LM4132
VIN
Input
5V Output
2.5V
VREF
EN
GND
Enable
CIN COUT
**
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
LM4132 SOT-23 Precision Low Dropout Voltage Reference
Check for Samples: LM4132
1FEATURES DESCRIPTION
The LM4132 family of precision voltage references
2• Output Initial Voltage Accuracy 0.05% performs comparable to the best laser-trimmed
• Low Temperature Coefficient 10ppm/°C bipolar references, but in cost effective CMOS
• Low Supply Current, 60µA technology. The key to this break through is the use
of EEPROM registers for correction of curvature,
• Enable Pin Allowing a 3µA Shutdown Mode tempco, and accuracy on a CMOS bandgap
• 20mA Output Current architecture that allows package level programming
• Voltage Options 1.8V, 2.048V, 2.5V, 3.0V, 3.3V, to overcome assembly shift. The shifts in voltage
4.096V accuracy and tempco during assembly of die into
plastic packages limit the accuracy of references
• Custom Voltage Options Available (1.8V to trimmed with laser techniques.
4.096V) Unlike other LDO references, the LM4132 is capable
• VIN Range of VREF + 400mV to 5.5V @ 10mA of delivering up to 20mA and does not require an
• Stable with Low ESR Ceramic Capacitors output capacitor or buffer amplifier. These
• SOT23-5 Package advantages and the SOT23 packaging are important
for space-critical applications.
APPLICATIONS Series references provide lower power consumption
• Instrumentation & Process Control than shunt references, since they do not have to idle
the maximum possible load current under no load
• Test Equipment conditions. This advantage, the low quiescent current
• Data Acquisition Systems (60µA), and the low dropout voltage (400mV) make
• Base Stations the LM4132 ideal for battery-powered solutions.
• Servo Systems The LM4132 is available in five grades (A, B, C, D
• Portable, Battery Powered Equipment and E) for greater flexibility. The best grade devices
(A) have an initial accuracy of 0.05% with a specified
• Automotive & Industrial temperature coefficient of 10ppm/°C or less, while the
• Precision Regulators lowest grade parts (E) have an initial accuracy of
• Battery Chargers 0.5% and a tempco of 30ppm/°C.
• Communications
• Medical Equipment
Typical Application Circuit
*Note: The capacitor CIN is required and the capacitor COUT is optional.
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2005–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
VIN
1
2
3
5
4
EN
GND
N/C VREF
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Connection Diagram
(Top View)
See Package Number DBV0005A
PIN DESCRIPTIONS
Pin # Name Function
1 N/C No connect pin, leave floating
2 GND Ground
3 EN Enable pin
4 VIN Input supply
5 VREF Reference output
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
Absolute Maximum Ratings(1)(2)
Maximum Voltage on any input -0.3 to 6V
Output short circuit duration Indefinite
Power Dissipation (TA= 25°C)(3) 350mW
Storage Temperature Range −65°C to 150°C
Lead Temperature (soldering, 10sec) 260°C
Vapor Phase (60 sec) 215°C
Infrared (15sec) 220°C
ESD Susceptibility(4) Human Body Model 2kV
(1) Absolute Maximum Ratings indicate limits beyond which damage may occur to the device. Operating Ratings indicate conditions for
which the device is intended to be functional. For specifications, see Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) Without PCB copper enhancements. The maximum power dissipation must be de-rated at elevated temperatures and is limited by TJMAX
(maximum junction temperature), θJ-A (junction to ambient thermal resistance) and TA(ambient temperature). The maximum power
dissipation at any temperature is: PDissMAX = (TJMAX - TA) /θJ-A up to the value listed in the Absolute Maximum Ratings. θJ-A for SOT23-5
is 220°C/W, TJMAX = 125°C.
(4) The human body model is a 100 pF capacitor discharged through a 1.5 kΩresistor into each pin.
Operating Ratings
Maximum Input Supply Voltage 5.5V
Maximum Enable Input Voltage VIN
Maximum Load Current 20mA
Junction Temperature Range (TJ)−40°C to +125°C
2Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
Electrical Characteristics
LM4132-1.8 (VOUT = 1.8V)
Limits in standard type are for TJ= 25°C only, and limits in boldface type apply over the junction temperature (TJ) range of -
40°C to +125°C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes
only. Unless otherwise specified VIN = 5V and ILOAD = 0
Symbol Parameter Conditions Min Typ Max Unit
(1) (2) (1)
VREF Output Voltage Initial Accuracy
LM4132A-1.8 (A Grade - 0.05%) -0.05 0.05
LM4132B-1.8 (B Grade - 0.1%) -0.1 0.1
LM4132C-1.8 (C Grade - 0.2%) -0.2 0.2 %
LM4132D-1.8 (D Grade - 0.4%) -0.4 0.4
LM4132E-1.8 (E Grade - 0.5%) -0.5 0.5
TCVREF / °C Temperature Coefficient
(Note 6) LM4132A-1.8 0°C ≤TJ≤+ 85°C 10
-40°C ≤TJ≤+125°C 20
LM4132B-1.8 20 ppm / °C
LM4132C-1.8 20
-40°C ≤TJ≤+125°C
LM4132D-1.8 20
LM4132E-1.8 30
IQSupply Current 60 100 µA
IQ_SD Supply Current in Shutdown EN = 0V 3 7µA
ΔVREF/ΔVIN Line Regulation VREF + 400mV ≤VIN ≤5.5V 30 ppm / V
ΔVREF/ΔILOAD Load Regulation 0mA ≤ILOAD ≤20mA 25 120 ppm / mA
ΔVREF Long Term Stability(3) 1000 Hrs 50 ppm
Thermal Hysteresis(4) -40°C ≤TJ≤+125°C 75
VIN - VREF Dropout Voltage(5) ILOAD = 10mA 230 400 mV
VNOutput Noise Voltage 0.1 Hz to 10 Hz 170 µVPP
ISC Short Circuit Current 75 mA
VIL Enable Pin Maximum Low Input Level 35 %VIN
VIH Enable Pin Minimum High Input Level 65 %VIN
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
(2) Typical numbers are at 25°C and represent the most likely parametric norm.
(3) Long term stability is VREF @25°C measured during 1000 hrs.
(4) Thermal hysteresis is defined as the change in +25°C output voltage before and after cycling the device from (-40°C to 125°C).
(5) Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5V input.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: LM4132
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Electrical Characteristics
LM4132-2.0 (VOUT = 2.048V)
Limits in standard type are for TJ= 25°C only, and limits in boldface type apply over the junction temperature (TJ) range of -
40°C to +125°C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes
only. Unless otherwise specified VIN = 5V and ILOAD = 0
Symbol Parameter Conditions Min Typ Max Unit
(1) (2) (1)
VREF Output Voltage Initial Accuracy
LM4132A-2.0 (A Grade - 0.05%) -0.05 0.05
LM4132B-2.0 (B Grade - 0.1%) -0.1 0.1
LM4132C-2.0 (C Grade - 0.2%) -0.2 0.2 %
LM4132D-2.0 (D Grade - 0.4%) -0.4 0.4
LM4132E-2.0 (E Grade - 0.5%) -0.5 0.5
TCVREF / °C Temperature Coefficient
(Note 6) LM4132A-2.0 0°C ≤TJ≤+ 85°C 10
-40°C ≤TJ≤+125°C 20
LM4132B-2.0 20 ppm / °C
LM4132C-2.0 20
-40°C ≤TJ≤+125°C
LM4132D-2.0 20
LM4132E-2.0 30
IQSupply Current 60 100 µA
IQ_SD Supply Current in Shutdown EN = 0V 3 7µA
ΔVREF/ΔVIN Line Regulation VREF + 400mV ≤VIN ≤5.5V 30 ppm / V
ΔVREF/ΔILOAD Load Regulation 0mA ≤ILOAD ≤20mA 25 120 ppm / mA
ΔVREF Long Term Stability(3) 1000 Hrs 50 ppm
Thermal Hysteresis(4) -40°C ≤TJ≤+125°C 75
VIN - VREF Dropout Voltage(5) ILOAD = 10mA 175 400 mV
VNOutput Noise Voltage 0.1 Hz to 10 Hz 190 µVPP
ISC Short Circuit Current 75 mA
VIL Enable Pin Maximum Low Input Level 35 %VIN
VIH Enable Pin Minimum High Input Level 65 %VIN
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
(2) Typical numbers are at 25°C and represent the most likely parametric norm.
(3) Long term stability is VREF @25°C measured during 1000 hrs.
(4) Thermal hysteresis is defined as the change in +25°C output voltage before and after cycling the device from (-40°C to 125°C).
(5) Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5V input.
4Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
Electrical Characteristics
LM4132-2.5 (VOUT = 2.5V)
Limits in standard type are for TJ= 25°C only, and limits in boldface type apply over the junction temperature (TJ) range of -
40°C to +125°C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes
only. Unless otherwise specified VIN = 5V and ILOAD = 0
Symbol Parameter Conditions Min Typ Max Unit
(1) (2) (1)
VREF Output Voltage Initial Accuracy
LM4132A-2.5 (A Grade - 0.05%) -0.05 0.05
LM4132B-2.5 (B Grade - 0.1%) -0.1 0.1
LM4132C-2.5 (C Grade - 0.2%) -0.2 0.2 %
LM4132D-2.5 (D Grade - 0.4%) -0.4 0.4
LM4132E-2.5 (E Grade - 0.5%) -0.5 0.5
TCVREF / °C Temperature Coefficient
(Note 6) LM4132A-2.5 0°C ≤TJ≤+ 85°C 10
-40°C ≤TJ≤+125°C 20
LM4132B-2.5 20 ppm / °C
LM4132C-2.5 20
-40°C ≤TJ≤+125°C
LM4132D-2.5 20
LM4132E-2.5 30
IQSupply Current 60 100 µA
IQ_SD Supply Current in Shutdown EN = 0V 3 7µA
ΔVREF/ΔVIN Line Regulation VREF + 400mV ≤VIN ≤5.5V 50 ppm / V
ΔVREF/ΔILOAD Load Regulation 0mA ≤ILOAD ≤20mA 25 120 ppm / mA
ΔVREF Long Term Stability(3) 1000 Hrs 50 ppm
Thermal Hysteresis(4) -40°C ≤TJ≤+125°C 75
VIN - VREF Dropout Voltage(5) ILOAD = 10mA 175 400 mV
VNOutput Noise Voltage 0.1 Hz to 10 Hz 240 µVPP
ISC Short Circuit Current 75 mA
VIL Enable Pin Maximum Low Input Level 35 %VIN
VIH Enable Pin Minimum High Input Level 65 %VIN
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
(2) Typical numbers are at 25°C and represent the most likely parametric norm.
(3) Long term stability is VREF @25°C measured during 1000 hrs.
(4) Thermal hysteresis is defined as the change in +25°C output voltage before and after cycling the device from (-40°C to 125°C).
(5) Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5V input.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: LM4132
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Electrical Characteristics
LM4132-3.0 (VOUT = 3.0V)
Limits in standard type are for TJ= 25°C only, and limits in boldface type apply over the junction temperature (TJ) range of -
40°C to +125°C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes
only. Unless otherwise specified VIN = 5V and ILOAD = 0
Symbol Parameter Conditions Min Typ Max Unit
(1) (2) (1)
VREF Output Voltage Initial Accuracy
LM4132A-3.0 (A Grade - 0.05%) -0.05 0.05
LM4132B-3.0 (B Grade - 0.1%) -0.1 0.1
LM4132C-3.0 (C Grade - 0.2%) -0.2 0.2 %
LM4132D-3.0 (D Grade - 0.4%) -0.4 0.4
LM4132E-3.0 (E Grade - 0.5%) -0.5 0.5
TCVREF / °C Temperature Coefficient
(Note 6) LM4132A-3.0 0°C ≤TJ≤+ 85°C 10
-40°C ≤TJ≤+125°C 20
LM4132B-3.0 20 ppm / °C
LM4132C-3.0 20
-40°C ≤TJ≤+125°C
LM4132D-3.0 20
LM4132E-3.0 30
IQSupply Current 60 100 µA
IQ_SD Supply Current in Shutdown EN = 0V 3 7µA
ΔVREF/ΔVIN Line Regulation VREF + 400mV ≤VIN ≤5.5V 70 ppm / V
ΔVREF/ΔILOAD Load Regulation 0mA ≤ILOAD ≤20mA 25 120 ppm / mA
ΔVREF Long Term Stability(3) 1000 Hrs 50 ppm
Thermal Hysteresis(4) -40°C ≤TJ≤+125°C 75
VIN - VREF Dropout Voltage(5) ILOAD = 10mA 175 400 mV
VNOutput Noise Voltage 0.1 Hz to 10 Hz 285 µVPP
ISC Short Circuit Current 75 mA
VIL Enable Pin Maximum Low Input Level 35 %VIN
VIH Enable Pin Minimum High Input Level 65 %VIN
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
(2) Typical numbers are at 25°C and represent the most likely parametric norm.
(3) Long term stability is VREF @25°C measured during 1000 hrs.
(4) Thermal hysteresis is defined as the change in +25°C output voltage before and after cycling the device from (-40°C to 125°C).
(5) Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5V input.
6Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
Electrical Characteristics
LM4132-3.3 (VOUT = 3.3V)
Limits in standard type are for TJ= 25°C only, and limits in boldface type apply over the junction temperature (TJ) range of -
40°C to +125°C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes
only. Unless otherwise specified VIN = 5V and ILOAD = 0
Symbol Parameter Conditions Min Typ Max Unit
(1) (2) (1)
VREF Output Voltage Initial Accuracy
LM4132A-3.3 (A Grade - 0.05%) -0.05 0.05
LM4132B-3.3 (B Grade - 0.1%) -0.1 0.1
LM4132C-3.3 (C Grade - 0.2%) -0.2 0.2 %
LM4132D-3.3 (D Grade - 0.4%) -0.4 0.4
LM4132E-3.3 (E Grade - 0.5%) -0.5 0.5
TCVREF / °C Temperature Coefficient
(Note 6) LM4132A-3.3 0°C ≤TJ≤+ 85°C 10
-40°C ≤TJ≤+125°C 20
LM4132B-3.3 20 ppm / °C
LM4132C-3.3 20
-40°C ≤TJ≤+125°C
LM4132D-3.3 20
LM4132E-3.3 30
IQSupply Current 60 100 µA
IQ_SD Supply Current in Shutdown EN = 0V 3 7µA
ΔVREF/ΔVIN Line Regulation VREF + 400mV ≤VIN ≤5.5V 85 ppm / V
ΔVREF/ΔILOAD Load Regulation 0mA ≤ILOAD ≤20mA 25 120 ppm / mA
ΔVREF Long Term Stability(3) 1000 Hrs 50 ppm
Thermal Hysteresis(4) -40°C ≤TJ≤+125°C 75
VIN - VREF Dropout Voltage(5) ILOAD = 10mA 175 400 mV
VNOutput Noise Voltage 0.1 Hz to 10 Hz 310 µVPP
ISC Short Circuit Current 75 mA
VIL Enable Pin Maximum Low Input Level 35 %VIN
VIH Enable Pin Minimum High Input Level 65 %VIN
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
(2) Typical numbers are at 25°C and represent the most likely parametric norm.
(3) Long term stability is VREF @25°C measured during 1000 hrs.
(4) Thermal hysteresis is defined as the change in +25°C output voltage before and after cycling the device from (-40°C to 125°C).
(5) Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5V input.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: LM4132
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Electrical Characteristics
LM4132-4.1 (VOUT = 4.096V)
Limits in standard type are for TJ= 25°C only, and limits in boldface type apply over the junction temperature (TJ) range of -
40°C to +125°C unless otherwise specified. Minimum and Maximum limits are specified through test, design, or statistical
correlation. Typical values represent the most likely parametric norm at TJ= 25°C, and are provided for reference purposes
only. Unless otherwise specified VIN = 5V and ILOAD = 0
Symbol Parameter Conditions Min Typ Max Unit
(1) (2) (1)
VREF Output Voltage Initial Accuracy
LM4132A-4.1 (A Grade - 0.05%) -0.05 0.05
LM4132B-4.1 (B Grade - 0.1%) -0.1 0.1
LM4132C-4.1 (C Grade - 0.2%) -0.2 0.2 %
LM4132D-4.1 (D Grade - 0.4%) -0.4 0.4
LM4132E-4.1 (E Grade - 0.5%) -0.5 0.5
TCVREF / °C Temperature Coefficient
(Note 6) LM4132A-4.1 0°C ≤TJ≤+ 85°C 10
-40°C ≤TJ≤+125°C 20
LM4132B-4.1 20 ppm / °C
LM4132C-4.1 20
-40°C ≤TJ≤+125°C
LM4132D-4.1 20
LM4132E-4.1 30
IQSupply Current 60 100 µA
IQ_SD Supply Current in Shutdown EN = 0V 3 7µA
ΔVREF/ΔVIN Line Regulation VREF + 400mV ≤VIN ≤5.5V 100 ppm / V
ΔVREF/ΔILOAD Load Regulation 0mA ≤ILOAD ≤20mA 25 120 ppm / mA
ΔVREF Long Term Stability(3) 1000 Hrs 50 ppm
Thermal Hysteresis(4) -40°C ≤TJ≤+125°C 75
VIN - VREF Dropout Voltage(5) ILOAD = 10mA 175 400 mV
VNOutput Noise Voltage 0.1 Hz to 10 Hz 350 µVPP
ISC Short Circuit Current 75 mA
VIL Enable Pin Maximum Low Input Level 35 %VIN
VIH Enable Pin Minimum High Input Level 65 %VIN
(1) Limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation using
Statistical Quality Control.
(2) Typical numbers are at 25°C and represent the most likely parametric norm.
(3) Long term stability is VREF @25°C measured during 1000 hrs.
(4) Thermal hysteresis is defined as the change in +25°C output voltage before and after cycling the device from (-40°C to 125°C).
(5) Dropout voltage is defined as the minimum input to output differential at which the output voltage drops by 0.5% below the value
measured with a 5V input.
8Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
10 100 1k 10k
FREQUENCY (Hz)
0
2
4
6
8
10
12
14
16
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
NO COUT
-90
0
POWER SUPPLY REJECTION (dB)
10 100 1k 10k 100k
FREQUENCY (Hz) 1M
-80
-70
-60
-50
-40
-30
-20
-10
NO COUT
COUT = 0.1 PF
2.2 2.7 3.2 3.7 4.2 4.7 5.2
OUTPUT VOLTAGE (V)
1.7990
1.7985
1.7990
1.7995
1.8000
1.8005
1.8010
1.8015
1.8020
125oC
25oC
-40oC
INPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
0 2 4 6 8 10 12 14 16 18 20
LOAD CURRENT (mA)
1.7980
1.7985
1.7990
1.7995
1.8000
1.8005
1.8010
125oC
25oC
-40oC
TEMPERATURE (oC)
OUTPUT VOLTAGE (V)
-40 -20 0 20 40 60 80 100 120
1.797
1.798
1.799
1.800
1.801
1.802
1.803
1.804
1.796
5 TYPICAL UNITS
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
Typical Performance Characteristics for 1.8V
Output Voltage
vs
Temperature Load Regulation
Figure 1. Figure 2.
Line Regulation 0.1-10Hz Noise
Figure 3. Figure 4.
Power Supply Rejection
vs
Output Voltage Noise Spectrum Frequency
Figure 5. Figure 6.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: LM4132
10 100 1k 10k
FREQUENCY (Hz)
0
2
4
6
8
10
12
14
16
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
NO COUT
-80
-70
-60
-50
-40
0
POWER SUPPLY REJECTION (dB)
10 100 1k 10k 100k
FREQUENCY (Hz)
-30
-20
-10
1M
NO COUT
COUT = 0.1 PF
2.5 3.0 3.5 4.0 4.5 5.0 5.5
INPUT VOLTAGE (V)
2.046
2.047
2.048
2.049
2.050
2.051
2.052
OUTPUT VOLTAGE (V)
125oC
25oC
-40oC
-50 -25 0 25 50 75 100 125
TEMPERATURE (oC)
2.045
2.046
2.047
2.048
2.049
2.050
2.051
2.052
OUTPUT VOLTAGE (V)
5 TYPICAL UNITS
0 4 8 12 16 20
2.045
2.046
2.047
2.048
2.049
2.050
OUTPUT VOLTAGE (V)
LOAD CURRENT (mA)
125oC
25oC
-40oC
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics for 2.048V
Output Voltage
vs
Temperature Load Regulation
Figure 7. Figure 8.
Line Regulation 0.1 - 10 Hz Noise
Figure 9. Figure 10.
Power Supply Rejection
vs
Output Voltage Noise Spectrum Frequency
Figure 11. Figure 12.
10 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
10 100 1k 10k
FREQUENCY (Hz)
0
4
8
12
16
20
24
28
32
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
NO COUT
-80
-70
-60
-50
-40
0
POWER SUPPLY REJECTION (dB)
10 100 1k 10k 100k
FREQUENCY (Hz)
-30
-20
-10
1M
NO COUT
COUT = 0.1 PF
3.0 3.5 4.0 4.5 5.0 5.5
2.497
2.498
2.499
2.500
2.501
2.502
OUTPUT VOLTAGE (V)
INPUT VOLTAGE (V)
125oC
25oC
-40oC
-50 -25 0 25 50 75 100 125
TEMPERATURE (oC)
2.497
2.498
2.499
2.500
2.501
2.502
2.503
2.504
OUTPUT VOLTAGE (V)
5 TYPICAL UNITS
0 4 8 12 16 20
2.498
2.499
2.500
2.501
2.502
2.503
OUTPUT VOLTAGE (V)
LOAD CURRENT (mA)
125oC
25oC
-40oC
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
Typical Performance Characteristics for 2.5V
Output Voltage
vs
Temperature Load Regulation
Figure 13. Figure 14.
Line Regulation 0.1 - 10 Hz Noise
Figure 15. Figure 16.
Power Supply Rejection
vs
Output Voltage Noise Spectrum Frequency
Figure 17. Figure 18.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: LM4132
-80
-70
-60
-50
-40
0
POWER SUPPLY REJECTION (dB)
10 100 1k 10k 100k
FREQUENCY (Hz)
-30
-20
-10
1M
NO COUT
COUT = 0.1 PF
OUTPUT NOISE VOLTAGE PV(Hz))
10 100 1k 10k
FREQUENCY (Hz)
0
30
5
10
15
20
25 NO COUT
3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
INPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
2.9980
2.9985
2.9990
2.9995
3.0000
3.0005
3.0010
3.0015
3.0020
125oC
25oC
-40oC
0 2 4 6 8 10 12 14 16 18 20
LOAD CURRENT (mA)
125oC
25oC
-40oC
OUTPUT VOLTAGE (V)
2.9975
2.9980
2.9985
2.9990
2.9995
3.0000
3.0005
3.0010
3.0015
3.0020
TEMPERATURE (oC)
-40 -20 0 20 40 60 80 100 120
2.996
2.997
2.998
2.999
3
3.001
3.002
3.003
3.004
3.005
3.006
OUTPUT VOLTAGE (V)
5 TYPICAL UNITS
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics for 3.0V
Output Voltage
vs
Temperature Load Regulation
Figure 19. Figure 20.
Line Regulation 0.1-10 Hz Noise
Figure 21. Figure 22.
Power Supply Rejection
vs
Output Voltage Noise Spectrum Frequency
Figure 23. Figure 24.
12 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
OUTPUT NOISE VOLTAGE PV(Hz))
10 100 1k 10k
FREQUENCY (Hz)
0
30
5
10
15
20
25 NO COUT
-90
0
POWER SUPPLY REJECTION (dB)
10 100 1k 10k 100k
FREQUENCY (Hz) 1M
-80
-70
-60
-50
-40
-30
-20
-10 NO COUT
COUT = 0.1 PF
3.5 3.7 3.9 4.1 4.3 4.5 4.7 4.9 5.1 5.3 5.5
INPUT VOLTAGE (V)
OUTPUT VOLTAGE (V)
3.2996
3.2998
3.3000
3.3002
3.3004
3.3006
3.3008
3.3010
125oC
25oC
-40oC
OUTPUT VOLTAGE (V)
0 2 4 6 8 10 12 14 16 18 20
LOAD CURRENT (mA)
3.2975
3.2980
3.2985
3.2990
3.2995
3.3000
3.3005
125oC
25oC
-40oC
TEMPERATURE (oC)
-40 -20 0 20 40 60 80 100 120
3.295
3.296
3.297
3.298
3.299
3.3
3.301
3.302
3.303
3.304
3.305
OUTPUT VOLTAGE (V)
5 TYPICAL UNITS
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
Typical Performance Characteristics for 3.3V
Output Voltage
vs
Temperature Load Regulation
Figure 25. Figure 26.
Line Regulation 0.1-10 Hz Noise
Figure 27. Figure 28.
Power Supply Rejection
vs
Output Voltage Noise Spectrum Frequency
Figure 29. Figure 30.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: LM4132
10 100 1k 10k
FREQUENCY (Hz)
0
4
8
12
16
20
24
28
32
OUTPUT NOISE VOLTAGE (PV/rt(Hz))
NO COUT
-80
-70
-60
-50
-40
0
POWER SUPPLY REJECTION RATIO (dB)
10 100 1k 10k 100k
FREQUENCY (Hz)
-30
-20
-10
1M
NO COUT
COUT = 0.1 PF
4.5 4.7 4.9 5.1 5.3 5.5
4.092
4.093
4.094
4.095
4.096
4.097
4.098
4.099
4.100
OUTPUT VOLTAGE (V)
INPUT VOLTAGE (V)
125oC
25oC
-40oC
-50 -25 0 25 50 75 100 125
TEMPERATURE (oC)
4.090
4.092
4.094
4.096
4.098
4.100
4.102
4.104
OUTPUT VOLTAGE (V)
5 TYPICAL UNITS
0 4 8 12 16 20
4.093
4.094
4.095
4.096
4.097
4.098
OUTPUT VOLTAGE (V)
LOAD CURRENT (mA)
125oC
25oC
-40oC
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics for 4.096V
Output Voltage
vs
Temperature Load Regulation
Figure 31. Figure 32.
Line Regulation 0.1 - 10 Hz Noise
Figure 33. Figure 34.
Power Supply Rejection
vs
Output Voltage Noise Spectrum Frequency
Figure 35. Figure 36.
14 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
0 5 10 15 20
LOAD CURRENT (mA)
GROUND CURRENT (PA)
60
65
70
75
80
85
55
0 100 200 300 400 500 600 700 800 9001000
DRIFT (ppm)
150
TIME (Hours)
-200
200
-150
-100
-50
0
50
100
150 1 TYPICAL UNIT FROM EACH
VOLTAGE OPTION
2 2.5 3 3.5 4 4.5 5
VIN (V)
0
0.5
1
1.5
2
2.5
3
VEN (V)
VIL
VIH
2.0
2.5
3.0
3.5
4.0
4.5
5.0
IQ SHUTDOWN (PA)
-40 -25 0 25 50 75 100 125
TEMPERATURE (oC)
0.5 1.5 2.5 3.5 4.5 5.5
0
20
40
60
80
100
SUPPLY CURRENT (PA)
INPUT VOLTAGE (V)
VREF = 2.048V
125oC
25oC
-40oC
VDROPOUT (mV)
2.048V
4.096V
2 7 12 17 22
ILOAD (mA)
0
50
100
150
200
250
300
350
400
450
2.5V
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
Typical Performance Characteristics
Dropout Supply Current
vs vs
Load to 0.5% Accuracy Input Voltage
Figure 37. Figure 38.
Shutdown IQ
vs
Enable Threshold Voltage and Hysteresis Temperature
Figure 39. Figure 40.
Ground Current
vs
Typical Long Term Stability Load Current
Figure 41. Figure 42.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: LM4132
HYSTERESIS (ppm)
FREQUENCY
0 25 50 75 100 125 150 200
0
5
10
15
20
25
30
35
40
45
Temperature Range
-40oC < TJ < 125oC
after 8 thermal cycles
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Typical Performance Characteristics (continued)
Typical Thermal Hysteresis Turn-On Transient Response
Figure 43. Figure 44.
Load Transient Response Line Transient Response
ILOAD = 0 to 10mA VIN = 4V to 5.5V
Figure 45. Figure 46.
16 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
APPLICATION INFORMATION
THEORY OF OPERATION
The foundation of any voltage reference is the band-gap circuit. While the reference in the LM4132 is developed
from the gate-source voltage of transistors in the IC, principles of the band-gap circuit are easily understood
using a bipolar example. For a detailed analysis of the bipolar band-gap circuit, please refer to Application Note
AN-56.
SUPPLY AND ENABLE VOLTAGES
To ensure proper operation, VEN and VIN must be within a specified range. An acceptable range of input voltages
is:
VIN > VREF + 400mV (ILOAD ≤10mA) (1)
The enable pin uses an internal pull-up current source (IPULL_UP ≊2µA) that may be left floating or triggered by an
external source. If the part is not enabled by an external source, it may be connected to VIN. An acceptable range
of enable voltages is given by the enable transfer characteristics. See the Electrical Characteristics section and
Enable Transfer Characteristics figure for more detail. Note, the part will not operate correctly for VEN > VIN.
COMPONENT SELECTION
A small ceramic (X5R or X7R) capacitor on the input must be used to ensure stable operation. The value of CIN
must be sized according to the output capacitor value. The value of CIN must satisfy the relationship CIN ≥COUT.
When no output capacitor is used, CIN must have a minimum value of 0.1µF. Noise on the power-supply input
may affect the output noise. Larger input capacitor values (typically 4.7µF to 22µF) may help reduce noise on the
output and significantly reduce overshoot during startup. Use of an additional optional bypass capacitor between
the input and ground may help further reduce noise on the output. With an input capacitor, the LM4132 will drive
any combination of resistance and capacitance up to VREF/20mA and 10µF respectively.
The LM4132 is designed to operate with or without an output capacitor and is stable with capacitive loads up to
10µF. Connecting a capacitor between the output and ground will significantly improve the load transient
response when switching from a light load to a heavy load. The output capacitor should not be made arbitrarily
large because it will effect the turn-on time as well as line and load transients.
While a variety of capacitor chemistry types may be used, it is typically advisable to use low esr ceramic
capacitors. Such capacitors provide a low impedance to high frequency signals, effectively bypassing them to
ground. Bypass capacitors should be mounted close to the part. Mounting bypass capacitors close to the part will
help reduce the parasitic trace components thereby improving performance.
SHORT CIRCUITED OUTPUT
The LM4132 features indefinite short circuit protection. This protection limits the output current to 75mA when the
output is shorted to ground.
TURN ON TIME
Turn on time is defined as the time taken for the output voltage to rise to 90% of the preset value. The turn on
time depends on the load. The turn on time is typically 33.2µs when driving a 1µF load and 78.8µs when driving
a 10µF load. Some users may experience an extended turn on time (up to 10ms) under brown out conditions
and low temperatures (-40°C).
THERMAL HYSTERESIS
Thermal hysteresis is defined as the change in output voltage at 25ºC after some deviation from 25ºC. This is to
say that thermal hysteresis is the difference in output voltage between two points in a given temperature profile.
An illustrative temperature profile is shown in Figure 47.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: LM4132
TD = VREF x 'Tx 106 ppm
(VREF_MAX - VREF_MIN)
Temperature Range
Voltage
Temperature
VREF_MAX
Change in Output Voltage
VREF_MIN
VHYS = lVREF1 - VREF2l
VREF x 106 ppm
-40oC
VREF1 Time
VREF2
25oC
125oC
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Figure 47. Illustrative Temperature Profile
This may be expressed analytically as the following:
Where
• VHYS = Thermal hysteresis expressed in ppm
• VREF = Nominal preset output voltage
• VREF1 = VREF before temperature fluctuation
• VREF2 = VREF after temperature fluctuation.
• The LM4132 features a low thermal hysteresis of 75 ppm (typical) from -40°C to 125°C after 8 temperature
cycles. (2)
TEMPERATURE COEFFICIENT
Temperature drift is defined as the maximum deviation in output voltage over the operating temperature range.
This deviation over temperature may be illustrated as shown in Figure 48.
Figure 48. Illustrative VREF vs Temperature Profile
Temperature coefficient may be expressed analytically as the following:
(3)
TD= Temperature drift
VREF = Nominal preset output voltage
VREF_MIN = Minimum output voltage over operating temperature range
VREF_MAX = Maximum output voltage over operating temperature range
ΔT = Operating temperature range.
The LM4132 features a low temperature drift of 10ppm (max) to 30ppm (max), depending on the grade.
18 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
x 0.1
VREF = Percent_Error
VERROR
x 103
VREF = ppmERROR
VERROR
x 103
VREF
2n= VERROR
= VERROR
103
VREF x ppmERROR
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
LONG TERM STABILITY
Long-term stability refers to the fluctuation in output voltage over a long period of time (1000 hours). The LM4132
features a typical long-term stability of 50ppm over 1000 hours. The measurements are made using 5 units of
each voltage option, at a nominal input voltage (5V), with no load, at room temperature.
EXPRESSION OF ELECTRICAL CHARACTERISTICS
Electrical characteristics are typically expressed in mV, ppm, or a percentage of the nominal value. Depending
on the application, one expression may be more useful than the other. To convert one quantity to the other one
may apply the following:
ppm to mV error in output voltage:
Where
• VREF is in volts (V) and VERROR is in milli-volts (mV). (4)
Bit error (1 bit) to voltage error (mV):
(5)
VREF is in volts (V), VERROR is in milli-volts (mV), and n is the number of bits.
mV to ppm error in output voltage:
Where
• VREF is in volts (V) and VERROR is in milli-volts (mV). (6)
Voltage error (mV) to percentage error (percent):
Where
• VREF is in volts (V) and VERROR is in milli-volts (mV). (7)
PRINTED CIRCUIT BOARD and LAYOUT CONSIDERATIONS
References in SOT packages are generally less prone to PC board mounting than devices in Small Outline
(SOIC) packages. To minimize the mechanical stress due to PC board mounting that can cause the output
voltage to shift from its initial value, mount the reference on a low flex area of the PC board, such as near the
edge or a corner.
The part may be isolated mechanically by cutting a U shape slot on the PCB for mounting the device. This
approach also provides some thermal isolation from the rest of the circuit.
Bypass capacitors must be mounted close to the part. Mounting bypass capacitors close to the part will reduce
the parasitic trace components thereby improving performance.
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: LM4132
LM4132
VIN
EN GND
VREF
Input
Enable
Output
CIN R1
500:
RSET
1 k:
IOUT
RL
0.1µF
IGND
IOUT = (VREF/(R1 + RSET)) + IGND
LM4132
VIN
EN GND
VREF
Input
Enable
+5V
100 k:
0.1µF
V
V
REF_FORCE
REF_SENSE
CIN
LM4132
VIN
EN GND
VREF
Input
Enable
VREF
CIN COUT RR
R/2
-VREF
+5V
-5V
4.7µF < COUT < 10 µF
LM4132
SNVS372C –AUGUST 2005–REVISED APRIL 2013
www.ti.com
Typical Application Circuits
Figure 49. Voltage Reference with Complimentary Output
Figure 50. Precision Voltage Reference with Force and Sense Output
Figure 51. Programmable Current Source
20 Submit Documentation Feedback Copyright © 2005–2013, Texas Instruments Incorporated
Product Folder Links: LM4132
LM4132
www.ti.com
SNVS372C –AUGUST 2005–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision B (April 2013) to Revision C Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 20
Copyright © 2005–2013, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: LM4132
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM4132AMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AA
LM4132AMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BA
LM4132AMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CA
LM4132AMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DA
LM4132AMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EA
LM4132AMF-4.1 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 R4FA
LM4132AMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FA
LM4132AMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AA
LM4132AMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BA
LM4132AMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CA
LM4132AMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DA
LM4132AMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EA
LM4132AMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FA
LM4132BMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AB
LM4132BMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BB
LM4132BMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CB
LM4132BMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DB
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 2
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM4132BMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EB
LM4132BMF-4.1 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 R4FB
LM4132BMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FB
LM4132BMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AB
LM4132BMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BB
LM4132BMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CB
LM4132BMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DB
LM4132BMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EB
LM4132BMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FB
LM4132CMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AC
LM4132CMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BC
LM4132CMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CC
LM4132CMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DC
LM4132CMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EC
LM4132CMF-4.1 NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 R4FC
LM4132CMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FC
LM4132CMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AC
LM4132CMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BC
LM4132CMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CC
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 3
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM4132CMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DC
LM4132CMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EC
LM4132CMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FC
LM4132DMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AD
LM4132DMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BD
LM4132DMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CD
LM4132DMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DD
LM4132DMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4ED
LM4132DMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FD
LM4132DMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AD
LM4132DMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BD
LM4132DMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CD
LM4132DMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DD
LM4132DMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4ED
LM4132DMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FD
LM4132EMF-1.8/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AE
LM4132EMF-2.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BE
LM4132EMF-2.5/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CE
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 4
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead/Ball Finish
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
LM4132EMF-3.0/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DE
LM4132EMF-3.3/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EE
LM4132EMF-4.1/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FE
LM4132EMFX-1.8/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4AE
LM4132EMFX-2.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4BE
LM4132EMFX-2.5/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4CE
LM4132EMFX-3.0/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4DE
LM4132EMFX-3.3/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4EE
LM4132EMFX-4.1/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS
& no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 R4FE
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
PACKAGE OPTION ADDENDUM
www.ti.com 1-Nov-2013
Addendum-Page 5
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM4132AMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMF-4.1 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132AMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 1
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM4132BMF-4.1 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132BMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMF-4.1 SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132CMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132DMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMF-1.8/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMF-2.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMF-2.5/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMF-3.0/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMF-3.3/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMF-4.1/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMFX-1.8/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMFX-2.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMFX-2.5/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMFX-3.0/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 2
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
LM4132EMFX-3.3/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
LM4132EMFX-4.1/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4132AMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132AMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132AMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132AMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132AMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132AMF-4.1 SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132AMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132AMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132AMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132AMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132AMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132AMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132AMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132BMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132BMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 3
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4132BMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132BMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132BMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132BMF-4.1 SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132BMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132BMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132BMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132BMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132BMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132BMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132BMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132CMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132CMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132CMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132CMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132CMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132CMF-4.1 SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132CMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132CMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132CMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132CMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132CMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132CMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132CMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132DMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132DMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132DMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132DMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132DMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132DMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132DMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132DMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132DMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132DMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132DMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132DMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132EMF-1.8/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132EMF-2.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132EMF-2.5/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132EMF-3.0/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132EMF-3.3/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132EMF-4.1/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0
LM4132EMFX-1.8/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132EMFX-2.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 4
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
LM4132EMFX-2.5/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132EMFX-3.0/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132EMFX-3.3/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
LM4132EMFX-4.1/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0
PACKAGE MATERIALS INFORMATION
www.ti.com 23-Sep-2013
Pack Materials-Page 5
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products Applications
Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive
Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications
Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers
DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps
DSP dsp.ti.com Energy and Lighting www.ti.com/energy
Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial
Interface interface.ti.com Medical www.ti.com/medical
Logic logic.ti.com Security www.ti.com/security
Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense
Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video
RFID www.ti-rfid.com
OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com
Wireless Connectivity www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
