Only One Name Means ProTek’Tion™
The PSRDAxx-6 Series are low capacitance mul-line steering diode/transient voltage suppressor arrays that provides
board level protecon for standard TTL and CMOS bus line applicaons against the damaging eects of ESD, terary
lightning and switching transients.
The PSRDAxx-6 Series has a peak pulse power rang of 500 Was for an 8/20µs waveshape. This device series meets
the IEC 61000-4-2, IEC 61000-4-4 and IEC 61000-4-5 requirements.
• Compable with IEC 61000-4-2 (ESD): Air - 15kV, Contact - 8kV
• Compable with IEC 61000-4-4 (EFT): 40A - 5/50ns
• Compable with IEC 61000-4-5 (Surge): 24A, 8/20µs - Level 2(Line-
Gnd) & Level 3(Line-Line)
• 500 Was Peak Pulse Power per Line (tp = 8/20µs)
• Bidireconal Conguraon
• Available in 3.3V and 5V
• Protects Up to Six Lines
• Ultra Low Capacitance: 5pF
• RoHS Compliant
• REACH Compliant
• Molded JEDEC SO-8 Package
• Approximate Weight: 70 milligrams
• Lead-Free Pure-Tin Plang (Annealed)
• Solder Reow Temperature:
Pure-Tin - Sn, 100: 260-270°C
• 12mm Tape and Reel Per EIA Standard 481
• Flammability Rang UL 94V-0
• Computer Interface Protecon
• Ethernet - 10/100/1000 Base T
• Set-Top Box Protecon
• Industrial Controls
1 2 4
8
3
567
GND I/O 6 I/O 5 I/O 4
I/O 3+VREF
I/O 2I/O 1
Only One Name Means ProTek’Tion™
Peak Pulse Power (tp = 8/20µs) - See Figure 1 PPP 500 Was
Operang Temperature TL-55 to 150 °C
Storage Temperature TSTG -55 to 150 °C
Connuous Power Dissipaon PPC 1000 mW
Maximum Forward Voltage @ 10mA (Note 1) VF1.1 Volts
1. Measured between pins 8 to 1, 2, 3, 4, 5, 6 or 7.
PSRDA3.3-6 SGG 3.3 4.0 6.5 125 5
PSRDA05-6 SGH 5.0 6.0 9.8 20 5
1. Capacitance measured at VWM = VCC connected between I/O pins to pin 8 (Gnd). VR = VWM @ 1MHz. As shown in Figure 6, REF1 is connected to ground, REF2 is connected to +VCC, and
input applies to VCC = 5V, VSIGN = 30mV, F = 1MHz
500W, 8/20µs Waveform
Only One Name Means ProTek’Tion™
Peak Pulse Power
8/20µs
Average Power
TEST
WAVEFORM
PARAMETERS
tf = 8µs
td = 20µs
tf
e-t
Peak Value IPP
td = t/(IPP/2)
Only One Name Means ProTek’Tion™
G
REF1
+VCC
VSIGN
REF2
I/O
Only One Name Means ProTek’Tion™
BV V See Table 2 200
IBV µA 1 0.01
Cjo pF See Table 2 5
ISA See Table 2 1E-13
Vj V 0.6 0.6
M - 0.33 0.33
N - 1 1
RSOhms See Table 2 0.31
TT s 1E-8 1E-9
EG eV 1.11 1.11
PSRDA3.3-6 4.0 438 1E-11 0.21
PSRDA05-6 6.0 284 1E-11 0.14
ABD - Avalanche Breakdown Diode (TVS)
LCRD: Low Capacitance Recer Diode
Lg - Lead Inductance
Lg
0.7nH
LCRD
I/O ABD
LCRD
VCC
Only One Name Means ProTek’Tion™
Circuit connecvity is as follows:
• Pins 1, 2, 4, 5, 6 and 7 connected to the datalines.
• Pin 8 connected to ground.
• Pin 3 connected to the databus.
Circuit board layout is crical for electromagnec compability protecon. The following guidelines are recommended:
• The protecon device should be placed near the input terminals or connectors, the device will divert the transient current
immediately before it can be coupled into the nearby traces.
• The path length between the TVS device and the protected line should be minimized.
• All conducve loops including power and ground loops should be minimized.
• The transient current return path to ground should be kept as short as possible to reduce parasic inductance.
• Ground planes should be used whenever possible. For mullayer PCBs, use ground vias.
1 2 4
8
3
567
VBUS
VBUS
D+
D+
D-
D-
GND
GND
USB Port
USB Port
VBUS
D+
D-
GND
USB Port
USB Controller
Only One Name Means ProTek’Tion™
A 4.80 5.00 0.189 0.196
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G 1.27 BSC 0.05 BSC
J 0.18 0.25 0.007 0.009
K 0.10 0.25 0.004 0.008
P 5.80 6.20 0.229 0.244
R 0.25 0.50 0.010 0.019
1. -T- = Seang plane and datum surface.
2. Dimensions “A” and “B” are datum.
3. Dimensions “A” and “B” do not include mold protrusion.
4. Maximum mold protrusion is 0.015” (0.380mm) per side.
5. Dimensioning and tolerances per ANSI Y14.5M, 1982.
6. Dimensions are exclusive of mold ash and metal burrs.
A 1.14 1.40 0.045 0.055
B 0.64 0.89 0.025 0.035
C 6.22 - 0.245 -
D 3.94 4.17 0.155 0.165
E 1.02 1.27 0.040 0.050
1. Controlling dimension: inches.
-A-
8 5
14
-B- P
GD
-T-
C
K J
R x 45°
0° - 10°
F
4 PL
0.010” (0.25mm) MB
+
8 PL
0.010” (0.25mm) B
+AT
A
B
CD
E
M
MSS
Only One Name Means ProTek’Tion™
User Direcon of Feed
t
K0
A0 P
D
P0
P2 E
B0
F
W
10 Pitches Cumulave
Tolerance on tape ± 0.2
Pin 1
178mm (7”) 12mm 6.50 ± 0.10 5.40 ± 0.10 2.00 ± 0.10 1.50 ± 0.10 1.75 ± 0.10 5.50 ± 0.05 12.00 ± 0.30 4.00 ± 0.12 2.00 ± 0.10 4.00 ± 0.10 0.25
1. Dimensions are in millimeters.
2. Surface mount product is taped and reeled in accordance with EIA-481.
3. Sux - T7 = 7” Reel - 1,000 pieces per 12mm tape.
4. Sux - T13 = 13” Reel - 2,500 pieces per 12mm tape.
5. Bulk product shipped in tubes of 98 pieces per tube.
6. Marking on Part - marking code (see page 2), date code, logo and pin one dened by dot on top of package.
Package outline, pad layout and tape specicaons per document number 06011.R4 8/10.
PSRDAxx-6 -LF -T7 1,000 7” 98
PSRDAxx-6 -LF -T13 2,500 13” 98
Only One Name Means ProTek’Tion™
ProTek Devices, based in Tempe, Arizona USA, is a manufacturer of Transient Voltage Suppression (TVS) products designed specically for
the protecon of electronic systems from the eects of lightning, Electrostac Discharge (ESD), Nuclear Electromagnec Pulse (NEMP), in-
ducve switching and EMI/RFI. With over 25 years of engineering and manufacturing experience, ProTek designs TVS devices that provide
applicaon specic protecon soluons for all electronic equipment/systems.
ProTek Devices Analog Products Division, also manufactures analog interface, control, RF and power management products.
COPYRIGHT © ProTek Devices 2007 - This literature is subject to all applicable copyright laws and is not for resale in any manner.
SPECIFICATIONS: ProTek reserves the right to change the electrical and or mechanical characteriscs described herein without noce.
DESIGN CHANGES: ProTek reserves the right to disconnue product lines without noce and that the nal judgement concerning selecon and specicaons is the buyer’s and that in furnishing engineering
and technical assistance. ProTek assumes no responsibility with respect to the selecon or specicaons of such products. ProTek makes no warranty, representaon or guarantee regarding the suitability of
its products for any parcular purpose, nor does ProTek assume any liability arising out of the applicaon or use of any product or circuit and specically disclaims any and all liability without limitaon special,
consequenal or incidental damages.
LIFE SUPPORT POLICY: ProTek Devices products are not authorized for use in life support systems without wrien consent from the factory.
2929 South Fair Lane
Tempe, Arizona 85282
USA
General: 602-431-8101
Sales: 602-414-5109
Customer Service: 602-414-5114
General: 602-431-2288
Sales: sales@protekdevices.com
Customer Service: service@protekdevices.com
Technical Support: support@protekdevices.com
www.protekdevices.com
www.protekanalog.com
