True Accuracy, 16-Bit 12 V/15 V, Serial Input Voltage Output DAC AD5570 FEATURES FUNCTIONAL BLOCK DIAGRAM VSS VDD DGND AD5570 POWER-ON RESET REFGND 2R 16-BIT DAC VOUT AGND R AGNDS R DAC REGISTER REFIN POWER-DOWN CONTROL LOGIC PD SHIFT REGISTER LDAC SDIN SCLK SYNC SDO CLR 03760-001 Full 16-bit performance 1 LSB maximum INL and DNL Output voltage range up to 14 V On-board reference buffers, eliminating the need for a negative reference Controlled output during power-on Temperature ranges of -40C to +85C for A/B version/-40C to +125C for W/Y version Settling time of 10 s to 0.003% Clear function to 0 V Asynchronous update of outputs (LDAC pin) Power-on reset Serial data output for daisy chaining Data readback facility Figure 1. APPLICATIONS Industrial automation Automatic test equipment Process control Data acquisition systems General-purpose instrumentation GENERAL DESCRIPTION The AD5570 is a single 16-bit serial input, voltage output DAC that operates from supply voltages of 11.4 V up to 16.5 V. Integral linearity (INL) and differential nonlinearity (DNL) are accurate to 1 LSB. During power-up, when the supply voltages are changing, VOUT is clamped to 0 V via a low impedance path. The AD5570 DAC comes complete with a set of reference buffers. The reference buffers allow a single, positive reference to be used. The voltage on REFIN is gained up and inverted internally to give the positive and negative reference for the DAC core. Having the reference buffers on-chip eliminates the need for external components such as inverters, precision amplifiers, and resistors, thereby reducing the overall solution size and cost. The AD5570 uses a versatile 3-wire interface that is compatible with SPI(R), QSPITM, MICROWIRETM, and DSP(R) interface standards. Data is presented to the part as a 16-bit serial word. Serial data is available on the SDO pin for daisy-chaining purposes. Data readback allows the user to read the contents of the DAC register via the SDO pin. Features on the AD5570 include LDAC which is used to update the output of the DAC. The device also has a power-down pin (PD), allowing the DAC to be put into a low power state, and a CLR pin that allows the output to be cleared to 0 V. The AD5570 is available in a 16-lead SSOP. PRODUCT HIGHLIGHTS 1. 1 LSB maximum INL and DNL. 2. Buffered voltage output up to 14 V. 3. Output controlled during power-up. 4. On-board reference buffers. 5. Wide temperature range of -40C to +125C. Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 (c)2006 Analog Devices, Inc. All rights reserved. AD5570 TABLE OF CONTENTS Features .............................................................................................. 1 DAC Architecture....................................................................... 16 Applications....................................................................................... 1 Reference Buffers........................................................................ 16 Functional Block Diagram .............................................................. 1 Serial Interface ............................................................................ 16 General Description ......................................................................... 1 Transfer Function....................................................................... 17 Product Highlights ........................................................................... 1 Clear (CLR) ................................................................................. 17 Revision History ............................................................................... 2 Power-Down (PD) ..................................................................... 17 Specifications..................................................................................... 3 Power-On Reset.......................................................................... 17 Timing Characteristics..................................................................... 5 Serial Data Output (SDO)......................................................... 17 Standalone ..................................................................................... 5 Applications Information .............................................................. 19 Timing Characteristics..................................................................... 6 Typical Operating Circuit ......................................................... 19 Daisy-Chaining and Readback ................................................... 6 Layout Guidelines....................................................................... 20 Absolute Maximum Ratings............................................................ 8 Opto-Isolators............................................................................. 20 ESD Caution.................................................................................. 8 Microprocessor Interfacing....................................................... 21 Pin Configuration and Function Descriptions............................. 9 Evaluation Board ........................................................................ 22 Terminology .................................................................................... 10 Outline Dimensions ....................................................................... 24 Typical Performance Characteristics ........................................... 11 Ordering Guide .......................................................................... 24 General Description ....................................................................... 16 REVISION HISTORY 9/06--Rev. A to Rev. B Updated Format..................................................................Universal Changes to Table 3............................................................................ 6 Changes to Figure 43...................................................................... 21 Changes to AD5570 to 8xC51 Interface Section ........................ 21 Changes to Ordering Guide .......................................................... 24 4/05--Rev. 0 to Rev. A Changes to Table 1............................................................................ 3 Changes to Table 4............................................................................ 8 Added Figure 16.............................................................................. 12 Revision 0: Initial Version Rev. B | Page 2 of 24 AD5570 SPECIFICATIONS VDD = +11.4 V to +16.5 V, VSS = -11.4 V to -16.5 V, VREF = 5 V, REFGND = AGND = DGND = 0 V, RL = 5 k, CL = 200 pF to AGND; all specifications TMIN to TMAX, unless otherwise noted. Table 1. Parameter 1 ACCURACY Resolution Monotonicity Differential Nonlinearity (DNL) Relative Accuracy (INL) B/Y Grade A/W Grade Positive INL Drift Over Time 3 A/B Grades W/Y Grades Negative Full-Scale Error Full-Scale Error Bipolar Zero Error Gain Error Gain Temperature Coefficient 4 REFERENCE INPUT Reference Input Range4 Input Current OUTPUT CHARACTERISTICS4 Output Voltage Range Min Max Unit Test Conditions/Comments 16 16 -1 0.3 +1 Bits Bits LSB -1 -2 0.4 0.6 +1 +2 LSB LSB 7.5 6 7.5 7.5 1.5 ppm ppm mV mV mV mV ppm FSR/C 5 7 0.1 V V A With 11.4 V supplies With 16.5 V supplies VDD - 1.4 VDD - 2.5 16 13 7 V V s s s V/s nV-s With 11.4 V supplies With 16.5 V supplies At 16 bits to 0.5 LSB To 0.0003% 512 LSB code change Measured from 10% to 90% 12 V supplies; 1 LSB change around the major carry See Figure 16 2.5 6.5 0.9 1.8 0.9 1.8 +0.25 4 4 5 5 VSS + 1.4 VSS + 2.5 Output Voltage Settling Time 12 10 6 6.5 15 Slew Rate Digital-to-Analog Glitch Impulse Bandwidth Short Circuit Current Output Noise Voltage Density DAC Output Impedance Digital Feedthrough WARMUP TIME 5 LOGIC INPUTS Input Currents VINH, Input High Voltage VINL, Input Low Voltage CIN, Input Capacitance LOGIC OUTPUTS VOL, Output Low Voltage Floating-State Output Typ 2 20 25 85 0.35 0.5 12 0.5 0.1 2 0.8 3 0.4 8 Rev. B | Page 3 of 24 kHz mA nV/Hz nV-s sec f = 1 kHz; midscale loaded A V V pF V pF ISINK = 1 mA AD5570 Parameter 1 POWER REQUIREMENTS VDD/VSS IDD ISS Power-Down Current Power-Supply Sensitivity 6 Power Dissipation Min Typ 2 11.4 4 3.5 16 0.1 100 Max Unit Test Conditions/Comments 16.5 5 5 V mA mA A LSB/V mW VOUT unloaded VOUT unloaded VOUT unloaded 15 supplies 10%; full-scale loaded VOUT unloaded 1 Temperature ranges: A and B versions = - 40C to +85C; W and Y versions = -40C to +125C. Typical specifications at 12 V/15 V, +25C. 3 These numbers are generated from the life test of the part. 4 Guaranteed by design. 5 Warmup time is required for the device to reach thermal equilibrium, thus achieving rated performance. 6 Sensitivity of negative full-scale error and positive full-scale error to VDD, VSS variations. 2 Rev. B | Page 4 of 24 AD5570 TIMING CHARACTERISTICS STANDALONE VDD = +12 V 5%, VSS = -12 V 5% or VDD = +15 V 10%, VSS = -15 V 10%, VREF = 5 V, REFGND = AGND = DGND = 0 V, RL = 5 k, CL = 200 pF to AGND; all specifications TMIN to TMAX, unless otherwise noted. Table 2. Parameter 1, 2 fMAX t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t11 t12 t13 2 Unit MHz max ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min Description SCLK frequency SCLK cycle time SCLK high time SCLK low time SYNC to SCLK falling edge setup time Data setup time Data hold time SCLK falling edge to SYNC rising edge Minimum SYNC high time SYNC rising edge to LDAC falling edge LDAC pulse width LDAC falling edge to SYNC falling edge (no update) LDAC rising edge to SYNC rising edge (no update) CLR pulse width All parameters guaranteed by design and characterization. Not production tested. All input signals are measured with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of (VIL +VIH)/2. t1 SCLK t2 t8 t3 t4 t7 SYNC t6 t5 SDIN DB15 DB0 t9 t10 LDAC1 t11 t12 LDAC2 t13 CLR NOTES 1ASYNCHRONOUS LDAC UPDATE MODE. UPDATE ON FALLING EDGE OF LDAC. 2SYNCHRONOUS LDAC UPDATE MODE. UPDATE ON RISING EDGE OF SYNC. Figure 2. Serial Interface Timing Diagram Rev. B | Page 5 of 24 03760-002 1 Limit at TMIN, TMAX 10 100 35 35 10 35 0 45 45 0 50 0 0 20 AD5570 TIMING CHARACTERISTICS DAISY-CHAINING AND READBACK VDD = +12 V 5%, VSS = -12 V 5% or VDD = +15 V 10%, VSS = -15 V 10%, VREF = 5 V, REFGND = AGND = DGND = 0 V, RL = 5 k, CL = 200 pF to AGND; all specifications TMIN to TMAX, unless otherwise noted. Table 3. Parameter 1, 2 fMAX t1 t2 t3 t4 t5 t6 t7 t8 t9 t10 t14 3 Limit at TMIN, TMAX 2 500 200 200 10 35 0 45 45 0 50 200 Unit MHz max ns min ns min ns min ns min ns min ns min ns min ns min ns min ns min ns max Description SCLK frequency SCLK cycle time SCLK high time SCLK low time SYNC to SCLK falling edge setup time Data setup time Data hold time SCLK falling edge to SYNC rising edge Minimum SYNC high time SYNC rising edge to LDAC falling edge LDAC pulse width Data delay on SDO 1 All parameters guaranteed by design and characterization. Not production tested. All input signals are measured with tr = tf = 5 ns (10% to 90% of VDD) and timed from a voltage level of (VIL +VIH)/2. SDO; RPULLUP = 5 k, CL = 15 pF. 3 With CL = 0 pF, t14 = 100 ns. 2 t1 SCLK t8 t3 t4 t2 t7 SYNC t10 LDAC1 t9 LDAC2 t5 SDIN t6 DB15 (N) DB0 (N) DB15 (N + 1) DB0 (N + 1) t14 SDO DB15 (N) 03760-003 NOTES 1ASYNCHRONOUS LDAC UPDATE MODE. 2SYNCHRONOUS LDAC UPDATE MODE. DB0 (N) DB15 (N + 1) Figure 3. Daisy-Chaining Timing Diagram Rev. B | Page 6 of 24 AD5570 t1 SCLK t2 t8 t4 t3 t7 SYNC t6 t5 SDIN DB15 (N) DB0 (N) DB15 (N + 1) DB0 (N + 1) t10 LDAC t9 DB15 (N) SDO Figure 4. Readback Timing Diagram Rev. B | Page 7 of 24 DB14 (N) DB0 (N) 03760-004 t14 AD5570 ABSOLUTE MAXIMUM RATINGS TA = 25C, unless otherwise noted. Table 4. Parameter VDD to AGND, AGNDS, DGND VSS to AGND, AGNDS, DGND AGND, AGNDS to DGND REFGND to AGND, ADNDS REFIN to AGND, AGNDS REFIN to REFGND Digital Inputs to DGND VOUT to AGND, AGNDS SDO to DGND Operating Temperature Range W/Y Grades A/B Grades Storage Temperature Range Maximum Junction Temperature (TJ max) 16-Lead SSOP Package Power Dissipation JA Thermal Impedance Lead Temperature (Soldering, 10 sec) IR Reflow, Peak Temperature Rating -0.3 V to +17 V +0.3 V to -17 V -0.3 V to +0.3 V -0.3 V to +0.3 V -0.3 V to +17 V -0.3 V to +17 V -0.3 V to VDD + 0.3 V VSS - 0.3 V to VDD + 0.3 V -0.3 V to +6.5 V Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ESD CAUTION -40C to +125C -40C to +85C -65C to +150C 150C (TJ max - TA)/JA 139C/W 300C 230C Rev. B | Page 8 of 24 AD5570 PIN CONFIGURATION AND FUNCTION DESCRIPTIONS VSS 1 16 REFGND VDD 2 15 REFIN CLR 3 AD5570 14 REFGND SDIN 7 10 PD SDO 8 9 DGND 03760-005 13 VOUT TOP VIEW SYNC 5 (Not to Scale) 12 AGNDS SCLK 6 11 AGND LDAC 4 Figure 5. Pin Configuration Table 5. Pin Function Descriptions Pin No. 1 2 3 Mnemonic VSS VDD CLR 4 LDAC 5 SYNC 6 SCLK 7 8 SDIN SDO 9 10 11 12 13 14, 16 15 DGND PD AGND AGNDS VOUT REFGND REFIN Description Negative Analog Supply Voltage. -12 V 5% to -15 V 10% for specified performance. Positive Analog Supply Voltage. 12 V 5% to 15 V 10% for specified performance. Level Sensitive, Active Low Input. A falling edge of CLR resets VOUT to AGND. The contents of the registers are untouched. Active Low Control Input. Transfers the contents of the input register to the DAC register. LDAC can be tied permanently low, enabling the outputs to be updated on the rising edge of SYNC. Active Low Control Input. This is the frame synchronization signal for the data. When SYNC goes low, it powers on the SCLK and SDIN buffers and enables the input shift register. Data is transferred in on the falling edges of the following 16 clocks. Serial Clock Input. Data is clocked into the input register on the falling edge of the serial clock input. Data can be transferred at rates of up to 8 MHz. Serial Data Input. Data is clocked into the 16-bit register on the falling edge of the serial clock input. Serial Data Output. Can be used for daisy-chaining a number of devices together or for reading back the data in the shift register for diagnostic purposes. This is an open-drain output; it must be pulled to logic high with an external pull-up resistor of ~5 k. Digital Ground. Ground reference for all digital circuitry. Active Low Control Input. Allows the DAC to be put into a power-down state. Analog Ground. Ground reference for all analog circuitry. Analog Ground Sense. This is normally tied to AGND. Analog Output Voltage. Reference Ground. Tie this pin to 0 V. Voltage Reference Input. This is internally buffered before being applied to the DAC. For bipolar 10 V output range, REFIN is 5 V. Rev. B | Page 9 of 24 AD5570 TERMINOLOGY Relative Accuracy or Integral Nonlinearity (INL) Relative accuracy or integral nonlinearity is a measure of the maximum deviation, in LSBs, from a straight line passing through the endpoints of the DAC transfer function. Output Voltage Settling Time Output voltage settling time is the amount of time it takes for the output to settle to a specified level for a full-scale input change. Monotonicity A DAC is monotonic if the output either increases or remains constant for increasing digital inputs. The AD5570 is monotonic over its full operating temperature range. Differential Nonlinearity (DNL) Differential nonlinearity is the difference between the measured change and the ideal 1 LSB change between any two adjacent codes. A specified differential nonlinearity of 1 LSB maximum ensures monotonicity. Gain Error Gain error is the difference between the actual and ideal analog output range, expressed as a percent of the full-scale range. It is the deviation in slope of the DAC transfer characteristic from the ideal. Gain Error Temperature Coefficient Gain error temperature coefficient is a measure of the change in gain error with changes in temperature. It is expressed in ppm/C. Negative Full-Scale Error/Zero Scale Error Negative full-scale error is the error in the DAC output voltage when all 0s are loaded into the DAC latch. Ideally, the output voltage, with all 0s in the DAC latch, is -2 VREF. Full-Scale Error Full-scale error is the error in the DAC output voltage when all 1s are loaded to the DAC latch. Ideally, the output voltage with all 1s loaded into the DAC latch is 2 VREF - 1 LSB. Bipolar Zero Error Bipolar zero error is the deviation of the analog input from the ideal half-scale output of 0.0000 V when the inputs are loaded with 0x8000. Slew Rate The slew rate of a device is a limitation in the rate of change of output voltage. The output slewing speed of a voltage-output DAC converter is usually limited by the slew rate of the amplifier used at its output. Slew rate is measured from 10% to 90% of the output signal and is given in V/s. Digital-to-Analog Glitch Impulse Digital-to-analog glitch impulse is the amount of charge injected into the analog output when the input codes in the DAC register change state. It is specified as the area of the glitch in nV-s and is measured when the digital input code changes by 1 LSB at the major carry transition, that is, from code 0x7FFF to 0x8000. Bandwidth The reference amplifiers within the DAC have a finite bandwidth to optimize noise performance. To measure it, a sine wave is applied to the reference input (REFIN), with full-scale code loaded to the DAC. The bandwidth is the frequency at which the output amplitude falls to 3 dB below the input. Digital Feedthrough Digital feedthrough is a measure of the impulse injected into the analog output of the DAC from the digital inputs of the DAC, but is measured when the DAC output is not updated. SYNC is held high, while the SCLK and SDIN signals are toggled. Digital feedthrough is specified in nV-s and is measured with a full-scale code change on the data bus, that is, from all 0s to all 1s, and vice versa. Power Supply Sensitivity Power supply sensitivity indicates how the output of the DAC is affected by changes in the power supply voltage. Rev. B | Page 10 of 24 AD5570 TYPICAL PERFORMANCE CHARACTERISTICS 1.0 TA = 25C VDD/VSS = 15V REFIN = +5V 0.8 0.6 0.4 0.2 0.2 DNL (LSB) 0.4 0 -0.2 -0.4 -0.6 -0.6 -0.8 -0.8 0 10k 20k 30k CODE 40k 50k 60k -1.0 Figure 6. Integral Nonlinearity vs. Code, VDD/VSS = 15 V 30k CODE 40k 50k 60k 0.8 0.6 0.4 0.2 0.2 INL (LSB) 0.4 0 -0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 10k 20k 30k CODE 40k 50k 60k -1.0 -40 03760-007 0 VDD/VSS = 15V REFIN = +5V Figure 7. Differential Nonlinearity vs. Code, VDD/VSS = 15 V -20 0 20 40 60 TEMPERATURE (C) 80 100 120 03760-018 0.6 DNL (LSB) 20k 1.0 TA = 25C VDD/VSS = 15V REFIN = +5V 0.8 Figure 10. Integral Nonlinearity vs. Temperature, VDD/VSS = 15 V 1.0 1.0 TA = 25C VDD/VSS = 12V REFIN = +5V 0.8 0.6 0.8 0.2 DNL (LSB) 0.4 0.2 0 -0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 10k 20k 30k CODE 40k 50k 60k Figure 8. Integral Nonlinearity vs. Code, VDD/VSS = 12 V -1.0 -40 03760-008 0 VDD/VSS = 15V REFIN = +5V 0.6 0.4 -1.0 10k Figure 9. Differential Nonlinearity vs. Code, VDD/VSS = 12 V 1.0 -1.0 0 -20 0 20 40 60 TEMPERATURE (C) 80 100 120 03760-019 -1.0 INL (LSB) 0 -0.2 -0.4 03760-006 INL (LSB) 0.6 TA = 25C VDD/VSS = 12V REFIN = +5V 0.8 03760-009 1.0 Figure 11. Differential Nonlinearity vs. Temperature, VDD/VSS = 15 V Rev. B | Page 11 of 24 AD5570 1.0 1.0 0.4 0.2 0.2 DNL (LSB) 0.6 0.4 0 -0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -20 0 20 40 60 TEMPERATURE (C) 80 100 120 -1.0 11.4 03760-020 Figure 12. Integral Nonlinearity vs. Temperature, VDD/VSS = 12 V VDD/VSS = 16.5V TA = 125C 0.8 0.6 0.4 0.2 0.2 INL (LSB) 0.4 0 -0.2 0 -0.2 -0.4 -0.4 -0.6 -0.6 -0.8 -0.8 -1.0 -40 -20 0 20 40 60 TEMPERATURE (C) 80 100 120 -1.0 03760-021 DNL (LSB) 16.0 16.5 1.0 VDD/VSS = 12V REFIN = +5V 0.6 0 100 Figure 13. Differential Nonlinearity vs. Temperature, VDD/VSS = 12 V 200 300 400 500 600 TIME (Hours) 700 800 900 1000 Figure 16. INL Drift over Time 1.0 2.0 TA = 25C REFIN = 5V 0.8 VDD/VSS = 12V TA = 25C 1.5 0.6 INL ERROR (LSB) 0.4 0.2 0 -0.2 -0.4 -0.6 1.0 0.5 0 -0.8 -1.0 11.4 12.0 13.0 14.0 15.0 SUPPLY VOLTAGE (V) -1.0 2.0 16.0 16.5 Figure 14. Integral Nonlinearity vs. Supply Voltage 03760-026 -0.5 03760-023 INL (LSB) 13.0 14.0 15.0 SUPPLY VOLTAGE (V) Figure 15. Differential Nonlinearity vs. Supply Voltage 1.0 0.8 12.0 03760-052 INL (LSB) 0.6 -1.0 -40 TA = 25C REFIN = 5V 0.8 03760-024 VDD/VSS = 12V REFIN = +5V 0.8 2.5 3.0 3.5 4.0 4.5 REFERENCE VOLTAGE (V) 5.0 5.5 Figure 17. Integral Nonlinearity Error vs. Reference Voltage, VDD/VSS = 12 V Rev. B | Page 12 of 24 AD5570 0.5 1.0 VDD/VSS = 12V TA = 25C 0.3 0.6 0.2 0.4 0.1 0 -0.1 -0.2 -0.3 0.2 0 -0.2 -0.4 2.5 3.0 3.5 4.0 4.5 REFERENCE VOLTAGE (V) 5.0 -0.8 -1.0 2.0 5.5 Figure 18. Differential Nonlinearity Error vs. Reference Voltage, VDD/VSS = 12 V 4.0 5.5 6.0 6.5 3.5 |ISS| 0 3.0 -2.5 2.5 2.5 3.0 3.5 4.0 4.5 REFERENCE VOLTAGE (V) 5.0 2.0 11.4 5.5 12.4 13.4 14.4 VDD/VSS (V) 15.4 16.4 03760-029 2.5 |IDD| 15.4 16.4 03760-030 IDD/ISS (mA) 5.0 03760-028 TUE ERROR (LSB) 4.5 Figure 19. TUE Error vs. Reference Voltage, VDD/VSS = 15 V or 12 V Figure 22. IDD/ISS vs. VDD/VSS 25 2.0 0.5 0 -0.5 -1.0 03760-048 -1.5 2.5 3.0 3.5 4.0 4.5 5.0 REFERENCE VOLTAGE (V) 5.5 6.0 IDD/ISS POWER-DOWN CURRENT (A) TA = 25C REFIN = +5V VDD/VSS = 15V TA = 25C 1.0 INL ERROR (LSB) 3.5 4.0 4.5 5.0 REFERENCE VOLTAGE (V) TA = 25C REFIN = 5V 7.5 -2.0 2.0 3.0 5.0 VDD/VSS = 15V OR 12V TA = 25C 1.5 2.5 Figure 21. Integral Nonlinearity Error vs. Reference Voltage, VDD/VSS = 15 V 10.0 -5.0 2.0 03760-049 03760-027 -0.6 -0.4 -0.5 2.0 VDD/VSS = 15V TA = 25C 0.8 INL ERROR (LSB) DNL ERROR (LSB) 0.4 6.5 Figure 20. Integral Nonlinearity Error vs. Reference Voltage, VDD/VSS = 15 V Rev. B | Page 13 of 24 20 |IDD IN POWER-DOWN| 15 10 5 |ISS IN POWER-DOWN| 0 11.4 12.4 13.4 14.4 SUPPLY VOLTAGE (V) Figure 23. IDD/ISS in Power-Down vs. Supply Voltage AD5570 4.15 0 VDD/VSS = 12V OR 15V REFIN = 5V -1 -3 4.00 -4 -5 INCREASING 3.95 DECREASING -6 3.90 -7 3.85 INCREASING 12V SUPPLIES -8 -20 0 20 40 60 TEMPERATURE (C) 80 100 3.75 120 Figure 24. Offset Error vs. Temperature 03760-035 3.80 03760-031 -9 -10 -40 0 0.5 1.0 1.5 3.5 4.0 4.5 5.0 11 10 REFIN = +5V 8 VDD/VSS = 15V -2 6 -3 4 VDD/VSS = 12V -5 -6 2 0 -2 -7 -4 -8 -6 -9 -8 0 20 40 60 TEMPERATURE (C) 80 100 120 03760-032 -20 -10 1s/DIV VDD = +15V VSS = -15V REFIN = +5V TA = 25C TIME (s) Figure 25. Bipolar Zero Error vs. Temperature Figure 28. Settling Time 40 10 TA = 25C REFIN = +5V REFIN = +5V 35 6 30 VDD/VSS = 12V 4 25 TIME (s) 2 VDD/VSS = 15V 0 -2 -4 5 -20 0 20 40 60 TEMPERATURE (C) 80 100 120 03760-034 -8 -10 -40 VDD/VSS = 15V 15 10 VDD/VSS = 12V -6 20 0 0 1 2 3 4 5 6 CAPACITANCE (nF) 7 8 Figure 29.14-Bit Settling Time vs. Load Capacitance Figure 26. Gain Error vs. Temperature Rev. B | Page 14 of 24 9 9.4 03760-037 8 03760-046 VOUT (V) -4 -10 -40 GAIN ERROR (LSB) 2.0 2.5 3.0 VLOGIC (V) Figure 27. Supply Current vs. Logic Input Current for SCLK, SYNC, SDIN, and LDAC Increasing and Decreasing 0 BIPOLAR ZERO ERROR (LSB) 15V SUPPLIES DECREASING 4.05 IDD (mA) OFFSET ERROR (LSB) -2 -1 TA = 25C REFIN = 5V 4.10 AD5570 10.0000 -0.022 TA = 25C REFIN = 5V -0.027 -0.032 -0.037 9.9982 9.9979 15V SUPPLIES 9.9976 9.9973 9.9970 9.9967 9.9964 12V SUPPLIES -0.047 -0.052 -0.057 03760-038 9.9961 9.9958 9.9955 9.9952 -10 -0.042 -8 -6 -4 -2 SOURCE CURRENT (mA) 0 2 4 6 8 SINK CURRENT (mA) 10 -0.062 -0.067 VDD = +12V VSS = -12V REFIN = +5V TA = 25C 8000 7FFFH 03760-051 9.9994 9.9991 9.9988 9.9985 VOLTAGE (V) OUTPUT VOLTAGE (V) 9.9997 -0.072 1s/DIV Figure 30. Source and Sink Capability of Output Amplifier with Full-Scale Loaded Figure 33. Major Code Transition Glitch Energy, VDD/VSS = 12 V -9.9973 -9.9976 TA = 25C REFIN = 5V VDD = +15V VSS = -15V MIDSCALE LOADED 20V/DIV VREFIN = 0V OUTPUT VOLTAGE (V) -9.9979 12V SUPPLIES -9.9982 -9.9985 -9.9988 15V SUPPLIES -9.9991 -9.9994 -8 -6 -4 -2 SOURCE CURRENT (mA) 0 2 4 6 8 SINK CURRENT (mA) 10 CH1 20V/DIV Figure 31. Source and Sink Capability of Output Amplifier with Zero-Scale Loaded M 1.0ms 500kS/s A CH1 0.0V 20s/PT 03760-047 -10.0000 -10 03760-039 -9.9997 Figure 34. Peak-to-Peak Noise (100 kHz Bandwidth) -0.05 -0.06 VDD VDD = +15V VSS = -15V REFIN = +5V TA = 25C RAMP TIME = 100s VSS -0.08 -0.10 VOUT VDD = +15V VSS = -15V REFIN = +5V TA = 25C 7 FFF 8000H 1s/DIV Figure 32. Major Code Transition Glitch Energy, VDD/VSS = 15 V VDD/VSS = 10V/DIV VOUT = 10mV/DIV 100s/DIV Figure 35. VOUT vs. VDD/VSS on Power-Up Rev. B | Page 15 of 24 03760-042 -0.09 03760-040 VOUT (V) -0.07 AD5570 GENERAL DESCRIPTION On power-up, the input shift register and DAC register are loaded with midscale (0x8000). The DAC coding is straight binary; all 0s produce an output of -2 VREF; all 1s produce an output of +2 VREF - 1 LSB. The AD5570 is a single 16-bit serial input, voltage output DAC. It operates from supply voltages of 11.4 V to 16.5 V, and has a buffered voltage output of up to 13.6 V. Data is written to the AD5570 in a 16-bit word format, via a 3-wire serial interface. The device also offers an SDO pin, available for daisy-chaining or readback. The AD5570 incorporates a power-on reset circuit to ensure the DAC output powers up to 0 V. The device also has a power-down pin to reduce the typical current consumption to 16 A. DAC ARCHITECTURE The DAC architecture of the AD5570 consists of a 16-bit, currentmode, segmented R-2R DAC. The simplified circuit diagram for the DAC section is shown in Figure 36. The four MSBs of the 16-bit data word are decoded to drive 15 switches, E1 to E15. Each of these switches connects one of the 15 matched resistors to either AGND or IOUT. The remaining 12 bits of the data word drive switches S0 to S11 of the 12-bit R-2R ladder network. R VREF 2R 2R 2R R 2R After the end of the serial data transfer, data is automatically transferred from the input shift register to the input register of the DAC. When data has been transferred into the input register of the DAC, the DAC register and DAC output can be updated by taking LDAC low while SYNC is high. R 2R 2R The SYNC input is a level-triggered input that acts as a frame synchronization signal and chip enable. SYNC must frame the serial word being loaded into the device. Data can be transferred into the device only while SYNCis low. To start the serial data transfer, SYNC is taken low, observing the minimum SYNC to SCLK falling edge setup time, t4. After SYNC goes low, serial data on SDIN is shifted into the device's input shift register on the falling edges of SCLK. SYNC can be taken high after the falling edge of the 16th SCLK pulse, observing the minimum SCLK falling edge to SYNC rising edge time, t7. 2R Load DAC Input (LDAC) E14 E1 S11 S10 S0 R/8 There are two ways that the DAC register and DAC output can be updated when data has been transferred into the input register of the DAC. Depending on the status of both SYNC and LDAC, one of two update modes is selected. IOUT 4 MSBs DECODED INTO 15 EQUAL SEGMENTS VOUT 03760-010 AGND 12-BIT R-2R LADDER Figure 36. DAC Ladder Structure REFERENCE BUFFERS The AD5570 operates with an external reference. The reference input (REFIN) has an input range of up to 7 V. This input voltage is then used to provide a buffered positive and negative reference for the DAC core. The positive reference is given by +VREF = 2 x V REFIN The first mode is synchronous LDAC. In this mode, LDAC is low while data is being clocked into the input shift register. The DAC output is updated when SYNC is taken high. The update here occurs on the rising edge of SYNC. The second mode is asynchronous LDAC. In this mode, LDAC is high while data is being clocked in. The DAC output is updated by taking LDAC low any time after SYNC has been taken high. The update now occurs on the falling edge of LDAC. Figure 37 shows a simplified block diagram of the input loading circuitry. and the negative reference to the DAC core is given by -VREF = 2 x VREFIN OUTPUT I/V AMPLIFIER These positive and negative reference voltages define the DAC output range. VREFIN SERIAL INTERFACE LDAC The AD5570 is controlled over a versatile 3-wire serial interface that operates at clock rates up to 10 MHz and is compatible with SPI, QSPI, MICROWIRE, and DSP interface standards. SYNC SDIN Input Shift Register The input shift register is 16 bits wide. Data is loaded into the device as a 16-bit word under the control of a serial clock input, SCLK. The timing diagram for this operation is shown in Figure 2. 16-BIT DAC VOUT DAC REGISTER INPUT SHIFT REGISTER SDO 03760-012 E15 Figure 37. Simplified Serial Interface Showing Input Loading Circuitry Rev. B | Page 16 of 24 AD5570 TRANSFER FUNCTION POWER-DOWN (PD) Table 6 shows the ideal input code to the output voltage relationship for the AD5570. The power-down pin allows the user to place the AD5570 into a power-down mode. In power-down mode, power consumption is at a minimum; the device typically consumes only 16 A. Table 6. Binary Code Table POWER-ON RESET Digital Input MSB 1111 1000 1000 0111 0000 1111 0000 0000 1111 0000 1111 0000 0000 1111 0000 LSB 1111 0001 0000 1111 0000 The AD5570 contains a power-on reset circuit that controls the output during power-up and power-down. This is useful in applications where the known state of the output of the DAC during power-up is important. On power-up and power-down, the output of the DAC and VOUT, is held at AGND. Analog Output (VOUT) +2 VREF x (32,767/32,768) +2 VREF x (1/32,768) 0V -2 VREF x (1/32,768) -2 VREF SERIAL DATA OUTPUT (SDO) The SDO is the internal shift registers output. For the AD5570, SDO is an internal pull-down only; an external pull-up resistor of ~5 k to external logic high is required. SDO pull-down is disabled when the device is in power-down, thus saving current. The output voltage expression is given by VOUT = -2 VREFIN + 4 x V REFIN [D / 65536] where: D is the decimal equivalent of the code loaded to the DAC. VREFIN is the reference voltage available at the REFIN pin. CLEAR (CLR) CLR is an active low digital input that allows the output to be cleared to 0 V. When the CLR signal is brought back high, the output stays at 0 V until LDAC is brought low. The relationship between LDAC and CLR is explained further in Table 7. Table 7. Relationships Among PD, CLR, and LDAC PD CLR LDAC Comments 0 x x PD has priority over LDAC and CLR. The output remains at 0 V through an internal 20 k resistor. It is still possible to address both the input register and DAC register when the AD5570 is in power-down. Data is written to the input register and DAC register. CLR has higher priority over LDAC; therefore, the output is at 0 V. Data is written to the input register only. The output is at 0 V and remains at 0 V when CLR is taken back high. Data is written to the input register and the DAC register. The output is driven to the DAC level. Data is written to the input register only. The output of the DAC register is unchanged. 1 0 0 1 0 1 1 1 0 1 1 1 The availability of SDO allows any number of AD5570s to be daisy-chained together. It also allows for the contents of the DAC register, or any number of DACs daisy-chained together, to be read back for diagnostic purposes. Daisy Chaining This mode of operation is designed for multi DAC systems, where several AD5570s can be connected in cascade as shown in Figure 38. This is done by connecting the control inputs in parallel and then daisy-chaining the SDIN and SDO I/Os of each device. An external pull-up resistor of ~5 k on SDO is required when using the part in daisy-chain mode. As described earlier, when SYNC goes low, serial data on SDIN is shifted into the input shift register on the falling edge of SCLK. If more than 16 clock pulses are applied, the data ripples out of the shift resister and appears on the SDO line. By connecting this line to the SDIN input on the next AD5570 in the chain, a multi DAC interface can be constructed. One data transfer cycle of 16 SCLK pulses is required for each DAC in the system. Therefore, the total number of clock cycles must equal 16 N, where N is the total number of devices in the chain. The first data transfer cycle written into the chain appears at the last DAC in the system on the final data transfer cycle. When the serial transfer to all devices is complete, take SYNC high. This prevents any further data from being clocked into the devices. A continuous SCLK source can be used if SYNC is held low for the correct number of clock cycles. Alternatively, a burst clock containing the exact number of clock cycles can be used and SYNC is taken high some time later. The outputs of all the DACs in the system can be updated simultaneously using the LDAC signal. Rev. B | Page 17 of 24 AD5570 Readback The AD5570 allows the data contained in the DAC register to be read back, if required. As with daisy chaining, an external pull-up resistor of ~5 k on SDO is required. The data in the DAC register is available on SDO on the falling edges of SCLK when SYNC is low. On the 16th SCLK edge, SDO is updated to repeat SDIN with a delay of 16 clock cycles. 68HC11* To read back the contents of the DAC register without writing to the part, take SYNC low while LDAC is held high. Daisy-chaining readback is also possible through the SDO pin of the last device in the DAC chain because the DAC data passes through the DAC chain with the appropriate latency. AD5570* MOSI SDIN SCK SCLK PC7 SYNC PC6 LDAC VLOGIC SDO MISO R SDIN AD5570* SCLK SYNC LDAC SDO R SDIN AD5570* SCLK SYNC SDO R *ADDITIONAL PINS OMITTED FOR CLARITY. Figure 38. Daisy-Chaining Using the AD5570 Rev. B | Page 18 of 24 03760-013 LDAC AD5570 APPLICATIONS INFORMATION TYPICAL OPERATING CIRCUIT 1 VSS Figure 39 shows the typical operating circuit for the AD5570. The only external component needed for this precision 16-bit DAC is a single external positive reference. Because the device incorporates reference buffers, it eliminates the need for a negative reference, external inverters, precision amplifiers, and resistors. This leads to an overall savings of both cost and board space. 2 VDD REFIN 15 3 CLR REFGND 14 4 LDAC 5 SYNC AGNDS 12 6 SCLK AGND 11 7 SDIN PD 10 8 SDO DGND 9 In the circuit shown in Figure 39, VDD and VSS are both connected to 15 V, but VDD and VSS can operate supplies from 11.4 V to 16.5 V. AGNDS is connected to AGND, but the option of force/ sense is included on this device if required by the user. +15V 0.1F 10F 1 VSS REFGND 16 2 VDD REFIN 15 REFGND 14 3 CLR LDAC 4 LDAC SYNC 5 SYNC AGNDS 12 SCLK 6 SCLK AGND 11 SDIN 7 SDIN PD 10 SDO 8 SDO DGND 9 AD5570 VOUT 13 AD5570 VOUT 13 6 2 3 OP177* *FOR OPTIMUM SETTLING TIME PERFORMANCE, THE AD845 IS RECOMMENDED. 03760-045 (OTHER CONNECTIONS OMITTED FOR CLARITY) 10F Figure 40. Driving AGND and AGNDS Using a Force/Sense Amplifier The four possible sources of error to consider when choosing a voltage reference for high accuracy applications are initial accuracy, long-term drift, temperature coefficient of the output voltage, and output voltage noise. ADR435 VOUT 03760-044 0.1F -15V REFGND 16 5k 5V Figure 39. Typical Operating Circuit Force/Sense of AGND Because of the extremely high accuracy of this device, system design issues (such as grounding and contact resistance) are very important. The AD5570, with 10 V output, has an LSB size of 305 V. Therefore, series wiring and connector resistances of very small values can cause voltage drops of an LSB. For this reason, the AD5570 offers a force/sense output configuration. Figure 40 shows how to connect the AD5570 to the force/sense amplifier. Where accuracy of the output is important, an amplifier such as the OP177 is ideal. The OP177 is ultraprecise with offset voltages of 10 V maximum at room temperature, and offset drift of 0.1 V/C maximum. Alternative recommended amplifiers are the OP1177 and the OP77. For applications where optimization of the circuit for settling time is needed, the AD845 is recommended. Precision Voltage Reference Selection To achieve the optimum performance from the AD5570, give special attention to the selection of a precision voltage reference. The AD5570 has just one reference input, REFIN. This voltage on REFIN is used to provide a buffered positive and negative reference for the DAC core. Therefore, any error in the voltage reference is reflected in the output of the device. Initial accuracy on the output voltage of an external reference can lead to a full-scale error in the DAC. Therefore, to minimize these errors, a reference with low initial accuracy specification is preferred. Also, choosing a reference with an output trim adjustment, such as the ADR425, allows a system designer to trim out system errors by setting the reference voltage to a voltage other than the nominal. The trim adjustment can also be used at temperature to trim out any error. Long-term drift (LTD) is a measure of how much the reference drifts over time. A reference with a tight long-term drift specification ensures that the overall solution remains relatively stable over its entire lifetime. The temperature coefficient of a references output voltage affects INL, DNL, and TUE. Choose a reference with a tight temperature coefficient specification to reduce the depend ence of the DAC output voltage on ambient conditions. In high accuracy applications that have a relatively low noise budget, reference output voltage noise needs to be considered. It is important to choose a reference with as low an output noise voltage as practical for the system resolution required. Precision voltage references, such as the ADR435 (XFET(R) design), produce low output noise in the 0.1 Hz to 10 Hz region. However, as the circuit bandwidth increases, filtering the output of the reference can be required to minimize the output noise. Rev. B | Page 19 of 24 AD5570 Table 8. Partial List of Precision References Recommended for Use with the AD5570 Part No. Initial Accuracy (mV max) Long-Term Drift (ppm typ) Temp Drift (ppm/ C max) 0.1 Hz to 10 Hz Noise (V p-p typ) ADR435 ADR425 ADR021 ADR395 AD586 6 6 5 6 2.5 30 50 50 50 15 3 3 3 25 10 3.4 3.4 15 5 4 OPTO-ISOLATORS Available in SC70 package. LAYOUT GUIDELINES In any circuit where accuracy is important, careful consideration of the power supply and ground return layout helps to ensure the rated performance. The printed circuit board that the AD5570 is mounted on is designed so the analog and digital sections are separated and confined to certain areas of the board. If the AD5570 is in a system where multiple devices require an AGND-to-DGND connection, the connection is made at one point only. The star ground point is established as close as possible to the device. In many process control applications, it is necessary to provide an isolation barrier between the controller and the unit being controlled. Opto-isolators provide voltage isolation in excess of 3 kV. The serial loading structure of the AD5570 makes it ideal for opto-isolated interfaces, because the number of interface lines is kept to a minimum. Figure 41 shows a 4-channel isolated interface to the AD5570. To reduce the number of opto-isolators, the LDAC pin can be tied permanently low if the simultaneous updating of the DAC is not required. The DAC can then be updated on the rising edge of SYNC. The AD5570 has ample supply bypassing of 10 F in parallel with 0.1 F on each supply located as close to the package as possible, ideally right up against the device. The 10 F capacitors are the tantalum bead type. The 0.1 F capacitor has low effective series resistance (ESR) and effective series inductance (ESI) such as the common ceramic types that provide a low impedance path to ground at high frequencies to handle transient currents due to internal logic switching. The power supply lines of the AD5570 use as large a trace as possible to provide low impedance paths and reduce the effects of glitches on the power supply line. Fast switching signals such as clocks are shielded with digital ground to avoid radiating noise to other parts of the board, and are never be run near the reference inputs. A ground line routed between the SDIN and SCLK lines reduces crosstalk between them; this is not required on a multilayer board that has a separate ground plane, but separating the lines helps. It is essential to minimize noise on the REFIN line because it couples through to the DAC output. Rev. B | Page 20 of 24 VCC CONTROLLER CONTROL OUT TO LDAC SYNC OUT TO SYNC SERIAL CLOCK OUT TO SCLK TO SDIN SERIAL DATA OUT OPTO-COUPLER Figure 41. Opto-Isolated Interface 03760-050 1 Avoid crossover of digital and analog signals. Traces on opposite sides of the board must run at right angles to each other. This reduces the effects of feed through the board. A microstrip technique is by far the best, but not always possible with a double-sided board. In this technique, the component side of the board is dedicated to ground plane, while signal traces are placed on the solder side. AD5570 Microprocessor interfacing to the AD5570 is via a serial bus that uses standard protocol compatible with microcontrollers and DSP processors. The communications channel is a 3-wire (minimum) interface consisting of a clock signal, a data signal, and a synchronization signal. The AD5570 requires a 16-bit data word with data valid on the falling edge of SCLK. For all the interfaces, the DAC output update can be done automatically when all the data is clocked in, or it can be done under the control of LDAC. The contents of the DAC register can be read using the readback function. AD5570 to MC68HC11 Interface Figure 42 shows an example of a serial interface between the AD5570 and the MC68HC11 microcontroller. The serial peripheral interface (SPI) on the MC68HC11 is configured for master mode (MSTR = 1), clock polarity bit (CPOL = 0), and the clock phase bit (CPHA = 1). The SPI is configured by writing to the SPI control register (SPCR); see documentation on the MC68HC11. SCK of the MC68HC11 drives the SCLK of the AD5570, the MOSI output drives the serial data line (SDIN) of the AD5570, and the MISO input is driven from SDO. The SYNC is driven from one of the port lines, in this case, PC7. When data is being transmitted to the AD5570, the SYNC line (PC7) is taken low and data is transmitted MSB first. Data appearing on the MOSI output is valid on the falling edge of SCK. Eight falling clock edges occur in the transmit cycle; therefore, in order to load the required 16-bit word, PC7 is not brought high until the second 8-bit word has been transferred to the DACs input shift register. SDO SDIN SCLK SCLK PC7 SYNC *ADDITIONAL PINS OMITTED FOR CLARITY. The AD5570 requires a clock synchronized to the serial data. For this reason, the 8xC51 must be operated in Mode 0. In this mode, serial data enters and exits through RxD, and a shift clock is output on TxD. P3.3 and P3.4 are bit-programmable pins on the serial port and are used to drive SYNC and LDAC, respectively. The 8xC51 provides the LSB of its SBUF register as the first bit in the data stream. The user must ensure that the data in the SBUF register is arranged correctly because the DAC expects MSB first. 8xC51* AD5570* RxD SDIN TxD SCLK P3.3 SYNC P3.4 LDAC *ADDITIONAL PINS OMITTED FOR CLARITY. Figure 43. AD5570 to 8xC51 Interface When data is to be transmitted to the DAC, P3.3 is taken low. Data on RxD is clocked out of the microcontroller on the rising edge of TxD and is valid on the falling edge. As a result, no glue logic is required between this DAC and the microcontroller interface. 03760-014 MISO MOSI AD5570 to 8xC51 Interface The 8xC51 transmits data in 8-bit bytes with only eight falling clock edges occurring in the transmit cycle. Because the DAC expects a 16-bit word, SYNC (P3.3) must be left low after the first eight bits are transferred. After the second byte has been transferred, the P3.3 line is taken high. The DAC can be updated using LDAC via P3.4 of the 8xC51. AD5570* MC68HC11* LDAC is controlled by the PC6 port output. The DAC can be updated after each 2-byte transfer by bringing LDAC low. This example does not show other serial lines for the DAC. If CLR were used, control it by the Port Output PC5. 03760-015 MICROPROCESSOR INTERFACING Figure 42. AD5570 to MC68HC11 Interface Rev. B | Page 21 of 24 AD5570 An interface between the AD5570 and the ADSP21xx family is shown in Figure 44. The ADSP21xx must be set up to operate in the SPORT transmit alternate framing mode. The ADSP21xx is programmed through the SPORT control register and is configured as follows: internal clock operation, active low framing, and 16-bit word length. Transmission is initiated by writing a word to the Tx register, after the SPORT has been enabled. As the data is clocked out of the DSP on the rising edge of SCLK, no glue logic is required to interface the DSP to the DAC. In the interface shown, the DAC output is updated using the LDAC pin via the DSP. Alternatively, the LDAC input can be tied permanently low, and then the update is automatic when TFS is taken high. ADSP21xx SDO DT SDIN SCLK SYNC LDAC *ADDITIONAL PINS OMITTED FOR CLARITY. 03760-016 FO SDI/RC4 SDO SDO/RC5 SDIN SCLK/RC3 SCLK RA1 SYNC *ADDITIONAL PINS OMITTED FOR CLARITY. Figure 45. AD5570 to PIC16C6x/7x Interface EVALUATION BOARD The AD5570 evaluation kit includes a populated and tested AD5570 printed circuit board. The evaluation board interfaces to the parallel interface of a PC. Software is available with the evaluation board that allows the user to easily program the AD5570. A schematic of the evaluation board is shown in Figure 46. The software runs on any PC installed with Microsoft(R) Windows(R) 95/ Windows(R) 98/Windows(R) ME/ Windows(R) 2000/Windows(R) XP. SCLK TFS RFS AD5570* PIC16C6x/7x* The AD5570 comes with a full evaluation board to aid designers in evaluating the high performance of the part with minimal effort. The evaluation board requires a power supply, a PC, and an oscilloscope. AD5570* DR eight bits of data during each serial transfer operation; therefore, two consecutive write operations are needed. Figure 45 shows the connection diagram. 03760-017 AD5570 to ADSP21xx Figure 44. AD5570 to ADSP21xx Interface AD5570 to PIC16C6x/7x The PIC16C6x/7x synchronous serial port (SSP) is configured as an SPI master with the clock polarity bit set to 0. This is done by writing to the synchronous serial port control register, SSPCON (see documentation on the PIC16/17 microcontroller). In this example, I/O port RA1 is being used to pulse SYNC and enable the serial port of the AD5570. This microcontroller transfers only An application note containing full details on operating the evaluation board comes supplied with the AD5570 evaluation board. Rev. B | Page 22 of 24 Figure 46. Evaluation Board Schematic SCLK_ADC SDATA_ADC DATA SYNC LDAC CLR CONVST DIN SCLK PD J11-30 J11-29 J11-28 J11-27 J11-26 J11-25 J11-24 J11-23 J11-22 J11-21 J11-20 J11-19 J11-9 J11-10 J11-12 J11-4 J11-6 J11-7 J11-8 J11-2 J11-5 J11-3 J11-13 J12-3 + + PD + C30 10F 20V J5 J7 DVDD J8 + + DGND J9 LK4 VSS + + + C13 C21 C22 C23 C24 C15 10F 10F 10F 0.1F 0.1F 0.1F A0 A1 A2 A3 OE 0.33F C2 74ACT244 AVDD VSS AGND Y0 Y1 Y2 Y3 2 4 6 8 1 9 7 5 3 74ACT244 A0 A1 A2 A3 OE U9-B 74ACT244 A0 A1 A2 A3 11 A0 A1 13 15 A2 17 A3 OE 19 74ACT244 VIN VOUT U6 GND4 GND2 GND3 GND1 AVDD 5 6 7 8 4 3 2 1 C17 0.1F + C18 10F PD SDO SDIN SCLK SYNC LDAC CLR 9 3 REF/2 2 4 VSS V- OP177 7 V+ 13 + C5 10F C3 0.1F VOUT REF/2 6 C36 0.1F OP 6 +VIN GND 4 U2 TRIM ADR435 VOUT 5 2 REF TP5 R1 WHITE PLASTIC SSOP CLAMP C16 0.1F LK3 C35 0.1F 15 U1 + C34 10F TP4 16 14 REFGND U3 AVDD VIN AGND 3 2 12 11 1 J2 AD5570 2 1 VSS AVDD C4 0.01F AD7895-10 U5 8 4 SCLK 5 SDATA 6 BUSY 7 CONVST DGND LK2 LK1 10 8 7 6 5 4 3 TP8 TP3 TP9 TP2 TP1 TP7 TP10 AVDD LM78L05ACM U4-B Y0 Y1 Y2 Y3 9 7 5 3 18 Y0 Y1 16 14 Y2 12 Y3 U9-A OE U4-A 11 13 15 17 19 2 4 6 8 1 18 Y0 16 Y1 14 Y2 12 Y3 J10 SCLK LDAC SYNC CLR C31 C32 C33 0.1F 0.1F 0.1F J6 DIN C12 C11 C10 C9 C8 C7 C6 C14 10F 10F 10F 10F 0.1F 0.1F 0.1F 0.1F AGND J12-2 J12-1 AVDD J13-2 DGND J13-1 DVDD J4 SDO DVDD DVDD DVDD R5 4.7k DOUT R4 4.7k R7 4.7k J11 - CENTRONICS CONNECTOR R6 4.7k VSS DGND VDD AGND REFIN REFGND REF LK5 VDD AGNDS REFIN GND Rev. B | Page 23 of 24 C1 AVDD R3 10k R2 10k J1 REF/2 VOUT 03760-043 DVDD AD5570 AD5570 OUTLINE DIMENSIONS 6.50 6.20 5.90 9 5.60 5.30 5.00 1 8 0.25 0.09 1.85 1.75 1.65 2.00 MAX 0.05 MIN COPLANARITY 0.10 8.20 7.80 7.40 0.65 BSC 0.38 0.22 SEATING PLANE 8 4 0 COMPLIANT TO JEDEC STANDARDS MO-150-AC 0.95 0.75 0.55 060106-A 16 Figure 47. 16-Lead Shrink Small Outline Package [SSOP] (RS-16) Dimensions shown in millimeters ORDERING GUIDE Model AD5570ARS AD5570ARS-REEL AD5570ARS-REEL7 AD5570ARSZ 1 AD5570ARSZ-REEL1 AD5570ARSZ-REEL71 AD5570BRS AD5570BRS-REEL AD5570BRS-REEL7 AD5570BRSZ1 AD5570BRSZ-REEL1 AD5570BRSZ-REEL71 AD5570WRS AD5570WRS-REEL AD5570WRS-REEL7 AD5570WRSZ1 AD5570WRSZ-REEL1 AD5570WRSZ-REEL71 AD5570YRS AD5570YRS-REEL AD5570YRS-REEL7 AD5570YRSZ1 AD5570YRSZ-REEL1 AD5560YRSZ-REEL71 EVAL-AD5570EB 1 Temperature Range -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +85C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C Package Description 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP 16-Lead SSOP Evaluation Board Z = Pb-free part. (c)2006 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C03760-0-9/06(B) Rev. B | Page 24 of 24 Package Option RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16 RS-16