VS-ST180SPbF Series www.vishay.com Vishay Semiconductors Phase Control Thyristors (Stud Version), 200 A FEATURES * Center amplifying gate * International standard case TO-93 (TO-209AB)) * Hermetic metal case with ceramic insulator * Compression bonded encapsulation for heavy duty operations such as severe thermal cycling TO-93 (TO-209AB) * Designed and qualified for industrial level * Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 PRIMARY CHARACTERISTICS TYPICAL APPLICATIONS IT(AV) 200 A VDRM/VRRM 1600 V, 2000 V VTM 1.75 V IGT 150 mA TJ -40 C to +125 C Package TO-93 (TO-209AB) Circuit configuration Single SCR * DC motor controls * Controlled DC power supplies * AC controllers MAJOR RATINGS AND CHARACTERISTICS PARAMETER TEST CONDITIONS IT(AV) TC IT(RMS) ITSM I2t A 85 C 314 A 5000 60 Hz 5230 50 Hz 125 60 Hz 114 Typical TJ UNITS 200 50 Hz VDRM/VRRM tq VALUES A kA2s 1600 to 2000 V 100 s -40 to +125 C IDRM/IRRM MAXIMUM AT TJ = TJ MAXIMUM mA ELECTRICAL SPECIFICATIONS VOLTAGE RATINGS TYPE NUMBER VS-ST180S VOLTAGE CODE VDRM/VRRM, MAXIMUM REPETITIVE PEAK AND OFF-STATE VOLTAGE V VRSM, MAXIMUM NON-REPETITIVE PEAK VOLTAGE V 16 1600 1700 20 2000 2100 30 Revision: 27-Sep-17 Document Number: 94397 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-ST180SPbF Series www.vishay.com Vishay Semiconductors ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL Maximum average on-state current at case temperature Maximum RMS on-state current Maximum peak, one-cycle non-repetitive surge current IT(AV) IT(RMS) ITSM TEST CONDITIONS 180 conduction, half sine wave No voltage reapplied 5000 100 % VRRM reapplied 4200 t = 10 ms t = 8.3 ms t = 10 ms t = 8.3 ms Maximum I2t for fusing I2t C t = 10 ms t = 10 ms I2t A 85 314 t = 8.3 ms No voltage reapplied 5230 Sinusoidal half wave, initial TJ = TJ maximum 100 % VRRM reapplied 125 114 88 t = 0.1 to 10 ms, no voltage reapplied 1250 VT(TO)1 (16.7 % x x IT(AV) < I < x IT(AV)), TJ = TJ maximum 1.08 VT(TO)2 (I > x IT(AV)), TJ = TJ maximum 1.14 Low level value of on-state slope resistance rt1 (16.7 % x x IT(AV) < I < x IT(AV)), TJ = TJ maximum 1.18 High level value of on-state slope resistance rt2 (I > x IT(AV)), TJ = TJ maximum 1.14 Ipk = 570 A, TJ = 125 C, tp = 10 ms sine pulse 1.75 VTM IH Maximum (typical) latching current IL TJ = TJ maximum, anode supply 12 V resistive load kA2s 81 High level value of threshold voltage Maximum on-state voltage A 4400 Low level value of threshold voltage Maximum holding current UNITS 200 DC at 76 C case temperature t = 8.3 ms Maximum I2t for fusing VALUES 600 1000 (300) kA2s V m V mA SWITCHING PARAMETER Maximum non-repetitive rate of rise of turned-on current SYMBOL dI/dt TEST CONDITIONS Gate drive 20 V, 20 , tr 1 s TJ = TJ maximum, anode voltage 80 % VDRM VALUES UNITS 1000 A/s Typical delay time td Gate current 1 A, dIg/dt = 1 A/s Vd = 0.67 % VDRM, TJ = 25 C 1.0 Typical turn-off time tq ITM = 300 A, TJ = TJ maximum, dI/dt = 20 A/s, VR = 50 V, dV/dt = 20 V/s, gate 0 V 100 , tp = 500 s 100 SYMBOL TEST CONDITIONS VALUES UNITS s BLOCKING PARAMETER Maximum critical rate of rise of off-state voltage dV/dt TJ = TJ maximum linear to 80 % rated VDRM 500 V/s Maximum peak reverse and off-state leakage current IRRM, IDRM TJ = TJ maximum, rated VDRM/VRRM applied 30 mA Revision: 27-Sep-17 Document Number: 94397 2 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-ST180SPbF Series www.vishay.com Vishay Semiconductors TRIGGERING PARAMETER Maximum peak gate power Maximum average gate power SYMBOL PGM PG(AV) Maximum peak positive gate current IGM Maximum peak positive gate voltage + VGM Maximum peak negative gate voltage - VGM DC gate current required to trigger IGT DC gate current not to trigger IGD DC gate voltage not to trigger VGD MAX. 10 TJ = TJ maximum, f = 50 Hz, d% = 50 2.0 TJ = TJ maximum, tp 5 ms 3.0 TJ = TJ maximum, tp 5 ms 20 A V 5.0 TJ = - 40 C 180 - 90 150 40 - Maximum required gate trigger/ current/voltage are the lowest value which will trigger all units 12 V anode to cathode applied TJ = 25 C TJ = 125 C 2.9 - 1.8 3.0 1.2 TJ = TJ maximum Maximum gate current/voltage not to trigger is the maximum value which will not trigger any unit with rated VDRM anode to cathode applied UNITS W TJ = 25 C TJ = - 40 C VGT TYP. TJ = TJ maximum, tp 5 ms TJ = 125 C DC gate voltage required to trigger VALUES TEST CONDITIONS mA V 10 mA 0.25 V VALUES UNITS THERMAL AND MECHANICAL SPECIFICATIONS PARAMETER Maximum operating junction temperature range SYMBOL TEST CONDITIONS TJ -40 to +125 Maximum storage temperature range TStg -40 to +150 Maximum thermal resistance, junction to case RthJC Maximum thermal resistance, case to heatsink RthC-hs DC operation 0.105 Mounting surface, smooth, flat and greased 0.04 Non-lubricated threads 31 (275) Lubricated threads 24.5 (210) C K/W Mounting torque, 10 % Approximate weight 280 Case style See dimensions - link at the end of datasheeet N*m (lbf in) g TO-93 (TO-209AB) RthJC CONDUCTION CONDUCTION ANGLE SINUSOIDAL CONDUCTION RECTANGULAR CONDUCTION 180 0.015 0.012 120 0.019 0.020 90 0.025 0.027 60 0.036 0.037 30 0.060 0.060 TEST CONDITIONS UNITS TJ = TJ maximum K/W Note * The table above shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC Revision: 27-Sep-17 Document Number: 94397 3 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-ST180SPbF Series Vishay Semiconductors Maximum Allowable Case Temperature (C) Maximum Allowable Case Temperature (C) www.vishay.com 130 ST180S Series RthJC (DC) = 0.105 K/ W 120 110 Conduc tion Angle 100 30 60 90 120 90 180 80 0 40 80 120 160 200 240 130 ST180S Series R thJC (DC) = 0.105 K/ W 120 110 Conduc tion Period 100 90 30 80 120 180 DC 70 0 50 100 150 200 250 300 350 Average On-state Current (A) Average On-state Current (A) Fig. 1 - Current Ratings Characteristics Fig. 2 - Current Ratings Characteristics 350 08 0. W K/ K/ W K/ W ta el -D RMSLimit 0.4 K/ W 150 Conduc tion Angle 0.5 K/ W 0.8 K/ W 1.2 K /W 100 ST180SSeries TJ = 125C 50 R 200 = 0.3 K/ W A 0. 2 W K/ 250 0. 16 hS Rt 180 120 90 60 30 300 1 0. Maximum Average On-state Power Loss (W) 60 90 0 0 40 80 120 160 200 240 25 Average On-state Current (A) 50 75 100 125 Maximum Allowable Ambient Temperature (C) Maximum Average On-state Power Loss (W) Fig. 3 - On-State Power Loss Characteristics 500 DC 180 120 90 60 30 450 400 350 300 R 0. 1 0. 16 250 RMSLimit 200 Conduction Period 150 100 ST180SSeries TJ = 125C 50 th SA = K/ W 0. 08 K/ W 0.2 K/ W 0.3 K/ W 0.4 K/ W 0.5 K/ W 0.8 K /W K/ W -D el ta R 1.2 K/ W 0 0 40 80 120 160 200 240 280 320 25 Average On-state Current (A) 50 75 100 125 Maximum Allowable Ambient Temperature (C) Fig. 4 - On-State Power Loss Characteristics Revision: 27-Sep-17 Document Number: 94397 4 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-ST180SPbF Series Vishay Semiconductors 4800 Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) www.vishay.com At Any Rated Load Condition And With Rated VRRM Applied Following Surge. 4400 Initial TJ = 125C @ 60 Hz 0.0083 s 4000 @ 50 Hz 0.0100 s 3600 3200 2800 2400 ST180SSeries 2000 1 10 100 5500 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control 5000 Of Conduction May Not Be Maintained. Initial TJ = 125C 4500 No Voltage Reapplied Rated VRRM Reapplied 4000 3500 3000 2500 ST180SSeries 2000 0.01 0.1 1 Pulse Train Duration (s) Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Current Fig. 6 - Maximum Non-Repetitive Surge Current Instantaneous On-state Current (A) 10000 TJ = 25C TJ = 125C 1000 ST180SSeries 100 0.5 1 1.5 2 2.5 3 3.5 4 4.5 5 5.5 6 Instantaneous On-state Voltage (V) Transient Thermal Impedance Z thJC (K/ W) Fig. 7 - On-State Voltage Drop Characteristics 1 Steady State Value RthJC = 0.105 K/ W (DC Operation) 0.1 0.01 ST180S Series 0.001 0.001 0.01 0.1 1 10 Square Wave Pulse Duration (s) Fig. 8 - Thermal Impedance ZthJC Characteristics Revision: 27-Sep-17 Document Number: 94397 5 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VS-ST180SPbF Series www.vishay.com Vishay Semiconductors Rec tangular gate pulse a) Recommended load line for rated di/ dt : 20V, 10ohms; tr<=1 s b) Rec ommended load line for <=30% rated di/ dt : 10V, 10ohms 10 tr<=1 s (b) VGD IGD 0.1 0.001 (1) PGM = 10W, (2) PGM = 20W, (3) PGM = 40W, (4) PGM = 60W, = 4ms = 2ms = 1ms = 0.66ms (a) (1) Device: ST180S Series 0.01 tp tp tp tp Tj=-40 C 1 Tj=25 C Tj=125 C Instantaneous Gate Voltage (V) 100 (2) (3) (4) Frequency Limited by PG(AV) 0.1 1 10 100 Instantaneous Gate Current (A) Fig. 9 - Gate Characteristics ORDERING INFORMATION TABLE Device code VS- ST 18 0 S 20 P 0 PbF 1 2 3 4 5 6 7 8 9 1 - Vishay Semiconductors product 2 - Thyristor 3 - Essential part number 4 - 0 = converter grade 5 - S = compression bonding stud 6 - Voltage code x 100 = VRRM (see Voltage Ratings table) 7 - P = stud base 3/4"-16UNF2A threads 8 - 0 = eyelet terminals (gate and auxiliary cathode leads) 9 - 1 = fast-on terminals (gate and auxiliary cathode leads) None = standard production PbF = lead (Pb)-free Note: For metric device M16 x 1.5 contact factory LINKS TO RELATED DOCUMENTS Dimensions www.vishay.com/doc?95082 Revision: 27-Sep-17 Document Number: 94397 6 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Outline Dimensions www.vishay.com Vishay Semiconductors TO-209AB (TO-93) DIMENSIONS in millimeters (inches) 7) MI N. 4 (0.16) MAX. 19 (0.75) MAX. (0. 3 8.5 (0.33) DIA. C.S. 0.4 mm2 (0.0006 s.i.) Red cathode White gate Red shrink 38.5 (1.52) MAX. 16 (0.63) MAX. White shrink 220 (8.66) 10 (0.39) Red silicon rubber 90 (3.54) MIN. 210 (8.26) 10 (0.39) 22 Flexible leads C.S. 25 mm2 (0.039 s.i.) ( 0. 86 )M 9.5 4.3 (0.17) DIA. IN . Glass metal seal Fast-on terminals AMP. 280000-1 REF-250 28.5 (1.12) MAX. DIA. 27.5 (1.08) MAX. SW 32 3/4"-16UNF-2A (1) 35 (1.38) MAX. 19 (0.75) MAX. )M IN . 4 (0.16) MAX. 37 8.5 (0.33) DIA. C.S. 0.4 mm2 (0.006 s.i.) Red cathode White gate White shrink 16 (0.63) MAX. 38.5 (1.52) MAX. Red shrink . IN (0. 22 220 (8.66) 10 (0.39) Red silicon rubber 90 (3.54) MIN. 210 (8.26) 10 (0.39) Flexible leads C.S. 25 mm2 (0.039 s.i.) 86 9.5 (0. 4.3 (0.17) DIA. )M Ceramic housing 27.5 (1.08) MAX. DIA. 27.5 (1.08) MAX. SW 32 3/4"-16UNF-2A (1) 35 (1.38) MAX. Note (1) For metric device: M16 x 1.5 - length 21 (0.83) maximum Revision: 05-Mar-12 Document Number: 95082 1 For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, "Vishay"), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. (c) 2017 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 08-Feb-17 1 Document Number: 91000 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Vishay: ST180S04P1V ST180S06P1V ST180S08P1V ST180S12P1V ST180S16P1 VS-ST180S12P0V VSST180S12P0VPBF VS-ST180S04P1VPBF VS-ST180S06P1VPBF ST180S04P0V VS-ST180S08P0V ST180S16P0 ST180S20P0 ST180S20P1 VS-ST180S20P1PBF VS-ST180S04P0VPBF VS-ST180S08P0VPBF VSST180S16P1PBF VS-ST180S16P0PBF VS-ST180S12P1VPBF VS-ST180S20P0PBF VS-ST180S12P1V VSST180S04P0V VS-ST180S20P0 VS-ST180S16P0 VS-ST180S16M0LPBF