REVISIONS
LTR DESCRIPTION DATE (YR-MO-DA) APPROVED
A
Drawing updated to reflect current requirements. - ro
02-09-19 R. MONNIN
B
Drawing updated as part of 5 year review. -rrp
07-08-13
ROBERT M. HEBER
THE ORIGINAL FIRST PAGE OF THIS DRAWING HAS BEEN REPLACED.
REV
SHEET
REV
SHEET
REV STATUS REV B B B B B B B B B B B
OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11
PMIC N/A PREPARED BY
RICK C. OFFICER
DEFENSE SUPPLY CENTER COLUMBUS
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
CHARLES E. BESORE
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
MICHAEL A. FRYE
MICROCIRCUIT, LINEAR, OPERATIONAL
AMPLIFIER, WIDEBAND, HIGH SLEW RATE,
MONOLITHIC SILICON
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
DRAWING APPROVAL DATE
91-11-22
AMSC N/A
REVISION LEVEL
B SIZE
A CAGE CODE
67268
5962-87787
SHEET
1 OF
11
DSCC FORM 2233
APR 97 5962-E532-07
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 2
DSCC FORM 2234
APR 97
1. SCOPE
1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in
accordance with MIL-PRF-38535, appendix A.
1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example:
5962-87787 01 C X
Drawing number Device type
(see 1.2.1) Case outline
(see 1.2.2) Lead finish
(see 1.2.3)
1.2.1 Device type(s). The device type(s) identify the circuit function as follows:
Device type Generic number Circuit function
01 HA-2539 High slew rate wideband operational amplifier
02 EL-2039 High slew rate wideband operational amplifier
1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter Descriptive designator Terminals Package style
C GDIP1-T14 or CDIP2-T14 14 Dual-in-line
2 CQCC1-N20 20 Square leadless chip carrier
1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A.
1.3 Absolute maximum ratings.
Voltage between +VS and –VS terminals ................................ 35 V dc
Differential input voltage (VID) ................................................ 6.0 V dc
Voltage at either input terminal ............................................... +VS to –VS
Peak output current ( < 10 % duty cycle) ................................ 50 mA
Power dissipation (PD):
Case C ................................................................................ 1.03 W 1/
Case 2 ................................................................................. 1.06 W 2/
Storage temperature range ..................................................... -65°C to +150°C
Lead temperature (soldering, 10 seconds) ............................. +275°C
Junction temperature (TJ) ....................................................... +175°C
Thermal resistance, junction-to-case (θJC) ............................. See MIL-STD-1835
Thermal resistance, junction-to-ambient (θJA):
Case C ................................................................................ 98°C/W
Case 2 ................................................................................. 95°C/W
____
1/ Derate linearly above TA = +75°C at 10.2 mW/°C.
2/ Derate linearly above TA = +75°C at 10.6 mW/°C.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 3
DSCC FORM 2234
APR 97
1.4 Recommended operating conditions.
Positive supply voltage range (+VS) ....................................... +12 V dc to +15 V dc
Negative supply voltage range (-VS) ....................................... -12 V dc to -15 V dc
Common mode input voltage (VCM) ....................................... ≤ |(+ VS – (-VS)) / 2|
Load resistance (RL) ............................................................... 1.0 kΩ
Ambient operating temperature range (TA) ............................. -55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or
from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements shall be in accordance with MIL-PRF-38535, appendix A for non-
JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer
Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional certification to MIL-
PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying
activity approval in accordance with MIL-PRF -38535. This QML flow as documented in the Quality Management (QM) plan
may make modifications to the requirements herein. These modifications shall not affect form, fit, or function of the device.
These modifications shall not affect the PIN as described herein. A "Q" or "QML" certification mark in accordance with MIL-
PRF-38535 is required to identify when the QML flow option is used.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535, appendix A and herein.
3.2.1 Case outline. The case outline shall be in accordance with 1.2.2 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full ambient operating temperature range.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 4
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Input offset voltage
VIO V
CM = 0 V 1 01 -10 +10 mV
2,3 -15 +15
1 02 -2 +2
2,3 -6 +6
Input bias current
+IIB V
CM = 0 V 1 All -20 +20
μA
2,3 -25 +25
-IIB 1 -20 +20
2,3 -25 +25
Input offset current
IIO V
CM = 0 V 1 All -6 +6
μA
2,3 -8 +8
Common mode input
range +VCM +VS = +5 V, -VS = -25 V 1,2,3 All 10 V
-VCM +VS = +25 V, -VS = -5 V -10
Large signal voltage
gain +AVOL V
OUT = 0 V and +10 V, 1 All 10 kV/V
RL = 1 kΩ 2,3 5
-AVOL V
OUT = 0 V and -10 V, 1 10
RL = 1 kΩ 2,3 5
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 5
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Common mode
rejection ratio +CMRR ΔVCM = +10 V,
+VS = +5 V, -VS = -25 V,
VOUT = -10 V
1,2,3 All 60 dB
-CMRR ΔVCM = -10 V,
+VS = +25 V, -VS = -5 V,
VOUT = +10 V
60
Output current
+IOUT V
OUT = -10 V, TA = +25°C 1 All 10 mA
-IOUT V
OUT = +10 V,
TA = +25°C
-10
Output voltage swing
+VOUT R
L = 1 kΩ 1,2,3 All +10 V
-VOUT -10
Quiescent power
supply current +ICC I
OUT = 0 mA, 1,2,3 01 25 mA
VOUT = 0 V 02 17
-ICC 01 -25
02 -17
Power supply
rejection ratio +PSRR +VS = +5.0 V and +15 V,
-VS = -15 V
1,2,3 All 60 dB
-PSRR -VS = -5.0 V and -15 V,
+VS = +15 V
60
Quiescent power 2/ 3/
consumption PC V
OUT = 0 V, IOUT = 0 mA 1,2,3 01 720 mW
02 510
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Gain bandwidth 2/
product GBWP VOUT = 100 mV, 4 01 370 MHz
fO = 1 MHz, TA = +25°C 02 550
VOUT = 100 mV, 01 400
fO = 60 MHz, TA = +25°C 02 600
Output resistance 2/
ROUT T
A = +25°C 4 All 60
Ω
Full power 2/ 4/
bandwidth FPBW VPEAK = 10 V,
TA = +25°C
4 All 8.4 MHz
Closed loop stable 2/
gain CLSG RL = 1 kΩ, CL ≤ 10 pF 4,5,6 All 10 V/V
Slew rate 2/
+SR VOUT = -5.0 V to +5.0 V,
RL = 1 kΩ, AV = 10 V/V,
7 01 530
V/μs
measured at –4.0 V to
+4.0 V 8 425
VOUT = -5.0 V to +5.0 V,
RL = 1 kΩ, AV = 10 V/V,
7 02 530
measured at –2.5 V to
+2.5 V 8 425
-SR VOUT = +5.0 V to -5.0 V,
RL = 1 kΩ, AV = 10 V/V,
7 01 530
measured at –4.0 V to
+4.0 V 8 425
VOUT = +5.0 V to -5.0 V,
RL = 1 kΩ, AV = 10 V/V,
7 02 530
measured at –2.5 V to
+2.5 V 8 425
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 7
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions 1/
-55°C ≤ TA ≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits Unit
Min Max
Rise time 2/ 5/
tR V
OUT = 0 V to +200 mV,
TA = +25°C
9 All 10 ns
Fall time 2/ 5/
tF V
OUT = 0 V to -200 mV,
TA = +25°C
9 All 10 ns
Overshoot 2/
+OS VOUT = 0 V to +200 mV,
TA = +25°C
9 All 50 %
-OS VOUT = 0 V to -200 mV,
TA = +25°C
50
1/ For all tests, unless otherwise specified, +VS = +15 V, -VS = -15 V, and CL ≤ 10 pF. Unless otherwise specified,
for dc tests, RS = 100 Ω, RL = 100 kΩ, VOUT = 0 V, and for ac tests, AV = +10 V/V.
2/ If not tested, shall be guaranteed to the limits specified in table I herein.
3/ Quiescent power consumption based on quiescent supply current test maximum (no load on outputs).
4/ Full power bandwidth = SR / ( 2 x π x VPEAK ).
5/ Rise and fall times measured between 10 percent and 90 percent point.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 8
DSCC FORM 2234
APR 97
Device types
01 and 02
Case outlines
C 2
Terminal
number T erminal symbol
1
+INPUT NC
2
NC +INPUT
3
-VS NC
4
NC -VS
5
NC NC
6
NC NC
7
NC NC
8
OUTPUT NC
9
NC NC
10
+VS NC
11
NC NC
12
NC OUTPUT
13
NC NC
14
-INPUT +VS
15
--- NC
16
--- NC
17
--- NC
18
--- NC
19
--- NC
20
--- -INPUT
NC = No connection
FIGURE 1. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 9
DSCC FORM 2234
APR 97
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are described in table I.
3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed
in 1.2 herein. In addition, the manufacturer's PIN may also be marked. For packages where marking of the entire SMD PIN
number is not feasible due to space limitations, the manufacturer has the option of not marking the "5962-" on the device.
3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance
to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a "Q" or "QML" certification mark in
accordance with MIL-PRF-38535 to identify when the QML flow option is used.
3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an
approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of compliance submitted to DSCC-VA prior to
listing as an approved source of supply shall affirm that the manufacturer's product meets the requirements of MIL-PRF-38535,
appendix A and the requirements herein.
3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appendix A shall be provided
with each lot of microcircuits delivered to this drawing.
3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing.
3.9 Verification and review. DSCC, DSCC's agent, and the acquiring activity retain the option to review the manufacturer's
facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the
reviewer.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535,
appendix A.
4.2 Screening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices
prior to quality conformance inspection. The following additional criteria shall apply:
a. Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method
1015 of MIL-STD-883.
(2) TA = +125°C, minimum.
b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Quality conformance inspection. Quality conformance inspection shall be in accordance with method 5005 of MIL-STD-
883 including groups A, B, C, and D inspections. The following additional criteria shall apply.
4.3.1 Group A inspection.
a. Tests shall be as specified in table II herein.
b. Subgroups 10 and 11 in table I, method 5005 of MIL-STD-883 shall be omitted.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 10
DSCC FORM 2234
APR 97
TABLE II. Electrical test requirements.
MIL-STD-883 test requirements Subgroups
(in accordance with
MIL-STD-883, method 5005,
table I)
Interim electrical parameters
(method 5004) ----
Final electrical test parameters
(method 5004) 1*,2,3,4,5,6
Group A test requirements
(method 5005) 1,2,3,4,5,6,7**,8**,9
Groups C and D end-point
electrical parameters
(method 5005)
1
* PDA applies to subgroup 1.
** Subgroups 7 and 8 shall be guaranteed, if not tested, to the
limits specified in table I.
4.3.2 Groups C and D inspections.
a. End-point electrical parameters shall be as specified in table II herein.
b. Steady-state life test conditions, method 1005 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision
level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2) TA = +125°C, minimum.
(3) Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535, appendix A.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-87787
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990 REVISION LEVEL
B SHEET 11
DSCC FORM 2234
APR 97
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor-
prepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for
the individual documents. This coordination will be accomplished using DD Form 1692, Engineering Change Proposal.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system
application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be
used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronics devices (FSC
5962) should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone
(614) 692-0547
6.6 Approved sources of supply. Approved sources of supply are listed in MIL-HDBK-103. The vendors listed in MIL-
HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to and accepted by
DSCC-VA.
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 07-08-13
Approved sources of supply for SMD 5962-87787 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised
to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate
of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded by the next
dated revision of MIL-HDBK-103 and QML-38535. DSCC maintains an online database of all current sources of
supply at http://www.dscc.dla.mil/Programs/Smcr/ .
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-8778701CA
34371 HA1-2539/883
3/ EHA1-2539/883B
5962-87787012A
3/ HA4-2539/883
3/ EHA4-2539/883B
5962-8778702CA
3/ EL2039J/883B
5962-87787022A
3/ EL2039L/883B
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
3
/ Not available from an approved source of supply.
Vendor CAGE Vendor name
number and address
34371 Intersil Corporation
1001 Murphy Ranch Road
Milpitas, CA 95035-6803
Point of contact: 1650 Robert J. Conlan Blvd
Palm Bay, FL 32905
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
