© Semiconductor Components Industries, LLC, 2006
July, 2006 − Rev. 4 1Publication Order Number:
MUR260/D
MUR260
Preferred Device
SWITCHMODEt
Power Rectifier
These state−of−the−art devices are designed for use in switching
power supplies, inverters and as free wheeling diodes.
Features
Ultrafast 50 Nanosecond Recovery Times
175°C Operating Junction Temperature
Low Forward Voltage
Low Leakage Current
High Temperature Glass Passivated Junction
These are Pb−Free Devices*
Mechanical Characteristics:
Case: Epoxy, Molded
Weight: 0.4 Gram (Approximately)
Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
Lead Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
Shipped in Plastic Bags; 1,000 per Bag
Available Tape and Reel; 5,000 per Reel, by Adding a “RL’ Suffix to
the Part Number
MAXIMUM RATINGS
Rating Symbol Value Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
600
V
Average Rectified Forward Current (Note 1)
(Square Wave Mounting Method #3 Per Note 3) IF(AV) 2.0 @
TA = 60°CA
Non-Repetitive Peak Surge Current
(Surge applied at rated load conditions,
halfwave, single phase, 60 Hz)
IFSM 35 A
Operating Junction Temperature and Storage
Temperature Range TJ, Tstg 65 to
+175 °C
THERMAL CHARACTERISTICS
Characteristics Symbol Value Unit
Maximum Thermal Resistance,
Junction−to−Ambient RqJA See
Note 3 °C/W
Stresses exceeding Maximum Ratings may damage the device. Maximum
Ratings are stress ratings only. Functional operation above the Recommended
Operating Conditions is not implied. Extended exposure to stresses above the
Recommended Operating Conditions may affect device reliability.
1. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
ULTRAFAST RECTIFIER
2.0 AMPERES, 600 VOLTS
Preferred devices are recommended choices for future use
and best overall value.
http://onsemi.com
For information on tape and reel specifications,
including part orientation and tape sizes, please
refer t o our Tape and Reel Packaging Specification
s
Brochure, BRD8011/D.
PLASTIC
AXIAL LEAD
CASE 59
MARKING DIAGRAM
**This package is inherently Pb−Free.
A = Assembly Location
Y = Year
WW = Work Week
G= Pb−Free Package
(Note: Microdot may be in either location)
A
MUR260
YYWW G
G
Device Package Shipping
ORDERING INFORMATION
MUR260RL Axial Lead** 5000/Tape & Ree
l
MUR260 Axial Lead** 1000 Units/Bag
MUR260G Axial Lead** 1000 Units/Bag
MUR260RLG Axial Lead** 5000/Tape & Ree
l
MUR260
http://onsemi.com
2
ELECTRICAL CHARACTERISTICS
Characteristics Symbol Value Unit
Maximum Instantaneous Forward Voltage (Note 2)
(IF = 2.0 Amp, TJ = 150°C)
(IF = 2.0 Amp, TJ = 25°C)
vF1.15
1.35
V
Maximum Instantaneous Reverse Current (Note 2)
(Rated dc Voltage, TJ = 150°C)
(Rated dc Voltage, TJ = 25°C)
iR150
5.0
mA
Maximum Reverse Recovery Time
(IF = 1.0 Amp, di/dt = 50 Amp/ms)
(IF = 0.5 Amp, IR = 1.0 Amp, IREC = 0.25 A)
trr 75
50
ns
Maximum Forward Recovery Time
(IF = 1.0 A, di/dt = 100 A/ms, IREC to 1.0 V) tfr 50 ns
2. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%.
VF, INSTANTANEOUS VOLTAGE (VOLTS)
2.1
1.0
10
IF
0.1
0.5 1.50.7 1.7 1.9
Figure 1. Maximum Forward Voltage
, INSTANTANEOUS FORWARD CURRENT (AMPS)
0.9 1.1 1.3
75°C
VF @ 150°C
25°C
125°C
Figure 2. Typical Forward Voltage
VF, INSTANTANEOUS VOLTAGE (VOLTS)
0.5 0.7
0.1
10
, INSTANTANEOUS FORWARD CURRENT (AMPS)
F
2.10.9
1.0
1.5 1.9
75°C
VF @ 150°C
25°C
i
1.1 1.3 1.7
125°C
MUR260
http://onsemi.com
3
Figure 3. Maximum Reverse Current Figure 4. Typical Reverse Current
Figure 5. Current Derating Figure 6. Power Dissipation
Figure 7. Typical Capacitance
0
10
30
50
5.0
10 20
VR, REVERSE VOLTAGE (VOLTS)
C, CAPACITANCE (pF)
TJ = 25°C
30 40 50
7.0
20
0
0.1
10
100
40 60
VR, REVERSE VOLTAGE (VOLTS)
80 160 200
1.0
IR, REVERSE CURRENT ( A)m
100 120 140 180
75°C
TJ = 150°C
25°C
125°C
20
VR, REVERSE VOLTAGE (VOLTS)
0 15075 225
0.001
0.1
1.0
IR
600
375300
0.01
, REVERSE CURRENT ( A)
125°C
25°C
m
100
525450
75°C
IR @ 150°C
10
dc
TA, AMBIENT TEMPERATURE (°C)
050
0
2.0
1.0
3.0
5.0
4.0
I
200150100
, AVERAGE FORWARD CURRENT (AMPS)
F(AV)
SQUARE WAVE
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
0
1.0
3.0
2.0
PF(AV)
0
0.5 1.0 1.5 2.0 3.0
, AVERAGE POWER DISSIPATION (WATTS)
SQUARE WAVE dc
2.5
MUR260
http://onsemi.com
4
Lead Length, L
Mounting
Method 1/8 1/4 1/2 Units
1
2
3
52
67
RqJA
65 72
80 87
50
°C/W
°C/W
°C/W
TYPICAL VALUES FOR RqJA IN STILL AIR
Data shown for thermal resistance, junction−to−ambient
(RqJA) for the mountings shown is to be used as typical
guideline values for preliminary engineering or in case the
tie point temperature cannot be measured.
NOTE 3 — AMBIENT MOUNTING DATA
MOUNTING METHOD 1
MOUNTING METHOD 2
MOUNTING METHOD 3
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
L L
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
L L
Vector Pin Mounting
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
L = 3/8
Board Ground Plane
P.C. Board with
1−1/2 X 1−1/2 Copper Surface
MUR260
http://onsemi.com
5
PACKAGE DIMENSIONS
B
D
K
K
F
F
A
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A4.10 5.200.161 0.205
B2.00 2.700.079 0.106
D0.71 0.860.028 0.034
F−−− 1.27−−− 0.050
K25.40 −−−1.000 −−−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO−41 OUTLINE SHALL APPLY
4. POLARITY DENOTED BY CATHODE BAND.
5. LEAD DIAMETER NOT CONTROLLED WITHIN F
DIMENSION.
AXIAL LEAD
CASE 59−10
ISSUE U
POLARITY INDICATOR
OPTIONAL AS NEEDED
(SEE STYLES) STYLE 1:
PIN 1. CATHODE (POLARITY BAND)
2. ANODE
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its of ficers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
MUR260/D
SWITCHMODE is a trademark of Semiconductor Components Industries, LLC.
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative