C-TYPE 3.3, 5.0 volt CMOS Oscillator Not recommended for new designs Features * CMOS output * Output frequencies to 190 MHz * Low jitter, Fundamental or 3rd OT Crystal * Tri-state output for board test and debug * Gold over nickel contact pads * Hermetically sealed ceramic SMD package * Product is compliant to RoHS directive and fully compatible with lead free assembly The C-TYPE Crystal Oscillator Applications * SONET/SDH/DWDM * Ethernet, Gigabit Ethernet * Storage Area Network * Digital Video * Broadband Access * Microprocessors/DSP/FPGA fo Output Buffer / Disable Description Vectron's C-TYPE Crystal Oscillator (XO) is quartz stabilized square wave generator with a CMOS output, operating off a 1.8, 2.5, 3.3, or 5.0 volt supply. The C-TYPE uses fundamental or 3rd overtone crystals resulting in low jitter performance, typically 0.5ps rms in the 12 kHz to 20MHz band. Also a monolithic IC, which improves reliability and reduces cost, is hermitically sealed. Vectron International 267 Lowell Road, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com C-TYPE Data Sheet Performance Characteristics Table 1. Electrical Performance, 5V option Parameter Symbol Frequency fO 1 Operating Supply Voltage VDD Absolute Maximum Supply Voltage Supply Current, Output Enabled IDD <1.5 MHz 1.5 to 20 MHz 20.01 to 50 MHz 50.01 to 85 MHz 85.01 to 125 MHz Supply Current, Out disabled IDD Output Logic Levels Output Logic High2 VOH Output Logic Low2 VOL Output Logic High Drive IOH Output Logic Low Drive IOL Output Rise/Fall Time2 tR/tF < 1.00 MHz 1.0 to 20.00 MHz 20.01 to 50.00 MHz 50.01 to 125.00 MHz Duty Cycle3 (ordering option) SYM Operating Temperature (ordering option) Storage Temperature Stability4 (ordering option) RMS Jitter, 12kHz to 20 MHz Period Jitter, RMS Output Enable/Disable5 Output Enabled Output Disabled Internal Enable Pull-Up resistor5 Start-up time Min 0.012 4.5 -0.7 Typical Maximum 125.000 5.5 7.0 5.0 7 10 30 50 60 30 0.9*VDD 0.1*VDD 16 16 Units MHz V V mA uA V V mA mA ns 200 8 5 2 45/55 -10/70 or -40/85 -55 125 20, 25, 32, 50, 100 0.5 1 2.5 % C C ppm ps ps V 4.0 0.8 100 10 Kohm ms 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Figure 1 defines these parameters. Figure 2 illustrates the operating conditions under which these parameters are tested and specified. 3. Symmetry is measured defined as On Time/Period. 4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under operation). 5. Output will be enabled if enable/disable is left open. tR tF I DD V OH 50% VD D V OL + - 4 . 1F .01F 1 2 3 IC On Time VC Period Figure 1. Output Waveform Vectron International 267 Lowell Rd, Hudson NH 03051 + 15pF - Figure 2. Typical Output Test Conditions (255C) Tel: 1-88-VECTRON-1 e-mail: vectron@vectron.com C-TYPE Data Sheet Table 2. Electrical Performance, 3.3V option Parameter Symbol Frequency fO Operating Supply Voltage 1 VDD Absolute Maximum Operating Voltage Supply Current, Output Enabled IDD < 1.500 MHz 1.5 to 20 MHz 20.01 to 50 MHz 50.01 to 85 MHz 85.01 to 190 MHz Supply Current, Output disabled IDD Output Logic Levels Output Logic High2 VOH Output Logic Low2 VOL Output Logic High Drive IOH Output Logic Low Drive IOL Output Rise/Fall Time2 tR/tF < 1.00 MHz 1.00 to 20.00 MHz 20.01 to 50.00 MHz 50.01 to 90.00 MHz 90.01 to 190.00 MHz Duty Cycle3 (ordering option) SYM Operating Temperature (ordering option) Storage Temperature Stability4 (ordering option) RMS Jitter, 12kHz to 20 MHz RMS Jitter Output Enable/Disable5 Output Enabled Output Disabled Internal Enable Pull-Up resistor5 Start-up time Min 0.012 2.97 -0.5 Typical Maximum 190.000 3.63 5.0 3.3 5 7 20 30 50 30 0.9*VDD 0.1*VDD 8 8 Units MHz V V mA uA V V mA mA ns 200 6 4 3 2 45/55 -10/70 or -40/85 -55 125 20, 25, 32, 50, 100 0.5 1 2.5 % C C ppm ps ps V 2.0 0.5 100 10 Kohm ms 1. A 0.01uF and a 0.1uF capacitor should be located as close to the supply as possible (to ground) is recommended. 2. Figure 3 defines these parameters. Figure 4 illustrates the operating conditions under which these parameters are tested and specified. For Fo>90MHz, rise and fall time is measured 20 to 80%. 3. Symmetry is measured defined as On Time/Period. 4. Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under operation). 5. Output will be enabled if enable/disable is left open. tR tF I DD V OH 50% VD D V OL + - 4 . 1F .01F 1 2 3 IC On Time VC Period Figure 3. Output Waveform Vectron International 267 Lowell Rd, Hudson NH 03051 + 15pF - Figure 4. Typical Output Test Conditions (255C) Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com C-TYPE Data Sheet Enable/Disable Functional Description Under normal operation the Enable/Disable is left open or set to a logic high state. When the E/D is set to a logic low, the oscillator stops and the output is in a high impedance state. This helps reduce power consumption as well as facilitating board testing and troubleshooting. Tri-state Functional Description Under normal operation the tri-state is left open or set to a logic high state. When the tri-state is set to a logic low, the oscillator remains active but the output buffer is in a high impedance state. This helps facilitate board testing and troubleshooting. Table 3. Outline Diagrams, Pad Layout and Pin Out Pin # Symbol Function 1 2 3 4 E/D or NC GND fO V DD Tri-state, Enable/Disable or NC Electrical and Case Ground Output Frequency Supply Voltage Contact Pads are gold over nickel Figure 9, Package drawing Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com C-TYPE Data Sheet Contact Pads are gold over nickel Figure 10, Alternate Package drawing Tape and Reel Table 4: Tape and Reel Dimensions (mm) J F D G C B A L I E H Tape Dimensions Product A C-TYPE 16 B C D E 7.5 1.5 4 8 Vectron International 267 Lowell Rd, Hudson NH 03051 K Reel Dimensions F G H 2 21 13 Tel: 1-88-VECTRON-1 I J K L 60 2 17 180 e-mail vectron@vectron.com # Per Reel 1000 C-TYPE Data Sheet Reliability The C-TYPE qualification tests have included: Table 5. Environnemental Compliance Parameter Mechanical Shock Mechanical Vibration Temperature Cycle Solderability Gross and Fine Leak Resistance to Solvents Moisture Sensitivity Level Contact Pads Conditions MIL-STD-883 Method 2022 MIL-STD-883 Method 2007 MIL-STD-883 Method 1010 MIL-STD-883 Method 2003 MIL-STD-883 Method 1014 MIL-STD-883 Method 2015 1 Gold over Nickel Handling Precautions Although ESD protection circuitry has been designed into the the C-TYPE, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model. Although no industry wide standard has been adopted for the CDM, a standard HBM of resistance = 1.5kohms and capacitance = 100pF is widely used and therefore can be used for comparison purposes. Table 6. ESD Ratings Model Human Body Model Charged Device Model Minimum 1000 1500 Conditions MIL-STD-883 Method 3115 JESD 22-C101 Suggested IR profile Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions, Table 9 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C. Table 7. Reflow Profile Parameter Symbol Value Preheat Time Ramp Up tS 150 sec Min, 200 sec Max R UP 3 oC/sec Max o Time Above 217 C Time To Peak Temperature tL 60 sec Min, 150 sec Max t AMB-P 480 sec Max Time At 260 oC (max) tP 10 sec Max Time At 240 C (max) tp2 60 sec Max R DN 6 oC/sec Max Ramp Down Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com C-TYPE Data Sheet Ordering Information C X X X X X - 25M000 Supply Voltage Output Frequency C=5.0V (10%) In MHZ D=3.3V (10%) Symmetry Type A=45/55%,TTL, 50pf F: No Tristate J=45/55%, CMOS, 15pf T: Tristate R=45/55%, TTL,50pf Stability P=45/55%, CMOS 50pf C : 20ppm Temperature Options D: 25ppm C: 0 to 70C E: 30ppm D: -10 to 70C F: 32ppm E: 0 to 85C G: 50ppm H: -20 to 70C H: 100ppm L: -40 to 85C Note: Not all combinations are available. For Additional Information, Please Contact: www.vectron.com USA: Vectron International * 267 Lowell Road, Hudson, NH 03051 * Tel: 1-88-VECTRON-1 * Fax: 1-888-FAX-VECTRON EUROPE: Landstrasse, D-74924, Neckarbischofsheim, Germany * Tel: 49 (0) 7268 8010 * Fax: 49 (0) 7268 801281 ASIA: Vectron Asia Pacific Sales 1F~2F. No.8 Workshop No.308 Fenju Rd., WaiGaoQiao Free Trade Zone, Pudong New Area Shanghai, China 200131 *Tel: 8621 50480777 * Fax: 8621 50481881 October27, 2006 Vectron International 267 Lowell Rd, Hudson NH 03051 Tel: 1-88-VECTRON-1 e-mail vectron@vectron.com