Ordering number : ENA2162 LC717A10AJ CMOS LSI Capacitance-Digital-Converter LSI for Electrostatic Capacitive Touch Sensors http://onsemi.com Overview The LC717A10AJ is a high-performance and low-cost capacitance-digital-converter LSI for electrostatic capacitive touch sensor, especially focused on usability. It has 16 channels capacitance-sensor input. This makes it ideal for use in the products that need many switches. Since the calibration function and the judgment of ON/OFF are automatically performed in LSI internal, it can make development time more short. A detection result (ON/OFF) for each input can be read out by the serial interface (I2C compatible bus or SPI). Also, measurement value of each input can be read out as 8-bit digital data. Moreover, gain and other parameters can be adjusted using serial interface. Features * Detection system: Differential capacitance detection (Mutual capacitance type) * Input capacitance resolution: Can detect capacitance changes in the femto Farad order * Measurement interval (16 differential inputs): 30ms (Typ) (at initial configuration), 6ms (Typ) (at minimum interval configuration) * External components for measurement: Not required * Interface: I2C * compatible bus or SPI selectable. * Current consumption: 570A (Typ) (VDD = 2.8V), 1.3mA (Typ) (VDD = 5.5V) * Supply voltage: 2.6V to 5.5V * Detection operations: Switch * Packages: SSOP30 * I2C Bus is a trademark of Philips Corporation. Semiconductor Components Industries, LLC, 2013 August, 2013 Ver1.0.1 D1912HKPC 20121204-S00003 No.A2162-1/11 LC717A10AJ Specifications Absolute Maximum Ratings at Ta = +25C Parameter Symbol Supply voltage VDD Input voltage Ratings (VSS = 0V) Unit -0.3 to +6.5 V VIN -0.3 to VDD+0.3 V Output voltage VOUT -0.3 to VDD+0.3 V Power dissipation Pd max Storage temperature Tstg 160 mW Remarks *1 *2 Ta = +105C, Mounted on a substrate *3 C -55 to +125 *1) Apply to Cin0 to 15, Cref, CrefAdd, nRST, SCL, SDA, SA0, SA1, SCK, SI, nCS *2) Apply to Cdrv, SDA, SO, INTOUT *3) Single-layer glass epoxy board (76.1x114.3x1.6t mm) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. Recommended Operating Conditions Parameter Operating supply voltage Symbol Conditions VDD Supply ripple + noise Vpp Operating temperature Topr min typ max 2.6 -40 25 Unit 5.5 V 20 mV 105 C Remarks *1 *1) We recommend connecting large and small capacitance between VDD and VSS. In this case, the small capacitance is equal to or more than 0.1F, and layout nearby LSI. Electrical Characteristics at VSS = 0V, VDD = 2.6 to 5.5V, Ta = -40 to +105C * Unless otherwise specified, the Cdrv drive frequency is fCDRV = 143kHz. * Not tested at low temperature before shipment. Parameter Symbol Capacitance detection resolution N Output noise RMS NRMS Input offset capacitance CoffRANGE Conditions min typ minimum gain setting 1.0 CoffRESO adjustment resolution Cin offset drift CinDRIFT CinSENSE minimum gain setting Cin pin leak current ICin Cin = Hi-Z Cin allowable parasitic input CinSUB Cin against VSS *1 *3 8.0 pF *1 *3 8 bit 8 0.04 fCDRV ICDRV nRST minimum pulse width tNRST Power-on reset time tPOR Power-on reset operation tPOROP 100 Cdrv = Hi-Z Power-on reset operation nA 30 pF 143 186 kHz 25 500 nA 10 VPOROP Power-on reset operation tVDD 0.1 0V to VDD 1 *2 LSB/fF 20 condition: Input voltage *1 0.12 1 condition: Hold time LSB 500 25 capacitance Cdrv pin leak current Remarks bit LSB minimum gain setting Cin detection sensitivity Cdrv drive frequency Unit 8 adjustment range Input offset capacitance max *1 *3 s *1 ms *1 ms *1 V *1 V/ms *1 condition: Power supply rise rate Continued to the next page. No.A2162-2/11 LC717A10AJ Continued from the previous page. Parameter Pin input voltage Pin output voltage Symbol Conditions VIH High input VIL Low input VOH High output (IOH = +3mA) VOL min typ 0.2VDD VOL I2C Low output ILEAK Current consumption IDD Remarks V *1 *4 V *5 0.2VDD SDA Low output 0.4 V 1 A *6 570 700 A *1 *3 1.3 1.6 mA *1 *3 1 A *3 (IOL = -3mA) Pin leak current Unit 0.8VDD (IOL = -3mA) SDA pin output voltage max 0.8VDD When initial setting and non-touch VDD = 2.8V When initial setting and non-touch ISTBY VDD = 5.5V During Sleep process *1) Design guarantee values (not tested before shipment) *2) Measurements conducted using the test mode in the LSI *3) Ta = +25C *4) Apply to nRST, SCL, SDA, SA0, SA1, SCK, SI, nCS *5) Apply to Cdrv, SO, INTOUT *6) Apply to nRST, SCL, SDA, SA0, SA1, SCK, SI, nCS No.A2162-3/11 LC717A10AJ I2C Compatible Bus Timing Characteristics at VSS = 0, VDD = 2.6 to 5.5V, Ta = -40 to +105C *Not tested at low temperature before shipment Parameter Symbol Pin Name SCL clock frequency fSCL SCL START condition hold time tHD;STA SCL Conditions min typ max Unit 400 SDA kHz 0.6 s SCL clock low period tLOW SCL 1.3 s SCL clock high period tHIGH SCL 0.6 s Repeated START condition tSU;STA SCL 0.6 s setup time SDA Data hold time tHD;DAT SCL 0 SDA Data setup time tSU;DAT SCL 100 SDA SDA, SCL rise/fall time tr / tf 0.9 SCL 300 SDA STOP condition setup time tSU;STO SCL SDA STOP-to-START bus release tBUF time SCL SDA Remarks *1 s s *1 s *1 0.6 s 1.3 s *1 Unit Remarks *1) Design guarantee values (not tested before shipment) SPI Bus Timing Characteristics at VSS = 0, VDD = 2.6 to 5.5V, Ta = -40 to +105C *Not tested at low temperature before shipment Parameter SCK clock frequency Symbol fSCK Pin Name Conditions min typ SCK max 5 MHz SCK clock Low time tLOW SCK 90 ns *1 SCK clock High time tHIGH SCK 90 ns *1 Input signal rise/fall time tr / tf ns *1 90 ns *1 90 ns *1 20 ns *1 30 ns *1 90 ns *1 90 ns *1 90 ns *1 80 ns *1 80 ns *1 0 ns *1 0 ns *1 nCS SCK 300 SI nCS setup time tSU;NCS nCS SCK SCK clock setup time tSU;SCK nCS SCK Data setup time tSU;SI SCK SI Data hold time tHD;SI SCK SI nCS hold time tHD;NCS nCS SCK SCK clock hold time tHD;SCK nCS SCK nCS standby pulse width tCPH nCS Output high impedance time tCHZ nCS from nCS Output data determination time SO tv SCK SO Output data hold time tHD;SO SCK SO Output low impedance time from SCK clock tCLZ SCK SO *1) Design guarantee values (not tested before shipment) No.A2162-4/11 LC717A10AJ Power-on Reset (POR) When power is turned on, power-on reset is enabled inside the LSI and its state is released after a certain power-on reset time, tPOR. Power-on Reset operation condition; Power supply rise rate tVDD must be at least 1V/ms. Since INTOUT pin changes from "High" to "Low" at the same time as the released of power-on reset, it is possible to verify the timing of release of power-on reset externally. During power-on reset, Cin, Cref and CrefAdd are unknown. VDD tVDD VPOROP tPOR tPOR tPOROP POR (LSI internal signal) RESET UNKNOWN RELEASE INTOUT VALID Cin, Cref, CrefAdd UNKNOWN RESET RELEASE UNKNOWN UNKNOWN VALID fig.1 I2C Compatible Bus Data Timing 90% SDA 10% 90% 10% tHD;DTA tLOW tSU;DTA 90% 90% 10% tSU;STA 90% SCL tHD;STA 10% tHIGH tr 10% tHD;STA 90% 10% 10% 90% 90% 90% tBUF 10% tSU;STO 90% 10% tf repeated START condition START condition STOP condition START condition fig.2 I2C Compatible Bus Communication Formats * Write format (data can be written into sequentially incremented addresses) START Slave Address Write=L ACK Register Address (N) Slave ACK Data written to Register Address (N) ACK Data written to Register Address (N+1) ACK STOP Slave Slave Slave fig.3 * Read format (data can be read from sequentially incremented addresses) START Slave Address Write=L ACK Slave RESTART Slave Address Register Address (N) ACK Slave Read=H ACK Data read from Register Address (N) ACK Data read from Register Address (N+1) ACK Data read from Register Address (N+2) NACK STOP Slave Master Master Master fig.4 No.A2162-5/11 LC717A10AJ I2C Compatible Bus Slave Address Selection of two kinds of addresses is possible through the SA0 and SA1 terminals. SA1 input SA0 input 7bit slave address Low Low 0x16 Low High 0x17 High Low 0x18 High High 0x19 Binary notation 8bit slave address 00101100b (Write) 0x2C 00101101b (Read) 0x2D 00101110b (Write) 0x2E 00101111b (Read) 0x2F 00110000b (Write) 0x30 00110001b (Read) 0x31 00110010b (Write) 0x32 00110011b (Read) 0x33 SPI Data Timing (SPI Mode 0 / Mode 3) tCPH nCS tSU;SCK tSU;NCS tHIGH tHD;NCS tf tr tLOW tHD;SCK SCK tSU;SI tHD;SI VALID SI tCLZ SO tHD;SO tCHZ VALID Hi-Z tV fig.5 SPI Communication Formats (Example of Mode 0) * Write format (data can be written into sequentially incremented addresses with preserving nCS = L) nCS SCK SI SO Write=L 7 6 5 4 3 2 1 0 7 6 5 4 3 2 1 0 Data written to Register Address(N) Register Address(N) 7 6 5 4 3 2 1 0 Data written to Register Address(N+1) Hi-Z fig.6 * Read format (data can be read from sequentially incremented addresses with preserving nCS = L) nCS SCK SI Read=H 7 6 5 4 3 2 1 0 Register Address(N) SO Hi-Z 7 6 5 4 3 2 1 0 Data read from Register Address(N) 7 6 5 4 3 2 1 0 7 Data read from Register Address(N+1) fig.7 No.A2162-6/11 LC717A10AJ Package Dimensions [LC717A10AJ] unit : mm (typ) 3421 8.0 0.5 6.4 4.4 30 12 0.22 0.5 0.15 0.1 (1.5) 1.7 MAX (0.5) SANYO : SSOP30(225mil) Pin Assignment Pin No. Pin Name Pin No. Pin Name 1 VDD 16 Cref 2 VSS 17 CrefAdd 3 Non Connect *1 18 Cdrv 4 Cin4 19 INTOUT 5 Cin5 20 SA1 6 Cin6 21 SCL/SCK 7 Cin7 22 SDA/SI 8 Cin8 23 SA0/SO 9 Cin9 24 nCS 10 Cin10 25 nRST 11 Cin11 26 Non Connect *1 12 Cin12 27 Cin0 13 Cin13 28 Cin1 14 Cin14 29 Cin2 15 Cin15 30 Cin3 *1) connect to GND when mounted No.A2162-7/11 LC717A10AJ Block Diagram Cin0 Cin1 Cin2 Cin3 VDD Cin4 VSS Cin5 Cin6 1st AMP Cin7 Cin8 2nd AMP A/D CONVERTER MUX Cin9 Cin10 Cin11 Cdrv CONTROL LOGIC Cin12 INTOUT Cin13 nRST Cin14 Cin15 nCS POR OSCILLATOR SCL/SCK 2 I C/SPI Cref CrefAdd MUX SDA/SI SA0/SO SA1 LC717A10AJ is capacitance-digital-converter LSI capable of detecting changes in capacitance in the order of femto Farads. It consists of an oscillation circuit that generates the system clock, a power-on reset circuit that resets the system when the power is turned on, a multiplexer that selects the input channels, a two-stage amplifier that detects the changes in the capacitance and outputs analog-amplitude values, a A/D converter that converts the analog-amplitude values into digital data, an I2C compatible bus or a SPI that enables serial communication with external devices and a control logic that controls the entire chip. No.A2162-8/11 LC717A10AJ Pin Functions Pin Name I/O Pin Functions Cin0 I/O Capacitance sensor input Cin1 I/O Capacitance sensor input Cin2 I/O Capacitance sensor input Cin3 I/O Capacitance sensor input Cin4 I/O Capacitance sensor input Cin5 I/O Capacitance sensor input Cin6 I/O Capacitance sensor input Cin7 I/O Capacitance sensor input Cin8 I/O Capacitance sensor input Cin9 I/O Capacitance sensor input Cin10 I/O Capacitance sensor input Cin11 I/O Capacitance sensor input Cin12 I/O Capacitance sensor input Cin13 I/O Capacitance sensor input Cin14 I/O Capacitance sensor input Cin15 I/O Capacitance sensor input Cref I/O Reference capacitance input CrefAdd I/O Reference capacitance input for addition Pin Type VDD AMP R VSS Buffer VDD Cdrv O Output for capacitance sensors drive Buffer INTOUT O Interrupt output VSS Clock input (I2C) SCL/SCK I nCS I nRST I External reset signal inverting input SA1 I Slave address selection (I2C) / Clock input (SPI) VDD Interface selection R / Chip select inverting input (SPI) VSS VDD R SDA/SI I/O Data input and output (I2C) / Data input (SPI) VSS Continued to the next page. No.A2162-9/11 LC717A10AJ Continued from the previous page. Pin Name I/O Pin Functions Pin Type VDD SA0/SO I/O R Slave address selection (I2C) / Data output (SPI) VSS VDD Power supply (2.6V to 5.5V) *1 VSS Ground (Earth) *1 *2 Buffer *1) Inserting a high-valued capacitor and a low-valued capacitor in parallel between VDD and VSS is recommended. In this case, the small-valued capacitor should be at least 0.1F, and is mounted near the LSI. *2) When VSS terminal is not grounded in battery-powered mobile equipment, detection sensitivity may be degraded. Details of Pin Functions Cin0 to Cin15 These are the capacitance-sensor-input pins. These pins are used by connecting them to the touch switch pattern. Cin and the Cdrv wire patterns should be close to each other. By doing so, Cdrv and Cin patterns are capacitively coupled. Therefore, LSI can detect capacitance change near each pattern as 8bit digital data. However, if the shape of each pattern or the capacitively coupled value of Cdrv is not appropriate, it may not be able to detect the capacitance change correctly. In this LSI, there is a two-stage amplifier that detects the changes in the capacitance and outputs analog-amplitude values. Cin0 to Cin15 are connected to the inverting input of the 1st amplifier. During measurement process, channels other than the one being measured are all in "Low" condition. Leave the unused terminals open. Cref, CrefAdd These are the reference-capacitance-input pins. These are used by connecting to the wire pattern like Cin pins or are used by connecting any capacitance between this pin and Cdrv pin. In this LSI, there is a two-stage amplifier that detects the changes in the capacitance and outputs analog-amplitude values. Cref is connected to the non-inverting input of the 1st amplifier. Due to the parasitic capacitance generated in the wire connections of Cin pins and their patterns, as well as the one generated between the wire patterns of Cin and Cdrv pins, Cref may not detect capacitance change of each Cin pin accurately. In this case, connect an appropriate capacitance between Cref and Cdrv to detect capacitance change accurately. However, if the difference between the parasitic capacitance of each Cin pin is extremely large, it may not detect capacitance change of each Cin pin correctly. CrefAdd can be used as additional terminal for Cref. Leave the CrefAdd open if not in used. Cdrv It is the output pin for capacitance sensors drive. It outputs the pulse voltage which is needed to detect capacitance at Cin0 to Cin15. Cdrv and Cin wire patterns should be close to each other so that they are capacitively coupled. INTOUT It is the interrupt-output pin. It is used by connecting to a main microcomputer if necessary, and use as interrupt signal. (High Active) Leave the terminal open if not in used. SCL/SCK Clock input (I2C) / Clock input (SPI) It is the clock input pin of the I2C compatible bus or the SPI depending on the mode of operation. No.A2162-10/11 LC717A10AJ nCS Interface selection / Chip-select-inverting input (SPI) Selection of I2C compatible bus mode or SPI mode is through this terminal. After initialization, the LSI is automatically in I2C compatible bus mode. To continually use I2C compatible bus mode, fix nCS pin to "High". To switch to SPI mode after LSI initialization, change the nCS input "High" "Low". The nCS pin is used as the chipselect-inverting input pin of SPI, and SPI mode is kept until LSI is again initialized. nRST It is the external-reset-signal-inverting-input pin. When nRST pin is "Low", LSI is in reset state. Each pin (Cin0 to 15, Cref, CrefAdd) is "Hi-Z" during reset state. SDA/SI Data input and output (I2C) / Data input (SPI) It is the data input and output pin of the I2C compatible bus or the data input pin of the SPI depending on the mode of operation. SA0/SO Slave address selection (I2C) / Data output (SPI) It is the slave address selection pin of the I2C compatible bus or the data output pin of the SPI depending on the mode of operation. SA1 Slave address selection (I2C) It is the slave address selection pin of the I2C compatible bus. When SPI mode, connect to the SA1 pin to GND. ON Semiconductor and the ON logo are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC's product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent-Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PS No.A2162-11/11 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: ON Semiconductor: LC717A10AJ-AH LC717A10AR-NH