V23836-C18-R363 - Finisar Corporation

Product Specification

1x9 RoHS Compliant Transceiver with Duplex SC Receptacle

Single Mode 1310 nm 21 km SONET OC-3/SDH STM-1

V23836-C18-R363

PRODUCT FEATURES

 Compliant with ATM, SONET

OC-3, SDH STM-1

 Industry standard multisource 1x9

footprint

 Meets mezzanine standard height

of 9.8mm

 Compact integrated transceiver unit

with

- FP (Fabry Perot) laser diode

transmitter

- InGaAs PIN photodiode –

TIA receiver

- Duplex SC receptacle

 Standard operating temperature

range of 0°C to 70°C

 Class 1 FDA and IEC laser safety

compliant

 Single power supply (3.3 V)

 Signal detect indicator (PECL)

 PECL differential (DC-coupled)

inputs and outputs

 Process plug included

 Input Signal Monitor

 Wave solderable and washable

with process plug inserted

 For distances of up to 21 km on

single mode fiber

 1x9 evaluation board V23806-S84-

Z5 available upon request

PRODUCT SELECTION

Part Number Voltage

V23836-C18-R363 3.3 V

APPLICATIONS

 SONET OC-3 IR-1

Telcordia GR-253-CORE

 SDH STM-1 S-1.1 ITU-T G.957

 Suitable for Fast Ethernet

V23836-C18-R363 Product Specification – October 2006

Pin Configuration

Figure 1

Pin Description

Pin No. Symbol Level/Logic Function Description

1 VEERx Power Supply Rx Ground Negative power supply,

normally ground

2 RD+ Receiver output data

3 RD–

PECL Output Rx Output Data Inverted receiver output data

4 SD PECL Rx Signal Detect

A high level on this output

shows that optical data is

applied to the optical input.

5 VCCRx Rx 3.3 V

6 VCCTx Power Supply Tx 3.3 V

Positive power supply,

3.3 V

7 TD– Inverted transmitter input data

8 TD+

PECL Input Tx Input Data Transmitter input data

9 VEETx Power Supply Tx Ground Negative power supply,

normally ground

S1/2 Mech. Support Stud Pin Not connected

V23836-C18-R363 Product Specification – October 2006

DESCRIPTION

The Finisar single mode ATM transceiver complies with the ATM Forum’s Network

Compatible ATM for Local Network Applications document and ANSI’s Broadband

ISDN-Customer Installation Interfaces, Physical Media Dependent Specification,

T1.646-1995, Bellcore - SONET OC-3 IR-1 and ITU-T G.957 STM-1 S-1.1.

SUPPORTED LINK LENGTHS Reach

Category within Standard min. max.1) Unit

SDH STM S-1.1 0 15,000

SONET OC-3 IR-1 0 21,000 meters

Notes:

1) Maximum reach over fiber type SM-G.652 as defined by ITU-T G.957 and Telcordia GR-253-CORE

standards. Longer reach possible depending upon link implementation.

ATM was developed to facilitate solutions in multimedia applications and real time

transmission. The data rate is scalable, and the ATM protocol is the basis of the

broadband public networks being standardized in the International Telecommunications

Union (ITU), the former International Telegraph and Telephone Consultative Committee

(CCITT). ATM can also be used in local private applications.

The Finisar single mode ATM transceiver is a single unit comprised of a transmitter, a

receiver, and an SC receptacle. This design frees the customer from many alignment and

PC board layout concerns. The module is designed for low cost WAN applications. It can

be used as the network end device interface in workstations, servers, and storage devices,

and in a broad range of network devices such as bridges, routers, and intelligent hubs, as

well as wide area ATM switches.

This transceiver operates at 155.520Mbit/s from a single power supply. The differential

data inputs and outputs are DC-coupled and PECL compatible.

V23836-C18-R363 Product Specification – October 2006

FUNCTIONAL DESCRIPTION

This transceiver is designed to transmit serial data via single mode fiber.

Figure 2 Functional Diagram

The receiver component converts the optical serial data into PECL compatible electrical

data (RD+ and RD–). The Signal Detect (SD, active high) shows whether optical data

is present1).

The transmitter converts electrical PECL compatible serial data (TD+ and TD–) into

optical serial data.

The transmitter contains a laser driver circuit that drives the modulation and bias

currentof the laser diode. The currents are controlled by a power control circuit to

guarantee constant output power of the laser over temperature and aging.

The power control uses the output of the monitor PIN diode (mechanically built into the

laser coupling unit) as a controlling signal, to prevent the laser power from exceeding the

operating limits.

Single fault condition is ensured by means of an integrated automatic shutdown circuit

that disables the laser when it detects transmitter failures or when VCC is too high. A reset

is only possible by turning the power off, and then on again.

Notes:

1) We recommend to switch off the transmitter supply (VCCTx) if no transmitter input data is applied

V23836-C18-R363 Product Specification – October 2006

Regulatory Compliance

Feature Standard Comments

ESD:

Electrostatic Discharge

to the Electrical Pins

MIL-STD 883D

Method 3015.7

JESD22-A114-B

Class 1 (> 1000 V) HBM

Class 1C

Immunity:

Electrostatic Discharge

(ESD) to the Duplex

SC Receptacle

EN 61000-4-2I

EC 61000-4-2

Discharges of ±15 kV with an air

discharge probe on the receptacle

cause no damage

Immunity:

Radio Frequency

Electromagnetic Field

EN 61000-4-3

IEC 61000-4-3

With a field strength of 3 V/m, noise

frequency ranges from 10MHz to

2GHz. No effect on transceiver

performance between the

specification limits.

Emission:

Electromagnetic

Interference (EMI)

FCC 47 CFR Part 15

Class B EN 55022

Class B CISPR 22

Noise frequency range:

30MHz to 18GHz;

Margins depend on PCB layout

and chassis design.

V23836-C18-R363 Product Specification – October 2006

TECHNICAL DATA

Absolute Maximum Ratings

Limit Values

Parameter Symbol

min. max.

Unit

Package Power Dissipation1)

0.9 W

Supply Voltage

VCC–VEE 5 V

Data Input Levels VCC+0.5 V

Differential Data Input Voltage Swing VIDpk-pk 5 V

Operating Ambient Temperature 0 70 °C

Storage Ambient Temperature –40 85 °C

Soldering Conditions Temp/Time

(MIL-STD 883C, Method 2003)

250/10 ºC/s

Notes:

1) For VCC–VEE (min., max.). 50% duty cycle. The supply current does not include the load drive current of the receiver output.

Exceeding any one of these values may permanently destroy the device.

V23836-C18-R363 Product Specification – October 2006

Recommended Operating Conditions

Values

Parameter Symbol

min. typ. Max.

Unit

Ambient Temperature TAMB 0 70 °C

Power Supply Voltage

VCC–VEE 3.15 3.3 3.6 V

Supply Current1)

5 V

3.3 V

ICC

200

150

250

mA

Transmitter

Data Input High Voltage DC/DC VIH–VCC –1100 –740 mV

Data Input Low Voltage DC/DC VIL–VCC –2000 –1580 mV

Input Data Rise/Fall Time

10% - 90%

tR, tF 0.4 1.3 ns

Receiver

Input Center Wavelength λC 1100 1600 nm

Notes:

1) For VCC–VEE (min., max.) 50% duty cycle. The supply current does not include the load drive current of the receiver output.

The electro-optical characteristics described in the following tables are only valid for

useunder the recommended operating conditions.

Transmitter Electro-Optical Characteristics

Values Parameter Symbol min. typ. max.

Unit

Launched Power (Average)1) PO –15 –8 dBm

Center Wavelength λC 1260 1360 nm

Spectral Width (RMS) σI 7.7 nm μ

Extinction Ratio (Dynamic) ER 8.2 dB

Reset Threshold2) VTH 2.7 2.9 V

Eye Diagram3) ED Compliant

Notes:

1) Into single mode fiber, 9µm diameter

2) Laser power is shut down if power supply is below VTH min. and switched on if power supply is above VTH max.

3) Transmitter meets ANSI T1E1.2, SONET OC-3 and ITU-T G.957 mask patterns.

V23836-C18-R363 Product Specification – October 2006

Receiver Electro-Optical Characteristics

Values

Parameter Symbol

min. typ. max.

Unit

Sensitivity (Average Power)1)

5 V

3.3 V

–36

–28

–31

dBm

Saturation (Average Power) PSAT –8 dBm

Signal Detect Assert Level2) PSDA –34 dBm

Signal Detect Deassert Level3) PSDD –44 dBm

Signal Detect Hysteresis PSDA–PSDD 1 2 5 dB

Signal Detect Assert Time tASS 75 100 µs

Signal Detect Deassert Time tDAS 80 350 µs

Output Low Voltage4) VOL–VCC –2000 –1580 mV

Output High Voltage4) VOH–VCC –1100 –740 mV

Output Data Rise/Fall Time, 20% - 80% tR, tF 1.6 ns

Output SD Rise/Fall Time 10 40 ns

Notes:

1) Minimum average optical power at which the BER is less than 1x10–10 or lower. Measured with a 223–1 NRZPRBS as

recommended by ANSI T1E1.2, SONET OC-3 and ITU-T G.957. BOL value –31 dBm max.

2) An increase in optical power of data signal above the specified level will cause the Signal Detect to switch from a low state to a

high state.

3) A decrease in optical power of data signal below the specified level will cause the Signal Detect to switch froma high state to a low

state.

4) DC/DC, PECL for Signal Detect, PECL compatible. Load is 50Ω into VCC–2 V for data, 510 Ω to VEE for SignalDetect. Measured

under DC conditions. For dynamic measurements a tolerance of 50 mV should be added.VCC = 3.3 V. TAMB = 25°C.

V23836-C18-R363 Product Specification – October 2006

Eye Safety

This laser based single mode transceiver is a Class 1 product. It complies with IEC

60825-1/A2: 2001 and FDA performance standards for laser products (21 CFR 1040.10

and 1040.11) except for deviations pursuant to Laser Notice 50, dated July 26, 2001.

CLASS 1 LASER PRODUCT

To meet laser safety requirements the transceiver shall be operated within the

AbsoluteMaximum Ratings.

Note: All adjustments have been made at the factory prior to shipment of the devices.

No maintenance or alteration to the device is required.

Tampering with or modifying the performance of the device will result in voided

product warranty.

Failure to adhere to the above restrictions could result in a modification that is

considered an act of “manufacturing”, and will require, under law, recertification

of the modified product with the U.S. Food and Drug Administration (ref. 21 CFR

1040.10 (i)).

Laser Emission Data

Wavelength 1310 nm

Maximum total output power

(as defined by IEC: 7mm aperture at 14mm distance) 15.6 mW / 11.9 dBm

Beam divergence (full angle) / NA (half angle) 11° / 0.1 rad

Figure 3 Required Labels

Figure 4 Laser Emmission

V23836-C18-R363 Product Specification – October 2006

Application Notes

ATM transceivers and matching circuits are high frequency components and shall be

terminated as recommended in the application notes for proper EMI performance.

Electromagnetic emission may be caused by these components.

To prevent emissions it is recommended that cutouts for the fiber connectors be designed

as small as possible.

It is recommended that the Tx plug and the Rx plug be separated with a bar that divides

the duplex SC opening.

Single Mode 155 Mbit/s ATM 1x9 Transceiver, DC/DC PECL Version

Figure 5

V23836-C18-R363 Product Specification – October 2006

This application note assumes Fiber Optic transceivers using 3.3V power supply and

SerDes Chips using either 3.3V or 5V power supply. It also assumes no self biasing at the

receiver data inputs (RD+/RD–) of the SerDes chip (Refer to the manufacturer Product

Specification for other applications).

Value of R1...R4 may vary as long as proper 50Ω termination to VEE or 100Ω

differential is provided. The power supply filtering is required for good EMI

performance. Use short tracks from the inductor L1/L2 to the module VCCRx/VCCTx.

Further application notes for electrical interfacing are available upon request. Ask for

Appnote 82.

We strongly recommend a VEE plane under the module for getting good EMI

performance.

The transceiver contains an automatic shutdown circuit. Reset is only possible if the

power is turned off, and then on again. (VCCTx switched below VTH).

V23836-C18-R363 Product Specification – October 2006

Package Outlines

Figure 6

V23836-C18-R363 Product Specification – October 2006

For More Information

Finisar Corporation

1389 Moffett Park Drive

Sunnyvale, CA 94089-1133

Tel. 1-408-548-1000

Fax 1-408-541-6138

sales@finisar.com

www.finisar.com