WKFN 4 TKG/35 56.704.4055.0 100
THSI 6,3x32 Z1.298.1653.0 10
THSI 6,3x32 LED24 Z1.298.1753.0 10
THSI 6,3x32 LED60 Z1.298.1853.0 10
THSI 6,3x32 GL250 Z1.298.1953.0 10
THSI 6,3x32 GL500 Z1.298.2053.0 10
35x27x7,5 EN 60715 98.300.0000.0 1
35x24x15 EN 60715 98.360.0000.0 1
9708/2 S35 Z5.522.8553.0 100
WEF 1/35 Z5.523.9353.0 100
APFN 4 D2/2 07.312.9055.0 10
ZP/WKFN 4 TKG 07.313.1655.0 10
TWFN 4 D2/2 07.312.9155.0 10
IVB WKF 4-2 Z7.261.1227.0 10
IVB WKF 4-3 Z7.261.1327.0 10
IVB WKF 4-4 Z7.261.1427.0 10
IVB WKF 4-5 Z7.261.1527.0 10
IVB WKF 4-6 Z7.261.1627.0 10
IVB WKF 4-7 Z7.261.1727.0 20
IVB WKF 4-8 Z7.261.1827.0 20
IVB WKF 4-9 Z7.261.1927.0 20
IVB WKF 4-10 Z7.261.2027.0 20
LEL 4/1 WEISS 05.561.8553.0 100
LEL 4/2 GRAU 05.561.8653.0 100
LEL 4/3 SCHWARZ 05.561.8753.0 100
ADF 4/4 GELB 04.343.6153.8 10
ST 2/2,3 Z5.553.2921.0 10
DIN 5264 B 0,6x3,5 06.502.4000.0 5
DIN 5264 B 0,6x3,5 M 06.502.5000.0 10
WKFN 4 TKG/35 56.704.4055.0 100
THSI 5x20 Z1.298.1053.0 10
THSI 5x20 LED24 Z1.298.1153.0 10
THSI 5x20 LED60 Z1.298.1253.0 10
THSI 5x20 GL250 Z1.298.1353.0 10
35x27x7,5 EN 60715 98.300.0000.0 1
35x24x15 EN 60715 98.360.0000.0 1
9708/2 S35 Z5.522.8553.0 100
WEF 1/35 Z5.523.9353.0 100
APFN 4 D2/2 07.312.9055.0 10
TWFN 4 D2/2 07.312.9155.0 10
IVB WKF 4-2 Z7.261.1227.0 10
IVB WKF 4-3 Z7.261.1327.0 10
IVB WKF 4-4 Z7.261.1427.0 10
IVB WKF 4-5 Z7.261.1527.0 10
IVB WKF 4-6 Z7.261.1627.0 10
IVB WKF 4-7 Z7.261.1727.0 20
IVB WKF 4-8 Z7.261.1827.0 20
IVB WKF 4-9 Z7.261.1927.0 20
IVB WKF 4-10 Z7.261.2027.0 20
LEL 4/1 WEISS 05.561.8553.0 100
LEL 4/2 GRAU 05.561.8653.0 100
LEL 4/3 SCHWARZ 05.561.8753.0 100
ADF 4/4 GELB 04.343.6153.8 10
ST 2/2,3 Z5.553.2921.0 10
DIN 5264 B 0,6x3,5 06.502.4000.0 5
DIN 5264 B 0,6x3,5 M 06.502.5000.0 10
Fuse blocks
with tension spring connection
1) When selecting G fuse inserts, make sure that the
specified maximum power is not exceeded.
The current is determined by the inserted fuse.
2) The voltage range is determined by the built-in
LED display.
Depending on the application and the installation
method, the circumstances for increased
temperature must be checked in the closed fuse
holders.
Higher ambient temperatures are an additional load
for the fuse inserts. Therefore, the reduction of the
rated current must be considered accordingly in
these applications.
Indicator (24 V): LED, red
current consumption: 10.3 mA
Indicator (220 V): LED, red
current consumption: 0.3 mA
EN 60 947-7-3:2002
UL ratings field/factory wiring
CSA ratings
KEMA 01 ATEX 2087 U1) EN 60 079-0/EN 60 079-7
Width Wire strip length
Approvals
WKFN 4 TKG with THSi 5 x 20
fine-stranded solid V A
0.13 – 4 mm2 0.13 – 6 mm2 500 V/8 kV/3 1)
6 mm 11 mm
q w
pending
WKFN 4 TKG with THSi 6,3 x 32
fine-stranded solid V A
0.13 – 4 mm2
0.13 – 6 mm2 500 V/8 kV/3 1)
6 mm 11 mm
q w
pending
Disconnect ground block gray
Fuse disconnect lever
Fuse disconnect lever with LED 12 – 24 V2)
Fuse disconnect lever with LED 24 – 60 V2)
Fuse disconnect lever with GL 110 – 250 V2)
Fuse disconnect lever with GL 500 V2)
Supply block gray
Accessories
1. Mounting rail 35, 7.5 mm high L = 2 m
Mounting rail 35, 15 mm high L = 2 m
2. End clamp TS 35, with screw 8 mm wide
End clamp TS 35, screwless 8 mm wide
3. End plate gray
Intermediate plate, 4 mm wide blue
4. Partition plate gray
5. Cross connector 2 pole
insulated 3 pole
4 pole
5 pole
6 pole
7 pole
8 pole
9 pole
10 pole
6. Wire entry guide 0.13 – 0.2 mm2
0.25 – 0.5 mm2
0.75 – 1.0 mm2
7. Cover with warning symbol over 4 blocks
8. Test plug
9. Screwdriver, uninsulated
Screwdriver, uninsulated, MINI
Marking accessories see page 76 – 79
Subject to change without further notice
Type Part No. Std. Pack Type Part No. Std. Pack