HIGH-SPEED 3.3V 4K x 16 DUAL-PORT STATIC RAM Features True Dual-Ported memory cells which allow simultaneous reads of the same memory location High-speed access - Commercial: 15/20/25/35/55ns (max.) - Industrial: 20/25/35/55ns (max.) Low-power operation - IDT70V24S Active: 400mW (typ.) Standby: 3.3mW (typ.) - IDT70V24L Active: 380mW (typ.) Standby: 660W (typ.) Separate upper-byte and lower-byte control for multiplexed bus compatibility IDT70V24S/L IDT70V24 easily expands data bus width to 32 bits or more using the Master/Slave select when cascading more than one device M/S = VIH for BUSY output flag on Master M/S = VIL for BUSY input on Slave BUSY and Interrupt Flag On-chip port arbitration logic Full on-chip hardware support of semaphore signaling between ports Fully asynchronous operation from either port LVTTL-compatible, single 3.3V (0.3V) power supply Available in 84-pin PGA, 84-pin PLCC and 100-pin TQFP Industrial temperature range (-40C to +85C) is available for selected speeds Functional Block Diagram R/WL R/WR LBL CEL OEL LBR CER OER UBR UBL I/O8L-I/O15L I/O8R-I/O15R I/O Control I/O Control I/O0R-I/O7R I/O0L-I/O7L (1,2) BUSYR (1,2) BUSY L A11L A0L Address Decoder MEMORY ARRAY 12 CEL OEL R/WL SEML (2) INTL Address Decoder A11R A0R 12 ARBITRATION INTERRUPT SEMAPHORE LOGIC M/S CER OER R/WR SEMR INTR(2) 2911 drw 01 NOTES: 1. (MASTER): BUSY is output; (SLAVE): BUSY is input. 2. BUSY outputs and INT outputs are non-tri-stated push-pull. MARCH 2000 1 (c)2000 Integrated Device Technology, Inc. DSC-2911/8 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Description The IDT70V24 is a high-speed 4K x 16 Dual-Port Static RAM. The IDT70V24 is designed to be used as a stand-alone 64K-bit Dual-Port RAM or as a combination MASTER/SLAVE Dual-Port RAM for 32-bit-or-more word systems. Using the IDT MASTER/SLAVE Dual-Port RAM approach in 32-bit or wider memory system applications results in full-speed, errorfree operation without the need for additional discrete logic. This device provides two independent ports with separate control, address, and I/O pins that permit independent, asyn-chronous access for reads or writes to any location in memory. An automatic power down feature controlled by CE permits the on-chip circuitry of each port to enter a very low standby power mode. Fabricated using IDT's CMOS high-performance technology, these devices typically operate on only 400mW of power. The IDT70V24 is packaged in a ceramic 84-pin PGA, an 84-Pin PLCC and a 100-pin Thin Quad Flatpack. A11L A10L A9L A8L A0R A1R A2R A3R A4R A5R A6R N/C N/C N/C N/C I/O10L I/O11L I/O12L I/O13L GND I/O14L I/O15L VCC GND I/O0R I/O1R I/O2R VCC I/O3R I/O4R I/O5R I/O6R N/C N/C N/C N/C 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 1 75 74 2 3 73 4 72 5 71 6 70 7 69 8 68 9 67 66 10 11 12 13 14 IDT70V24PF PN100-1(4) 100-Pin TQFP Top View(5) 65 64 63 62 15 61 16 60 17 59 18 58 19 57 20 56 21 55 22 54 23 53 24 52 51 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 N/C N/C N/C N/C A5L A4L A3L A2L A1L A0L INTL BUSYL GND M/S BUSYR INTR A0R A1R A2R A3R A4R N/C N/C N/C N/C 6.42 2 N/C A11R A10R A9R A8R A7R A6R A5R 2911 drw 03 I/O7R I/O8R I/O9R I/O10R I/O11R I/O12R I/O13R I/O14R GND I/O15R NOTES: 1. All VCC pins must be connected to power supply. 2. All GND pins must be connected to ground supply. 3. J84-1 package body is approximately 1.15 in x 1.15 in x .17 in. PN100-1 package body is approximately 14mm x 14mm x 1.4mm. 4. This package code is used to reference the package diagram. 5. This text does not indicate orientation of the actual part-marking. I/O9L I/O8L I/O7L I/O6L I/O5L I/O4L I/O3L I/O2L GND I/O1L I/O0L Index N/C A11L A10L A9L A8L A7L A6L 2911 drw 02 SEML CEL UBL LBL A7R N/C A11R A10R A9R A8R SEMR CER UBR LBR 29 30 31 32 54 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 M/S BUSYR INTR SEMR CER UBR LBR 25 26 27 28 GND OE L 84-Pin PLCC Top View(5) INTL BUSYL VCC R/WL IDT70V24J J84-1(4) OER N/C SEML CEL UBL LBL 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 A7L A6L A5L A4L A3L A2L A1L A0L R/WR GND 21 22 23 24 I/O9R I/O10R I/O11R I/O12R I/O13R I/O14R GND I/O15R I/O8R 14 15 16 17 18 19 20 3 2 1 84 83 82 81 80 79 78 77 76 75 74 73 OER VCC GND I/O0R I/O1R I/O2R VCC I/O3R I/O4R I/O5R I/O6R I/O7R 11 10 9 8 7 6 5 4 12 13 R/WR GND I/O8L I/O9L I/O10L I/O11L I/O12L I/O13L GND I/O14L I/O15L OEL INDEX VCC R/WL I/O7L I/O6L I/O5L I/O4L I/O3L I/O2L GND I/O1L I/O0L Pin Configurations(1,2,3) IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Pin Configurations(1,2,3) (con't.) 63 11 61 I/O7L 66 10 64 I/O10L 67 09 47 CE L 45 A11L 43 A9L 41 R/W L IDT70V24G G84-3(4) 74 GND GND 32 29 26 80 I/O3R 83 I/O5R 7 1 I/O6R 2 I/O9R 3 I/O8R A 5 I/O10R 4 I/O11R B 11 GND I/O7R 8 I/O13R 6 I/O14R C D 14 E 13 20 A11R 16 22 A8R CE R N/C F G H 19 A10R K A7R L 2911 drw 04 Index NOTES: 1. All VCC pins must be connected to power supply. 2. All GND pins must be connected to ground supply. 3. Package body is approximately 1.12 in x 1.12 in x .16 in. 4. This package code is used to reference the package diagram. 5. This text does not indicate orientation of the actual part-marking. A4R 21 A9R J A3R 24 A6R 18 LB R A1R 25 A5R 17 UB R R/W R 15 OE R 23 SEM R 10 I/O15R 9 I/O12R 12 GND BUSY R 27 A2R I/O4R A1L 30 INT R A0R INT L 36 M/S 28 VCC A2L 34 A0L 31 GND 84-Pin PGA Top View(5) 78 I/O2R 35 BUSY L A4L 37 A3L 33 A5L 39 A6L VCC A7L 40 A8L 52 VCC 42 A10L 44 N/C 73 77 84 01 46 LB L 38 I/O14L I/O1R 82 02 50 UB L 53 GND 48 SEM L 49 I/O1L 57 70 81 03 56 I/O3L 51 OE L I/O12L I/O0R 79 04 I/O6L I/O9L 71 I/O15L 76 05 59 62 54 I/O0L 68 I/O13L 75 06 55 I/O2L 65 72 07 58 I/O4L I/O8L I/O11L 69 08 60 I/O5L Pin Names Left Port Right Port Names CEL CER Chip Enable R/ WL R/ WR Read/Write Enable OEL OER Output Enable A0L - A11L A 0R - A11R Address I/O0L - I/O15L I/O0R - I/O15R Data Input/Output SEML SEMR Semaphore Enable UBL UBR Upper Byte Select LBL LBR Lower Byte Select INTL INTR Interrupt Flag BUSYL BUSYR Busy Flag M/ S Master or Slave Select VCC Power GND Ground 2911 tbl 01 6.42 3 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Truth Table I: Non-Contention Read/Write Control Inputs(1) Outputs CE R/W OE UB LB SEM I/O8-15 I/O0-7 H X X X X H High-Z High-Z Deselected: Power Down X X X H H H High-Z High-Z Both Bytes Deselected L L X L H H DATAIN High-Z Write to Upper Byte Only L L X H L H High-Z DATAIN Write to Lower Byte Only L L X L L H DATAIN DATAIN Write to Both Bytes L H L L H H DATAOUT High-Z Read Upper Byte Only L H L H L H High-Z DATAOUT Read Lower Byte Only L H L L L H DATAOUT DATAOUT Read Both Bytes X X H X X X High-Z High-Z Outputs Disabled Mode 2911 tbl 02 NOTE: 1. A0L -- A 11L A 0R -- A 11R Truth Table II: Semaphore Read/Write Control(1) Inputs Outputs CE R/ W OE UB LB SEM I/O8-15 I/O0-7 H H L X X L DATAOUT DATAOUT Read Data in Semaphore Flag X H L H H L DATAOUT DATAOUT Read Data in Semaphore Flag H X X X L DATAIN DATAIN Write DIN0 into Semaphore Flag X X H H L DATAIN DATAIN Write DIN0 into Semaphore Flag L X X L X L ____ ____ Not Allowed L ____ ____ Not Allowed L X X X L Mode 2911 tbl 03 NOTE: 1. There are eight semaphore flags written to via I/O 0 and read from all of the I/O's (I/O0-I/O15 ). These eight semaphores are addressed by A0-A2. 6.42 4 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Absolute Maximum Ratings(1) Symbol Commercial & Industrial Unit Terminal Voltage with Respect to GND -0.5 to +4.6 V TBIAS Temperature Under Bias -55 to +125 o C TSTG Storage Temperature -55 to +125 o C IOUT DC Output Current V TERM(2) Rating 50 Maximum Operating Temperature and Supply Voltage(1) Grade Ambient Temperature GND Vcc Commercial 0OC to +70OC 0V 3.3V + 0.3V -40OC to +85OC 0V 3.3V + 0.3V Industrial 2911 tbl 05 NOTES: 1. This is the parameter TA. mA 2911 tbl 04 NOTES: 1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability. 2. VTERM must not exceed Vcc +0.3V for more than 25% of the cycle time or 10ns maximum, and is limited to < 20mA for the period over VTERM > Vcc + 0.3V . Recommended DC Operating Conditions Symbol Capacitance (TA = +25C, f = 1.0MHz) Symbol CIN COUT Parameter Conditions Input Capacitance Output Capacitance (2) Max. Unit VIN = 3dV 9 pF VOUT = 3dV 11 Parameter V CC Supply Voltage GND Ground Min. Typ. Max. Unit 3.0 3.3 3.6 V 0 0 0 VIH Input High Voltage 2.0 ____ VIL Input Low Voltage -0.3(1) ____ V (2) VCC+0.3 0.8 V V 2911 tbl 06 NOTES: 1. VIL> -1.5V for pulse width less than 10ns. 2. VTERM must not exceed Vcc + 0.3V. pF 2911 tbl 07 NOTES: 1. This parameter is determined by device characterization but is not production tested. 2. 3dV references the interpolated capacitance when the input and output signals switch from 0V to 3V or from 3V to 0V. DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range (VCC = 3.3V 0.3V) 70V24S Symbol Parameter Test Conditions Min. Max. Min. Max. Unit 10 ___ 5 A 10 ___ 5 A ___ 0.4 ___ 0.4 V 2.4 ___ 2.4 ___ V (1) Input Leakage Current VCC = 3.6V, VIN = 0V to VCC ___ |ILO| Output Leakage Current CE = VIH, VOUT = 0V to V CC ___ VOL Output Low Voltage IOL = +4mA VOH Output High Voltage IOH = -4mA |ILI| 70V24L 2911 tbl 08 NOTE: 1. At VCC < 2.0V input leakages are undefined. 6.42 5 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges DC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1) (VCC = 3.3V 0.3V) 70V24X15 Com'l Only Symbol ICC ISB1 ISB2 ISB3 ISB4 Parameter Dynamic Operating Current (Both Ports Active) Standby Current (Both Ports - TTL Level Inputs) Standby Current (One Port - TTL Level Inputs) Full Standby Current (Both Ports CMOS Level Inputs) Full Standby Current (One Port CMOS Level Inputs) Test Condition CE = VIL, Outputs Open SEM = VIH Version 70V24X20 Com'l & Ind 70V24X25 Com'l & Ind Typ. (2) Max. Typ. (2) Max. Typ. (2) Max. Unit mA COM'L S L 150 140 215 185 140 130 200 175 130 125 190 165 IND S L ____ ____ ____ ____ 140 130 225 195 130 125 210 180 COM'L S L 25 20 35 30 20 15 30 25 16 13 30 25 MIL & IND S L ____ ____ ____ ____ 20 15 45 40 16 13 45 40 COM'L S L 85 80 120 110 80 75 110 100 75 72 110 95 MIL & IND S L ____ ____ ____ ____ 80 75 130 115 75 72 125 110 Both Ports CEL and CER > VCC - 0.2V, VIN > V CC - 0.2V or VIN < 0.2V, f = 0 (4) SEMR = SEML > VCC-0.2V COM'L S L 1.0 0.2 5 2.5 1.0 0.2 5 2.5 1.0 0.2 5 2.5 MIL & IND S L ____ ____ ____ ____ 1.0 0.2 15 5 1.0 0.2 15 5 CE"A" < 0.2V and CE"B" > V CC - 0.2V(5) SEMR = SEML > VCC-0.2V COM'L S L 85 80 125 105 80 75 115 100 75 70 105 90 MIL & IND S L ____ ____ ____ ____ 80 75 130 115 75 70 120 105 (3) f = fMAX CER and CEL = VIH SEMR = SEML = VIH mA (3) f = fMAX CE"A" = V IL and CE"B" = VIH(5) Active Port Outputs Open, f=fMAX(3) SEMR = SEML = VIH VIN > V CC - 0.2V or V IN < 0.2V Active Port Outputs Open, f = fMAX(3) mA mA mA 2911 tbl 09a 70V24X35 Com'l & Ind Symbol ICC ISB1 ISB2 ISB3 ISB4 Parameter Dynamic Operating Current (Both Ports Active) Standby Current (Both Ports - TTL Level Inputs) Standby Current (One Port - TTL Level Inputs) Full Standby Current (Both Ports CMOS Level Inputs) Full Standby Current (One Port CMOS Level Inputs) Test Condition Version CE = VIL, Outputs Open SEM = VIH 70V24X55 Com'l & Ind Typ. (2) Max. Typ. (2) Max. Unit mA COM'L S L 120 115 180 155 120 115 180 155 IND S L 120 115 200 170 120 115 200 170 COM'L S L 13 11 25 20 13 11 25 20 MIL & IND S L 13 11 40 35 13 11 40 35 COM'L S L 70 65 100 90 70 65 100 90 MIL & IND S L 70 65 120 105 70 65 120 105 Both Ports CEL and CER > VCC - 0.2V, VIN > VCC - 0.2V or VIN < 0.2V, f = 0 (4) SEMR = SEML > VCC-0.2V COM'L S L 1.0 0.2 5 2.5 1.0 0.2 5 2.5 MIL & IND S L 1.0 0.2 15 5 1.0 0.2 15 5 CE"A" < 0.2V and CE"B" > VCC - 0.2V(5) SEMR = SEML > VCC-0.2V COM'L S L 65 60 100 85 65 60 100 85 MIL & IND S L 65 60 115 100 65 60 115 100 (3) f = fMAX CER and CEL = VIH SEMR = SEML = VIH mA (3) f = fMAX CE"A" = VIL and CE"B" = VIH(5) Active Port Outputs Open, f=fMAX(3) SEMR = SEML = VIH VIN > VCC - 0.2V or V IN < 0.2V Active Port Outputs Open, f = fMAX(3) mA mA mA 2911 tbl 09b NOTES: 1. 'X' in part number indicates power rating (S or L) 2. VCC = 3.3V, TA = +25C, and are not production tested. ICC DC = 115mA (typ.) 3. At f = f MAX, address and control lines (except Output Enable) are cycling at the maximum frequency read cycle of 1/tRC, and using "AC Test Conditions" of input levels of GND to 3V. 4. f = 0 means no address or control lines change. 5. Port "A" may be either left or right port. Port "B" is the opposite from port "A". 6.42 6 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Test Conditions Input Pulse Levels 3.3V 3.3V GND to 3.0V Input Rise/Fall Times 3ns Max. Input Timing Reference Levels 1.5V Output Reference Levels 1.5V Output Load 590 590 DATAOUT BUSY INT Figures 1 and 2 DATAOUT 435 30pF 435 5pF* 2911 tbl 10 , 2911 drw 05 Figure 2. Output Test Load (for t LZ, tHZ, tWZ, tOW) * Including scope and jig. Figure 1. AC Output Test Load (for t LZ, tHZ, tWZ, tOW) Timing of Power-Up Power-Down CE ICC tPU tPD 50% 50% ISB 2911 drw 06 6.42 7 , IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(4) 70V24X15 Com'l Only Symbol Parameter 70V24X20 Com'l & Ind 70V24X25 Com'l & Ind Min. Max. Min. Max. Min. Max. Unit Read Cycle Time 15 ____ 20 ____ 25 ____ ns tAA Address Access Time ____ 15 ____ 20 ____ 25 ns tACE Chip Enable Access Time (3) ____ 15 ____ 20 ____ 25 ns tABE Byte Enable Access Time (3) ____ 15 ____ 20 ____ 25 ns tAOE Output Enable Access Time (3) ____ 10 ____ 12 ____ 13 ns tOH Output Hold from Address Change 3 ____ 3 ____ 3 ____ ns tLZ Output Low-Z Time(1,2) 3 ____ 3 ____ 3 ____ ns tHZ Output High-Z Time (1,2) ____ 10 ____ 12 ____ 15 ns tPU Chip Enable to Power Up Time (1,2) 0 ____ 0 ____ 0 ____ ns tPD Chip Disable to Power Down Time (1,2) ____ 15 ____ 20 ____ 25 ns tSOP Semaphore Flag Update Pulse (OE or SEM) 10 ____ 10 ____ 10 ____ ns tSAA Semaphore Address Access (3) ____ 15 ____ 20 ____ 25 READ CYCLE tRC ns 2911 tbl 11a 70V24X35 Com'l & Ind Symbol Parameter 70V24X55 Com'l & Ind Min. Max. Min. Max. Unit Read Cycle Time 35 ____ 55 ____ ns Address Access Time ____ READ CYCLE tRC 35 ____ 55 ns Chip Enable Access Time (3) ____ 35 ____ 55 ns tABE Byte Enable Access Time (3) ____ 35 ____ 55 ns tAOE Output Enable Access Time (3) ____ 20 ____ 30 ns tOH Output Hold from Address Change 3 ____ 3 ____ ns 3 ____ 3 ____ ns ____ 15 ____ 25 ns 0 ____ 0 ____ ns tAA tACE tLZ tHZ Output Low-Z Time (1,2) Output High-Z Time (1,2) (1,2) tPU Chip Enable to Power Up Time tPD Chip Disable to Power Down Time (1,2) ____ 35 ____ 50 ns tSOP Semaphore Flag Update Pulse (OE or SEM) 15 ____ 15 ____ ns 35 ____ 55 tSAA Semaphore Address Access (3) ____ NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with Output Test Load (Figure 2). 2. This parameter is guaranteed by device characterization, but is not production tested. 3. To access RAM, CE = VIL, UB or LB = VIL, and SEM = VIH. To access semaphore, CE = V IH or UB and LB = V IH, and SEM = VIL. 4. 'X' in part number indicates power rating (S or L). 6.42 8 ns 2911 tbl 11b IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Waveform of Read Cycles(5) tRC ADDR CE tAA (4) (4) tACE tAOE (4) OE (4) tABE UB , LB R/W tLZ DATAOUT tOH (1) (4) VALID DATA tHZ (2) BUSY OUT (3,4) tBDD 2911 drw 07 NOTES: 1. Timing depends on which signal is asserted last, OE, CE, LB, or UB. 2. Timing depends on which signal is de-asserted first CE, OE, LB, or UB. 3. tBDD delay is required only in cases where opposite port is completing a write operation to the same address location. For simultaneous read operations BUSY has no relation to valid output data. 4. Start of valid data depends on which timing becomes effective last tABE, tAOE, tACE, tAA or tBDD. 5. SEM = VIH. 6.42 9 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage(5) 70V24X15 Com'l Only Symbol Parameter 70V24X20 Com'l & Ind 70V24X25 Com'l & Ind Min. Max. Min. Max. Min. Max. Unit 15 ____ 20 ____ 25 ____ ns 12 ____ 15 ____ 20 ____ ns 12 ____ 15 ____ 20 ____ ns 0 ____ 0 ____ 0 ____ ns 12 ____ 15 ____ 20 ____ ns ns WRITE CYCLE tWC tEW tAW Write Cycle Time Chip Enable to End-of-Write Address Valid to End-of-Write Address Set-up Time tAS tWP (3) (3) Write Pulse Width tWR Write Recovery Time 0 ____ 0 ____ 0 ____ tDW Data Valid to End-of-Write 10 ____ 15 ____ 15 ____ ns ____ 10 ____ 12 ____ 15 ns 0 ____ 0 ____ 0 ____ ns ____ 10 ____ 12 ____ 15 ns 0 ____ 0 ____ 0 ____ ns 5 ____ 5 ____ 5 ____ ns 5 ____ 5 ____ 5 ____ Output High-Z Time tHZ Data Hold Time tDH (1,2) (4) (1,2) Write Enable to Output in High-Z tWZ tOW Output Active from End-of-Write tSWRD SEM Flag Write to Read Time tSPS SEM Flag Contention Window (1,2,4) ns 2911 tbl 12a 70V24X35 Com'l & Ind Symbol Parameter 70V24X55 Com'l & Ind Min. Max. Min. Max. Unit WRITE CYCLE tWC Write Cycle Time 35 ____ 55 ____ ns tEW Chip Enable to End-of-Write (3) 30 ____ 45 ____ ns tAW Address Valid to End-of-Write 30 ____ 45 ____ ns 0 ____ 0 ____ ns 25 ____ 40 ____ ns 0 ____ 0 ____ ns 15 ____ 30 ____ ns ____ 15 ____ 25 ns 0 ____ 0 ____ ns ____ tAS tWP tWR tDW tHZ tDH Address Set-up Time (3) Write Pulse Width Write Recovery Time Data Valid to End-of-Write Output High-Z Time Data Hold Time (1,2) (4) (1,2) tWZ Write Enable to Output in High-Z 15 ____ 25 ns tOW Output Active from End-of-Write (1,2,4) 0 ____ 0 ____ ns tSWRD SEM Flag Write to Read Time 5 ____ 5 ____ ns tSPS SEM Flag Contention Window 5 ____ 5 ____ ns 2911 tbl 12b NOTES: 1. Transition is measured 0mV from Low or High-impedance voltage with Output Test Load (Figure 2). 2. This parameter is guaranteed by device characterization, but is not production tested. 3. To access SRAM, CE = VIL, UB or LB = VIL, SEM = V IH. To access semaphore, CE = VIH or UB and LB = VIH and SEM = VIL. Either condition must be valid for the entire tEW time. 4. The specification for tDH must be met by the device supplying write data to the SRAM under all operating conditions. Although tDH and tOW values will vary over voltage and temperature, the actual tDH will always be smaller than the actual tOW . 5. 'X' in part number indicates power rating (S or L). 6.42 10 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Write Cycle No. 1, R/W Controlled Timing(1,5,8) tWC ADDRESS tHZ (7) OE tAW CE or SEM (9) CE or SEM (9) tAS (6) tWR (3) tWP (2) R/W tWZ (7) tOW (4) DATAOUT (4) tDW tDH DATAIN 2911 drw 08 Timing Waveform of Write Cycle No. 2, CE, UB, LB Controlled Timing(1,5) tWC ADDRESS tAW (9) CE or SEM tAS(6) UB or LB tWR (3) tEW (2) (9) R/W tDW tDH DATAIN 2911 drw 09 NOTES: 1. R/W or CE or UB & LB must be high during all address transitions. 2. A write occurs during the overlap (tEW or tWP) of a low UB or LB and a LOW CE and a LOW R/W for memory array writing cycle. 3. tWR is measured from the earlier of CE or R/W (or SEM or R/W) going HIGH to the end of write cycle. 4. During this period, the I/O pins are in the output state and input signals must not be applied. 5. If the CE or SEM LOW transition occurs simultaneously with or after the R/W LOW transition, the outputs remain in the high-impedance state. 6. Timing depends on which enable signal is asserted last, CE, R/W or byte control. 7. This parameter is guaranteed by device characterization, but is not production tested.Transition is measured 0mV from low or high-impedance voltage with Output Test Load (Figure 2). 8. If OE is LOW during R/W controlled write cycle, the write pulse width must be the larger of tWP or (tWZ + tDW) to allow the I/O drivers to turn off and data to be placed on the bus for the required tDW. If OE is HIGH during an R/W controlled write cycle, this requirement does not apply and the write pulse can be as short as the specified tWP. 9. To access SRAM, CE = VIL, UB or LB = VIL, SEM = VIH. To access semaphore, CE = VIH or UB and LB = VIH and SEM = VIL. Either condition must be valid for the entire tEW time. 6.42 11 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Semaphore Read after Write Timing, Either Side(1) tOH tSAA A0-A2 VALID ADDRESS tWR tAW tEW VALID ADDRESS tACE SEM tSOP tDW DATAIN VALID I/O0 tAS tWP DATAOUT VALID(2) tDH R/W tSWRD tAOE OE Write Cycle Read Cycle 2911 drw 10 NOTES: 1. CE = VIH or UB & LB = VIH for the duration of the above timing (both write and read cycle). 2. "DATAOUT VALID" represents all I/O's (I/O 0-I/O15)equal to the semaphore value. Timing Waveform of Semaphore Write Contention(1,3,4) A0"A"-A2"A" (2) SIDE "A" MATCH R/W"A" SEM"A" tSPS A0"B"-A2"B" (2) SIDE "B" MATCH R/W"B" SEM"B" 2911 drw 11 NOTES: 1. D0R = D0L = VIL, CER = CEL = VIH, or Both UB & LB = V IH. 2. All timing is the same for left or right port. "A" may be either left or right port. "B" is the opposite port from "A". 3. This parameter is measured from R/W"A" or SEM"A" going HIGH to R/W"B" or SEM"B" going HIGH. 4. If t SPS is not satisfied there is no guarantee which side will be granted the semaphore flag. 6.42 12 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Oemperature and Supply Voltage Range(6) 70V24X15 Com'l Ony Symbol Parameter 70V24X20 Com'l & Ind 70V24X25 Com'l & Ind Min. Max. Min. Max. Min. Max. Unit BUSY TIMING (M/S = VIH) tBAA BUSY Access Time from Address Match ____ 15 ____ 20 ____ 20 ns tBDA BUSY Disable Time from Address Not Matched ____ 15 ____ 20 ____ 20 ns tBAC BUSY Access Time from Chip Enable LOW ____ 15 ____ 20 ____ 20 ns tBDC BUSY Disable Time from Chip Enable HIGH ____ 15 ____ 17 ____ 17 ns tAPS Arbitration Priority Set-up Time (2) 5 ____ 5 ____ 5 ____ ns tBDD BUSY Disable to Valid Data(3) ____ 18 ____ 30 ____ 30 ns tWH Write Hold After BUSY 12 ____ 15 ____ 17 ____ ns 0 ____ 0 ____ 0 ____ ns 12 ____ 15 ____ 17 ____ ns (5) BUSY TIMING (M/S = VIL) tWB BUSY Input to Write(4) tWH Write Hold After BUSY (5) PORT-TO-PORT DELAY TIMING tWDD Write Pulse to Data Delay(1) ____ 30 ____ 45 ____ 50 ns tDDD Write Data Valid to Read Data Delay (1) ____ 25 ____ 35 ____ 35 ns 2911 tbl 13a 70V24X35 Com'l & Ind Symbol Parameter BUSY TIMING (M/S = 70V24X55 Com'l & Ind Min. Max. Min. Max. Unit VIH) tBAA BUSY Access Time from Address Match ____ 20 ____ 45 ns tBDA BUSY Disable Time from Address Not Matched ____ 20 ____ 40 ns tBAC BUSY Access Time from Chip Enable LOW ____ 20 ____ 40 ns tBDC BUSY Disable Time from Chip Enable HIGH ____ 20 ____ 35 ns 5 ____ 5 ____ ns ____ 35 ____ 40 ns 25 ____ 25 ____ ns tAPS Arbitration Priority Set-up Time tBDD BUSY Disable to Valid Data tWH Write Hold After BUSY (2) (3) (5) BUSY TIMING (M/S = VIL) tWB BUSY Input to Write (4) 0 ____ 0 ____ ns tWH Write Hold After BUSY(5) 25 ____ 25 ____ ns ____ 60 ____ 80 ns 45 ____ 65 ns PORT-TO-PORT DELAY TIMING tWDD tDDD Write Pulse to Data Delay (1) Write Data Valid to Read Data Delay (1) ____ 2911 tbl 13b NOTES: 1. Port-to-port delay through SRAM cells from writing port to reading port, refer to "Timing Waveform of Read With BUSY (M/S = VIH)" or "Timing Waveform of Write With Port-To-Port Delay (M/S = VIL)". 2. To ensure that the earlier of the two ports wins. 3. tBDD is a calculated parameter and is the greater of 0ns, tWDD - tWP (actual) or tDDD - tDW (actual). 4. To ensure that the write cycle is inhibited during contention. 5. To ensure that a write cycle is completed after contention. 6. 'X' in part number indicates power rating (S or L). 6.42 13 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Read with BUSY(2,4,5) (M/S = VIH) tWC MATCH ADDR"A" tWP R/W "A" tDW tDH VALID DATAIN "A" tAPS (1) MATCH ADDR"B" tBAA tBDA tBDD BUSY "B" tWDD DATAOUT "B" VALID tDDD (3) 2911 drw 12 NOTES: 1. To ensure that the earlier of the two ports wins. tAPS is ignored for M/S = VIL (slave). 2. CEL = CER = VIL. 3. OE = VIL for the reading port. 4. If M/S = VIL (slave), BUSY is an input. Then for this example BUSY "A" = VIH and BUSY"B" input is shown above. 5. All timing is the same for both left and right ports. Port "A" may be either the left or right Port. Port "B" is the port opposite from port "A". 6.42 14 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Timing Waveform of Slave Write (M/S = VIL) tWP R/W "A" tWB(3) BUSY "B" tWH(1) R/W "B" (2) 2911 drw 13 NOTES: 1. tWH must be met for both BUSY input (slave) and output (master). 2. Busy is asserted on port "B" blocking R/W"B", until BUSY "B" goes HIGH. 3. tWB is only for the "slave" version. Waveform of BUSY Arbitration Controlled by CE Timing(1) (M/S = VIH) ADDR"A" and "B" ADDRESSES MATCH CE"A" tAPS (2) CE"B" tBAC tBDC BUSY"B" 2911 drw 14 Waveform of BUSY Arbitration Cycle Controlled by Address Match Timing(1) (M/S = VIH) ADDR"A" ADDRESS "N" tAPS (2) ADDR"B" MATCHING ADDRESS "N" tBAA tBDA BUSY"B" 2911 drw 15 NOTES: 1. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from "A". 2. If tAPS is not satisfied, the BUSY signal will be asserted on one side or another but there is no guarantee on which side BUSY will be asserted. 6.42 15 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges AC Electrical Characteristics Over the Operating Temperature and Supply Voltage Range(1) 70V24X15 Com'l Only Symbol Parameter 70V24X20 Com'l & Ind 70V24X25 Com'l & Ind Min. Max. Min. Max. Min. Max. Unit INTERRUPT TIMING tAS Address Set-up Time 0 ____ 0 ____ 0 ____ ns tWR Write Recovery Time 0 ____ 0 ____ 0 ____ ns tINS Interrupt Set Time ____ 15 ____ 20 ____ 20 ns tINR Interrupt Reset Time ____ 15 ____ 20 ____ 20 ns 2911 tbl 14a 70V24X35 Com'l & Ind Symbol Parameter 70V24X55 Com'l & Ind Min. Max. Min. Max. Unit INTERRUPT TIMING tAS Address Set-up Time 0 ____ 0 ____ ns tWR Write Recovery Time 0 ____ 0 ____ ns tINS Interrupt Set Time ____ 25 ____ 40 ns Interrupt Reset Time ____ 25 ____ 40 tINR ns 2911 tbl 14b NOTES: 1. 'X' in part number indicates power rating (S or L). 6.42 16 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Waveform of Interrupt Timing(1) tWC ADDR"A" INTERRUPT SET ADDRESS (2) tAS (3) tWR (4) CE "A" R/W "A" tINS (3) INT "B" 2911 drw 16 tRC INTERRUPT CLEAR ADDRESS ADDR"B" (2) tAS (3) CE "B" OE "B" tINR(3) INT"B" 2911 drw 17 NOTES: 1. All timing is the same for left and right ports. Port "A" may be either the left or right port. Port "B" is the port opposite from "A". 2. See Interrupt Truth Table III. 3. Timing depends on which enable signal (CE or R/W) is asserted last. 4. Timing depends on which enable signal (CE or R/W) is de-asserted first. 6.42 17 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Truth Table III Interrupt Flag(1) Left Port CEL R/WL L OEL L Right Port INTL A11L-A0L X FFF CER R/W R X X X OE R A11R -A0R X INTR Function (2) Set Right INT R Flag (3) X L X X X X X X L L FFF H Reset Right INT R Flag X X X X L(3) L L X FFE X Set Left INT L Flag X L L FFE H(2) X X X X X Reset Left INT L Flag 2911 tbl 15 NOTES: 1. Assumes BUSY L = BUSYR = VIH. 2. If BUSYL = VIL, then no change. 3. If BUSYR = VIL, then no change. Truth Table IV Address BUSY Arbitration Inputs Outputs CEL CER A0L-A11L A0R-A11R BUSYL(1) BUSYR(1) Function X X NO MATCH H H Normal H X MATCH H H Normal X H MATCH H H Normal L L MATCH (2) (2) Write Inhibit(3) 2911 tbl 16 NOTES: 1. Pins BUSY L and BUSYR are both outputs when the part is configured as a master. Both are inputs when configured as a slave. BUSY outputs on the IDT70V24 are push pull, not open drain outputs. On slaves the BUSY input internally inhibits writes. 2. L if the inputs to the opposite port were stable prior to the address and enable inputs of this port. V IH if the inputs to the opposite port became stable after the address and enable inputs of this port. If tAPS is not met, either BUSY L or BUSYR = LOW will result. BUSYL and BUSYR outputs cannot be LOW simultaneously. 3. Writes to the left port are internally ignored when BUSYL outputs are driving LOW regardless of actual logic level on the pin. Writes to the right port are internally ignored when BUSY R outputs are driving LOW regardless of actual logic level on the pin. Truth Table V Example of Semaphore Procurement Sequence(1,2,3) Functions D0 - D15 Left D0 - D15 Right Status No Action 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Right Port Writes "0" to Semaphore 0 1 No change. Right side has no write access to semaphore Left Port Writes "1" to Semaphore 1 0 Right port obtains semaphore token Left Port Writes "0" to Semaphore 1 0 No change. Left port has no write access to semaphore Right Port Writes "1" to Semaphore 0 1 Left port obtains semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free Right Port Writes "0" to Semaphore 1 0 Right port has semaphore token Right Port Writes "1" to Semaphore 1 1 Semaphore free Left Port Writes "0" to Semaphore 0 1 Left port has semaphore token Left Port Writes "1" to Semaphore 1 1 Semaphore free 2911 tbl 17 NOTES: 1. This table denotes a sequence of events for only one of the eight semaphores on the IDT70V24. 2. There are eight semaphore flags written to via I/O 0 and read from all I/O's (I/O0-I/O15 ). These eight semaphores are addressed by A0-A2. 3. CE = VIH, SEM = VIL to access the semaphores. Refer to the Semaphore Read/Write Control Truth Table. 6.42 18 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM BUSYL MASTER Dual Port SRAM BUSYL BUSYL CE SLAVE Dual Port SRAM BUSYR BUSYL CE SLAVE Dual Port SRAM BUSYL BUSYR CE BUSYR DECODER MASTER Dual Port SRAM Industrial and Commercial Temperature Ranges CE BUSYR BUSYR 2911 drw 18 Figure 3. Busy and chip enable routing for both width and depth expansion with IDT70V24 SRAMs. Functional Description The IDT70V24 provides two ports with separate control, address and I/O pins that permit independent access to any location in memory. The IDT70V24 has an automatic power down feature controlled by CE. The CE controls on-chip power down circuitry that permits the respective port to go into a standby mode when not selected (CE HIGH). When a port is enabled, access to the entire memory array is permitted. Interrupts If the user chooses the interrupt function, a memory location (mail box or message center) is assigned to each port. The left port interrupt flag (INTL) is asserted when the right port writes to memory location FFE (HEX), where a write is defined as the CE=R/W=VIL per Truth Table III. The left port clears the interrupt by accessing address location FFE when CER = OER = VIL, R/W is a "don't care". Likewise, the right port interrupt flag (INTR) is asserted when the left port writes to memory location FFF (HEX) and to clear the interrupt flag (INTR), the right port must read the memory location FFF. The message (16 bits) at FFE or FFF is user-defined, since it is an addressable SRAM location. If the interrupt function is not used, address locations FFE and FFF are not used as mail boxes, but as part of the random access memory. Refer to Truth Table IIII for the interrupt operation. Busy Logic Busy Logic provides a hardware indication that both ports of the SRAM have accessed the same location at the same time. It also allows one of the two accesses to proceed and signals the other side that the SRAM is "busy". The BUSY pin can then be used to stall the access until the operation on the other side is completed. If a write operation has been attemp-ted from the side that receives a BUSY indication, the write signal is gated internally to prevent the write from proceeding. The use of BUSY logic is not required or desirable for all applications. In some cases it may be useful to logically OR the BUSY outputs together and use any BUSY indication as an interrupt source to flag the event of an illegal or illogical operation. If the write inhibit function of BUSY logic is not desirable, the BUSY logic can be disabled by placing the part in slave mode with the M/S pin. Once in slave mode the BUSY pin operates solely as a write inhibit input pin. Normal operation can be programmed by tying the BUSY pins HIGH. If desired, unintended write operations can be prevented to a port by tying the BUSY pin for that port LOW. The busy outputs on the IDT 70V24 SRAM in master mode, are pushpull type outputs and do not require pull up resistors to operate. If these RAMs are being expanded in depth, then the BUSY indication for the resulting array requires the use of an external AND gate. Width Expansion with BUSY Logic Master/Slave Arrays When expanding an IDT70V24 SRAM array in width while using busy logic, one master part is used to decide which side of the SRAM array will receive a BUSY indication, and to output that indication. Any number of slaves to be addressed in the same address range as the master, use the BUSY signal as a write inhibit signal. Thus on the IDT70V24 SRAM the BUSY pin is an output if the part is used as a master (M/S pin = VIH), and the BUSY pin is an input if the part used as a slave (M/S pin = VIL) as shown in Figure 3. If two or more master parts were used when expanding in width, a split decision could result with one master indicating BUSY on one side of the array and another master indicating BUSY on one other side of the array. This would inhibit the write operations from one port for part of a word and inhibit the write operations from the other port for the other part of the word. The BUSY arbitration, on a master, is based on the chip enable and address signals only. It ignores whether an access is a read or write. In a master/slave array, both address and chip enable must be valid long enough for a BUSY flag to be output from the master before the actual write pulse can be initiated with either the R/W signal or the byte enables. Failure to observe this timing can result in a glitched internal write inhibit signal and corrupted data in the slave. Semaphores The IDT70V24 is an extremely fast Dual-Port 4K x 16 CMOS Static RAM with an additional 8 address locations dedicated to binary semaphore flags. These flags allow either processor on the left or right side of the Dual-Port SRAM to claim a privilege over the other processor for functions defined by the system designer's software. As an example, the semaphore can be used by one processor to inhibit the other from accessing a portion of the Dual-Port SRAM or any other shared resource. 6.42 19 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges The Dual-Port SRAM features a fast access time, and both ports are completely independent of each other. This means that the activity on the left port in no way slows the access time of the right port. Both ports are identical in function to standard CMOS Static RAM and can be accessed to, at the same time with the only possible conflict arising from the simultaneous writing of, or a simultaneous READ/WRITE of, a nonsemaphore location. Semaphores are protected against such ambiguous situations and may be used by the system program to avoid any conflicts in the non-semaphore portion of the Dual-Port SRAM. These devices have an automatic power-down feature controlled by CE, the Dual-Port SRAM enable, and SEM, the semaphore enable. The CE and SEM pins control on-chip power down circuitry that permits the respective port to go into standby mode when not selected. This is the condition which is shown in Truth Table I where CE and SEM are both HIGH. Systems which can best use the IDT70V24 contain multiple processors or controllers and are typically very high-speed systems which are software controlled or software intensive. These systems can benefit from a performance increase offered by the IDT70V24's hardware semaphores, which provide a lockout mechanism without requiring complex programming. Software handshaking between processors offers the maximum in system flexibility by permitting shared resources to be allocated in varying configurations. The IDT70V24 does not use its semaphore flags to control any resources through hardware, thus allowing the system designer total flexibility in system architecture. An advantage of using semaphores rather than the more common methods of hardware arbitration is that wait states are never incurred in either processor. This can prove to be a major advantage in very high-speed systems. How the Semaphore Flags Work The semaphore logic is a set of eight latches which are independent of the Dual-Port SRAM. These latches can be used to pass a flag, or token, from one port to the other to indicate that a shared resource is in use. The semaphores provide a hardware assist for a use assignment method called "Token Passing Allocation." In this method, the state of a semaphore latch is used as a token indicating that shared resource is in use. If the left processor wants to use this resource, it requests the token by setting the latch. This processor then verifies its success in setting the latch by reading it. If it was successful, it proceeds to assume control over the shared resource. If it was not successful in setting the latch, it determines that the right side processor has set the latch first, has the token and is using the shared resource. The left processor can then either repeatedly request that semaphore's status or remove its request for that semaphore to perform another task and occasionally attempt again to gain control of the token via the set and test sequence. Once the right side has relinquished the token, the left side should succeed in gaining control. The semaphore flags are active LOW. A token is requested by writing a zero into a semaphore latch and is released when the same side writes a one to that latch. The eight semaphore flags reside within the IDT70V24 in a separate memory space from the Dual-Port SRAM. This address space is accessed by placing a LOW input on the SEM pin (which acts as a chip select for the semaphore flags) and using the other control pins (Address, OE, and R/W) as they would be used in accessing a standard Static RAM. Each of the flags has a unique address which can be accessed by either side through address pins A0 - A2. When accessing the semaphores, none of the other address pins has any effect. When writing to a semaphore, only data pin D0 is used. If a LOW level is written into an unused semaphore location, that flag will be set to a zero on that side and a one on the other side (see Truth Table V). That semaphore can now only be modified by the side showing the zero. When a one is written into the same location from the same side, the flag will be set to a one for both sides (unless a semaphore request from the other side is pending) and then can be written to by both sides. The fact that the side which is able to write a zero into a semaphore subsequently locks out writes from the other side is what makes semaphore flags useful in interprocessor communications. (A thorough discussion on the use of this feature follows shortly.) A zero written into the same location from the other side will be stored in the semaphore request latch for that side until the semaphore is freed by the first side. When a semaphore flag is read, its value is spread into all data bits so that a flag that is a one reads as a one in all data bits and a flag containing a zero reads as all zeros. The read value is latched into one side's output register when that side's semaphore select (SEM) and output enable (OE) signals go active. This serves to disallow the semaphore from changing state in the middle of a read cycle due to a write cycle from the other side. Because of this latch, a repeated read of a semaphore in a test loop must cause either signal (SEM or OE) to go inactive or the output will never change. A sequence WRITE/READ must be used by the semaphore in order to guarantee that no system level contention will occur. A processor requests access to shared resources by attempting to write a zero into a semaphore location. If the semaphore is already in use, the semaphore request latch will contain a zero, yet the semaphore flag will appear as one, a fact which the processor will verify by the subsequent read (see Truth Table V). As an example, assume a processor writes a zero to the left port at a free semaphore location. On a subsequent read, the processor will verify that it has written successfully to that location and will assume control over the resource in question. Meanwhile, if a processor on the right side attempts to write a zero to the same semaphore flag it will fail, as will be verified by the fact that a one will be read from that semaphore on the right side during subsequent read. Had a sequence of READ/WRITE been used instead, system contention problems could have occurred during the gap between the read and write cycles. It is important to note that a failed semaphore request must be followed by either repeated reads or by writing a one into the same location. The reason for this is easily understood by looking at the simple logic diagram of the semaphore flag in Figure 4. Two semaphore request latches feed into a semaphore flag. Whichever latch is first to present a zero to the semaphore flag will force its side of the semaphore flag LOW and the other side HIGH. This condition will continue until a one is written to the same semaphore request latch. Should the other side's semaphore request latch have been written to a zero in the meantime, the semaphore flag will flip over to the other side as soon as a one is written into the first side's request latch. The second side's flag will now stay LOW until its semaphore request latch is written to a one. From this it is easy to understand that, if a semaphore is requested and the processor which requested it no longer needs the resource, the entire system can hang up until a one is written into that semaphore request 6.42 20 IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges latch. The critical case of semaphore timing is when both sides request a single token by attempting to write a zero into it at the same time. The semaphore logic is specially designed to resolve this problem. If simultaneous requests are made, the logic guarantees that only one side receives the token. If one side is earlier than the other in making the request, the first side to make the request will receive the token. If both requests arrive at the same time, the assignment will be arbitrarily made to one port or the other. One caution that should be noted when using semaphores is that semaphores alone do not guarantee that access to a resource is secure. As with any powerful programming technique, if semaphores are misused or misinterpreted, a software error can easily happen. Initialization of the semaphores is not automatic and must be handled via the initialization program at power-up. Since any semaphore request flag which contains a zero must be reset to a one, all semaphores on both sides should have a one written into them at initialization from both sides to assure that they will be free when needed. Using SemaphoresSome Examples Perhaps the simplest application of semaphores is their application as resource markers for the IDT70V24's Dual-Port SRAM. Say the 4K x 16 SRAM was to be divided into two 2K x 16 blocks which were to be dedicated at any one time to servicing either the left or right port. Semaphore 0 could be used to indicate the side which would control the lower section of memory, and Semaphore 1 could be defined as the indicator for the upper section of memory. To take a resource, in this example the lower 2K of Dual-Port SRAM, the processor on the left port could write and then read a zero in to Semaphore 0. If this task were successfully completed (a zero was read back rather than a one), the left processor would assume control of the lower 2K. Meanwhile the right processor was attempting to gain control of the resource after the left processor, it would read back a one in response to the zero it had attempted to write into Semaphore 0. At this point, the software could choose to try and gain control of the second 2K section by writing, then reading a zero into Semaphore 1. If it succeeded in gaining control, it would lock out the left side. Once the left side was finished with its task, it would write a one to Semaphore 0 and may then try to gain access to Semaphore 1. If Semaphore 1 was still occupied by the right side, the left side could undo its semaphore request and perform other tasks until it was able to write, then read a zero into Semaphore 1. If the right processor performs a similar task with Semaphore 0, this protocol would allow the two processors to swap 2K blocks of Dual-Port SRAM with each other. The blocks do not have to be any particular size and can even be variable, depending upon the complexity of the software using the semaphore flags. All eight semaphores could be used to divide the Dual-Port SRAM or other shared resources into eight parts. Semaphores can even be assigned different meanings on different sides rather than being given a common meaning as was shown in the example above. Semaphores are a useful form of arbitration in systems like disk interfaces where the CPU must be locked out of a section of memory during a transfer and the I/O device cannot tolerate any wait states. With the use of semaphores, once the two devices has determined which memory area was "off-limits" to the CPU, both the CPU and the I/O devices could access their assigned portions of memory continuously without any wait states. Semaphores are also useful in applications where no memory "WAIT" state is available on one or both sides. Once a semaphore handshake has been performed, both processors can access their assigned SRAM segments at full speed. Another application is in the area of complex data structures. In this case, block arbitration is very important. For this application one processor may be responsible for building and updating a data structure. The other processor then reads and interprets that data structure. If the interpreting processor reads an incomplete data structure, a major error condition may exist. Therefore, some sort of arbitration must be used between the two different processors. The building processor arbitrates for the block, locks it and then is able to go in and update the data structure. When the update is completed, the data structure block is released. This allows the interpreting processor to come back and read the complete data structure, thereby guaranteeing a consistent data structure. L PORT R PORT SEMAPHORE REQUEST FLIP FLOP D0 WRITE D SEMAPHORE REQUEST FLIP FLOP Q Q SEMAPHORE READ D D0 WRITE SEMAPHORE READ 2911 drw 19 Figure 4. IDT70V24 Semaphore Logic 6.42 21 , IDT70V24S/L High-Speed 4K x 16 Dual-Port Static RAM Industrial and Commercial Temperature Ranges Ordering Information IDT XXXXX Device Type A 999 A A Power Speed Package Process/ Temperature Range Blank I Commercial (0C to +70C) Industrial (-40C to +85C) PF G J 100-pin TQFP (PN100-1) 84-pin PGA (G84-3) 84-pin PLCC (J84-1) 15 20 25 35 55 Commercial Only Commercial & Industrial Commercial & Industrial Commercial & Industrial Commercial & Industrial S L Standard Power Low Power Speed in nanoseconds 70V24 64K (4K x 16) 3.3V Dual-Port RAM 2911 drw 20 Datasheet Document History 3/8/99: 6/10/99: 8/1/99: 8/30/99: 11/12/99: 3/10/00: Initiated datasheet document history Converted to new format Cosmetic and typographical corrections Pages 2 and 3 Added additional notes to pin configurations Changed drawing format Page 2 TQFP for corrected pinout (no pin 55 was shown) Page 1 Changed 660mW to 660W Replaced IDT logo Added 15 and 20ns speed grades Upgraded DC parameters Added Industrial Temperature information Changed 200 mV to 0mV in notes CORPORATE HEADQUARTERS 2975 Stender Way Santa Clara, CA 95054 for SALES: 800-345-7015 or 408-727-6116 fax: 408-492-8674 www.idt.com The IDT logo is a registered trademark of Integrated Device Technology, Inc. 6.42 22 for Tech Support: 831-754-4613 DualPortHelp@idt.com