundant system (like the evaluation kit). Note: The user of the GUI needs to ensure that only one of the power supplies have the hot-standby mode enabled. Page 4 / 9 www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output 5 ELECTROMAGNETIC COMPATIBILITY 5.1 IMMUNITY Note: Most of the immunity requirements are derived from EN 55024:1998/A2:2003. Test ESD Contact Discharge ESD Air Discharge Radiated Electromagnetic Field Burst Surge RF Conducted Immunity Standard / Description IEC / EN 61000-4-2, 8 kV, 25+25 discharges per test point (metallic case, LEDs, connector body) IEC / EN 61000-4-2, 15 kV, 25+25 discharges per test point (non-metallic user accessible surfaces) IEC / EN 61000-4-3, 10 V/m, 1 kHz/80% Amplitude Modulation, 1 s Pulse Modulation, 10 kHz...2 GHz IEC / EN 61000-4-4, level 3 Input DC port 1 kV, 1 minute DC port 0.5 kV, 1 minute IEC / EN 61000-4-5 Line to earth: 0.5 kV Line to line: 0.5 kV IEC/EN 61000-4-6, Level 3, 10 Vrms, CW, 0.1 ... 80 MHz Criteria B B A B B A 5.2 EMISSION Test Conducted Emission Radiated Emission Acoustical Noise BCD.00034 Rev. AC, 10-July-2012 Standard / Description EN55022 / CISPR 22: 0.15 ... 30 MHz, QP and AVG, single unit, Vi = 53 VDC, Px nom EN55022 / CISPR 22: 0.15 ... 30 MHz, QP and AVG, 2 units in rack system, Vi = 53 VDC, Px nom EN55022 / CISPR 22: 30 MHz ... 1 GHz, QP, single unit, Vi = 53 VDC, Px nom EN55022 / CISPR 22: 30 MHz ... 1 GHz, QP, 2 units in rack system, Vi = 53 VDC, Px nom Sound power statistical declaration (ISO 9296, ISO 7779, IS9295) @ 50% load Page 5 / 9 Criteria Class A 6 dB margin Class A 6 dB margin Class A 6 dB margin Class A 6 dB margin 62 dBA www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output 6 MECHANICAL 6.1 DIMENSIONS 13.4 321.5 0.4 25 2.4 34.6 1 98 0.6 14 Air Flow Direction Note: A 3D step file of the power supply casing is available on request. Figure 2: Side view 1 80 12.25 9.5 Note: Unlatching the supply is performed by pulling the green trigger in the handle. 8 40 4.4 0.6 8.75 Figure 3: Top view Figure 4: Side view 2 DC INPUT OK LED OUTPUT OK LED Figure 5: Front view BCD.00034 Rev. AC, 10-July-2012 Page 6 / 9 www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output 6.2 CONNECTIONS Input connector 1 Unit: Counter part: Pin Input 1 2 3 2 3 China Aviation (JOHNON OPTRONIC) P/N DP5ZJW0300-001 China Aviation (JOHNON OPTRONIC) P/N DP5TJY0300-001 (provided) Name Description Vin+ VinPE Input positive Input negative Ground Output connector Unit: Counter part: Pin Output 6, 7, 8, 9, 10 1, 2, 3, 4, 5 Control Pins A1 B1 C1 D1 E1 Tyco Electronics P/N 2-1926736-3 Tyco Electronics P/N 2-1926733-5 Note: Column 5 is lagging (short pins) Name Description V1 PGND +12 VDC main output Power ground (return) VSB VSB VSB VSB VSB BCD.00034 Rev. AC, 10-July-2012 Standby positive output (+3.3/5 V) Standby positive output (+3.3/5 V) Standby positive output (+3.3/5 V) Standby positive output (+3.3/5 V) Standby positive output (+3.3/5 V) Page 7 / 9 www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output A2 B2 C2 D2 E2 A3 B3 C3 D3 E3 A4 B4 C4 D4 E4 A5 B5 C5 D5 E5 SGND SGND HOTSTANDBYEN VSB_SENSE_R VSB_SENSE APS nc SDA V1_SENSE_R V1_SENSE SCL PSON SMB_ALERT nc INOK PSKILL ISHARE PWOK VSB_SEL PRESENT_L BCD.00034 Rev. AC, 10-July-2012 Signal ground (return) Signal ground (return) Hot standby enable signal Standby output negative sense Standby output positive sense I2C address and protocol selection (select by a pull down resistor) Reserved I2C data signal line Main output negative sense Main output positive sense I2C clock signal line Power supply on input (connect to A2/B2 to turn unit on) SMB Alert signal output Reserved DC input OK signal Power supply kill (lagging pin) Current share bus (lagging pin) Power OK signal output (lagging pin) Standby voltage selection (lagging pin) Power supply present (lagging pin) Page 8 / 9 www.power-one.com PFE1100-12-054ND Short Form Data Sheet 1100 Watts, 12 VDC Output 7 ACCESSORIES Item Description Ordering Part Number Source Power-One I2C Utility Windows XP/Vista/7 compatible GUI to program, control and monitor PFE Front-Ends (and other I2C units) N/A USB to I2C Converter Master I2C device to program, control and monitor I2C units in conjunction with the Power-One I2C Utility ZM-00056 Power-One Dual Connector Board Connector board to operate 2 PFE units in parallel. Includes an on-board USB to I2C converter (use Power-One I2C Utility as desktop software). SNP-OP-BOARD-01 Power-One www.power-one.com Copyright (c) 2010 Power-One Inc. All rights reserved. Words and logos that are identified as trademarks and/or service marks are, unless noted otherwise, the trademarks and service marks of Power-One Inc. in the U.S. and other countries. All other product or service names are the property of their respective holders. Power-One products are protected under numerous U.S. and foreign patents and pending applications, maskwork rights, and copyrights. Power-One reserves the right to make changes to any products and services at any time without notice. Power-One assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Power-One Inc. 1. NUCLEAR AND MEDICAL APPLICATIONS - Power-One products are not designed, intended for use in, or authorized for use as critical components in life support systems, equipment used in hazardous environments, or nuclear control systems without the express written consent of the respective divisional president of Power-One, Inc. 2. TECHNICAL REVISIONS - The appearance of products, including safety agency certifications pictured on labels, may change depending on the date manufactured. Specifications are subject to change without notice. BCD.00034 Rev. AC, 10-July-2012 Page 9 / 9 www.power-one.com