RClamp0504FA RailClamp(R) Low Capacitance TVS Array PROTECTION PRODUCTS - RailClamp(R) Description Features Transient protection for high-speed data lines to RailClamp(R) low capacitance TVS array designed to protect high speed data interfaces. This series has been specifically designed to protect sensitive components which are connected to data and transmission lines from overvoltage caused by ESD (electrostatic discharge), CDE (Cable Discharge Events), and EFT (electrical fast transients). The unique design incorporates surge rated, low capacitance steering diodes and a TVS diode in a single package. This allows the device to absorb large amounts of energy while protecting downstream components from harmful transient events. The RClamp(R)0504FA is in a 6-pin, SC-70 package. The leads are finished with lead-free matte tin. They may be used to meet the ESD immunity requirements of IEC 61000-4-2, Level 4 (15kV air, 8kV contact discharge). The combination of small size, low capacitance, and high ESD surge capability makes them ideal for use in applications such as USB 2.0, multimedia card, and video interfaces. Mechanical Characteristics EIAJ SC-70 6L package Lead Finish: Matte Tin Pb-Free, Halogen Free, RoHS/WEEE Compliant Molding compound flammability rating: UL 94V-0 Packaging : Tape and Reel Applications Circuit Diagram USB 2.0 USB OTG Monitors and Flat Panel Displays Digital Visual Interface (DVI) SIM Ports IEEE 1394 Firewire Ports Schematic & PIN Configuration 5 1 IEC 61000-4-2 (ESD) 15kV (air), 8kV (contact) IEC 61000-4-4 (EFT) 40A (5/50ns) Array of surge rated diodes with internal TVS Diode Small package (2.4 x 2.2mm) saves board space Protects up to four I/O lines & power line Low capacitance (<3pF) for high-speed interfaces No insertion loss to 2.0GHz Low leakage current and clamping voltage Low operating voltage: 5.0V Solid-state silicon-avalanche technology 3 4 6 1 6 2 5 3 4 2 SC-70 6L (Top View) Revision 4/15/2010 1 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Absolute Maximum Rating R ating Symbol Value Units Peak Pulse Power (tp = 8/20s) Pp k 150 Watts Peak Pulse Current (tp = 8/20s) IP P 6 A ESD p er IEC 61000-4-2 (Air) ESD p er IEC 61000-4-2 (Contact) VESD 15 8 kV TJ -55 to +125 C TSTG -55 to +150 C Op erating Temp erature Storage Temp erature Electrical Characteristics (T=25oC) Parameter Symbol Conditions Minimum Typical Maximum Units Reverse Stand-Off Voltage VRWM Pi n 5 to 2 5 V Reverse Breakdown Voltage V BR It = 1mA Pi n 5 to 2 Reverse Leakage Current IR VRWM = 5V, T=25C Pi n 5 to 2 3 A Clamp ing Voltage VC IPP = 1A, tp = 8/20s A n y p i n to p i n 2 15 V Clamp ing Voltage VC IPP = 6A, tp = 8/20s A n y p i n to p i n 2 25 V Junction Cap acitance Cj VR = 0V, f = 1MHz Any I/O p in to p in 2 3 pF VR = 0V, f = 1MHz Between I/O p ins 1.5 pF 6 V Note 1: I/O pins are pin 1, 3, 4, and 6 (c) 2010 Semtech Corp. 2 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Typical Characteristics Non-Repetitive Peak Pulse Power vs. Pulse Time Power Derating Curve 10 110 90 % of Rated Power or PI P Peak Pulse Power - PPP (kW) 100 1 0.1 80 70 60 50 40 30 20 10 0 0.01 0.1 1 10 100 0 1000 25 50 Pulse Duration - tp (s) Pulse Waveform 80 PP Percent of I Clamping Voltage - VC (V) 90 e -t 50 40 125 150 25 Waveform Parameters: tr = 8s td = 20s 100 60 100 Clamping Voltage vs. Peak Pulse Current 110 70 75 Ambient Temperature - TA (oC) td = IPP/2 30 20 Waveform Parameters: tr = 8s td = 20s 20 Pin 1, 3, 4, or 6 to pin 2 15 Pin 5 to pin 2 10 10 0 0 5 10 15 20 25 5 30 0 1 Time (s) Forward Voltage vs. peak Pulse Current 2 3 4 Peak Pulse Current - IPP (A) 5 6 Capacitance vs. Reverse Voltage (Normalized to 0V) 2 8 f = 1MHz Normalized Capacitance Forward Voltage - V F (V) 7 6 5 4 3 Waveform Parameters: tr = 8s td = 20s 2 1 1.5 Any I/O Pin to Pin 2 1 0.5 0 0 1 2 3 4 5 0 6 0 Peak Pulse Current - IPP (A) (c) 2010 Semtech Corp. 1 2 3 4 5 Reverse Voltage - VR (V) 3 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Typical Characteristics Insertion Loss S21 (I/O to Pin 2) CH1 S21 LOG Insertion Loss S21 (I/O to I/O) 6 dB / REF 0 dB CH1 S21 STOP 3000. 000000 MHz START . 030 MHz LOG START . 030 MHz 6 dB / REF 0 dB START. 030 MHz Analog Crosstalk CH1 S21 LOG STOP 3000. 000000 MHz ESD Response (8kV Contact per IEC 61000-4-2) 20 dB/REF 0 dB STOP 3000. 000000 MHz Note: Data is taken with a 10x attenuator (c) 2010 Semtech Corp. 4 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Applications Information Protection of Four Data Lines and Power Supply Line Device Connection Options for Protection of Four High-Speed Data Lines This device is designed to protect data lines by clamping them to a fixed reference. When the voltage on the protected line exceeds the reference voltage the steering diodes are forward biased, conducting the transient current away from the sensitive circuitry. Data lines are connected at pins 1, 3, 4 and 6. Pin 2 should be connected directly to a ground plane. The path length is kept as short as possible to minimize parasitic inductance. The positive reference is connected at pin 5. The options for connecting the positive reference are as follows: Protection of Four Data Lines Using Internal TVS Diode as Reference 1. To protect data lines and the power line, connect pin 5 directly to the positive supply rail (VCC). In this configuration the data lines are referenced to the supply voltage. The internal TVS diode prevents over-voltage on the supply rail. 2. In applications where the supply rail does not exit the system, the internal TVS may be used as the reference. In this case, pin 5 is not connected. The steering diodes will begin to conduct when the voltage on the protected line exceeds the working voltage of the TVS (plus one diode drop). 3. In applications where complete supply isolation is desired, the internal TVS is again used as the reference and VCC is connected to one of the I/O inputs. An example of this configuration is the protection of a SIM port. The Clock, Reset, I/O, and VCC lines are connected at pins 1, 3, 4, and 6. Pin 2 is connected to ground and pin 5 is not connected. Matte Tin Lead Finish Matte tin has become the industry standard lead-free replacement for SnPb lead finishes. A matte tin finish is composed of 100% tin solder with large grains. Since the solder volume on the leads is small compared to the solder paste volume that is placed on the land pattern of the PCB, the reflow profile will be determined by the requirements of the solder paste. Therefore, these devices are compatible with both lead-free and SnPb assembly techniques. In addition, unlike other lead-free compositions, matte tin does not have any added alloys that can cause degradation of the solder joint. (c) 2010 Semtech Corp. 5 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Typical Applications SIM Port - Protection of Three Data Lines and VCC USB OTG Receptable Carkit VBus DD+ ID GND To Phone Mini B Receptable Shield Gnd 1 6 2 5 3 4 Mini A Receptable USB OTG Carkit Protection (c) 2010 Semtech Corp. 6 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Typical Applications SD12 RClamp0504FA IEEE 1394 Firewire Protection (c) 2010 Semtech Corp. 7 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Outline Drawing - SC70-6L A DIM D e1 A A1 A2 b c D E1 E e e1 L L1 N 01 aaa bbb ccc N E/2 E E1 ccc C 2X N/2 TIPS 1 2 e B D aaa C A2 DIMENSIONS INCHES MILLIMETERS MIN NOM MAX MIN NOM MAX .043 .004 .000 .028 .035 .039 .006 .012 .009 .003 .071 .079 .087 .045 .049 .053 .083 BSC .026 BSC .051 .010 .014 .018 (.017) 6 8 0 .004 .004 .012 1.10 0.00 0.10 0.70 0.90 1.00 0.15 0.30 0.08 0.22 1.80 2.00 2.20 1.15 1.25 1.35 2.10 BSC 0.65 BSC 1.30 BSC 0.26 0.36 0.46 (0.42) 6 0 8 0.10 0.10 0.30 A SEATING PLANE H A1 C bxN bbb C A-B D c GAGE PLANE 0.15 L 01 (L1) DETAIL SEE DETAIL SIDE VIEW A A NOTES: 1. CONTROLLING DIMENSIONS ARE IN MILLIMETERS (ANGLES IN DEGREES). 2. DATUMS -A- AND -B- TO BE DETERMINED AT DATUM PLANE -H3. DIMENSIONS "E1" AND "D" DO NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. 4. REFERENCE JEDEC STD MO-203, VARIATION AB. Land Pattern - SC70-6L X DIM C G C G P X Y Z Z Y DIMENSIONS INCHES MILLIMETERS (.073) .039 .026 .016 .033 .106 (1.85) 1.00 0.65 0.40 0.85 2.70 P NOTES: 1. (c) 2010 Semtech Corp. THIS LAND PATTERN IS FOR REFERENCE PURPOSES ONLY. CONSULT YOUR MANUFACTURING GROUP TO ENSURE YOUR COMPANY'S MANUFACTURING GUIDELINES ARE MET. 8 www.semtech.com RClamp0504FA PROTECTION PRODUCTS Marking Ordering Information 0504F YYWW Part Number Qty per Reel Reel Size RClamp 0504FATCT 3,000 7 Inch RailClamp and RClamp are trademarks of Semtech Corporation Note: YYWW = Date Code Tape and Reel Specification 0504F YYWW 0504F 0504F 0504F 0504F 0504F 0504F 0504F YYWW YYWW YYWW YYWW YYWW YYWW YYWW Device Orientation in Tape A0 2.40 +/-0.15 mm B0 K0 2.40 +/-0.15 mm Tape Width B, (Max) D 8 mm 4.2 mm 1.5 + 0.1 mm - 0.0 mm ) 1.20 +/-0.15 mm D1 E 0.5 mm 0.05 1.750.10 mm F K (MAX) P P0 P2 T(MAX) 3.50.05 mm 2.4 mm 4.00.1 mm 4.00.1 mm 2.00.05 mm 0.4 mm W 8.0 mm + 0.3 mm - 0.1 mm Contact Information Semtech Corporation Protection Products Division 200 Flynn Rd., Camarillo, CA 93012 Phone: (805)498-2111 FAX (805)498-3804 (c) 2010 Semtech Corp. 9 www.semtech.com