2N3585+JANTX - MICROSEMI - Datasheet.Live

P300 2.5-Inch SATA NAND Flash SSD

MTFDDACxxxSAL1x1

Features

• Micron® SLC NAND Flash

• RoHS-compliant package

• SATA 6 Gb/s interface

• ATA modes supported

– PIO modes 3 and 4

– Multiword DMA modes 0, 1, 2

– Ultra DMA modes 0, 1, 2, 3, 4, 5, 6

• Industry-standard, 512-byte sector size support

• Hot-plug capable

• Native command queueing support with 32 com-

mand slot support

• ATA8-ACS2 command set support

• Secure erase (data page) command set

• Self-monitoring, analysis, and reporting technology

(SMART) command set

• Performance (empty/steady state)1, 2, 3, 4

– Sequential READ: up to 360/360 MB/s

– Sequential WRITE: up to 275/255 MB/s

– Random READ: up to 60,000/44,000 IOPs

– Random WRITE: up to 45,200/16,000 IOPs

– READ latency: 0.153/0.154ms (TYP)

– WRITE latency: 0.118/0.424ms (TYP)

• Reliability

– MTBF: 2 million hours

– 3-year warranty

– Static and dynamic wear leveling

– Field-upgradable firmware

– Uncorrectable bit error rate (UBER): <1 sector

per 1016 bits read

– Low power consumption: <7W (AVG)

• Endurance: Total bytes written (TBW) – 50GB

( 0.875PB); 100GB (1.75PB); 200GB (3.5PB)

• Mechanical/electrical

– Standard SATA connector

– 5V power (±10%)

– Dimensions: 100.45mm x 69.85mm x 9.5mm

– Weight: 100g

• Operating temperature: 0°C to 70°C

• Humidity (operating): 5% to 95% RH

• Shock and vibration

– 1500G/0.5ms

– 5–500Hz at 3.1G

• Capacity5: 50GB, 100GB, 200GB

Notes: 1. 128K transfers used for sequential READ/

WRITE values.

2. 4K transfers used for random READ/WRITE

latency values.

3. I/O performance numbers as measured us-

ing Iometer with a queue depth of 32 and

write cache disabled.

4. Performance values apply to all drive ca-

pacities.

5. 1GB = 1 billion bytes; formatted capacity is

less.

Warranty: Contact your Micron sales representative

for further information regarding the product,

including product warranties.

P300 2.5-Inch NAND Flash SSD

Features

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 1Micron Technology, Inc. reserves the right to change products or specifications without notice.

Products and specifications discussed herein are subject to change by Micron without notice.

Part Numbering Information

The Micron® P300 SSD is available in different configurations and densities. Visit www.micron.com for a list of val-

id part numbers.

Figure 1: Part Number Chart

MT FD D AC xxx S AL - 1 N 1 ES

Micron Technology

Product Family

FD = Flash drive

Drive Interface

D = SATA 6.0 Gb/s

Drive Form Factor

AC = 2.5-inch (9.5mm high)

Drive Density

050 = 50GB

100 = 100GB

200 = 200GB

NAND Flash Type

S = SLC

Production Status

Blank = Production

ES = Engineering sample

MS = Mechanical sample

Operating Temperature Range

Blank = 0°C to 70°C

BOM Revision

1 = 1st generation

NAND Flash Component

N = M62B, 16Gb, SLC, x8

Sector Size

1 = 512-byte

Product Family

AL = P300

Hardware Feature Set

AA = Contact factory

AB = Contact factory

AC = Contact factory

P300 2.5-Inch NAND Flash SSD

Features

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 2Micron Technology, Inc. reserves the right to change products or specifications without notice.

General Description

The Micron® P300 solid state drive (SSD) uses a single-chip controller with a SATA inter-

face on the system side and n-channels of Micron NAND Flash internally. Packaged in

an industry standard 2.5-inch drive enclosure, the SSD integrates easily in existing stor-

age infrastructures.

The Micron® P300 SSD is targeted at applications that require a high percentage of ran-

dom READ/WRITE operations; high performance in terms of IOPs or latency, high en-

durance, high data retention; or applications that are deployed in harsh environments.

Figure 2: Functional Block Diagram

NAND

SATA

NAND

SSD

controller

DRAM

buffer

NAND

P300 2.5-Inch NAND Flash SSD

General Description

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 3Micron Technology, Inc. reserves the right to change products or specifications without notice.

Architecture

The P300 SSD is a NAND Flash storage device. A SATA 6 Gb/s interface connects to the

SSD externally and communicates with the controller. The controller manages data

transfers to and from the NAND Flash array.

Table 1: P300 Configurations

Unformatted Disk Density NAND Flash Process NAND Flash Density Package Count Die per BGA Package

50GB 34nm 16Gb 16 2

100GB 34nm 16Gb 16 4

200GB 34nm 16Gb 16 8

Note: 1. Density is shown as user capacity (unformatted).

Logical Block Address Configuration

The drive is set to report the number of logical block addresses (LBA) that will ensure

sufficient storage space for the specified density. Standard LBA settings, based on the

IDEMA standard (LBA1-02), are shown below.

Table 2: Standard LBA Settings

Drive Size1

Total LBAs Max LBA User Available Bytes

Decimal Hexadecimal Decimal Hexadecimal (Unformatted)

50GB 97,696,368 5D2BA70 97,696,367 5D2BA6F 50,020,549,632

100GB 195,371,568 BA52230 195,371,567 BA5222F 100,030,242,816

200GB 390,721,968 1749F1B0 390,721,967 1749F1AF 200,049,647,616

Note: 1. 1GB = 1,000,000,000 bytes.

Table 3: 2.5-Inch Nominal Dimensions and Weight

Value Unit

Height 9.5 mm

Width 69.85 mm

Length 100.50 mm

Unit weight <100 g

P300 2.5-Inch NAND Flash SSD

Architecture

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 4Micron Technology, Inc. reserves the right to change products or specifications without notice.

Interface Connectors

The SATA signal segment interface cable has four conductors and three ground connec-

tions. As shown in Package Dimensions, the cable includes a 7-pin signal segment and a

9-pin power segment arranged in a single row with a 1.27mm (0.050in) pitch.

Table 4: SATA Signal Segment Pin Assignments

Signal Name Type Description

S1 GND Ground

S2 A Differential signal pair A and A#

S3 A#

S4 GND Ground

S5 B# Differential signal pair B and B#

S6 B

S7 GND Ground

Table 5: 2.5-Inch SATA Power Segment Pin Assignments

Pin# Signal Name Description

P1 V33 No connect

P2 V33 No connect

P3 V33 No connect

P4 GND Ground

P5 GND Grond

P6 GND Ground

P7 V5 5V power, precharge

P8 V5 5V power

P9 V5 5V power

P10 GND Ground

P11 DAS1Device activity signal

P12 GND Ground

P13 V12 No connect

P14 V12 No connect

P15 V12 No connect

Note: 1. Pin 11 (DAS) may be optionally connected to GND.

P300 2.5-Inch NAND Flash SSD

Architecture

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 5Micron Technology, Inc. reserves the right to change products or specifications without notice.

Figure 3: SSD Interface Connections

Power

segment

P1 S1

Signal

segment

P300 2.5-Inch NAND Flash SSD

Architecture

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 6Micron Technology, Inc. reserves the right to change products or specifications without notice.

Device ID

Table 6: IDENTIFY Device ID

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

00 15 F 0b 0 = ATA device

14–8 X 1000100b Retired

7–6 F 01b Obsolete

5–3 X 000b Retired

2 V 0b Response incomplete

1 X 0b Retired

0 0b Reserved

01 X 3FFFh Obsolete

02 V C837h Specific configuration

03 X 0010h Obsolete

04 X 0000h 0000h Retired

06 X 003Fh Obsolete

07 0000h 0000h Reserved for the CompactFlash® Association (CFA)

09 X 0000h Retired

10 F Varies Serial number (20 ASCII characters)

20 X 0000h 0000h 0000h Retired/Obsolete

23 F Varies Firmware revision (8 ASCII characters)

27 F Varies Model number (40 ASCII characters)

47 15–8 F 80h 80h

7–0 F 10h 00h = Reserved

01h-FFh = Maximum number of logical sectors that shall be

transferred per DRQ data block on READ/WRITE MULTIPLE

commands

48 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13–1 0000000000000b Reserved for the trusted computing group

0 F 0b 1 = Trusted computing feature set is supported

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 7Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

49 15–14 00b Reserved for IDENTIFY PACKET DEVICE command

13 F 1b 1 = Standby timer values as specified in ATA-8 ACS-2 are

supported

0 = Standby timer values shall be managed by the device

12 0b Reserved for IDENTIFY PACKET DEVICE command

11 F 1b 1 = IORDY supported

0 = IORDY may be supported

10 F 1b 1 = IORDY may be disabled

9 F 1b 1 = Shall be set to 1 to indicate that LBA is supported

8 F 1b 1 = DMA support

7–2 X 00000000b Reserved

1–0 00b Current long physical sector alignment setting

50 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13–2 00000000b Reserved

1 X 0b Obsolete

0 F 1b Shall be set to 1 to indicate vendor-specific standby timer

value minimum

51 X 0000h 0000h Obsolete

53 15–8 F 00000000b Free-fall control sensitivity

00h = Vendor's recommended setting

01h-FFh = Sensitivity level; a larger number is a more sensi-

tive setting

7–3 00000b Reserved

2 F 1b 1 = The fields reported in word 88 are valid

0 = The fields reported in word 88 are not valid

1 F 1b 1 = The fields reported in words (70:64) are valid

0 = The fields reported in words (70:64) are not valid

0 X 1b Obsolete

54 X 3FFh 0010h 003Fh

FC10h 00FBh

Obsolete

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 8Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

59 15 F 1b 1 = The BLOCK ERASE EXT command is supported

14 F 0b 1 = The OVERWRITE EXT command is supported

13 F 0b 1 = The CRYPTO SCRAMBLE EXT command is supported

12 F 1b 1 = The sanitize feature set is supported

11–9 000b Reserved

8 V 1b 1 = Multiple sector setting is valid

7–0 V 00000001b Current setting for number of logical sectors that shall be

transferred per DRQ data block on READ/WRITE MULTIPLE

commands

60 F Sect Total number of user addressable logical sectors for 28-bit

commands

62 X 0000h Obsolete

63 15–11 00000b Reserved

10 V 0b 1 = Multiword DMA mode 2 is selected

0 = Multiword DMA mode 2 is not selected

9 V 0b 1 = Multiword DMA mode 1 is selected

0 = Multiword DMA mode 1 is not selected

8 V 0b 1 = Multiword DMA mode 0 is selected

0 = Multiword DMA mode 0 is not selected

7–3 0000b Reserved

2 F 1b 1 = Multiword DMA mode 2 and below is supported

1 F 1b 1 = Multiword DMA mode 1 and below is supported

0 F 1b 1 = Multiword DMA mode 0 is supported

64 15–8 00 Reserved

7–0 F 03h PIO modes support

65 F 0078h Minimum multiword DMA transfer cycle time per word in

nanoseconds (cycle time)

66 F 0078h MFR's recommended multiword DMA transfer cycle time

per word in nanoseconds (cycle time)

67 F 0078h Minimum PIO transfer cycle time without flow control in

nanoseconds (cycle time)

68 15–0 F 0078h Minimum PIO transfer cycle time with IORDY flow control in

nanoseconds (cycle time)

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 9Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

69 15 F 0b 1 = CFast™ specification support

14 F 0b 1 = Deterministic read after trim is supported

13 F 0b 1 = Long physical sector alignment error reporting control is

supported

12 F 0b 1 = DEVICE CONFIGURATION IDENTIFY DMA and DEVICE

CONFIGURATION SET DMA are supported

11 F 0b 1 = READ BUFFER DMA is supported

10 F 0b 1 = WRITE BUFFER DMA is supported

9 F 0b 1 = SET MAX PASSWORD DMA and SET MAX UNLOCK DMA

are supported

8 F 0b 1 = DOWNLOAD MICROCODE DMA is supported

7 F 0b Reserved for IEEE-1667

6 F 0b 1 = Optional ATA device 28-bit commands supported

5 F 0b 1 = Read zero after trim is supported

4–0 00000b Reserved

70 0000h Reserved

71 0000h 0000h 0000h

0000h

Reserved for the IDENTIFY PACKET DEVICE command

75 15–5 00000000000b Reserved

4–0 F 11111b Maximum queue depth - 1

76 15–13 000b Reserved for SATA

12 F 1b 1 = Supports NCQueue priority information

11 F 0b 1 - Supports unload while NCQ commands outstanding

10 F 1b 1 = Supports PHY event counters

9 F 1b 1 = Supports receipt of host-initiated partial interface pow-

er management

8 F 1b 1 = Supports NCQ feature set

7–3 0000b Reserved for SATA

2 F 1b 1 = Supports SATA Gen-2 signaling speed (3.0 Gb/s)

1 F 1b 1 = Supports SATA Gen-1 signaling speed (1.5 Gb/s)

0 F 0b Shall be cleared to 0

77 V 0004h Reserved for SATA

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 10 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

78 15–7 000000000b Reserved for SATA

6 F 1b 1 = Supports software settings preservation

5 0b Reserved for SATA

4 F 0b 1 = Supports in-order data delivery

3 F 1b 1 = Device supports initiating interface power management

(DIPM)

2 F 1b 1 = Supports DMA setup auto activation

1 F 0b 1 = Supports nonzero buffer offsets

0 F 0b Shall be cleared to 0

79 15–7 000000000b Reserved for SATA

6 V 1b 1 = Software settings preservation enabled

5 0b Reserved for SATA

4 V 0b 1 = In-order data delivery enabled

3 V 0b 1 = Device initiated power management enabled

2 V 0b 1 = DMA setup auto-activation enabled

1 V 0b 1 = Nonzero buffer offsets enabled

0 F 0b Shall be cleared to 0

80 15–10 000000b Reserved

9 F 1b 1 = Supports ATA8-ACS2

8 F 1b 1 = Supports ATA-8-ACS

7 F 1b 1 = Supports ATA/ATAPI-7

6 F 1b 1 = Supports ATA/ATAPI-6

5 F 1b 1 = Supports ATA/ATAPI-5

4 F 1b 1 = Supports ATA/ATAPI-4

3 X 0b Obsolete

2 X 0b Obsolete

1 X 0b Obsolete

0 0b Reserved

81 Minor version number

F 0028h 0028h = ATA8-ACS version 6

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 11 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

82 15 X 0b Obsolete

14 F 1b 1 = NOP command support

13 F 1b 1 = READ BUFFER command support

12 F 1b 1 = WRITE BUFFER command support

11 X 0b Obsolete

10 F 1b 1 = Host-protected area feature set support

9 F 0b Shall be cleared to 0 to indicate that the DEVICE RESET com-

mand is not supported

8 F 0b 1 = Service interrupt support

7 F 0b 1 = Release interrupt support

6 F 1b 1 = READ look-ahead support

5 F 1b 1 = Volatile write cache support

4 F 0b Shall be cleared to 0 to indicate that the PACKET feature set

is not supported

3 F 1b Shall be set to 1 to indicate that mandatory power manage-

ment feature set is supported

2 X 0b Obsolete

1 F 1b 1 = Security feature set support

0 F 1b 1 = SMART feature set support

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 12 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

83 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13 F 1b 1 = FLUSH CACHE EXT command support

12 F 1b Shall be set to 1 to indicate that the mandatory FLUSH

CACHE command is supported

11 F 1b 1 = Device configuration overlay feature set support

10 F 1b 1 = 48-bit address feature set support

9 F 0b 1 = Automatic acoustic management feature set support

8 F 1b 1 = SET MAX security extension support

7 0b Reserved for address offset reserved area boot method

6 F 0b 1 = SET FEATURES subcommand required to spin up after

power up

5 F 0b 1 = Power-up in standby feature set support

4 X 0b Obsolete

3 F 1b 1 = Advanced power management feature set support

2 F 0b 1 = CFA feature set support

1 X 0b Obsolete

0 F 1b 1 = DOWNLOAD MICROCODE command support

84 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13 F 1b 1 = The IDLE IMMEDIATE command with unload feature is

supported

12 0b Reserved for TLC

11 0b Reserved for TLC

10–9 X 00b Obsolete

8 F 1b 1 = 64-bit worldwide name support

7 X 0b Obsolete

6 F 1b 1 = WRITE DMA FUA EXT (and) WRITE MULTIPLE FUA EXT

commands are supported

5 F 1b 1 = General purpose logging feature set support

4 F 0b 1 = Streaming feature set support

3 F 0b 1 = Media card passthrough command feature set support

2 F 0b 1 = Media serial number support

1 F 1b 1 = SMART self-test support

0 F 1b 1 = SMART error logging support

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 13 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

85 15 X 0b Obsolete

14 F 1b 1 = NOP command support

13 F 1b 1 = READ BUFFER command support

12 F 1b 1 = WRITE BUFFER command support

11 X 0b Obsolete

10 V 1b 1 = Host-protected area feature set support

9 F 0b 1 = DEVICE RESET command support

8 V 0b 1 = Service interrupt enabled

7 V 0b 1 = Release interrupt enabled

6 V 1b 1 = Read look-ahead enabled

5 V 1b 1 = Volatile write cache enabled

4 F 0b 0 = Packet feature set is not supported

3 F 1b 1 = Power management feature set is enabled

2 X 0b Obsolete

1 V 0b 1 = Security feature set enabled

0 V 1b 1 = SMART feature set enabled

86 15 F 1b 1 = Words 120 and 119 are valid

14 0b 1 = Reserved

13 F 1b 1 = FLUSH CACHE EXT command supported

12 F 1b 1 = FLUSH CACHE command supported

11 F 1b 1 = Device configuration overlay (DCO) feature set suppor-

ted

10 F 1b 1 = 48-bit address feature set support

9 V 0b 1 = Automatic acoustic management feature set enabled

8 F 0b 1 = SET MAX security extension enabled by SET MAX SET

PASSWORD

7 0b Reserved for address offset reserved area boot method

6 F 0b 1 = SET FEATURES subcommand required to spin up after

power up

5 V 0b 1 = Power-up in standby feature set enabled

4 X 0b Obsolete

3 V 1b 1 = Advanced power management feature set enabled

2 F 0b 1 = CFA feature set enabled

1 X 0b Obsolete

0 F 1b 1 = DOWNLOAD MICROCODE command support

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 14 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

87 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13 F 1b 1 = IDLE IMMEDIATE command with unload feature support

12 0b Reserved for TLC

11 0b Reserved for TLC

10–9 X 00b Obsolete

8 F 1b 1 = 64-bit worldwide name support

7 X 0b Obsolete

6 F 1b 1 = WRITE DMA FUA EXT (and) WRITE MULTIPLE FUA EXT

commands are supported

5 F 1b 1 = General purpose logging feature set support

4 X 0b Obsolete

3 V 0b 1 = Media card passthrough command feature set support

2 V 0b 1 = Media serial number is valid

1 F 1b 1 = SMART self-test support

0 F 1b 1 = SMART error logging support

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 15 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

88 15 0b Reserved

14 V 0b 1 = Ultra DMA mode 6 is selected

0 = Ultra DMA mode 6 is not selected

13 V 0b 1 = Ultra DMA mode 5 is selected

0 = Ultra DMA mode 5 is not selected

12 V 0b 1 = Ultra DMA mode 4 is selected

0 = Ultra DMA mode 4 is not selected

11 V 0b 1 = Ultra DMA mode 3 is selected

0 = Ultra DMA mode 3 is not selected

10 V 0b 1 = Ultra DMA mode 2 is selected

0 = Ultra DMA mode 2 is not selected

9 V 0b 1 = Ultra DMA mode 1 is selected

0 = Ultra DMA mode 1 is not selected

8 V 0b 1 = Ultra DMA mode 0 is selected

0 = Ultra DMA mode 0 is not selected

7 0b Reserved

6 F 1b 1 = Ultra DMA mode 6 and below supported

5 F 1b 1 = Ultra DMA mode 5 and below supported

4 F 1b 1 = Ultra DMA mode 4 and below supported

3 F 1b 1 = Ultra DMA mode 3 and below supported

2 F 1b 1 = Ultra DMA mode 2 and below supported

1 F 1b 1 = Ultra DMA mode 1 and below supported

0 F 1b 1 = Ultra DMA mode 0 support

89 15–8 00h Reserved

7–0 F 01h Time required for normal erase mode SECURITY ERASE UNIT

command

90 15–8 00h Reserved

7–0 F 01h Time required for enhanced erase mode SECURITY ERASE

UNIT command

91 V 00FEh Current advanced power management value

92 V 0000h Master password identifier

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 16 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

93 15 F 0b Shall be cleared to 0

14 F 0b Shall be set to 1

13 V 0b 1 = Device detected CBLID above ViH

0 = Device detected CBLID below ViL

12 0b Reserved

11 V 0b 0 = Device 1 did not assert PDIAG

1 = Device asserted PDIAG

10–9 V 00b These bits indicate how device 1 determined the device

number:

00 = Reserved

01 = Jumper used

10 = CSEL signal used

11 = Other method used or method used unknown

8 0b Shall be set to 1

7 F 0b Reserved

6 F 0b 0 = Device 0 does not respond when device 1 is selected

1 = Device 0 responds when device 1 is selected

5 V 0b 0 = Device 0 did not detect the assertion of DASP

1 = Device 0 detected the assertion of DASP

4 V 0b 0 = Device 0 does not detect the assertion of PDIAG

1 = Device 0 detected the assertion of PDIAG

3 V 0b 0 = Device 0 failed diagnostics

1 = Device 0 passed diagnostics

2–1 V 00b These bits indicate how device 0 determined the device

number:

00 = Reserved

01 = Jumper used

10 = CSEL signal used

11 = Other method used or method used unknown

0 F 0b Shall be set to 1

94 15–8 F 00h Vendor's recommended auto acoustic management (AAM)

value

7–0 V 00h Current auto acoustic management (AAM) value

95 F 0000h Stream minimum request size

96 F 0000h Streaming transfer time – DMA

97 F 0000h Streaming access latency – DMA and PIO

98 F 0000h 0000h Streaming performance granularity

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 17 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

100 F LBA Maximum user LBA for 48-bit address feature set

104 F 0000h Streaming transfer time – PIO

105 F 0008h Maximum number of 512-byte blocks of LBA range entries

per DATA SET MANAGEMENT command

106 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13 F 0b 1 = Device has multiple logical sectors per physical sector

12 F 0b 1 = Device logical sector size > 256 words

11–4 F 00000000b Reserved

3–0 F 0000b 2xP logical sectors per physical sector

107 F 0000h Interseek delay for ISO-7779 standard acoustic testing

108 15–12 F 0101b NAA (3–0)

11–0 F 000000001010b IEEE OUI (23–12)

109 15–4 F Varies IEEE OUI (11–0)

3–0 Varies Unique ID (35–32)

110 F Varies 5–0 Unique ID (31–16)

111 F Varies Unique ID (15–0)

112 0000h 0000h 0000h

0000h

Reserved

116 0000h Reserved for TLC

117 F 0000h 0000h Logical sector size

119 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13–8 000000b Reserved

7 F 0b 1 = Extended power conditions feature set supported

6 F 1b 1 = Extended sense data reporting feature set supported

5 F 1b 1 = Free-fall control feature set supported

4 F 1b 1 = DOWNLOAD MICROCODE command with mode 3 sup-

ported

3 F 1b 1 = READ LOG DMA EXT (and) WRITE LOG DMA EXT com-

mand support

2 F 1b 1 = WRITE UNCORRECTABLE EXT support

1 F 0b 1 = Write-read-verify feature set support

0 F 0b Reserved for DDT

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 18 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

120 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13–8 000000b Reserved

7 V 0b 1 = At least one extended power conditions idle timer is en-

abled

6 V 0b 1 = Extended sense data reporting feature set enabled

5 V 0b 1 = Free-fall control feature set enabled

4 F 1b 1 = DOWNLOAD MICROCODE command with mode 3 sup-

ported

3 F 1b 1 = READ LOG DMA EXT (and) WRITE LOG DMA EXT com-

mand support

2 F 0b 1 = WRITE UNCORRECTABLE EXT support

1 V 0b 1 = Write-read-verify feature set enabled

0 0b Reserved for DDT

121 0000h 0000h 0000h

0000h 0000h 0000h

Reserved for expanded support and enabled settings

127 X 0000h Obsolete

128 15–9 0000000b Reserved

8 V 0b Master password capability: 0 = High, 1 = Maximum

7–6 00b Reserved

5 F 1b 1 = Enhanced security erase support

4 V 0b 1 = Security count expired

3 V 0b 1 = Security frozen

2 V 0b 1 = Security locked

1 V 0b 1 = Security enabled

0 F 1b 1 = Security supported

129 X Varies Vendor specific

160 15 F 0b CFA power mode

14 0b Word 160 supported

13 F 0b CFA power mode 1 is required for one or more commands

implemented by the device

12 V 0b CFA power mode 1 disabled

11–0 F 000000000000b Maximum current in ma

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 19 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

161 F 0000h 0000h 0000h

0000h 0000h 0000h

0000h

Reserved for assignment by the CFA

168 15–4 000h Reserved

3–0 F 3h Device nominal form factor (DNFF)

169 15–1 F 000000000000000b Reserved

0 F 1b 1 = Trim bit of the DATA SET MANAGEMENT command sup-

ported

170 F 0000h 0000h 0000h

0000h

Additional product identifier

174 0000h 0000h Reserved

176 F Varies Current media serial number (60 ASCII characters; not sup-

ported)

206 15–12 X 0000b Vendor specific

11–6 000000b Reserved

5 F 1b SCT data tables command support

4 F 1b SCT FEATURES CONTROL command support

3 F 1b SCT ERROR RECOVERY CONTROL command support

2 F 1b SCT WRITE SAME command support

1 F 0b Obsolete

0 F 1b SCT command transport support

207 F 0000h 0000h Reserved FOR CE-ATA

209 15 F 0b Shall be cleared to 0

14 F 1b Shall be set to 1

13–0 F 00000000000000b Logical sector offset within the first physical sector where

the first logical sector is placed

210 V 0000h 0000h Write-read-verify sector count mode 3

212 F 0000h 0001h Write-read-verify sector count mode 2

214 15–12 F 0000b NV cache feature set version

11–8 F 0000b NV cache power mode feature set version

7–5 000b Reserved

4 V 0b 1 = NV cache feature set enabled

3–2 00b Reserved

1 V 0b 1 = NV cache power mode feature set enabled

0 F 0b 1 = NV cache power mode feature set support

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 20 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

215 V 0000h NV cache size in logical blocks (LSW)

216 V 0000h NV cache size in logical blocks (MSW)

217 F 0001h Nominal media rotation rate

218 0000h Reserved

219 15–8 00h Reserved

7–0 F 00h Device estimated time to spin up in seconds

220 15–8 00h Reserved

7–0 V 00h Write-read-verify feature set current mode

221 0000h Reserved

222 15–12 F 0001b Transport type: 0 = Parallel; 1 = SATA; 2–15 = Reserved

11–6 000000b 0 = Reserved

1 = Reserved

5 F 1b 0 = Reserved

1 = SATA Rev. 3.0

4 F 1b 0 = Reserved

1 = SATA Rev. 2.6

3 F 1b 0 = Reserved

1 = SATA Rev. 2.5

2 F 1b 0 = Reserved

1= SATA II: extensions

1 F 1b 0 = ATA/ATAPI-7

1= SATA 1.0a

0 F 1b 0 = ATA8-APT

1 = ATA8-AST

223 F 0000h Transport minor revision number

224 0000h 0000h 0000h

0000h 0000h 0000h

0000h

Reserved

234 F 0001h Minimum number of 512-byte units per DOWNLOAD MI-

CROCODE command mode 3

235 F 00FFh Maximum number of 512-byte units per DOWNLOAD MI-

CROCODE command mode 3

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 21 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 6: IDENTIFY Device ID (Continued)

• F = The content of the word is fixed and does not change

• V = The content of the word is variable and may change depending on the state of the device or the commands execu-

ted by the device

• X = The fixed or variable type of this field is not defined in the governing standard

• R = The content of the word is reserved and shall be zero

Word Bit(s) Setting Default Value Description

236 0000h 0000h 0000h

0000h 0000h 0000h

0000h

Reserved

255 15–8 F Varies Checksum

7–0 F A5h Signature

P300 2.5-Inch NAND Flash SSD

Device ID

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 22 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Commands

Table 7: Supported ATA Command Set

See ATA8-ACS2 standard for command details

Command Name Command Code (Hex)

CHECK POWER MODE 98h

CHECK POWER MODE E5h

DEVICE CONFIGURATION B1h

DOWNLOAD MICROCODE 92h

FLUSH CACHE E7h

FLUSH CACHE EXT EAh

IDLE E3h

IDLE 97h

IDLE IMMEDIATE 95h

IDLE IMMEDIATE E1h

NOP 00h

READ BUFFER E4h

READ BUFFER DMA E9h

READ DMA C8h

READ DMA EXT 25h

READ DMA (without retries) C9h

READ FPDMA QUEUED 60h

READ LOG DMA EXT 47h

READ LOG EXT 2Fh

READ MULTIPLE C4h

READ MULTIPLE EXT 29h

READ NATIVE MAX ADDRESS F8h

READ NATIVE MAX ADDRESS EXT 27h

READ SECTORS 20h

READ SECTORS EXT 24h

READ SECTORS (without retry) 21h

READ VERIFY SECTORS 40h

READ VERIFY SECTORS EXT 42h

READ VERIFY SECTORS (without retry) 41h

RECALIBRATE 10h

REQUEST SENSE DATA EXT 0Bh

SECURITY DISABLE PASSWORD F6h

SECURITY ERASE PREPARE F3h

SECURITY ERASE UNIT F4h

SECURITY FREEZE LOCK F5h

SECURITY SET PASSWORD F1h

P300 2.5-Inch NAND Flash SSD

Commands

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 23 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Table 7: Supported ATA Command Set (Continued)

See ATA8-ACS2 standard for command details

Command Name Command Code (Hex)

SECURITY UNLOCK F2h

SEEK 70h

SET FEATURES EFh

SET MAX ADDRESS F9h

SET MULTIPLE MODE C6h

SET NATIVE MAX ADDRESS EXT 37h

SLEEP 99h

SLEEP E6h

SMART B0h

STANDBY E2h

STANDBY 96h

STANDBY IMMEDIATE 94h

STANDBY IMMEDIATE E0h

WRITE BUFFER E8h

WRITE BUFFER DMA EBh

WRITE DMA CAh

WRITE DMA EXT 35h

WRITE DMA FUA EXT 3Dh

WRITE DMA (without retries) CBh

WRITE FPDMA QUEUED 61h

WRITE LOG DMA EXT 57h

WRITE LOG EXT 3Fh

WRITE MULTIPLE C5h

WRITE MULTIPLE EXT 39h

WRITE MULTIPLE FUA EXT CEh

WRITE SECTORS 30h

WRITE SECTORS EXT 34h

WRITE SECTORS (without retry) 31h

P300 2.5-Inch NAND Flash SSD

Commands

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 24 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Reliability

Micron SSDs incorporate advanced technology for defect and error management. Mi-

cron uses various combinations of hardware-based error correction algorithms and

firmware-based static and dynamic wear-leveling algorithms.

Over the life of the SSD, uncorrectable errors may occur. An uncorrectable error is de-

fined as data that is reported as successfully programmed to the SSD but when it is read

out of the SSD, the data differs from what was programmed.

Table 8: Uncorrectable Bit Error Rate

Uncorrectable Bit Error Rate Operation

<1 sector per 1016 bits read READ

Mean Time Between Failures

Mean time between failures (MTBFs) for the SSD can be predicted based on the compo-

nent reliability data using the methods referenced in the Telcordia SR-332 reliability

prediction procedures for electronic equipment.

Table 9: MTBFs

Density MTBF (Operating Hours)1

50GB 2 million

100GB 2 million

200GB 2 million

Note: 1. The product achieves a mean time between failure (MTBF) of 2 million hours, based on

population statistics not relevant to individual units.

Endurance

Endurance for the SSD can be predicted based on the usage conditons applied to the

device, the internal NAND component cycles, the write amplification factor, and the

wear-leveling efficency of the drive. The table below shows the drive lifetime for each

SSD density based on predefined usage conditions.

Table 10: Drive Lifetime

Density Drive Lifetime (Total Bytes Written)

50GB .875PB

100GB 1.75PB

200GB 3.5PB

Notes: 1. Total bytes written calculated with the drive 100% full.

2. Access patterns are 50% sequential and 50% random. Random accesses: 10% are 512B;

50% are 4K; 15% are 32K; 15% are 64K; and 10% are 128K. Sequential accesses: 100%

are 128K.

P300 2.5-Inch NAND Flash SSD

Reliability

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 25 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Data Retention

Micron SSD data retention at beginning of life: 10 years at 25°C

Micron SSD data retention at end of life: 1 year at 25°C

P300 2.5-Inch NAND Flash SSD

Reliability

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 26 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Electrical Characteristics

Table 11: SATA Typical Power Consumption

Density Idle/Standby/Sleep Secure Erase

SEQ

Write/Read

(128K XFR)

RND

Write/Read

(4K XFR) Unit

50GB 125 1000 2500/1800 1900/1500 mW

100B 125 1200 3000/2000 2200/1700 mW

200GB 125 1400 3500/2200 2500/1900 mW

Table 12: Maximum Ratings

Parameter/Condition Symbol Min Max Unit

Voltage input V5 4.5 5.5 V

Operating temperature TA0 70 °C

Non-operating temperature –40 85 °C

Rate of temperature change – 20 °C/hour

Relative humidity (noncondensing) 5 95 %

Stresses greater than those listed may cause permanent damage to the device. This is a

stress rating only, and functional operation of the device at these or any other condi-

tions above those indicated in the operational sections of this specification is not im-

plied. Exposure to absolute maximum rating conditions for extended periods may affect

reliability.

Table 13: Shock and Vibration

Parameter/Condition Specification

Operating shock 1500G/0.5ms

Operating vibration 5–500Hz at 3.1G

P300 2.5-Inch NAND Flash SSD

Electrical Characteristics

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 27 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Compliance

Micron SSDs comply with the following:

• RoHS compliant

• Halogen free

• SATA-IO

• WHQL

• CE (Europe): EN55022, 2006 Class B and EN55024, 1998 + A1: 2001 + A2:2003

• FCC: CFR Title 47, Part 15, ICES-003, all Class B

• UL (US): approval to UL-60950-1, 2nd Edition, 2007-03-27, IEC 60950-1:2005, 2nd Ed-

ition

• BSMI (Taiwan): approval to CNS 13438

• C-TICK (Australia, New Zealand): approval to AS/NZS CISPR22

• KCC RRL (Korea): approval to KCC MU2-C30025, KCC MU2-C30018 Class B

• W.E.E.E.: Compliance with EU WEEE directive 2002/96/EC. Additional obligations

may apply to customers who place these products in the markets where WEEE is en-

forced.

• TUV (Germany): approval to IEC60950/EN60950

• VCCI

FCC Rules

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide rea-

sonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio fre-

quency energy and, if not installed and used in accordance with the instruction manual,

may cause harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

P300 2.5-Inch NAND Flash SSD

Compliance

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 28 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Package Dimensions

Figure 4: 2.5-Inch Package

(100.50mm)

(3.957in)

(0.30mm)

(0.012in)

14.00mm

0.551in 90.60mm

3.567in

4.07mm

0.160in

61.71mm

2.430in

M3 x 0.5mm

69.85mm ±0.25

2.750in ±0.010

14.00mm

0.551in

90.60mm

3.567in

3.00mm

0.118in

M3 x 0.5mm

(2 PLCS)

3.50mm ±0.38

0.138in ±0.015

13.43mm

0.529in 9.50mm ±0.20

0.374in ±0.008

9.40mm

0.370in 3.0mm

0.12in RAD

100.20mm ±0.25

3.945in ±0.01

Notes: 1. Maximum mounting screw length: Bottom = M3 x 0.5 x 3; Side = M3 x 0.5 x 4

2. Maximum torque: 4.5 in-lb

Figure 5: Thermocouple Placement Guidelines for Temperature Measurement

3mm 3mm

Center thermocouple here

Power and data connectors

3mm

71.2mm

35.5mm

34.5mm

30.8mm

Non-label side of SSD

P300 2.5-Inch NAND Flash SSD

Package Dimensions

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 29 Micron Technology, Inc. reserves the right to change products or specifications without notice.

References

• Serial ATA: High-speed serialized AT attachment, Serial ATA working group, available

at www.sata-io.org

• Small Form Factor Specification SFF-8201, SFF-8223

• Electronic Industries Association Standard, EIA-720

• Telcordia SR-332 reliability prediction procedures for electronic equipment

• IDEMA Document LBA1-02

P300 2.5-Inch NAND Flash SSD

References

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 30 Micron Technology, Inc. reserves the right to change products or specifications without notice.

Revision History

Rev. K – 5/12

• Added center thermocouple graphic to package dimensions.

Rev. J – 4/12

• Added notes to package dimension graphic.

Rev. I – 10/11

• Added FCC rules to Compliance.

Rev. H – 5/11

• Added DOWNLOAD MICROCODE command to Table 7: Supported ATA Command

Set; changed hex format of command codes.

Rev. G – 5/11

• Changed overall length of the enclosure + connector from absolute maximums to ref-

erence dimensions in packaging figure.

Rev. F – 4/11

• Removed references to altitude from Features section.

Rev. E – 4/11

• Removed references to green from Compliance section.

8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900

www.micron.com/productsupport Customer Comment Line: 800-932-4992

Micron and the Micron logo are trademarks of Micron Technology, Inc.

All other trademarks are the property of their respective owners.

This data sheet contains minimum and maximum limits specified over the power supply and temperature range set forth herein.

Although considered final, these specifications are subject to change, as further product development and data characterization some-

times occur.

P300 2.5-Inch NAND Flash SSD

Revision History

PDF: 09005aef840793dc

p300_2_5.pdf - Rev. K 5/12 EN 31 Micron Technology, Inc. reserves the right to change products or specifications without notice.