P
Design and Specications are subject to change without notice. Ask the factory for technical specications before purchase and/or use. If there is any doubt
regarding the safety of this product, kindly inform us immediately for technical consultation. PAN1555 Rev. B1
www.pedeu.panasonic.de
wireless@eu.panasonic.com
WIRELESS
MODULES
Panasonic Electronic Devices Europe GmbH
Now you can integrate Bluetooth very easy in your nal
product, without qualication – with the PAN1555.
This solution follows the national and international
regulations, e.g. CE (Radio, EMC, Safety), FCC and IC.
The PAN1555 is manufactured in a 13.50 x 22.75 x 2.85 mm³
SMD package with an integrated ceramic antenna or plug and
will be qualied as a Bluetooth 2.0 product.
Re-qualication of your product is usually not required.
This is why the PAN1555 is particularly suited for units
produced in smaller or medium quantities.
This module is a one to one replacement for the well known
PAN1550.
Any customizations for the software can be handled with
our recommended partners.
General
- Complete Bluetooth 2.0 + EDR solution
- Full product qualication (Bluetooth, CE, FCC, IC)
- Proles: GAP, SDAP, SPP, HID and HDP available, other could
be supported on request.
- CSR BlueCore6-ROM inside
- Cortex-M3 ST32F103 core for embedded proles or
application software
- Temperature Range from -40°C to +85°C
- Supply Voltage Range from 2.7V to 3.6V, typ. 3.3V
- Fast Connection Setup
- Support for 802.11 Coexistence
Interfaces
- UART (programmable baud rate), USB, I²C, SPI and ADC
- 18 GPIOs for individual usage for your embedded software
- All bluetooth data rate up to 2178kbps asymmetric
- PCM Interface Master / Slave supporting 13 or 16 bit linear,
8 bit µ-law or A-law Codecs and CVSD transcoders on up to
3 SCO channels.
Bluetooth
- High Sensitivity Design (typ. -86 dBm)
- Full 8- to 128-bit encryption
- Power control and RSSI, Hold-, Park- and Sniffmode
- Support for very low power modes - sleep and deep sleep
OUTLINES - ENW89815A3KF
FEATURES
Bluetooth V2.0 Embedded
PAN1555-EMB-2.0
Cut the Cable TM
Hardware Status:
Mass Production
P
www.pedeu.panasonic.de
wireless@eu.panasonic.com
CONTACT
Dipl.-Ing.
Ingo Wagner
Product Engineer
Module Business
Panasonic Electronic Devices Europe GmbH
Zeppelinstrasse 19
21337 Lüneburg, Germany
Tel. (49)-4131-899-173
Fax (49)-4131-899-177
Ingo.Wagner@eu.panasonic.com
Parameter Value Condition / Note
Receiver Sensitivity (BER=10-3) -86 dBm typ. ideal wanted signal
Output Power +4 dBm typ.
Power Supply 2,7 - 3,6 V Single operation voltage
Ultra Low Power Mode <100 µA T = 25°C
ACL (connected DH5) 50.5mA to 49.5mA max. power to min. power (1)
ACL (connected DH1) 48.0mA to 46.0mA max. power to min. power (1)
Operating Temperature Range -40°C to +85°C Storage until +125°C
(1) Figure indicates to the shortest poll period and to the slave mode
All Embedded Wireless Applications
- Printer Adapters
- Printers
- Access Points
- Wireless Sensors
- Industrial Applications
- Cable Replacement
- Personal Digital Assistants (PDAs)
- Personal Navigation Devices
- Medical Applications
BLOCK-DIAGRAM
TECHNICAL CHARACTERISTICS
APPLICATIONS








































Hardware Status:
Mass Production