Monitoring Relays AC Current Transformer Types A 82-10, A 82-20 * 5 types of input: 0 - 25 AAC 0 - 50 AAC 0 - 100 AAC 0 - 250 AAC 0 - 500 AAC * Output: A 82-10: 0 - 20 mADC (source) A 82-20: 4 - 20 mADC (sink) * Easy interface to PLC or setpoint relays Product Description Ordering Key AC current metering transformer for 25, 50, 100, 250 or 500 AAC. Output current from the transformer is 0-20 mADC or 4-20 mADC in accordance with IEC 60381-1. Can be used with relays DIB01, PIB01, DIC01, PIC01 or S183 or directly connected to a PLC. Power supply ON is indicated by a green LED on the side of the housing. Type Output Input current Input current Output current Type no. 25 AAC 50 AAC 100 AAC 250 AAC 500 AAC 0 - 20 mA 0 - 20 mA 0 - 20 mA 0 - 20 mA 0 - 20 mA A 82-10 25 A 82-10 50 A 82-10 100 A 82-10 250 A 82-10 500 25 AAC 50 AAC 100 AAC 250 AAC 500 AAC 4 - 20 mA 4 - 20 mA 4 - 20 mA 4 - 20 mA 4 - 20 mA A 82-20 25 A 82-20 50 A 82-20 100 A 82-20 250 A 82-20 500 A 82-10 50 Type Selection Input Specifications A 82-10/20 25 Current range 0 - 25 AAC Max. current (continuously) 30 AAC Max. overload current (t = 30 s) 250 AAC Rated insulation voltage Input - output 1000 VAC rms Overvoltage category IV (IEC 60664) Dielectric strength Dielectric voltage 6 kVAC rms Rated impulse withstand volt. 12 kV (1.2/50 s) A 82-10/20 50 0 - 50 AAC 60 AAC 300 AAC A 82-10/20 100 0 - 100 AAC 120 AAC 700 AAC A 82-10/20 250 0 - 250 AAC 300 AAC 1500 AAC A 82-10/20 500 0 - 500 AAC 600 AAC 3000 AAC 1000 VAC rms IV (IEC 60664) 1000 VAC rms IV (IEC 60664) 1000 VAC rms IV (IEC 60664) 1000 VAC rms IV (IEC 60664) 6 kVAC rms 12 kV (1.2/50 s) 6 kVAC rms 12 kV (1.2/50 s) 6 kVAC rms 12 kV (1.2/50 s) 6 kVAC rms 12 kV (1.2/50 s) Specifications are subject to change without notice (25.01.06) 1 A 82-10, A 82-20 Output Specifications General Specifications Rated insulation voltage (cable) Output current 10: 20: Power supply (loop voltage) Tolerance of output current @ 50 Hz A 82-10 A 82-20 Temperature variation 250 VACrms 0 - 20 mADC 4 - 20 mADC 10 - 40 VDC Power ON delay Reaction time Frequency range 40 Hz -1 kHz Frequency variation 10 ppm/Hz Maximum output current 35 mADC Indication for Power supply ON Environment Degree of protection Pollution degree Operating temperature Housing Dimensions Material Weight A 82-10 A 82-20 Connection cable A 82-10 A 82-20 Approval CE marking EMC Immunity 2% 0.08 mA 2% 400 ppm/C Emission <1s < 100 ms worst case reaction time may be up to 5 x LED, green IP 20 3 (IEC 60664) -20 to 50C (-4 to +122 F) 95 x 67.5 x 20 mm ABS 300 g 270 g 2 m, 3 x 0.25 mm2 2 m, 2 x 0.25 mm2 UL Yes Electromagnetic Compatibility Acc. to EN 61000-6-1 (tolerance of output current: 2%) Acc. to EN 61000-6-2 (tolerance of output current: 5%) Acc. to EN 61000-6-3 Mode of Operation A 82-10, A 82-20 are current metering transformers with standard source/sink output 0 - 20 mA/4 - 20 mA. This makes it very useful as an AC current interface to a PLC with mADC input. Used with relays DIB01, PIB01, DIC01, PIC01 or S183 one or more setpoints can monitor the current and signal alarm. S 183 also provides the DC voltage supply for the A 82-10, A 82-20. The metered conductor is drawn through the central hole of the current metering transformer. It is possible to meter currents below the nominal range by drawing the conductor through the hole several times. If the conductor is drawn through the central hole e.g. 5 times, the transformer will register 50 A when the current in the conductor is 10 A. A 82-10 has factory-set gain (span) adjustment, whereas A 82-20 has zero as well as gain (span) adjustment, both factory-set. Note: Do not change the set values. Wiring Diagrams A 82-10 ... (source) A 82-20 ... (sink) I I Grey Red 2 Black Black R load Power + supply Loop + voltage R load Yellow Specifications are subject to change without notice (25.01.06) A 82-10, A 82-20 Input/Output Curve Resistance/Voltage Curve Output (mADC) Max. R load () 20 16 12 8 4 A 0 -2 82 A 0 -1 82 50 100 Input (% of range) (V) Power supply (loop voltage) Max. load resistance versus Power supply (loop voltage) Dimensions Specifications are subject to change without notice (25.01.06) 3