DF11 Power entry modules without line filter www.schurter.com/pg05 IEC Appliance Inlet C14 with recessed Circuit Breaker TA45 C14 70 C Description Characteristics - Panel Mount: Screw-on version from front or rear side, snap-in version from front side - 2 Functions: Appliance Inlet Protection class I, circuit breaker type TA45 2-pole - Quick connect terminals 6.3 x 0.8 mm - All single elements are already wired - Switch non-illuminated or illuminated Thermal overload protection Optional with undervoltage- or remote trip release - Qualified for use in equipment according IEC/EN 60950 Other versions on request - Approvals - VDE Certificate Number: 40011305 - UL File Number: E96454 Unwired versions Line switch 1-pole Other rocker marking Variant with notch for V-Lock mating Cordsets References Alternative: version with line filter DF12 Substitute for type 6145 Weblinks General Product Information, Approvals, RoHS, CHINA-RoHS, Mating Connectors, e-Store, SCHURTER-Stock-Check, Distributor-StockCheck, Accessories Newly available variants corresponding to V-Lock mating cordset. The connector is equipped with a notch intended for use with the latching cordset. The cord latching system prevents against accidental removal of the cordset. Technical Data Ratings IEC Ratings UL/CSA Dielectric Strength Allowable Operation Temp. Degree of Protection Protection Class Terminal Panel Thickness s Material: Housing 10 A / 250 VAC; 50 Hz 1 - 15 A / 250 VAC; 60 Hz > 2.5 kVAC between L-N > 3 kVAC between L/N-PE (1 min/50 Hz) -10 C to 55 C from front side IP 40 acc. to IEC 60529 Suitable for appliances with protection class 1 acc. to IEC 61140 Quick connect terminals 6.3 x 0.8 mm Screw: max 8 mm Mounting screw torque max 0.5 Nm Snap-in: 1/1.5/2/2.5/3 mm Thermoplastic, black, UL 94V-0 Appliance Inlet Circuit Breakers Line Switch Connectors C14 acc. to IEC/EN 60320-1, UL 498, CSA C22.2 no. 42 (for cold conditions) pin-temperature 70 C, 10 A, Protection Class 1 Acc. IEC/EN 60934, UL 1077, CSA 22.2 no. 235 2-pole rocker switch, illuminated or nonilluminated. Optional with undervoltageor remote trip release Short circuit capacity Icn: at In < 3A/240VAC : 10 x In at In 3A/240VAC : 300A Rocker switch 2-pole, non-illuminated or illuminated, acc. to IEC 61058-1 Technical details DF11 Power entry modules without line filter www.schurter.com/pg05 Dimensions 91.5 mm * Version TA45 with undervoltage release Diagrams Diagram 1) Line 2) Load Connectors DF11 Power entry modules without line filter www.schurter.com/pg05 Connectors DF11 Power entry modules without line filter www.schurter.com/pg05 Technical data (continued) Circuit breaker Tripping characteristics In < 3 A Tripping characteristics In >_ 3... <_ 15 A [ min ] [ sec ] 10'000 [ min ] [ sec ] 10'000 Type TA45 Rated current In < 3 A 60 2000 30 20 1000 10 Ambient temp. Type TA45 Rated current 1-pole protected 60 2-pole protected 30 2'000 20 +23 C 2-pole protected 1'000 10 500 I n > 3... < 15 A 1-pole protected +23 C Ambient temp. 500 5 5 200 200 100 100 1 1 50 20 20 10 10 5 5 2 2 1 1 0,5 0,5 Tripping time Tripping time 50 0,3 0,2 0,1 1,05 1,32 2 3 4 5 Multiple of rated current 8 0,3 0,2 0,1 1,05 1,32 10 2 3 4 5 8 Multiple of rated current [ x In ] 10 [ x In ] Effect of ambient temperature 1) The unit is calibrated for an ambient temperature of +23 C. To determine the rated current for a lower or higher ambient temperature, use a correction factor from the table below. * Temperature must be measured at the rear of the breaker next to the terminals after equipment operating temperature has been reached. * Ambient temperature [C] Correction factor -10 0,89 - 5 0,91 0 0,92 +23 1,00 +30 1,03 +40 1,08 +55 1,16 Rated current at +23 C Ambient temperature Correction factor Chosen rated current at + 40 C ambient temperature 1) Example Order code (Order example) Type Specials 9 V-Lock-Notch Order code TA 45 (2-pole rocker-switch without accessories) DF11 . A B T W F 1 5 0 C 0 Wiring 1 wired 2 unwired . 0 0 1 0 . 0 1 9 see table 1 Protection class 0 Protection class I Mounting 0 Screw 1 Snap-in s = 1.0 mm 2 Snap-in s = 1.5 mm 3 Snap-in s = 2.0 mm 4 Snap-in s = 2.5 mm 5 Snap-in s = 3.0 mm Terminals 1 Quick connect 6.3 x 0.8 00 Without line filter Please note that Schurter will establish an internal part number for logistical use in addition to the order code. The format of this internal part number is, for example DF11.xxxxxxx Connectors 6,0 A +40 C 1,08 6 A x 1,08 = 6,5 A DF11 Power entry modules without line filter www.schurter.com/pg05 Packaging unit 20 Pcs Accessories Description 0859.0109 Rear Cover Assorted Covers Rear Cover Mating Outlets/Connectors Category / Description Appliance OutletOverview complete IEC Appliance Outlet F, Screw-on Mounting, Front Side, Solder Terminal 4787 IEC Appliance Outlet F, Snap-in Mounting, Front Side, Solder or Quick-connect Terminal 4788 IEC Appliance Outlet F or H, Screw-on Mounting, Front Side, Solder, PCB or Quick-connect Terminal 5091 IEC Appliance Outlet F or H, Screw-on Mounting, Front Side, Solder or Quick-connect Terminal 5092 Appliance Outletfurther types toDF11 ConnectorOverview complete IEC Connector C15, Rewireable, Straight 0101 IEC Connector C15A, Rewireable, Straight 0102 IEC Connector C15A, Rewireable, Straight 0102-G IEC Connector C15A, Rewireable, Angled 0112 IEC Connector C13, Rewireable, Angled 4012 Connectorfurther types toDF11 ... Power CordOverview complete Power Cord with IEC Connector C13, Angled 0311 Power Cord with IEC Connector C13, Angled 3011 Power Cord with IEC Connector C13, Angled 3012 Power Cord with IEC Connector C13, Angled 3013 Power Cord with IEC Connector C13 3020 Power Cordfurther types toDF11 ... The specifications, descriptions and illustrations indicated in this document are based on Connectors current information. All content is subject to modifications and amendments.