DS460S-3-002 - Artesyn Embedded Technologies

POWER

DS460S

460 Watts

Total Output Power: 460 Watts

+12 Vdc Stand-by Output

Wide Range Input Voltage:

90 - 264 Vac

SPECIAL FEATURES

Active power factor correction

EN61000-3-2 harmonic compliance

Active AC inrush control

1U X 2U form factor

+12 Vdc output

+12 Vdc stand-by

Hot plug operation

N + 1 redundant

Active current sharing

Built-in cooling fan

I2C communication interface bus

PMBus compliant

EEPROM for FRU data

Two years warranty

SAFETY

UL/cUL 60950 (UL Recognized)

NEMKO 60950

Cb Certicate and report

CE Mark (LVD)

Electrical Specications

Input

Input ra nge: 90 - 264 Vac

Frequency: 47 - 63 Hz, single phase AC

Inrush current: 30 Apk maximum inrush current

Efﬁciency: 92% typical at high line 50% load

Conducted EMI: FCC Subpart J EN55022 Class A

Radiated EMI: FCC Subpart J EN55022 Class A

Power factor: 0.99 typical

Leakage current: 1.0 mA @ 240 Vac

Hold up time: 10 ms minimum

Output

Main DC voltage: +12.3 V @ 36.0 A

Stand-By: +12 V @ 2.3 A

Adjustment range: Factory Set

Regulation: 11.85 - 12.45 Vdc

11.40 - 12.6 Vdc

Overcurrent: +12 Vdc; latches off if overcurrent lasts over 1 second,

Trip point 120% - 150% of rated current.

Overvoltage: +12 Vdc; 13.6 - 15.0 Vdc

+12 Vsb; 13.6 - 15.0 Vdc

Turn-on delay: 1 - 1.5 seconds

Main output rise time: 10 - 30 mS, monotonic rise

Data Sheet

DS460S Data Sheet

Logic Control

PS_PRESENT (S4):

Used to sense the number of power supplies in the system (operational or not) and provide hot plug insertion and

removal functionality by controlling main outputs during hot plug insertion and removal by employing following

circuitry. When the unit is removed from the system the fast shut down signal quickly turns OFF main outputs and

discharges output capacitors. This signal is the shortest gold ﬁnger pin on the signal connector to allow for last

make, ﬁrst break conﬁguration.

PSOK (S6): Combined indicator of AC input and main 12 V DC output. This is a three level signal to indicate different stages

as follows.

AC not OK and DC not OK – Signal status shall be LOW (< 0.6 V)

AC OK and DC not OK – Signal status shall be LOW (< 0.6 V)

AC OK and DC OK – Signal status shall be HIGH (> 3.0 V)

AC not OK and DC OK – Signal status shall be Middle Level (Between 2 V and 2.5 V)

DC OK threshold is deﬁned as when the 12 V output is greater than 11.5 V.

DC not OK threshold is deﬁned as when the 12 V output is less than 11.4 V & greater than 11.3 V.

I-Mon (S7): Provides both the load sharing function (as a feedback for output regulation droop function) and 12 V output

current information.

PS INTERRUPT (S4): The signal behavior in response to certain operating condition changes in the power supply as deﬁned in the

Firmware Speciﬁcation section. This signal shall be pulled up to maximum 5 V logic level external to the PS.

PS ON (S8):

Required to remotely turn on/off the power supply. PSON# is an active low signal that turns on the main 12 V DC

output. When this signal is not pulled low by the system, or left open, the 12 V output is turned off. This signal is

pulled to a standby voltage by a pull-up resistor internal to the power supply. Refer to On/Off Timing for timing dia-

gram in TRN. When in off or standby condition, the main 12 V DC output will be less than 50 mV with respect to

output return.

Environmental Specications

Operating temperature: -10 °C to 50 °C

Storage temperature: -40 °C to +85 °C

Altitude, operating: 10,000 ft.

Electromagnetic susceptibility/Input transients: -EN61000-3-2

-EN61000-4-2, 4.3, 4-4, -4-5, 4-6, 4-11

RoHS & lead-free compliant

No tantalum caps.

Humidity:

5 to 90% RH, non-condensing

Shock and vibration speciﬁcatons: Complies with Astec Std. Speciﬁcations

MTBF (Demonstrated):

500K Hrs at full load, 50 °C

Ordering Information

Model Number Nominal Output

Voltage Set Point

Set Point

Tolerance

Total

Regulation

Minimum

Current

Maximum

Current

Output Ripple

P/P Over Current Stand-by Air Flow

DS460S-3-002 12.3 Vdc ± 0.2% +5% 1 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V @ 2.3 A STD

DS460S-3-003 12.3 Vdc ± 0.2% +5% 1 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V @ 2.3 A REV

DS460S-3-004

(5,000 m) 12.3 Vdc ± 0.2% ± 5.0% 1.0 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V @ 2.3 A STD

DS460S-3-005

(5,000 m) 12.3 Vdc ± 0.2% ± 5.0% 1.0 A 36.0 A 120 mV 45.9 A - 57.5 A* 12.0 V @ 2.3 A REV

*Overcurrent latches off if overcurrent lasts over 1 second, otherwise it is auto recovery.

DS460S Data Sheet

Mechanical Drawings

LED GREEN

EMI GASKET (8X)

3.5

7.6

0.8 (2X)

4.2

198.1 ± 0.6

187.8

70.86

43.2

SanAce (40 x 40 x 28 mm FAN)

Model No. 9GA0412P3J01

196.9 ± 0.65

39.9± 0.5

11.12

9.5 ± 0.6

PROGRAMMING WINDOWS

(COVERLABEL REMOVED)

136.9 (2X)

0.8 HEMMING

40.5 REF

0.7

RAMP TO FAN

TOP OF FAN TO

CHASSIS BOTTOM

9.9 8

25 (2X)

136.9 (6X)

86.4 ± 0.55

7.75 ± 0.65

LATCH(BLACK)

3.2

HANDLE

MODEL

(TEXT AS ORIENTED)

LABEL LOCATION

243.2

43.2

Weight: 1.88 lbs

DS460S Data Sheet

Connector Denitions

AC Input Connector

Pin 1 Line

Pin 2 Neutral

Pin 3 Eath Ground

Output Connector - Power Blades

PB1 Vo

PB2 Vo

PB3 Vo

PB4 RTN

PB5 RTN

PB6 RTN

PB7 RTN

PB8 RTN

PB9 Vo

PB10 Vo

Earth Ground

Power Supply Output Card Edge (Top Side)

PB5

S1S8

PB4 PB3 PB2 PB1

Power Supply Output Card Edge (Bottom Side)

PB6 PB7 PB8 PB9 PB10

S9 S16

Output Connector - Signal Blades

S1 VSB

S2 VSB

S3 Reserved

S4 PS INTERRUPT

S5 PS PRESENT

S6 PSOK

S7 I-MON

S8 PSON#

S9 SCL*

S10 SDA

S11 GND

S12 ADD0

S13 ADD1

S14 ADD2

S15 RTN

S16 RTN

*Supports I2C standard mode (100 kHz) only

DS460S Data Sheet

WORLDWIDE OFFICES

Americas

2900 S.Diablo Way

Tempe, AZ 85282

USA

+1 888 412 7832

Europe (UK)

Waterfront Business Park

Merry Hill, Dudley

West Midlands, DY5 1LX

United Kingdom

+44 (0) 1384 842 211

Asia (HK)

14/F, Lu Plaza

2 Wing Yip Street

Kwun Tong, Kowloon

Hong Kong

+852 2176 3333

For more information: www.artesyn.com/power

For support: productsupport.ep@artesyn.com

While every precaution has been taken to ensure accuracy and completeness in this literature, Artesyn

Embedded Technologies assumes no responsibility, and disclaims all liability for damages resulting from use of

this information or for any errors or omissions. Artesyn Embedded Technologies, Artesyn and the Artesyn

Embedded Technologies logo are trademarks and service marks of Artesyn Embedded Technologies, Inc. All other

names and logos referred to are trade names, trademarks, or registered trademarks of their respective owners.

www.artesyn.com

DS460S-DS Rev. 08.13.14

Power/Signal Mating Connectors and Pin Types

Reference On Power Supply Mating Connector or Equivalent

AC Input Connector IEC320-C13 IEC320-C14

Output Connector PCB card edge (0.062”) Molex 459840007 (top mount)

Molex 459841122 (bottom mount)

Mouser Electronics

Authorized Distributor

Click to View Pricing, Inventory, Delivery & Lifecycle Information:

Artesyn Embedded Technologies:

DS460S-3-005 DS460S-3-004 DS460S-3-003 DS460S-3-002