RClamp1654P RailClamp(R) Low Capacitance TVS Array PROTECTION PRODUCTS - RailClamp(R) Description Features Transient protection for high-speed data lines to RailClamp(R) is a low capacitance TVS array designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected to data and transmission lines from overvoltage caused by ESD (electrostatic discharge), CDE (Cable Discharge Events), and EFT (electrical fast transients). The RClamp1654P is specifically designed to protect portable devices that utilize the USB port for battery charging. The unique design of this device features low capacitance TVS diodes for protection of the USB data (DP, DM) and USB ID (accessory detect) pins operating up to 5 volts. Loading capacitance on these lines is <1pF for maximum signal integrity. An integrated 12 volt TVS diode is used for protection of the USB voltage bus. This ensures the device will remain in a high-impedance state during normal USB operation or when the battery is being charged. Leakage current of the VBus protection is <50nA when operating at 12 volts. The RClamp1654P is in a 6-pin, RoHS compliant, SLP1616P6 package. It measures 1.6 x 1.6 x 0.60mm. The leads are spaced at a pitch of 0.5mm and are finished with lead-free NiPdAu. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (15kV air, 8kV contact discharge). IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Array of surge rated diodes with internal TVS Diode Small package (1.6 x 1.6mm) saves board space Protects USB DP, DM, and ID Pin operating up to 5.5V Protects USB VBus operating up to 12V Low capacitance (<1pF) on DP, DM, and ID Pins Minimal insertion loss to 2.0GHz Low leakage current Low clamping voltage Large ground pad for increased ESD performance Solid-state silicon-avalanche technology Mechanical Characteristics Applications USB 2.0 USB OTG Circuit Diagram PIN Configuration 6 1 2 SLP1616P6 6L package RoHS/WEEE Compliant Nominal Dimensions: 1.6 x 1.6 x 0.60 mm Lead Finish: NiPdAu Molding compound flammability rating: UL 94V-0 Marking : Marking code + two character date code Packaging : Tape and Reel DM 1 3 5.5V DP 2 USB ID 3 12V Gnd 6 VBus 5 NC 4 NC GND SLP1616P6 (Top View) Revision 11/07/2008 1 www.semtech.com RClamp1654P PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 8/20s) Pp k 100 Watts Peak Pulse Current (tp = 8/20s) IP P 3 A ESD per IEC 61000-4-2 (Air) ESD per IEC 61000-4-2 (Contact) VESD 15 8 kV TJ -55 to +125 C TSTG -55 to +150 C Peak Pulse Power (tp = 8/20s) Pp k 200 Watts Peak Pulse Current (tp = 8/20s) IP P 5 A ESD per IEC 61000-4-2 (Air) ESD per IEC 61000-4-2 (Contact) VESD 15 8 kV TJ -55 to +125 C TSTG -55 to +150 C D P, D M , U S B I D ( P i n s 1 , 2 , 3 ) Operating Temperature Storage Temperature V B u s ( P i n 6) Operating Temperature Storage Temperature (c) 2008 Semtech Corp. 2 www.semtech.com RClamp1654P PROTECTION PRODUCTS Electrical Characteristics (T = 25oC) D M , D P, U S B I D T V S ( P i n s 1 , 2 , 3 ) Parameter Symbol Conditions Reverse Stand-Off Voltage VRWM Pin 1, 2, or 3 to GN D Reverse Breakdown Voltage V BR It = 1mA, Pin 1, 2, or 3 to GN D Reverse Leakage Current IR VRWM = 5.5V, Pin 1, 2, or 3 to GN D Forward Voltage VF If = 15mA GN D to Pin 1, 2, or 3 Clamping Voltage VC Clamping Voltage Junction Capacitance Maximum Units 5.5 V 8 10 V 0.100 1 A 1.2 V IPP = 1A, tp = 8/20s Pin 1, 2, or 3 to GN D 15 V VC IPP = 3A, tp = 8/20s Pin 1, 2, or 3 to GN D 30 V Cj VR = 0V, f = 1MHz, Pin 1, 2, or 3 to GN D 0.8 pF 0.5 pF VR = 0V, f = 1MHz, Between I/O pins (c) 2008 Semtech Corp. 3 Minimum 6.5 Typical 0.6 0.7 www.semtech.com RClamp1654P PROTECTION PRODUCTS Electrical Characteristics (T = 25oC) V B u s T V S ( P i n 6) Parameter Symbol Conditions Reverse Stand-Off Voltage VRWM Pin 6 to GN D Reverse Breakdown Voltage V BR It = 1mA, Pin 6 to GN D Reverse Leakage Current IR VRWM = 12V Pin 6 to GN D Forward Voltage VF If = 10mA GN D to Pin 6 Clamping Voltage VC Reverse Clamping Voltage Junction Capacitance (c) 2008 Semtech Corp. Maximum Units 12 V 16.5 18 V 0.005 0.05 A 1.0 V IPP = 1A, tp = 8/20s Pin 6 to Ground 20 V VFC IPP = 10A, tp = 8/20s Ground to Pin 6 3 V Cj VR = 0V, f = 1MHz Pin 6 to GN D 100 pF 4 Minimum 15 0.6 Typical www.semtech.com RClamp1654P PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 10 110 % of Rated Power or PI P Peak Pulse Power - PPP (kW) 100 1 0.1 90 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 100 0 1000 25 50 110 Waveform Parameters: tr = 8s td = 20s 100 90 50 td = IPP/2 30 20 10 0 0 5 10 15 150 35 e-t 40 125 40 Clamping Voltage - VC (V) Percent of I PP 80 60 100 Clamping Voltage vs. Peak Pulse Current (Pin 1, 2, or 3 to GND) Pulse Waveform 70 75 Ambient Temperature - TA (oC) Pulse Duration - tp (us) 20 25 30 25 20 15 Waveform Parameters: tr = 8s td = 20s 10 5 30 0 Time (s) 0 0.5 1 1.5 2 2.5 3 3.5 4 Peak Pulse Current - IPP (A) Clamping Voltage vs. Peak Pulse Current (Pin 6 to GND) Reverse Clamping Voltage vs. Peak Pulse Current (Pin GND to Pin 6) 5 30 Waveform Parameters: tr = 8s td = 20s Clamping Voltage - VC (V) Clamping Voltage - VC (V) 4.5 25 20 15 10 Waveform Parameters: tr = 8s td = 20s 5 1 (c) 2008 Semtech Corp. 2 3 4 Peak Pulse Current - IPP (A) 5 3.5 3 2.5 2 1.5 1 0.5 0 0 4 0 6 0 2 4 6 8 10 Peak Pulse Current - IPP (A) 5 www.semtech.com RClamp1654P PROTECTION PRODUCTS Typical Characteristics CJ(VR) / CJ(VR=0) Normalized Capacitance vs. Reverse Voltage (Pin 1, 2, or 3 to Gnd) Insertion Loss S21 (Pin 1, 2, or 3 to Gnd) CH1 S21 1.5 1.4 1.3 1.2 1.1 1 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 LOG 6 dB / REF 0 dB 1: -0.086 dB 900 MHz 3 0 dB 1 2: -0.0336 dB 1.8 GHz 2 3: -0.126 dB 2.5 GHz -6 dB -12 dB -18 dB -24 dB -30 dB -36 dB f = 1 MHz 0 1 2 3 Reverse Voltage - VR (V) 4 -42 dB 5 -48 dB 1 MHz START . 030 MHz 10 MHz 100 MHz 3 1 GHz GHz STOP 3 000. 000000 MHz Analog Crosstalk CH1 S21 LOG START . 030 MHz (c) 2008 Semtech Corp. 20 dB/REF 0 dB STOP 3000. 000000 MHz 6 www.semtech.com RClamp1654P PROTECTION PRODUCTS Applications Information Figure 1- Pin Configuration & Circuit Diagram Device Connection Options for Protecting One USB Port USB Data and ID lines are connected at pins 1, 2, and 3. These inputs are referenced to an internal 5 volt TVS protection device. When the voltage on these lines exceed 5 volts, the TVS will conduct. Pin 6 is connected to the USB voltage bus (VBus). This device will conduct when the voltage on the bus exceeds 12 volts. The center tab is connected to ground. The path length should also be kept as short as possible to minimize parasitic inductance. For best results, multiple micro-vias are recommended to the ground plane. 6 1 2 3 5.5V 12V GND Protecting USB Interfaces VBus DM DP USB ID GND 5 The RClamp1654P is optimized for use on systems that utilize the USB interface for battery charging. Low capacitance protection is provided for the USB data (DM, DP) and USB ID pins. The maximum capacitance on these lines is <1pF for maximum signal integrity. All three lines are referenced to an internal 5 volt TVS device. A separate 12 volt TVS device is used for protection of the USB voltage bus. This allows battery charging without signal clipping. A typical example is shown in Figure 2. 4 3 2 1 1 Mini USB Gnd Figure 2 - USB Protection (c) 2008 Semtech Corp. 7 www.semtech.com RClamp1654P PROTECTION PRODUCTS Applications Information - Spice Model VBus D2 D4 D3 I/O D1 RClamp1654P Spice Model R Clamp1654P Spice Parameters (c) 2008 Semtech Corp. Parameter Unit D1 D2 D3 D4 IS Amp 1E-20 1E-20 2E-12 1.48E-14 BV Volt 100 100 9.36 16.2 VJ Volt 0.7 0.7 0.6 0.7 RS Ohm 0.458 1.0 2.6 0.927 IB V Amp 1E-3 1E-3 1E-3 1E-3 CJO Farad 0.3E-12 0.3E-12 56E-12 49E-12 TT sec 2.541E-9 2.541E-9 2.541E-9 2.541E-9 M -- 0.01 0.01 0.23 0.272 N -- 1.1 1.1 1.1 1.1 EG eV 1.11 1.11 1.11 1.11 8 www.semtech.com RClamp1654P PROTECTION PRODUCTS Outline Drawing - SLP1616P6 A D PIN 1 INDICATOR (LASER MARK) B E DIM A SEATING PLANE aaa C A2 A A1 A2 b D D1 E E1 e L N aaa bbb C A1 D1 1 2 LxN E/2 E1 DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .020 .023 .026 0.00 .001 .002 (.005) .008 .010 .012 .059 .063 .067 .041 .047 .051 .059 .063 .067 .010 .016 .020 .020 BSC .010 .013 .016 6 .003 .004 0.50 0.58 0.65 0.00 0.03 0.05 (0.13) 0.20 0.25 0.30 1.50 1.60 1.70 1.05 1.20 1.30 1.50 1.60 1.70 0.25 0.40 0.50 0.50 BSC 0.25 0.33 0.40 6 0.08 0.10 N bxN bbb e C A B D/2 NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. COPLANARITY APPLIES TO THE EXPOSED PAD AS WELL AS THE TERMINALS. Land Pattern - SLP1616P6 P X DIMENSIONS Z H G DIM C G H K P X Y Z (C) Y INCHES .060 .035 .018 .051 .020 .012 .025 .085 MILLIMETERS 1.52 0.89 0.45 1.30 0.50 0.30 0.63 2.15 K NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 3. THERMAL VIAS IN THE LAND PATTERN OF THE EXPOSED PAD SHALL BE CONNECTED TO A SYSTEM GROUND PLANE. FAILURE TO DO SO MAY COMPROMISE THE THERMAL AND/OR FUNCTIONAL PERFORMANCE OF THE DEVICE. (c) 2008 Semtech Corp. 9 www.semtech.com RClamp1654P PROTECTION PRODUCTS Marking Ordering Information 1654P YW Part Number Lead Finish Qty per Reel R eel Size RClamp 1654P.TCT Pb Free 3,000 7 Inch RailClamp and RClamp are marks of Semtech Corporation YW = Two character Date Code Tape and Reel Specification Device Orientation in Tape Pin 1 in upper left towards sprocket holes A0 1.78 +/-0.05 mm Tape Width 8 mm B0 K0 1.78 +/-0.05 mm B, (Max) D 4.2 mm 1.5 + 0.1 mm - 0.0 mm ) 0.69 +/-0.05 mm D1 E 0.5 mm 0.05 1.750.10 mm F 3.50.05 mm K (MAX) P P0 P2 2.4 mm 4.00.1 mm 4.00.1 mm 2.00.05 mm T(MAX) 0.4 mm W 8.0 mm + 0.3 mm - 0.1 mm Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 (c) 2008 Semtech Corp. 10 www.semtech.com