AS4SD4M16DGC-10/XT - Micross Components, Inc.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

FEATURES

• Full Military temp (-55°C to 125°C) processing available

• Copper lead frame option for enhanced reliability

• WRITE Recovery ( tWR/ tDPL) tWR = 2 CLK

• Fully synchronous; all signals registered on positive

edge of system clock

• Internal pipelined operation; column address can be

changed every clock cycle

• Internal banks for hiding row access/precharge

• Programmable burst lengths: 1, 2, 4, 8 or full page

• Auto Precharge and Auto Refresh Modes

• Self Refresh Mode (IT & ET)

• 4,096-cycle refresh

• LVTTL-compatible inputs and outputs

• Single +3.3V ±0.3V power supply

• Longer lead TSOP for improved reliability (OCPL*)

OPTIONS MARKING

• Conﬁ gurations

4 Meg x 16 (1 Meg x 16 x 4 banks) 4M16

• Plastic Package – 54-pin TSOPII (400 mil)

- Alloy 42 lead frame - OCPL* DG No. 901

- Copper lead frame DGC

(Pb/Sn ﬁ nish or RoHS available)

• Timing (Cycle Time)

8ns; tAC = 6.5ns @ CL = 3 ( tRP - 24ns) -8

10ns; tAC = 9ns @ CL = 2 -10

• Operating Temperature Ranges

-Industrial Temp (-40°C to 85° C) IT

-Enhanced Temp (-40°C to +105°C) ET

-Military Temp (-55°C to 125°C) XT

KEY TIMING PARAMETERS

SPEED CLOCK SETUP HOLD

GRADE FREQUENCY

CL = 2** CL = 3**

TIME TIME

-8 125 MHz – 6.5ns 2ns 1ns

-10 100 MHz – 7ns 3ns 1ns

-8 83 MHz 9ns – 2ns 1ns

-10 66 MHz 9ns – 3ns 1ns

ACCESS TIME

*Off-center parting line

**CL = CAS (READ) latency

PIN ASSIGNMENT

(Top View)

54-Pin TSOP

Note: “\” indicates an active low.

Configuration 1 Meg x 16 x 4 banks

Refresh Count 4K

Row Addressing 4K (A0-A11)

Bank Addressing 4 (BA0, BA1)

Column Addressing 256 (A0-A7)

4 Meg x 16

4 Meg x 16 SDRAM

Synchronous DRAM Memory

For more products and information

please visit our web site at

www.micross.com

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

GENERAL DESCRIPTION

The 64Mb SDRAM is a high-speed CMOS, dynamic ran-

dom-access memory containing 67,108,864 bits. It is internally

conﬁ gured as a quad-bank DRAM with a synchronous interface

(all signals are registered on the positive edge of the clock signal,

CLK). Each of the x16’s 6,777,216-bit banks is organized as

4,096 rows by 256 columns by 16 bits.

Read and write accesses to the SDRAM are burst oriented;

accesses start at a selected location and continue for a programmed

number of locations in a programmed sequence. Accesses begin

with the registration of an ACTIVE command, which is then fol-

lowed by a READ or WRITE command. The address bits registered

coincident with the ACTIVE command are used to select the bank

and row to be accessed (BA0, BA1 select the bank; A0-A1 1 select

the row). The address bits registered coincident with the READ or

WRITE command are used to select the starting column location

for the burst access.

The SDRAM provides for programmable READ or WRITE

burst lengths of 1, 2, 4 or 8 locations, or the full page, with a burst

terminate option. An AUTO PRECHARGE function may be en-

abled to provide a self-timed row precharge that is initiated at the

end of the burst sequence.

The 64Mb SDRAM uses an internal pipelined architecture

to achieve high-speed operation. This architecture is compatible

with the 2n rule of prefetch architectures, but it also allows the

column address to be changed on every clock cycle to achieve a

high-speed, fully random access. Precharging one bank while ac-

cessing one of the other three banks will hide the precharge cycles

and provide seamless, high-speed, random-access operation.

The 64Mb SDRAM is designed to operate in 3.3V, low-power

memory systems. An auto refresh mode is provided, along with

a power-saving, power-down mode. All inputs and outputs are

LVTTL-compatible.

SDRAMs offer substantial advances in DRAM operating

performance, including the ability to synchronously burst data at a

high data rate with automatic column-address generation, the abil-

ity to interleave between internal banks in order to hide precharge

time and the capability to randomly change column addresses on

each clock cycle during a burst access.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

CKE

CLK

CS\

WE\

CAS\

RAS\

DQML, DQMH

DQ0-DQ15

A0,

A10,

12 12

ROW

ADDRESS

MUX

ADDRESS

REFRESH

COUNTER

CONTROL

LOGIC

COMMAND

DECODE

MODE REGISTER

DATA

OUTPUT

DATA

INPUT

BANK0

ROW-

ADDRESS

LATCH &

DECODER

BANK 0

MEMORY

ARRAY

(4,096 X 256 X 16)

SENSE AMPLIFIERS

4096

I/O GATING

DQM MASK LOGIC

READ DATA LATCH

WRITE DRIVERS

4096

COLUMN

DECODER

256

(X16)

BANK

CONTROL

LOGIC

COLUMN-

ADDRESS

COUNTER/

LATCH

BANK1 BANK2 BANK3

2 2

FUNCTIONAL BLOCK DIAGRAM

4 Meg x 16 SDRAM

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

ENHANCING RELIABILITY WITH COPPER LEAD FRAMES1

ADVANTAGES & BENEFITS

Superior thermal conductivity improvement: 170 W/m*K •

vs. 14 W/m*K (a 12X difference).

θ ja and θ jc characteristics provide up to 3.8X advantage •

of heat dissipation capability versus parts with alloy 42

lead frames.

Heat dissipated from the die faster makes it run cooler •

leading to longer life.

Solder joint reliability vastly improved.•

- CTE of Copper (17 ppm/ oC), matches the CTE of Typical

FR4 PWBs (15-17 ppm/ oC)

- CTE of Alloy 42 (5 ppm/ oC), mismatch to CTE of FR4

PWBs (15-17 ppm/ oC)

RoHS Version (NiPdAu plating)•

- Most preferred for elimination of risk for whisker growth.

The use of copper lead frames inherently allow for better solder joint reliability, tin whisker prevention and

better thermal dissipation. These are three big factors in overall system reliability over time.

Better Solder Joint Reliability

Many systems are expected to operate reliably over broad temperature variations spanning the industrial

(-400C to +850C) and military (-550C to +1250C) temperature ranges. System problems can be caused

by the mismatch of thermal coefﬁ cients of all system components. Better solder joint reliability is obtained

since the copper lead frame is more ﬂ exible, and the CTE of the copper lead frame is better matched with

that of typical FR4 PWBs, than that of Alloy 42. Repeated thermal cycles over a period of time can take a

toll on solder joints, causing cracks and intermittent connections where expansion and contraction of the

lead frame is at a different rate than the FR4 PWB that it is attached to.

Whisker Prevention

The RoHS version of this copper lead frame, with its’ NiPdAu (Nickel-Palladium-Gold) plating, eliminates

the risk of tin whiskers. Microscopic whiskers can grow on a parts’ pins than have tin content in the plat-

ing. Traditionally Alloy 42 lead frames have a Sn or PbSn plating. This plating containing tin, along with

certain environmental conditions can cause these whiskers to grow. Their growth may extend to form a

bridge with another pin on the device, or the whisker may break off and cause a short circuit or even an

explosive power surge on the board. The organization, iNEMI (International Electronics Manufacturing

Initiative) lists the NiPdAu lead plating as the most preferred for elimination of risk for whiskers.

Better Thermal Dissipation

Because copper has a 10X to 12X improvement in thermal conductivity vs. Alloy 42, and since θ ja and θ jc

characteristics of copper provide up to 3.8X advantage over Alloy 42, more efﬁ cient thermal dissipation is

the result. This translates to better heat dissipated away from the chip through the lead frame and PWB,

thus extending the useful life of the die by reducing die junction temperature. Therefore less heat stress

remains in the device, which is a leading cause of non-mechanical failure in a long life application.

1Source: ISSI white paper; “Enhancing Long-Term Reliability with Copper Lead Frames.”

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

ENHANCING RELIABILITY WITH COPPER LEAD FRAMES

Thermal Impedance Data - Cu LF vs. Alloy 42, 54 Lead TSOP II

With copper lead frames, the die stays cooler, and results in greater component

reliability and longer life. This equates to improved system reliability and lower

service costs and greater system quality conﬁ dence.

CuLF CuLF Alloy42LF Alloy42LF Alloy42LF

ȺͲja ȺͲjc ȺͲja ȺͲja ȺͲjc ȺͲja ȺͲjc

oC/Watt oC/Watt oC/Watt oC/Watt oC/Watt CuLFAdvantage CuLFAdvantage

2ͲLayer 4ͲLayer

64M 62 9 99.1 70.5 13.7 1.6X 1.5X

128M 53 7.8 86.2 58.9 11.3 1.6X 1.4X

256M 32.3 2.7 81 44 10.3 2.5X 3.8X

512M 25.2 2.8 62.6 39.2 6.7 2.5X 2.4X

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

PIN DESCRIPTION

TSOP

PIN NUMBERS

38 CLK Input Clock: CLK is driven by the system clock. All SDRAM input signals are

sampled on the positive edge of CLK. CLK also increments the internal burst

counter and controls the output registers.

37 CKE Input Clock Enable: CKE activates (HIGH) and deactivates (LOW) the CLK signal.

Deactivating the clock provides PRECHARGE POWER-DOWN and SELF

REFRESH operations (all banks idle), ACTIVE POWER-DOWN (row ACTIVE

in either bank) or CLOCK SUSPEND operation (burst/access in progress).

CKE is synchronous except after the device enters power-down and self

refresh modes, where CKE becomes asynchronous until after exiting the

same mode. The input buffers, including CLK, are disabled during power-down

and self refresh modes, providing low standby power. CKE may be tied

HIGH.

19 CS\ Input Chip Select: CS\ enables (registered LOW) and disables (registered HIGH)

the command decoder. All commands are masked when CS\ is registered

HIGH. CS\ provides for external bank selection on systems with multiple

banks. CS\ is considered part of the command code.

16, 17 WE\, CAS\ Input Command Inputs: RAS\, CAS\, and WE\ (along with CS\) define the

18 RAS\ command being entered.

15, 39 DQML, Input Input/Output Mask: DQM is an input mask signal for write accesses and an

DQMH output enable signal for read accesses. Input data is masked when DQM is

sampled HIGH during a WRITE cycle. The output buffers are placed in a

High-Z state (two-clock latency) when DQM is sampled HIGH during a READ

cycle. DQML corresponds to DQ0-DQ7; DQMH corresponds to DQ8-DQ15.

DQML and DQMH are considered same state when referenced as DQM.

20, 21 BA0, BA1 Input Bank Address Inputs: BA0 and BA1 define to which bank the ACTIVE, READ,

WRITE or PRECHARGE command is being applied.

23-26, 29-34, A0-A11 Input Address Inputs: A0-A11 are sampled during the ACTIVE command (row

22, 35 address A0-A11) and READ/WRITE command (column address A0-A7, with

A10 defining AUTO PRECHARGE) to select one location out of the memory

array in the respective bank. A10 is sampled during a PRECHARGE

command to determine if all banks are to be precharged (A10 HIGH) or bank

selected by BA0,BA1 (LOW). The address inputs also provide the op-code

during a LOAD MODE REGISTER command.

2, 4, 5, 7, 8 DQ0- DQ15 Input/ Data I/O: Data bus.

10, 11, 13, 42 Output

44, 45, 47, 48

50, 51, 53

36, 40 NC — No Connect: These pins should be left unconnected.

3, 9, 43, 49 VDDQ Supply DQ Power: Provide isolated power to DQs for improved noise immunity.

6, 12, 46, 52 VSSQ Supply DQ Ground: Provide isolated ground to DQs for improved noise immunity.

1, 14, 27 VDD Supply Power Supply: +3.3V ±0.3V.

28, 41, 54 VSS Supply Ground.

SYMBOL TYPE DESCRIPTION

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

FUNCTIONAL DESCRIPTION

In general, the 64Mb SDRAM is quad-bank DRAM (1

Meg x 16 x 4 banks) which operate at 3.3V and include a synchro-

nous interface (all signals are registered on the positive edge of

the clock signal, CLK). Each of the x16’s 16,777,216-bit banks

is organized as 4,096 rows by 256 columns by 16 bits.

Read and write accesses to the SDRAM are burst ori-

ented; accesses start at a selected location and continue for a

programmed number of locations in a programmed sequence. Ac-

cesses begin with the registration of an ACTIVE command which

is then followed by a READ or WRITE command. The address

bits registered coincident with the ACTIVE command are used

to select the bank and row to be accessed (BA0 and BA1 select

the bank, A0-A11 select the row). The address bits ( x16: A0-A7)

registered coincident with the READ or WRITE command are

used to select the starting column location for the burst access.

Prior to normal operation, the SDRAM must be initial-

ized. The following sections provide detailed information cover-

ing device initialization, register deﬁ nition, command descrip-

tions and device operation.

Initalization

SDRAMs must be powered up and initialized in a pre-

deﬁ ned manner . Operational procedures other than those speciﬁ ed

may result in undeﬁ ned operation. Once power is applied to VDD

and VDDQ (simultaneously) and the clock is stable, the SDRAM

requires a 100μs delay prior to applying an executable command.

Starting at some point during this 100μs period and continuing

at least through the end of this period, COMMAND INHIBIT or

NOP commands should be applied.

Once the 100μs delay has been satisﬁ ed with at least one

COMMAND INHIBIT or NOP command having been applied,

a PRECHARGE command should be applied. All banks must be

precharged, thereby placing the device in the all banks idle state.

Once in the idle state, two AUTO REFRESH cycles must

be performed. After the AUTO REFRESH cycles are complete,

the SDRAM is ready for Mode Register programming. Because

the Mode Register will power up in an unknown state, it should

be loaded prior to applying any operational command.

Mode Register

The Mode Register is used to deﬁ ne the speciﬁ c mode of

operation of the SDRAM. This deﬁ nition includes the selection of

a burst length, a burst type, a CAS latency , an operating mode and

a write burst mode, as shown in Figure 1. The Mode Register is

programmed via the LOAD MODE REGISTER command and

will retain the stored information until it is programmed again or

the device loses power.

Mode register bits M0-M2 specify the burst length, M3

speciﬁ es the type of burst (sequential or interleaved), M4-M6

specify the CAS latency, M7 and M8 specify the operating mode,

M9 speciﬁ es the WRITE burst mode, and M10 and M11 are re-

served for future use.

The Mode Register must be loaded when all banks are

idle, and the controller must wait the speciﬁ ed time before initiat-

ing the subsequent operation. V iolating either of these requirements

will result in unspeciﬁ ed operation.

Burst Length

Read and write accesses to the SDRAM are burst ori-

ented, with the burst length being programmable, as shown in

Figure 1. The burst length determines the maximum number of

column locations that can be accessed for a given READ or WRITE

command. Burst lengths of 1, 2, 4, or 8 locations are available for

both the sequential and the interleaved burst types, and a full-page

burst is available for the sequential type. The full-page burst is

used in conjunction with the BURST TERMINATE command to

generate arbitrary burst lengths.

Reserved states should not be used, as unknown opera-

tion or incompatibility with future versions may result.

When a READ or WRITE command is issued, a block

of columns equal to the burst length is effectively selected. All

accesses for that burst take place within this block, meaning that

the burst will wrap within the block if a boundary is reached. The

block is uniquely selected by A1-A7 (x16) when the burst length is

set to two; A2-A7 (x16) when the burst length is set to four; and by

A3-A7 (x16) when the burst length is set to eight. The remaining

(least signiﬁ cant) address bit(s) is (are) used to select the starting

location within the block. Full-page bursts wrap within the page

if the boundary is reached.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

e = Se

uential T

e = Interleaved

0 0 - 1 0 - 1

11-0 1-0

A1 A0

0 0 0,1,2,3 0,1,2,3

0 1 1,2,3,0 1,0,3,2

1 0 2,3,0,1 2,3,0,1

1 1 3,0,1,2 3,2,1,0

A2 A1 A0

0 0 0 0,1,2,3,4,5,6,7 0,1,2,3,4,5,6,7

0 0 1 1,2,3,4,5,6,7,0 1,0,3,2,5,4,7,6

0 1 0 2,3,4,5,6,7,0,1 2,3,0,1,6,7,4,5

0 1 1 3,4,5,6,7,0,1,2 3,2,1,0,7,6,5,4

1 0 0 4,5,6,7,0,1,2,3 4,5,6,7,0,1,2,3

1 0 1 5,6,7,0,1,2,3,4 5,4,7,6,1,0,3,2

1 1 0 6,7,0,1,2,3,4,5, 6,7,4,5,2,3,0,1

1 1 1 7,0,1,2,3,4,5,6 7,6,5,4,3,2,1,0

Cn, Cn+1, Cn+2,

Cn+3, Cn+4… Not Supported

…Cn-1,

Cn…

BURST DEFINITION

Table 1

Full Page

(y)

n = A0 - A9

location 0 - y

Order of Access Within a Burst

Burst

Length

Starting Column

Address

A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 Address Bus

M3=0 M3=1

000 1 1

001 2 2

010 4 4

011 8 8

1 0 0 Reserved Reserved

1 0 1 Reserved Reserved

1 1 0 Reserved Reserved

1 1 1 Full Page Reserved

M6 M5 M4

000

001

010

011

100

101

110

111

M8 M7

Reserved

Burst Type

Sequential

* Should program M11,

M10=0,0 to ensure

compatibility with future

devices.

CAS Latency

Single Location Access

M6 - M0

Defined

Operating Mode

Standard Operation

All other states reserved

Write Burst Mode

Programmed Burst Length

Interleave

Mode Register(Mx)

Burst Length

M2 M1 M0

11 10 9 8 7 6 5 4 3 2 1 0

Reserved* WB Op Mode CAS Latency BT Burst Length

BURST TYPE

Accesses within a given burst may be programmed to be

either sequential or interleaved; this is referred to as the burst type

and is selected via bit M3.

The ordering of accesses within a burst is determined by

the burst length, the burst type and the starting column address, as

shown in Table 1.

NOTE:

1. For full-page accesses: y = 256 (x16).

2. For a burst length of two, A1-A7 (x16)

select the block-of-two burst; A0 selects

the starting column within the block.

3. For a burst length of four, A2-A7 (x16)

select the block-of-four burst; A0-A1 se-

lect the starting column within the block.

4. For a burst length of eight, A3-A7 (x16)

select the clock-of-eight burst; A0-A2 se-

lect the starting column within the block.

5. For a full-page burst, the full row is se-

lected and A0-A7 (x16) select the starting

column.

6. Whenever a boundary of the block is

reached within a given sequence above,

the following access wraps within the

block.

7. For a burst length of one, A0-A7 (x16)

select the unique column to be accessed,

and Mode Register bit M3 is ignored.

FIGURE 1

MODE REGISTER DEFINITION

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

CAS Latency

The CAS latency is the delay , in clock cycles, between

the registration of a READ command and the availability of

the ﬁ rst piece of output data. The latency can be set to two or

three clocks.

If a READ command is registered at clock edge n, and

the latency is m clocks, the data will be available by clock edge

n+m. The DQs will start driving as a result of the clock edge

one cycle earlier (n + m - 1), and provided that the relevant

access times are met, the data will be valid by clock edge n +

m. For example, assuming that the clock cycle time is such

that all relevant access times are met, if a READ command is

registered at T0 and the latency is programmed to two clocks,

the DQs will start driving after T1 and the data will be valid by

T2, as shown in Figure 2. T able 2 below indicates the operating

frequencies at which each CAS latency setting can be used.

Reserved states should not be used as unknown opera-

tion or incompatibility with future versions may result.

Operating Mode

The normal operating mode is selected by setting

M7and M8 to zero; the other combinations of values for M7

and M8 are reserved for future use and/or test modes. The

programmed burst length applies to both READ and WRITE

bursts.

Test modes and reserved states should not be used

because unknown operation or incompatibility with future

versions may result.

Write Burst Mode

When M9 = 0, the burst length programmed via M0-

M2 applies to both READ and WRITE bursts; when M9 = 1,

the programmed burst length applies to READ bursts, but write

accesses are single-location (nonburst) accesses.

CAS LATENCY = 2 CAS LATENCY = 3

-8 ≤ 83 ≤ 125

-10 ≤ 66 ≤ 100

SPEED

ALLOWABLE OPERATING FREQUENCY

(MHz)

CAS LATENCY

Table 2

Figure 2

CAS LATENCY

CLK

COMMAMD

T3T2T1

NOPREAD

DOUT

NOP

tLZ tOH

tAC

CAS Latency = 2

T4T3T2T1

NOP

READ NOP

DOUT

tAC

tLZ tOH

CAS Latency = 3

CLK

COMMAMD

DON’T CARE

UNDEFINED

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TRUTH TABLE 1- Commands and DMQ Operation

(Note: 1)

NAME (FUNCTION) CS\ RAS\ CAS\ WE\ DQM ADDR DQs NOTES

COMMAND INHIBIT (NOP) H X X X X X X

NO OPERATION (NOP) L H H H X X X

ACTIVE (select bank and activate row) L L H H X Bank/Row X 3

READ (select bank and column and start READ burst) L H L H X Bank/Col X 4

WRITE (select bank and column and start WRITE burst) L H L L X Bank/Col Valid 4

BURST TERMINATE L H H L X X Active

PRECHARGE (deactivate row in bank or banks) L L H L X Code X 5

LOAD MODE REGISTER L L L L X OpCode X 2

Write Enable/Output Enable - - - - L - Active 8

Write Inhibit/Output High-Z - - - - H - High-Z 8

X6,7LHX X

AUTO REFRESH or SELF REFRESH (enter self refresh

mode) LL

COMMANDS

T ruth Table 1 provides a quick reference of available commands.

This is followed by a written description of each command. Two

additional Truth Tables appear following the Operation section;

these tables provide current state/next state information.

NOTE:

1. CKE is HIGH for all commands shown except SELF REFRESH.

2. A0-A11 deﬁ ne the op-code written to the Mode Register.

3. A0-A11 provide row address, and BA0, BA1 determine which bank is made active.

4. A0-A7 (x16) provide column address; A10 HIGH enables the auto precharge feature (nonpersistent), while A10

LOW disables the auto precharge feature; BA0, BA1 determine which bank is being read from or written to.

5. A10 LOW: BA0, BA1 determine the bank being precharged. A10 HIGH: All banks precharged and BA0, BA1

are “Don’t Care.”

6. This command is AUTO REFRESH if CKE is HIGH; SELF REFRESH if CKE is LOW.

7. Internal refresh counter controls row addressing; all inputs and I/Os are “Don’t Care” except for CKE.

8. Activates or deactivates the DQs during WRITEs (zero-clock delay) and READs (two-clock delay).

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

COMMAND INHIBIT

The COMMAND INHIBIT function prevents new

commands from being executed by the SDRAM, regardless of

whether the CLK signal is enabled. The SDRAM is ef fectively

deselected. Operations already in progress are not affected.

NO OPERATION (NOP)

The NO OPERATION (NOP) command is used to

perform a NOP to an SDRAM which is selected (CS\ is LOW).

This prevents unwanted commands from being registered dur-

ing idle or wait states. Operations already in progress are not

affected.

LOAD MODE REGISTER

The Mode Register is loaded via inputs A0-A11. See

Mode Register heading in the Register Deﬁ nition section. The

LOAD MODE REGISTER command can only be issued when

all banks are idle, and a subsequent executable command cannot

be issued until tMRD is met.

ACTIVE

The ACTIVE command is used to open (or activate) a

row in a particular bank for a subsequent access. The value on

the BA0, BA1 inputs selects the bank, and the address provided

on inputs A0-A11 selects the row. This row remains active (or

open) for accesses until a PRECHARGE command is issued

to that bank. A PRECHARGE command must be issued before

opening a different row in the same bank.

READ

The READ command is used to initiate a burst read

access to an active row. The value on the BA0, BA1 inputs

selects the bank, and the address provided on inputs A0-A7

(x16) selects the starting column location. The value on input

A10 determines whether or not AUTO PRECHARGE is used.

If AUTO PRECHARGE is selected, the row being accessed

will be precharged at the end of the READ burst; if AUTO

PRECHARGE is not selected, the row will remain open for

subsequent accesses. Read data appears on the DQs subject to

the logic level on the DQM inputs two clocks earlier . If a given

DQM signal was registered HIGH, the corresponding DQs will

be High-Z two clocks later; if the DQM signal was registered

LOW, the DQs will provide valid data.

WRITE

The WRITE command is used to initiate a burst write

access to an active row. The value on the BA0, BA1 inputs

selects the bank, and the address provided on inputs A0-A7

(x16) selects the starting column location. The value on input

A10 determines whether or not AUTO PRECHARGE is used.

If AUTO PRECHARGE is selected, the row being accessed

will be precharged at the end of the WRITE burst; if AUTO

PRECHARGE is not selected, the row will remain open for

subsequent accesses. Input data appearing on the DQs is writ-

ten to the memory array subject to the DQM input logic level

appearing coincident with the data. If a given DQM signal

is registered LOW, the corresponding data will be written

to memory; if the DQM signal is registered HIGH, the cor-

responding data inputs will be ignored, and a WRITE will not

be executed to that byte/column location.

PRECHARGE

The PRECHARGE command is used to deactivate the

open row in a particular bank or the open row in all banks. The

bank(s) will be available for a subsequent row access a speciﬁ ed

time (tRP) after the PRECHARGE command is issued. Input

A10 determines whether one or all banks are to be precharged,

and in the case where only one bank is to be precharged, inputs

BA0, BA1 select the bank. Otherwise BA0, BA1 are treated

as “Don’t Care.” Once a bank has been prechar ged, it is in the

idle state and must be activated prior to any READ or WRITE

commands being issued to that bank.

AUTO PRECHARGE

AUTO PRECHARGE is a feature which performs the

same individual-bank PRECHARGE function described above,

without requiring an explicit command. This is accomplished

by using A10 to enable AUTO PRECHARGE in conjunction

with a speciﬁ c READ or WRITE command. A precharge of

the bank/row that is addressed with the READ or WRITE com-

mand is automatically performed upon completion of the READ

or WRITE burst, except in the full-page burst mode, where

AUTO PRECHARGE does not apply. AUTO PRECHARGE

is nonpersistent in that it is either enabled or disabled for each

individual READ or WRITE command.

AUTO PRECHARGE ensures that the precharge is

initiated at the earliest valid stage within a burst. The user must

not issue another command to the same bank until the precharge

time (tRP) is completed. This is determined as if an explicit

PRECHARGE command was issued at the earliest possible

time, as described for each burst type in the Operation section

of this data sheet.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

AUTO REFRESH

AUTO REFRESH is used during normal operation

of the SDRAM and is analagous to CAS\-BEFORE-RAS\

(CBR) REFRESH in conventional DRAMs. This command

is non- persistent, so it must be issued each time a refresh is

required.

The addressing is generated by the internal refresh

controller. This makes the address bits “Don’t Care” during

an AUTO REFRESH command. The 64Mb SDRAM requires

4,096 AUTO REFRESH cycles every 64ms *(tREF), regardless

of width option. Providing a distributed AUTO REFRESH

command every 15.625μs/3.906μs will meet the refresh re-

quirement and ensure that each row is refreshed. Alternatively ,

4,096 AUT O REFRESH commands can be issued in a burst at

the minimum cycle rate (tRC), once every 64ms/ 16ms (24ms

for XT).

SELF REFRESH (IT & ET ONLY)

The SELF REFRESH command can be used to retain

data in the SDRAM, even if the rest of the system is powered

down. When in the self refresh mode, the SDRAM retains data

without external clocking. The SELF REFRESH command is

initiated like an AUTO REFRESH command except CKE is

disabled (LOW).

Once the SELF REFRESH command is registered,

all the inputs to the SDRAM become “Don’t Care,” with the

exception of CKE, which must remain LOW.

Once self refresh mode is engaged, the SDRAM

provides its own internal clocking, causing it to perform its

own AUTO REFRESH cycles. The SDRAM must remain in

self refresh mode for a minimum period equal to tRAS and may

remain in self refresh mode for an indeﬁ nite period beyond

that.

The procedure for exiting self refresh requires a se-

quence of commands. First, CLK must be stable prior to CKE

going back HIGH. Once CKE is HIGH, the SDRAM must

have NOP commands issued (a minimum of two clocks) for

tXSR, because time is required for the completion of any internal

refresh in progress.

If during normal operation AUT O REFRESH cycles

are issued in bursts (as opposed to being evenly distributed),

a burst of 4,096 AUTO REFRESH cycles should be completed

just prior to entering and just after exiting the self refresh

mode.

The self refresh option is not available for the -55° to

+125° screening option.

*64ms for -40° to +85° C ( Industrial Temperatures) and 16ms for -55° to +125°C (Military Temperatures)

BURST TERMINATE

The BURST TERMINATE command is used to trun-

cate either ﬁ xed-length or full-page bursts. The most recently

registered READ or WRITE command prior to the BURST

TERMINATE command will be truncated, as shown in the

Operation section of this data sheet.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

OPERATION

BANK/ROW ACTIVATION

Before any READ or WRITE commands can be issued to

a bank within the SDRAM, a row in that bank must be “opened.”

This is accomplished via the ACTIVE command, which selects

both the bank and the row to be activated.

After opening a row (issuing an ACTIVE command), a

READ or WRITE command may be issued to that row, subject to

the tRCD speciﬁ cation. tRCD (MIN) should be divided by the clock

period and rounded up to the next whole number to determine the

earliest clock edge after the ACTIVE command on which a READ

or WRITE command can be entered. For example, a tRCD speciﬁ -

cation of 30ns with a 90 MHz clock (1 1.11ns period) results in 2.7

clocks, rounded to 3. This is reﬂ ected in Figure 4, which covers

any case where 2 < tRCD (MIN)/ tCK ≤ 3. (The same procedure is

used to convert other speciﬁ cation limits from time units to clock

cycles).

A subsequent ACTIVE command to a different row in

the same bank can only be issued after the previous active row has

been “closed” (precharged). The minimum time interval between

successive ACTIVE commands to the same bank is deﬁ ned by

tRC.

A subsequent ACTIVE command to another bank can

be issued while the ﬁ rst bank is being accessed, which results in a

reduction of total row-access overhead. The minimum time inter -

val between successive ACTIVE commands to dif ferent banks is

deﬁ ned by tRRD.

Figure 4

EXAMPLE: MEETING tRCD (MIN) WHEN 2<tRCD (MIN)/tCK<3

DON’T CARE

CLK

COMMAND

tRCD

ACTIVE NOP

T0 T1 T2 T3

NOP

READ or

WRITE

Figure 3

ACTIVATING A SPECIFIC ROW IN A

SPECIFIC BANK

CLK

CKE HIGH

CS\

RAS\

CAS\

WE\

A0-A11

BA0, 1

ROW ADDRESS

BANK ADDRESS

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

READs

READ bursts are initiated with a READ command, as shown in

Figure 5.

The starting column and bank addresses are provided

with the READ command, and AUTO PRECHARGE is either

enabled or disabled for that burst access. If AUT O PRECHARGE

is enabled, the row being accessed is precharged at the completion

of the burst. For the generic READ commands used in the follow-

ing illustrations, AUTO PRECHARGE is disabled.

During READ bursts, the valid data-out element from

the starting column address will be available following the CAS

latency after the READ command. Each subsequent data-out ele-

ment will be valid by the next positive clock edge. Figure 6 shows

general timing for each possible CAS latency setting.

Upon completion of a burst, assuming no other com-

mands have been initiated, the DQs will go High-Z. A full-page

burst will continue until terminated. (At the end of the page, it will

wrap to column 0 and continue.)

Data from any READ burst may be truncated with a

subsequent READ command, and data from a ﬁ xed-length READ

burst may be immediately followed by data from a READ com-

mand. In either case, a continuous ﬂ ow of data can be maintained.

The ﬁ rst data element from the new burst follows either the last

element of a completed burst or the last desired data element of

alonger burst which is being truncated. The new READ command

should be issued x cycles before the clock edge at which the last

desired data element is valid, where x equals the CAS latency

minus one.

Figure 5

READ COMMAND

CLK

CKE

CS\

WE\

A0-A7: x16

BA0, 1

COLUMN ADDRESS

BANK ADDRESS

ENABLE AUTO PRECHARGE

DISABLE AUTO PRECHARGE

A8, A9, A11: x16

A10

Figure 6

CAS LATENCY

DON’T CARE

UNDEFINED

CLK

COMMAND

tLZ tOH

tAC

CAS Latency = 3

NOP

DOUT

T0 T1 T2 T3

NOP

CLK

COMMAND

tLZ tOH

tAC

CAS Latency = 2

NOP

DOUT

T0 T1 T2 T3

NOP

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

This is shown in Figure 7 for CAS latencies of two and three;

data element n + 3 is either the last of a burst of four or the last

desired of a longer burst. The 64Mb SDRAM uses a pipelined

architecture and therefore does not require the 2n rule associated

with a prefetch architecture. A READ command can be initiated

on any clock cycle following a previous READ command. Full-

speed random read accesses can be performed to the same bank, as

shown in Figure 8, or each subsequent READ may be performed

to a different bank.

T0 T1 T2 T3 T4 T5

READ READ

NOP NOP NOP NOP

CLK

COMMAND

ADDRESS

NOP

BANK,

COL n

BANK,

COL b

X=1 cycle

CAS Latency = 2

Figure 7

CONSECUTIVE READ BURSTS

NOTE: Each READ command may be to either bank. DQM is LOW. DON’T CARE

T0 T1 T2 T3 T4 T5

READ READ

NOP NOP NOP NOP

CLK

COMMAND

ADDRESS

NOP

BANK,

COL n

BANK,

COL b

X=2 cycle

CAS Latency = 3

NOP

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

T0 T1 T2 T3 T4 T5

READ NOP

READ READ READ NOP

DOUT

CLK

COMMAND

ADDRESS

BANK,

COL n

BANK,

COL m

CAS Latency = 2

BANK,

COL a

BANK,

COL x

Figure 8

RANDOM READ ACCESSES

NOTE: Each READ command may be to either bank. DQM is LOW.

DON’T CARE

T0 T1 T2 T3 T4 T5

READ READ NOP

DOUT

CLK

COMMAND

ADDRESS

NOP

BANK,

COL n

BANK,

COL a

CAS Latency = 3

BANK,

COL x

BANK,

COL m

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

Data from any READ burst may be truncated with a subsequent

WRITE command, and data from a ﬁ xed-length READ burst

may be immediately followed by data from a WRITE command

(subject to bus turnaround limitations). The WRITE burst may

be initiated on the clock edge immediately following the last (or

last desired) data element from the READ burst, provided that

I/O contention can be avoided. In a given system design, there

may be a possibility that the device driving the input data will go

Low-Z before the SDRAM DQs go High-Z. In this case, at least

a single-cycle delay should occur between the last read data and

the WRITE command. The DQM input is used to avoid I/O con-

tention, as shown in Figures 9 and 10. The DQM signal must be

asserted (HIGH) at least two clocks prior to the WRITE command

(DQM latency is two clocks for output buffers) to suppress data-

out from the READ. Once the WRITE command is registered, the

DQs will go High-Z (or remain High-Z), regardless of the state of

the DQM signal. The DQM signal must be de-asserted prior to the

WRITE command (DQM latency is zero clocks for input buffers)

to ensure that the written data is not masked. Figure 9 shows the

case where the clock frequency allows for bus contention to be

avoided without adding a NOP cycle, and Figure 10 shows the

case where the additional NOP is needed.

Figure 10

READ TO WRITE WITH EXTRA

CLOCK CYCLE

NOTE: A CAS latency of three is used for illustration. The READ command may be to any

bank, and the WRITE command may be to any bank.

T0 T1 T2 T3 T4

READ NOP NOP NOP

BANK,

COL n

BANK,

COL b

DOUT nDIN b

CLK

COMMAND

ADDRESS

tHZ

tDS

NOP

DON’T CARE

DQM

Figure 9

READ TO WRITE

NOTE: A CAS latency of three is used for illustration. The READ command may be

to any bank, and the WRITE command may be to any bank. If a CAS latency of one is

used, the DQM is not required.

T0 T1 T2 T3 T4

READ NOP NOP NOP

BANK,

COL n

BANK,

COL b

DOUT nDIN b

CLK

COMMAND

ADDRESS

tHZ

tCK

tDS

DQM

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

A ﬁ xed-length READ burst may be followed by, or

truncated with, a PRECHARGE command to the same bank

(provided that AUTO PRECHARGE was not activated), and a

full-page burst maybe truncated with a PRECHARGE command

to the same bank. The PRECHARGE command should be issued x

cycles before the clock edge at which the last desired data element

is valid, where x equals the CAS latency minus one. This is shown

in Figure 1 1 for each possible CAS latency; data element n + 3 is

either the last of a burst of four or the last desired of a longer burst.

Following the PRECHARGE command, a subsequent command

to the same bank cannot be issued until tRP is met. Note that part

of the row precharge time is hidden during the access of the last

data element(s).

In the case of a ﬁ xed-length burst being executed to

completion, a PRECHARGE command issued at the optimum

time (as described above) provides the same operation that would

result from the same ﬁ xed-length burst

T0 T1 T2 T3 T4 T5

READ NOP PRE- NOP

CLK

COMMAND

ADDRESS

NOP

BANK a,

COL n

CAS Latency = 2

ACTIVE

NOP NOP

BANK

(a or all) BANK a,

ROW

tRP

X = 1 cycles

DOUT

n+1

DOUT

n+2

DOUT

n+3

Figure 11

READ TO PRECHARGE

NOTE: DQM is LOW.

DON’T CARE

T0 T1 T2 T3 T4 T5

READ NOP PRE- NOP

DOUT

n+1

DOUT

n+2

DOUT

n+3

CLK

COMMAND

ADDRESS

NOP

BANK a,

COL n

CAS Latency = 3

ACTIVE

NOP NOP

BANK

(a or all) BANK a,

ROW

tRP

X = 2 cycles

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

with AUTO PRECHARGE. The disadvantage of the PRECHARGE

command is that it requires that the command and address buses

be available at the appropriate time to issue the command; the

advantage of the PRECHARGE command is that it can be used

to truncate ﬁ xed-length or full-page bursts.

Full-page READ bursts can be truncated with the BURST

TERMINATE command, and ﬁ xed-length READ bursts may be

truncated with a BURST TERMINATE command, provided that

AUTO PRECHARGE was not activated. The BURST TERMI-

NATE command should be issued x cycles before the clock

edge at which the last desired data element is valid, where x equals

the CAS latency minus one. This is shown in Figure 12 for each

possible CAS latency; data element n + 3 is the last desired data

element of a longer burst.

T0 T1 T2 T3 T4 T5

READ NOP BURST TER-

MINATE NOP

CLK

COMMAND

ADDRESS

NOP

BANK,

COL n

CAS Latency = 2

NOP NOP

X = 1 cycles

DOUT

n+1 DOUT

n+2

DOUT

n+3

Figure 12

TERMINATING A READ BURST

NOTE: DQM is LOW.

DON’T CARE

T0 T1 T2 T3 T4 T5

READ NOP BURST TER-

MINATE NOP

DOUT

n+1

DOUT

n+2 DOUT

n+3

CLK

COMMAND

ADDRESS

NOP

BANK,

COL n

CAS Latency = 3

NOP

NOP NOP

X = 2 cycles

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

WRITEs

WRITE bursts are initiated with a WRITE command, as

shown in Figure 13.

The starting column and bank addresses are provided

with the WRITE command, and AUTO PRECHARGE is either

enabled or disabled for that access. If AUTO PRECHARGE is

enabled, the row being accessed is precharged at the completion of

the burst. For the generic WRITE commands used in the following

illustrations, AUTO PRECHARGE is disabled.

During WRITE bursts, the ﬁ rst valid data-in element will

be registered coincident with the WRITE command. Subsequent

data elements will be registered on each successive positive clock

edge. Upon completion of a ﬁ xed-length burst, assuming no other

commands have been initiated, the DQs will remain High-Z and

any additional input data will be ignored (see Figure 14). A full-

page burst will continue until terminated. (At the end of the page,

it will wrap to column 0 and continue.)

Data for any WRITE burst may be truncated with a subse-

quent WRITE command, and data for a ﬁ xed-length WRITE burst

may be immediately followed by data for a WRITE command. The

new WRITE command can be issued on any clock following the

previous WRITE command, and the data provided coincident with

the new command applies to the new command. An example is

shown in Figure 15. Data n + 1 is either the last of a burst of two

or the last desired of a longer burst. The 64Mb SDRAM uses a

pipelined architecture and therefore does not require the 2n rule

associated with a prefetch architecture. A WRITE command can

be initiated on any clock cycle following a previous WRITE

command. Full-speed random write accesses within a page can

be performed to the same bank, as shown in Figure 16, or each

subsequent WRITE may be performed to a different bank.

T0 T1 T2 T3

NOP

CLK

COMMAND

ADDRESS

BANK,

COL n

NOP NOP

DIN nDIN n+1

NOTE: Burst length = 2. DQM is LOW.

NOTE: DQM is LOW. Each WRITE command may be to any bank.

Figure 14

WRITE BURST

Figure 15

WRITE TO WRITE

DON’T CARE

T0 T1 T2

WRITE NOP

CLK

COMMAND

ADDRESS

BANK,

COL n

WRITE

DIN nDIN n+1 DIN b

BANK,

COL b

Figure 13

WRITE COMMAND

CLK

CKE

CS\

RAS\

CAS\

WE\

A0-A7: x16

BA0,1

COLUMN ADDRESS

BANK ADDRESS

ENABLE AUTO PRECHARGE

DISABLE AUTO PRECHARGE

A8, A9, A11: x16

A10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

Data for any WRITE burst may be truncated with a sub-

sequent READ command, and data for a ﬁ xed-length WRITE burst

may be immediately followed by a subsequent READ command.

Once the READ command is registered, the data inputs will be

ignored, and WRITEs will not be executed. An example is shown

in Figure 17. Data n+1 is either the last of a burst of two or the

last desired of a longer burst.

Data for a ﬁ xed-length WRITE burst may be followed

by , or truncated with, a PRECHARGE command to the same bank

(provided that AUTO PRECHARGE was not activated), and a

full-page WRITE burst may be truncated with a PRECHARGE

command to the same bank. The PRECHARGE command should

be issued tWR after the clock edge at which the last desired input

data element is registered. The Auto Precharge mode requires a

tWR of at least one clock plus time (8ns), regardless of frequency.

In addition, when truncating a WRITE burst, the DQM signal

must be used to mask input data for the clock edge prior to, and

the clock edge coincident with, the PRECHARGE command. An

example is shown in Figure 18. Data n + 1 is either the last of a

burst of two or the last desired of a longer burst. Following the

PRECHARGE command, a subsequent command to the same

bank cannot be issued until tRP is met.

In the case of a ﬁ xed-length burst being executed to

completion, a PRECHARGE command issued at the optimum time

(as described above) provides the same operation that would result

from the same ﬁ xed-length burst with AUTO PRECHARGE. The

disadvantage of the PRECHARGE command is that it requires that

the command and address buses be available at the appropriate

time to issue the command; the advantage of the PRECHARGE

command is that it can be used to truncate ﬁ xed-length or full-page

bursts.

NOTE: DQM coulc remain LOW in this example if the WRITE burst is a ﬁ xed length

of 2.

DON’T CARE

Figure 18

WRITE TO PRECHARGE

tRP

DQM

COMMAND WRITE NOP PRE-

NOP NOP NOP

ADDRESS BANK a,

COL n

BANK

(a or all)

DQ DIN nDIN n+1

ACTIVE

BANK a,

ROW

tWR

tWR= 2 CLK (“A2 version”)

T0 T1 T2 T3 T4 T5

CLK

T0 T1 T2 T3

CLK

COMMAND

ADDRESS

BANK,

COL n

DIN nDIN a

NOTE: Each WRITE command may be to any bank. DQM is LOW.

Figure 16

RANDOM WRITE CYCLES

BANK,

COL aBANK,

COL x

BANK,

COL m

DIN xDIN m

CLK

COMMAND

ADDRESS

NOP NOP NOP

BANK,

COL n

READ NOP

T0 T1 T2 T3 T4 T5

DIN n

BANK,

COL b

DIN n+1 DOUT bDOUT b+1

NOTE: The WRITE command may be to any bank, and the READ command may be to

any bank. DQM is LOW. CAS latency = 2 for illustration.

Figure 17

WRITE TO READ

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

Fixed-length or full-page WRITE bursts can be truncated

with the BURST TERMINATE command. When truncating a

WRITE burst, the input data applied coincident with the BURST

TERMINATE command will be ignored. The last data written

(provided that DQM is LOW at that time) will be the input data

applied one clock previous to the BURST TERMINATE command.

This is shown in Figure 19, where data n is the last desired data

element of a longer burst.

PRECHARGE

The PRECHARGE command is used to deactivate the

open row in a particular bank or the open row in all banks. The

bank(s) will be available for a subsequent row access some speci-

ﬁ ed time (tRP) after the PRECHARGE command is issued. Input

A10 determines whether one or all banks are to be precharged,

and in the case where only one bank is to be precharged, inputs

BA0, BA1 select the bank. When all banks are to be prechar ged,

inputs BA0, BA1 are treated as “Don’t Care.” Once a bank has

been precharged, it is in the idle state and must be activated prior

to any READ or WRITE commands being issued to that bank.

POWER-DOWN

Power-down occurs if CKE is registered LOW coincident

with a NOP or COMMAND INHIBIT when no accesses are in

progress. If power-down occurs when all banks are idle, this mode

is referred to as precharge power-down; if power-down occurs

when there is a row active in either bank, this mode is referred to

as active power-down. Entering power -down deactivates the input

and output buffers, excluding CKE, for maximum power savings

while in standby. The device may not remain in the power-down

state longer than the refresh period (64ms/16ms) since no refresh

operations are performed in this mode.

The power-down state is exited by registering a NOP or

COMMAND INHIBIT and CKE HIGH at the desired clock edge

(meeting tCKS).

T0 T1 T2

WRITE

CLK

COMMAND

ADDRESS

BANK,

COL n

NEXT COM-

MAND

DIN n

NOTE: DQMs is LOW.

Figure 19

TERMINATING A WRITE BURST

BURST

TERMINATE

(ADDRESS)

CLK

CKE

COMMAND

tCKS >tCKS

NOP NOP ACTIVE

tRCD

tRC

tRAS

Input buffers gated off

All banks idle

Enter power-down mode. Exit power-down mode.

DON’T CARE

Figure 21

POWER-DOWN

CLK

CKE

CS\

RAS\

CAS\

WE\

A0-A9

BA BANK ADDRESS

Figure 20

PRECHARGE COMMAND

A10

BANK SELECTED

ALL BANKS

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

CLOCK SUSPEND

The clock suspend mode occurs when a column access/

burst is in progress and CKE is registered LOW. In the clock

suspend mode, the internal clock is deactivated, “freezing” the

synchronous logic.

For each positive clock edge on which CKE is sampled

LOW , the next internal positive clock edge is suspended. Any com-

mand or data present on the input pins at the time of a suspended

internal clock edge is ignored; any data present on the DQ pins

remains driven; and burst counters are not incremented, as long

as the clock is suspended. (See examples in Figures 22 and 23.)

Clock suspend mode is exited by registering CKE HIGH;

the internal clock and related operation will resume on the subse-

quent positive clock edge.

BURST READ/SINGLE WRITE

The burst read/single write mode is entered by pro-

gramming the write burst mode bit (M9) in the Mode Register

to a logic 1. In this mode, all WRITE commands result in the

access of a single column location (burst of one), regardless of

the programmed burst length. READ commands access columns

according to the programmed burst length and sequence, just as

in the normal mode of operation (M9=0).

NOTE: For this example, CAS latency = 2, burst length = 4 or greater, and DQM is LOW.

Figure 23

CLOCK SUSPEND DURING READ BURST

DON’T CARE

CLK

COMMAND

ADDRESS

CKE

INTERNAL

CLOCK

T0 T1 T2 T3 T4 T5 T6

NOPREAD NOP NOP NOP

NOP

BANK,

COL n

DOUT nDOUT n+2 DOUT n+3

DOUT n+1

CLK

COMMAND

ADDRESS

WRITENOP NOP NOP

BANK,

COL n

T0 T1 T2 T3 T4 T5

DIN

n+1

DIN

n+2

NOTE: For this example, burst length = 4 or greater, and DQM is LOW.

Figure 22

CLOCK SUSPEND DURING WRITE

BURST

CKE

INTERNAL

CLOCK

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

CONCURRENT AUTO PRECHARGE

An access command (READ or WRITE) to another bank

while an access command with AUTO PRECHARGE enabled is

executing is not allowed by SDRAMs, unless the SDRAM sup-

ports CONCURRENT AUTO PRECHARGE. Micross SDRAMs

support CONCURRENT AUTO PRECHARGE. Four cases where

CONCURRENT AUTO PRECHARGE occurs are deﬁ ned be-

low.

READ with AUTO PRECHARGE

1. Interrupted by a READ (with or without AUTO PRE

CHARGE): A READ to bank m will interrupt a READ

on bank n, CAS latency later. The PRECHARGE to bank n

will begin when the READ to bank m is registered

(Figure 24).

2. Interrupted by a WRITE (with or without AUTO

PRECHARGE): A WRITE to bank m will interrupt a

READ on bank n when registered. DQM should be used

two clocks prir to the WRITE command to prevent bus

contention. The PRECHARGE to bank n will begin when

the WRITE to bank m is registered (Figure 25).

Figure 24

READ WITH AUTO PRECHARGE INTERRUPTED BY A READ

NOTE: DQM is LOW.

DOUT aDOUT a+1 DOUT dDOUT d+1

ADDRESS

BANK n,

COL a

BANK m,

COL d

tRP - BANK n

CAS Latency = 3 (BANK n)

T0 T1 T2 T3 T4 T5

NOP NOP

READ-AP

BANK n NOP NOP

CLK

COMMAND

NOP

READ-AP

BANK m

CAS Latency = 3 (BANK m)

Page Active READ with burst of 4 Interrupt Burst, Precharge

Pre-

READ with burst of 4

Page Active

Internal

States

BANK n

BANK m

tRP-BANK m

Figure 25

READ WITH AUTO PRECHARGE INTERRUPTED BY A WRITE

NOTE: 1. DQM is HIGH at T2 to prevent DOUT

-a+1 from contending with DIN-d at T4.

DOUT aDIN d

CAS Latency = 3 (BANK n)

ADDRESS BANK n,

COL a

BANK m,

COL d

tRP - BANK n

T0 T1 T2 T3 T4 T5

NOP NOP

READ-AP

BANK n NOP NOP

CLK

COMMAND

NOP

WRITE-AP

BANK m

Page Ac-

tive READ with burst of 4 Interrupt Burst, Precharge

Write back

WRITE with burst of 4

Page Active

Internal

States

BANK n

BANK m

DQM1

DIN

d+1

DIN

d+2

DIN

d+3

Don’t Care

tWR-BANKm

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

WRITE with AUTO PRECHARGE

3. Interrupted by a READ (with or without AUTO

PRECHARGE): A READ to bank m will interrupt a

WRITE on bank n when registered, with the data-out

appearing CAS latency later. The PRECHARGE to bank

will begin after tWR is met, where tWR begins when the

READ to bank m is registered. The last valid WRITE to

bank n will be data-in registered one clock prior to the

READ to bank m (Figure 26).

4 Interrupted by a WRITE (with or without AUTO

PRECHARGE): A WRITE to bank m will interrupt a

WRITE on bank n when registered. The PRECHARGE to

bank n will begin after tWR is met, where tWR begins when

the WRITE to bank m is registered. The last valid data

WRITE to bank n will be data registered one clock prior

to a WRITE to bank 1 (Figure 27).

Figure 26

WRITE WITH AUTO PRECHARGE INTERRUPTED BY A READ

NOTE: DQM is LOW.

DIN aDIN

a+1 DOUT dDOUT d+1

ADDRESS

BANK n,

COL a

BANK m,

COL d

tWR - BANK n

T0 T1 T2 T3 T4 T5

NOP NOP

WRITE-AP

BANK n NOP NOP

CLK

COMMAND

NOP

WRITE-AP

BANK m

CAS Latency = 3 (BANK m)

Page Active WRITE with burst of 4 Interrupt Burst, Write back Precharge

READ with burst of 4

Page Active

Internal

States

BANK n

BANK m

tRP-BANK ntRP-BANK m

Figure 27

WRITE WITH AUTO PRECHARGE INTERRUPTED BY A WRITE

NOTE: DQM is LOW.

DIN aDIN

a+1

ADDRESS

BANK n,

COL a

BANK m,

COL d

tWR - BANK n

T0 T1 T2 T3 T4 T5

NOP NOP

WRITE-AP

BANK n NOP NOP

CLK

COMMAND

NOP

WRITE-AP

BANK m

Page Active WRITE with burst of 4 Interrupt Burst, Write back Precharge

WRITE with burst of 4

Page Active

Internal

States

BANK n

BANK m

tRP-BANK ntWR-BANK m

Write back

DIN

a+2

DIN

d+1

DIN

d+2

DIN

d+3

Don’t Care

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

CKE

n-1

CKE

CURRENT STATE COMMAND

ACTION

NOTES

Power-Down X Maintain Power-Down

Self Refresh X Maintain Self Refresh

Clock Suspend X Maintain Clock Suspend

Power-Down COMMAND INHIBIT or NOP Exit Power-Down 5

Self Refresh COMMAND INHIBIT or NOP Exit Self Refresh 6

Clock Suspend X Exit Clock Suspend 7

All Banks Idle COMMAND INHIBIT or NOP Power-Down Entry

All Banks Idle AUTO REFRESH Self Refresh Entry

Reading or Writing VALID Clock Suspend Entry

HH See Truth Table 3

NOTE:

1. CKE n is the logic state of CKE at clock edge n; CKE n-1 was the state of CKE at the previous clock edge.

2. Current state is the state of the SDRAM immediately prior to clock edge n.

3. COMMAND n is the command registered at clock edge n, and ACTION n is a result of COMMAND n .

4. All states and sequences not shown are illegal or reserved.

5. Exiting power-down at clock edge n will put the device in the all banks idle state in time for clock edge n + 1

(provided that tCKS is met).

6. Exiting self refresh at clock edge n will put the device in the all banks idle state once tXSR is met. COMMAND

INHIBIT or NOP commands should be issued on any clock edges occurring during the tXSR period. A

minimum of two NOP commands must be provided during tXSR period.

7. After exiting clock suspend at clock edge n, the device will resume operation and recognize the next

command at clock edge n + 1.

TRUTH TABLE 2-CKE1,2,3,4

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

CURRENT STATE CS\ RAS\ CAS\ WE\ COMMAND (ACTION) NOTES

H X X X COMMAND INHIBIT (NOP/Continue previous operation)

L H H H NO OPERATION (NOP/Continue previous operation)

L L H H ACTIVE (Select and activate row)

L L L H AUTO REFRESH 7

L L L L LOAD MODE REGISTER 7

L L H L PRECHARGE 11

L H L H READ (Select column and start READ burst) 10

L H L L WRITE (Select column and start WRITE burst) 10

L L H L PRECHARGE (Deactivate row in bank or banks) 8

L H L H READ (Select column and start new READ burst) 10

L H L L WRITE (Select column and start WRITE burst) 10

L L H L PRECHARGE (Truncate READ burst, start PRECHARGE) 8

L H H L BURST TERMINATE 9

L H L H READ (Select column and start READ burst) 10

L H L L WRITE (Select column and start new WRITE burst) 10

L L H L PRECHARGE (Truncate WRITE burst, start PRECHARGE) 8

L H H L BURST TERMINATE 9

Write ( Auto-

Precharge

Disabled)

ANY

Idle

Row Active

Read ( Auto-

Precharge

Disabled)

NOTE:

1. This table applies when CKE n-1 was HIGH and CKE n is HIGH (see Truth Table 2) and after tXSR has been met (if the previous state was

self refresh).

2. This table is bank-speciﬁ c, except where noted; i.e., the current state is for a speciﬁ c bank and the commands shown are those allowed to be

issued to that bank when in that state. Exceptions are covered in the notes below.

3. Current state deﬁ nitions:

Idle: The bank has been precharged, and tRP has been met.

Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/accesses and no register accesses are in

progress.

Read: A READ burst has been initiated, with AUTO PRECHARGE disabled, and has not yet terminated or been terminated.

Write: A WRITE burst has been initiated, with AUTO PRECHARGE disabled, and has not yet terminated or been terminated.

4. The following states must not be interrupted by a command issued to the same bank. COMMAND INHIBIT or NOP commands, or allow-

able commands to the other bank should be issued on any clock edge occurring during these states. Allowable commands to the other bank

are determined by its current state and Truth Table 3, and according to Truth Table 4.

Precharging: Starts with registration of a PRECHARGE command and ends when tRP is met. Once tRP is met, the bank

will be in the idle state.

Row Activating: Starts with registration of an ACTIVE command and ends when tRCD is met. Once tRCD is met, the bank

will be in the row active state.

Read w/Auto-

Precharge Enabled: Starts with registration of a READ command with AUTO PRECHARGE enabled and ends when tRP has

been met. Once tRP is met, the bank will be in the idle state.

Write w/Auto-

Precharge Enabled: Starts with registration of a WRITE command with AUTO PRECHARGE enabled and ends when tRP has

been met. Once tRP is met, the bank will be in the idle state.

TRUTH TABLE 3 - CURRENT STATE BANK n - COMMAND TO BANK n

(Notes 1 to 6; notes appear below and on next page)

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

NOTE (continued):

5. The following states must not be interrupted by any executable command; COMMAND INHIBIT or NOP commands must be applied

on each positive clock edge during these states.

Refreshing: Starts with registration of an AUTO REFRESH command and ends when tRC is met.

Once tRC is met, the SDRAM will be in the all banks idle state.

Accessing Mode

has been met. Once tMRD is met, the SDRAM will be in the all banks idle state.

Precharging All: Starts with registration of a PRECHARGE ALL command and ends when tRP is met.

Once tRP is met, all banks will be in the idle state.

6. All states and sequences not shown are illegal or reserved.

7. Not bank-speciﬁ c; requires that all banks are idle.

8. May or may not be bank-speciﬁ c; if all banks are to be precharged, all must be in a valid state for precharging.

9. Not bank-speciﬁ c; BURST TERMINATE affects the most recent READ or WRITE burst, regardless of bank..

10. READs or WRITEs listed in the Command (Action) column include READs or WRITEs with AUTO PRECHARGE enabled and

READs or WRITEs with AUTO PRECHARGE disabled.

11. Does not affect the state of the bank and acts as a NOP to that bank.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

CURRENT STATE CS\ RAS\ CAS\ WE\ NOTES

HXXX

LHHH

Idle X X X X

LLHH

LHLH 7

LHLL 7

LLHL

LLHH

L H L H 7, 10

L H L L 7, 11

LLHL 9

LLHH

LHLH 7, 1

LHLL 7, 13

LLHL 9

LLHH

LH L H 7, 8 ,14

L H L L 7, 8 15

LLHL 9

LLHH

L H L H 7, 8 16

L H L L 7, 8 17

LLHL 9

Row Activating,

Active or

Precharging

Any command otherwise allowed to bank m

ACTIVE (select and activate row)

READ (select column and start READ burst)

Write

(Auto-

Precharge Disabled)

COMMAND/ACTION

COMMAND INHIBIT (NOP/continue previous operation)

NO OPERATION (NOP/continue previous operation)

WRITE (select column and start WRITE burst)

PRECHARGE

READ (select column and start READ burst)

Any

Read

(Auto-

Precharge Disabled)

ACTIVE (select and activate row)

READ (select column and start new READ burst)

WRITE (select column and start WRITE burst)

PRECHARGE

Read

(with Auto-

Precharge)

Write

(with Auto-

Precharge)

WRITE (select column and start new WRITE burst)

PRECHARGE

ACTIVE (select and activate row)

READ (select column and start READ burst)

WRITE (select column and start new WRITE burst)

PRECHARGE

ACTIVE (select and activate row)

READ (select column and start new READ burst)

WRITE (select column and start WRITE burst)

NOTE:

1. This table applies when CKE n-1 was HIGH and CKE n is HIGH (see Truth Table 2) and after tXSR has been met (if the previous state was

self refresh).

2. This table describes alternate bank operation, except where noted; i.e., the current state is for bank n and the commands shown are those

allowed to be issued to bank m (assuming that bank m is in such a state that the given command is allowable). Exceptions are covered in

the notes below.

3. Current state deﬁ nitions:

Idle: The bank has been precharged, and tRP has been met.

Row Active: A row in the bank has been activated, and tRCD has been met. No data bursts/ accesses and no register accesses

are in progress.

Read: A READ burst has been initiated, with AUTO PRECHARGE disabled, and has not yet terminated or been termi-

nated.

Write: A WRITE burst has been initiated, with AUTO PRECHARGE disabled, and has not yet terminated or been

terminated.

Read w/Auto-

Precharge Enabled: Starts with registration of a READ command with AUTO PRECHARGE enabled, and ends when tRP has been

met. Once tRP is met, the bank will be in the idle state.

Write w/Auto-

Precharge Enabled: Starts with registration of a WRITE command with AUTO PRECHARGE enabled, and ends when tRP has been

met. Once tRP is met, the bank will be in the idle state.

4. AUTO REFRESH, SELF REFRESH and LOAD MODE REGISTER commands may only be issued when all banks are idle.

5. A BURST TERMINATE command cannot be issued to another bank; it applies to the bank represented by the current state only.

6. All states and sequences not shown are illegal or reserved.

7. READs or WRITEs to bank m listed in the Command (Action) column include READs or WRITEs with AUTO PRECHARGE enabled

and READs or WRITEs with AUTO PRECHARGE disabled.

TRUTH TABLE 4 - CURRENT STATE BANK n - COMMAND TO BANK m

(Notes: 1-6; notes appear below and on next page)

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

NOTE (continued):

8. CONCURRENT AUTO PRECHARGE: Bank n will initiate the AUTO PRECHARGE command when its burst has been interrupted

by bank m’s burst.

9. Burst in bank n continues as initiated.

10. For a READ without AUTO PRECHARGE interrupted by a READ (with or without AUTO PRECHARGE), the READ to bank m

will interrupt the READ on bank n, CAS latency later (Figure 7).

11. For a READ without AUTO PRECHARGE interrupted by a WRITE (with or without AUTO PRECHARGE), the WRITE to bank m

will interrupt the READ on bank n when registered (Figures 9 and 10). DQM should be used one clock prior to the WRITE command

to prevent bus contention.

12. For a WRITE without AUTO PRECHARGE interrupted by a READ (with or without AUTO PRECHARGE), the READ to bank m

will interrupt the WRITE on bank n when registered (Figure 17), with the data-out appearing CAS latency later. The last valid WRITE

to bank n will be data-in registered one clock prior to the READ to bank m.

13. For a WRITE without AUTO PRECHARGE interrupted by a WRITE (with or without AUTO PRECHARGE), the WRITE to bank m

will interrupt the WRITE on bank n when registered (Figure 15). The last valid WRITE to bank n will be data-in registered one clock

prior to the READ to bank m.

14. For a READ with AUTO PRECHARGE interrupted by a READ (with or without AUTO PRECHARGE), the READ to bank m will

interrupt the READ on bank n, CAS latency later. The PRECHARGE to bank n will begin when the READ to bank m is registered

(Figure 24).

15. For a READ with AUTO PRECHARGE interrupted by a WRITE (with or without AUTO PRECHARGE), the WRITE to bank m will

interrupt the READ on bank n when registered. DQM should be used two clocks prior to the WRITE command to prevent bus conten-

tion. The PRECHARGE to bank n will begin when the WRITE to bank m is registered (Figure 25).

16. For a WRITE with AUTO PRECHARGE interrupted by a READ (with or without AUTO PRECHARGE), the READ to bank m will

interrupt the WRITE on bank n when registered, with the data-out appearing CAS latency later. The PRECHARGE to bank n will

begin after tWR is met, where tWR begins when the READ to bank m is registered. The last valid WRITE to bank n will be data-in

registered one clock prior to the READ to bank m (Figure 26).

17. For a WRITE with AUTO PRECHARGE interrupted by a WRITE (with or without AUTO PRECHARGE), the WRITE to bank m

will interrupt the WRITE on bank n when registered. The PRECHARGE to bank n will begin after tWR is met, where tWR begins when

the WRITE to bank m is registered. The last valid WRITE to bank n will be data registered one clock prior to the WRITE to bank m

(Figure 27).

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

ABSOLUTE MAXIMUM RATINGS*

Voltage on VDD/VDDQ Supply

Relative to VSS ............................................ -0.5V to +4.6V

Voltage on Inputs, NC or I/O Pins

Relative to VSS ............................................ -0.5V to +4.6V

Operating Temperature, TA (IT).....................-40°C to +85°C

Operating Temperature, TA (ET)..................-40°C to +105°C

Operating Temperature, TA (XT)...................-55°C to +125°C

Storage Temperature (plastic) ..................-55°C to +150°C

Power Dissipation ........................................................ 1W

*Stresses greater than those listed as “Absolute Maximum

Ratings” may cause permanent damage to the device. This

is a stress rating only, and functional operation of the device

at these or any other conditions above those indicated in the

operational sections of this speciﬁ cation is not implied. Ex-

posure to absolute maximum rating conditions for extended

periods may affect reliability.

PARAMETER/CONDITION SYMBOL MIN MAX UNITS NOTES

Supply Voltage VDD/VDDQ33.6V

Input High (Logic 1) Voltage, all inputs VIH 2.2 VDD +0.3 V23

Input Low (Logic 0) Voltage, all inputs VIL -0.5 0.7 V 23

INPUT LEAKAGE CURRENT

Any input 0V<VIN<VDD

(All other pins not under test = 0V)

II-5 5 μΑ

OUTPUT LEAKAGE CURRENT (DQs are disabled; 0V<VOUT<VDDQ) IOZ -5 5 μΑ

VOH 2.4 -- V

VOL -- 0.4 V

OUTPUT LEVELS

Output High Voltage (IOUT = -4mA)

Output Low Voltage (IOUT = 4mA)

DC ELECTRICAL CHARACTERISTICS AND OPERATING CONDITIONS

(Notes: 1, 6) (VDD/VDDQ =+3.3 V +0.3V)

IDD SPECIFICATIONS AND CONDITIONS1, 6, 11, 13 (sVDD/VDDQ =+3.3 V +0.3V)

SYM -8-10 UNITS NOTES

DD1

120 110 mA 3, 18,

DD2

2.5 2.5 mA

DD3

45 40 mA 3, 12,

DD4

145 120 mA 3, 18,

RFC

= t

RFC

(MIN); CL = 3 I

DD5

205 195mA

RFC

= 15.625μs; CL = 3 I

DD6

50 45 mA

DD7

2.5 2.5 mA 4

MAX

OPERATING CURRENT; Active Mode, Burst = 2,

READ or WRITE, t

(MIN), CAS latency = 3,

= 10ns (15ns for -10)

SELF REFRESH CURRENT: CKE<0.2V (-40 to +85 only)

AUTO REFRESH CURRENT;

CKE=HIGH; CS\=HIGH

=10ns (15ns for -10)

PARAMETER/CONDITIONS

3, 12,

18, 19

STANDBY CURRENT: Power-Down Mode;

All banks idle; CKE=LOW; t

= 10ns (15ns for -10)

STANDBY CURRENT; Active Mode; CKE=HIGH,

CS\=HIGH; t

= 10ns (15ns for -10),

All banks active after t

RCD

met; No accesses in progress

OPERATING CURRENT: Burst Mode; Continuous burst;

READ or WRITE; t

= 10ns (15ns for -10);

All banks active; CAS latency = 3

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

SYMBOL MAX UNITS NOTES

4.0 pF 2

5.0 pF 2

6.5 pF 2

PARAMETER

Input Capacitance: CLK

Input Capacitance: All other input-only pins

Input/Output Capacitance: DQs

MIN MAX MIN MAX

CL = 3 t

6.5 7 ns

CL = 2 t

99ns22

Address hold time t

11ns

Address setup time t

23ns

CLK high-level width t

33.5ns

CLK low-level width t

33.5ns

CL = 3 t

810ns24

CL = 2 t

12 15 ns 22, 24

CKE hold time t

CKH

11ns

CKE setup time t

CKS

23ns

CS#, RAS#, CAS#, WE#, DQM hold time t

CMH

11ns

CS#, RAS#, CAS#, WE#, DQM setup time t

CMS

23ns

Data-in hold time t

11ns

Data-in setup time t

23ns

CL = 3 t

68ns10

CL = 2 t

710ns10

Data-out low-impedance time t

11ns

Data-out hold time t

2.5 2.5 ns

ACTIVE to PRECHARGE command t

RAS

50 80,000 60 80,000 ns

AUTO REFRESH, ACTIVE command period t

80 90 ns 22

ACTIVE to READ or WRITE delay t

RCD

20 30 ns 22

Refresh period (4,096 rows)

-40 to +85 degrees C

REF

64 64 ms

Refresh period (4,096 rows)

-55 to +125 degrees C

REF

16 16 ms

PRECHARGE command period t

24 30 ns 22

ACTIVE bank A to ACTIVE bank B command t

RRD

20 20 ns

Transition time t

0.3 1.2 1 1.2 ns 7

1 CLK + 1 CLK + - 25

8ns 8ns

15 15 ns 26

Exit SELF REFRESH to ACTIVE command t

XSR

80 90 ns 20

Clock cycle time

Data-out high-impedance time

WRITE recovery time A2 version

NOTESPARAMETER SYM

Access time from CLK (pos. edge)

-8 -10 UNITS

CAPACITANCE

ELECTRICAL CHARACTERISTICS AND RECOMMENDED AC OPERATING CONDITIONS

(Notes: 5, 6, 8, 9, 11)

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

SYMBOL -8 -10 UNITS NOTES

CCD

CKED

PED

DQD

DQM

DQZ

DWD

Data-in to ACTIVE command A2 version t

DAL

15, 21

Data-in to PRECHARGE command A1 version A2 version t

DPL

16, 21

BDL

CDL

Last data-in to PRECHARGE command A2 version t

RDL

16, 21

MRD

CL = 3 t

ROH

CL = 2 t

ROH

Data-out to high-impedance from PRECHARGE command

Last data-in to burst STOP command

Last data-in to new READ/WRITE command

LOAD MODE REGISTER command to ACTIVE or REFRESH command

CKE to clock enable or power-down exit setup mode

CKE to clock disable or power-down entry mode

READ/WRITE command to READ/WRITE command

PARAMETER

WRITE command to input data delay

DQM to data high-impedance during READs

DQM to data mask during WRITEs

DQM to input data delay

MIN MAX

CL = 3 t

--- 6 ns 22

CL = 2 t

--- 9 ns 22

CL = 3 t

8 --- ns 22

CL = 2 t

12 --- ns 22

RCD

20 --- ns 22

24 --- ns 22

RCD

80 --- t

WRITE recovery time A2 Version t

2 --- --- ---

CLKs ---

PARAMETER

3-2-3

-8

SYM UNITS NOTES

PRECHARGE command period

AUTO REFRESH, ACTIVE command period

100 MHz Speed Reference (CL -t

RCD

-t

)

Clock cycle time

Access times from CLK (pos. edge)

ACTIVE to READ or WRITE delay

AC FUNCTIONAL CHARACTERISTICS5, 6, 7, 8, 9, 11

ELECTRICAL TIMING CHARACTERISTICS for -8 SPEED5, 6, 7, 8, 9, 11, 24

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

NOTES

1. All voltages referenced to VSS.

2. This parameter is sampled. VDD, VDDQ = +3.3V; f = 1

MHz, TA = 25°C; pin under test biased at 1.4V.

3. IDD is dependent on output loading and cycle rates.

Speciﬁ ed values are obtained with minimum cycle time

and the outputs open.

4. Enables on-chip refresh and address counters.

5. The minimum speciﬁ cations are used only to indicate

cycle time at which proper operation over the full tem-

perature range (-55°C ≤ TA ≤ +125°C) is ensured.

6. An initial pause of 100μs is required after power-up,

followed by two AUTO REFRESH commands, before

proper device operation is ensured. (VDD and VDDQ

must be powered up simultaneously. VSS and VSSQ

must be at same potential.) The two AUTO REFRESH

command wake-ups should be repeated any time the tREF

refresh requirement is exceeded.

7. AC characteristics assume tT = 1ns.

8. In addition to meeting the transition rate speciﬁ cation,

the clock and CKE must transit between VIH and VIL (or

between VIL and VIH) in a monotonic manner.

9. Outputs measured at 1.5V with equivalent load:

10. tHZ deﬁ nes the time at which the output achieves the

open circuit condition; it is not a reference to VOH or

VOL. The last valid data element will meet tOH before

going High-Z.

11. AC timing and ICC tests have VIL = 0V and VIH = 3V,

with timing referenced to 1.5V crossover point.

12. Other input signals are allowed to transition no more

than once in any 30ns period (20ns on -8) and are other-

wise at valid VIH or VIL levels.

13. IDD speciﬁ cations are tested after the device is properly

initialized.

14. Timing actually speciﬁ ed by tCKS; clock(s) speciﬁ ed as a

reference only at minimum cycle rate.

15. Timing actually speciﬁ ed by tWR plus tRP; clock(s) speci-

ﬁ ed as a reference only at minimum cycle rate.

16. Timing actually speciﬁ ed by tWR.

17. Required clocks are speciﬁ ed by JEDEC functionality

and are not dependent on any timing parameter.

18. The ICC current will decrease as the CAS latency is

reduced. This is due to the fact that the maximum cycle

rate is slower as the CAS latency is reduced.

19. Address transitions average one transition every 30ns

(20ns on -8).

20. CLK must be toggled a minimum of two times during

this period.

21. Based on tCK = 100 MHz for -8 and 66 MHz for -10.

22. These ﬁ ve parameters vary between speed grades and

deﬁ ne the differences between the -8 SDRAM speeds:

-8.

23. VIH overshoot: VIH (MAX) = VDDQ + 2V for a pulse

width ≤ 10ns, and the pulse width cannot be greater than

one third of the cycle rate. VIL undershoot: VIL (MIN) =

-2V for a pulse width ≤ 10ns, and the pulse width cannot

be greater than one third of the cycle rate.

24. The clock frequency must remain constant during access

or precharge states (READ, WRITE, including tWR, and

PRECHARGE commands). CKE may be used to reduce

the data rate.

25. Auto precharge mode only. The precharge timing budget

( tRP) begins 8ns after the ﬁ rst clock delay, after the last

WRITE is executed.

26. Precharge mode only.

27. JEDEC and PC100 specify three clocks.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheses.

NOTE: 1. The Mode Register may be loaded prior to the AUTO REFRESH cycles if desired.

2. If CS is HIGH at clock high time, all commands applied are NOP, with CKE a “Don’t Care”.

3. JEDEC and PC100 specify three clocks.

4. Outputs are guaranteed High-Z after command is issued.

MIN MAX MIN MAX

tAH 11ns

tAS 23ns

tCH 33.5ns

tCL 33.5ns

tCK (3) 810ns

tCK (2) 12 15 ns

tCKH 11ns

SYMBOL* UNITS

-8 -10

MIN MAX MIN MAX

tCKS 23ns

tCMH 11ns

tCMS 23ns

tMRD (3) 22

tCK

tRC 80 90 ns

tRP 24 30 ns

SYMBOL* UNITS

-8 -10

INITIALIZE AND LOAD MODE REGISTER2

tCK tCH

tCL

T0 T1 Tn+1 To+1 Tp+1 Tp+2 Tp+3

NOP

tCMHtCMS

PRE- NOP NOP

AUTO

REFRESH AUTO

REFRESH NOP NOP LOAD MODE

tCMHtCMS tCMHtCMS

CODE ROW

ALL BANKS

SINGLE BANK

tAS tAH

CODE

tAS tAH

ROW

ALL

BANKS BANK

High-Z

T=100s tRP tRC tMRD

Power-up:

VDD and

CLK stable

Precharge

all banks AUTO RE- AUTO RE-

tRC

Program Mode Register 1,3,4

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9, A1 1

A10

BA0, BA1

Don’t Care

Undeﬁ ned

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheses.

NOTE: 1. Violating refresh requirements during power-down

may result in a loss of data.

tCK tCL tCH

T0 T1 T2 Tn Tn

tCK tCK

PRECHARGE NOP NOP ACTIVE

ROW

ALL BANKS

SINGLE BANK

ROW

BANK

BANK(S)

NOP

tAS tAH

High-Z

All banks idle

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9, A1 1

A10

BA0, BA1

Don’t Care

Undeﬁ ned

POWER-DOWN MODE1

Two clock cycles Input bufferd gated off while in

power-down mode

Exit power-down mode

All banks idle, enter

power-down mode

Precharge all

active banks

MIN MAX MIN MAX

CK (2)

12 15 ns

CKH

11ns

CKS

23ns

CMH

11ns

CMS

23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

tAH 11ns

tAS 23ns

tCH 33.5ns

tCL 33.5ns

tCK (3) 810ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

tCK tCH

tCL

T0 T1 T2 T4 T6 T7 T8 T9T3 T5

READ NOP

CKS

NOP NOP NOP NOP WRITE NOP

COMMAND

COLUMN m2

tAS tAH

COLUMN e2

tAS tAH

BANK

tAS tAH

BANK

DOUT m DOUTm+1 DOUT a DOUT a-1

tDS tDH

tHZ

tAC

tOH

tAC

tLZ

CLK

CKE

DQM /

DQML,

DQMH

A0-A9,

A11

A10

CLOCK SUSPEND MODE1

Don’t Care

Undeﬁ ned

TIMING PARAMETERS

* CAS latency indicated in parentheses.

NOTE: 1. For this example, the burst length = 2, the CAS latency = 3, and AUTO PRECHARGE is disabled.

2. x16: A8, A9 and A11 = “Don’t Care.”

MIN MAX MIN MAX

AC(3)

6.5 7 ns

AC(2)

99ns

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

SYMBOL* UNITS

-8 -10

MIN MAX MIN MAX

CKS

23ns

CMH

11ns

CMS

23ns

11ns

23ns

HZ(3)

68ns

HZ(2)

710ns

11ns

2.5 2.5 ns

SYMBOL* UNITS

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

tCK tCL

tCH

T0 T1 T2 Tn To +1

PRECHARGE NOP ACTIVE

ROW

ALL BANKS

SINGLE BANK

ROW

BANK

BANK(S)

AUTO

REFRESH

tAS tAH

High-Z

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

A10

BA0, BA1

NOP NOP AUTO

REFRESH NOP NOP

tRP tRC tRC

Don’t Care

Undeﬁ ned

AUTO REFRESH MODE1

TIMING PARAMETERS

* CAS latency indicated in parentheses.

MIN MAX MIN MAX

tAH 11ns

tAS 23ns

tCH 33.5ns

tCL 33.5ns

tCK (3) 810ns

tCK (2) 12 15 ns

SYMBOL* UNITS

-10-8

MIN MAX MIN MAX

tCKH 11ns

tCKS 23ns

tCMH 11ns

tCMS 23ns

tRC 80 90 ns

tRP 24 30 ns

SYMBOL* UNITS

-10-8

NOTE: 1. Each AUTO REFRESH command performs a refresh cycle. Back-to-back commands are not required.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

tCK tCL

tCH

TTT TT

tCKS

PRECHARGE NOP NOP AUTO

REFRESH

ALL BANKS

SINGLE BANK

BANK(S)

AUTO

REFRESH

tAS tAH

High-Z

Exit self refresh mode

(Restart refresh time

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9, A1 1

A10

BA0, BA1

SELF REFRESH MODE1

tRAS

tXSR

CLK stable prior to exiting

self refresh mode

Enter self refresh mode

Precharge all

active banks Don’t Care

Undeﬁ ned

MIN MAX MIN MAX

tAH 11ns

tAS 23ns

tCH 34ns

tCL 34ns

tCK(3) 810ns

tCK(2) 12 15 ns

tCKH 11ns

SYMBOL* UNITS

-8 -10

MIN MAX MIN MAX

tCKS 23ns

tCMH 11ns

tCMS 23ns

tRAS 50 80,000 60 80,000 ns

tRP 24 30 ns

tXSR 80 90 ns

SYMBOL* UNITS

-8 -10

NOTE: 1. Self Refresh Mode available on Industrial Temperature Range option only.

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTE: 1. For this example, the burst length = 4, the CAS latency = 2, and the READ burst is followed by a “manual” PRECHARGE.

2. x16: A8, A9 and A11 = “Don’t Care.”

READ -- WITHOUT AUTO PRECHARGE1

CLK tCK tCH

tCL

CKE

tCKS tCKH

tCMS tCMH

COMMAND ACTIVE NOP READ NOP NOP NOP PRE- NOP

CMH

DQM /

DQML, DQMH

A0-A9,

A11 ROW

tCMS t

tAS t

ROW

tAS t

BA0, BA1 BANK

tAS t

BANK

DQ DOUT m

tAC

tLZ

tAC

ACTIVE

COLUMN m2

ROW ROW

ALL BANKS

SINGLE BANK

DISABLE AUTO PRECHARGE

BANK

DOUT m+1

tOH

DOUT m+2 DOUT m+3

tRP

tRC

tRAS

tRCD CAS Latency

A10

tAC

tOH

tAC

tOH tOH

tHZ

Don’t Care

Undeﬁ ned

T0 T1 T2 T3 T4 T5 T6 T7 T8

MIN MAX MIN MAX

AC(3)

6.5 7 ns

AC(2)

99ns

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

CKS

23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

CMH

11ns

CMS

23ns

HZ(3)

68ns

HZ(2)

710ns

11ns

2.5 2.5 ns

RAS

50 80,000 60 80,000 ns

80 90 ns

RCD

20 30 ns

24 30 ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

tCK tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP READ NOP NOP NOP NOP

CMH

ROW

tCMS t

tAS t

ROW

tAS t

BANK

tAS t

BANK

ACTIVE

COLUMN m2

ROW ROW

ENABLE AUTO PRECHARGE

BANK

READ -- WITH AUTO PRECHARGE1

T0 T1 T2 T3 T4 T5 T6 T7 T8

NOP

DOUT m

tAC

tLZ

DOUT m+1

tOH

DOUT m+2 DOUT m+3

tRP

tRC

tRAS

tRCD CAS Latency

tOH AC

tOH tOH

tHZ

CLK

CKE

COMMAND

DQM /

DQML, DQMH

A0-A9,

A11

BA0, BA1

A10

Don’t Care

Undeﬁ ned

TIMING PARAMETERS

NOTE: 1. For this example, the burst length = 4, the CAS latency = 2.

2. x16: A8, A9 and A11 = “Don’t Care.”

* CAS latency indicated in parentheseses.

MIN MAX MIN MAX

AC(3)

6.5 7 ns

AC(2)

99ns

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

CKS

23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

AC(3)

6.5 7 ns

AC(2)

99ns

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

CKS

23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

CMH

11ns

CMS

23ns

HZ(3)

68ns

HZ(2)

710ns

11ns

2.5 2.5 ns

RAS

50 80,000 60 80,000 ns

80 90 ns

RCD

20 30 ns

24 30 ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTE: 1. For this example, the burst length = 4, the CAS latency = 2.

2. x16: A8, A9 and A11 = “Don’t Care.”

ALTERNATING BANK READ ACCESSES1

tCK tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP READ NOP AC- NOP NOP

CMH

ROW

tCMS t

tAS t

ROW

tAS t

DOUT m

tAC

tLZ

tAC

COLUMN m2

ROW ROW

ENABLE AUTO PRECHARGE

DOUT m+1

ttOH

tAC tOH

tOH

DOUT m+2 DOUT m+3

tRP - BANK 0

tRRD

tRC - BANK 0

tRCD - BANK 0 CAS Latency - BANK 0

READ

tRAS - BANK 0

ROW COLUMN b2

ROW

ENABLE AUTO PRECHARGE

DOUT b

tAC tOH

tAC

T0 T1 T2 T3 T4 T5 T6 T7 T8

AC-

BANK 0 BANK 0 BANK 0

BANK 4

CAS Latency - BANK 1

RCD - BANK 1

tRCD - BANK 0

CLK

CKE

COMMAND

DQM /

DQML, DQMH

A0-A9,

A11

BA0, BA1

A10

Don’t Care

Undeﬁ ned

MIN MAX MIN MAX

tAC(3) 6.5 7 ns

tAC(2) 99ns

tAH 11ns

tAS 23ns

tCH 33.5ns

tCL 33.5ns

tCK(3) 810ns

tCK(2) 12 15 ns

tCKH 11ns

tCKS 23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

CMH

11ns

CMS

23ns

11ns

2.5 2.5 ns

RAS

50 80,000 60 80,000 ns

80 90 ns

RCD

20 30 ns

24 30 ns

RRD

20 20 ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTE: 1. For this example, the CAS latency = 2.

2. x16: A8, A9 and A11 = “Don’t Care.”

3. Page left open, no tRP.

MIN MAX MIN MAX

tAC(3) 6.5 7 ns

tAC(2) 99ns

tAH 11ns

tAS 23ns

tCH 33.5ns

tCL 33.5ns

tCK(3) 810ns

tCK(2) 12 15 ns

tCKH 11ns

tCKS 23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

CMH

11ns

CMS

23ns

HZ(3)

68ns

HZ(2)

710ns

11ns

2.5 2.5 ns

RCD

20 30 ns

UNITSSYMBOL*

-8 -10

READ -- FULL-PAGE BURST1

tCK

tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP READ NOP NOP NOP NOP

ROW

tCMS t

tAS t

BANK

tAS t

BANK

DOUT m

tAC

tLZ

tAC

COLUMN

ROW

DOUT m+1

ttOH

tAC tOH

tOH

DOUTm+2 DOUT m-1

tHZ

tRCD CAS Latency

NOP NOP NOP

DOUT m DOUT m+1

tOH

tAC tOH

tAC

256 (x16) locations within same row.

T0 T1 T2 T3 T4 T5 T6 Tn+1 Tn+2 Tn+3 Tn+4

Full page completed.

Full-page burst does not self-terminate. 3

Can use BURST TERMINATE command.

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

BA0, BA1

A10

Don’t Care

Undeﬁ ned

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTE: 1. For this example, the burst length = 4 , the CAS latency = 2.

2. x16: A8, A9 and A11 = “Don’t Care.”

MIN MAX MIN MAX

AC(3)

6.5 7 ns

AC(2)

99ns

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

CKS

23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

CMH

11ns

CMS

23ns

HZ(3)

68ns

HZ(2)

710ns

11ns

2.5 2.5 ns

RCD

20 30 ns

UNITSSYMBOL*

-8 -10

READ -- DQM OPERATION1

tCK tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP READ NOP NOP NOP NOP

CMH

ROW

tCMS t

tAS t

BANK

tAS t

BANK

DOUT m

tAC

tLZ

NOP

COLUMN m2

ROW

ENABLE AUTO PRECHARGE

ttOH

tAC tOH

tOH

DOUT m+2 DOUT m+3

tHZ

tRCD CAS Latency

NOP

tLZ

DISABLE AUTO PRECHARGE

T0 T1 T2 T3 T4 T5 T6 T7 T8

tHZ

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

BA0, BA1

A10

Don’t Care

Undeﬁ ned

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

WRITE -- WITHOUT AUTO PRECHARGE1

tCK tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP WRITE NOP NOP NOP PRECHARGE NOP

CMH

ROW

tCMS t

tAS t

ROW

tAS t

BANK

tAS t

BANK

DIN m+1

tDS

ACTIVE

COLUMN

ROW ROW

ALL BANKS

SINGLE BANK

DISABLE AUTO PRECHARGE

BANK

DIN m+2 DIN m+3

tWR tRP

tRC

tRAS

tRCD

DIN m

tDH tDS tDH tDS tDH tDS tDH

T0 T1 T2 T3 T4 T5 T6 T7 T8

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

BA0, BA1

A10

Don’t Care

Undeﬁ ned

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTE: 1. For this example, the burst length = 4, and the WRITE burst is followed by a “manual” PRECHARGE.

2. 15ns are required between <DINm+3> and the PRECHARGE command, regardless of frequency.

3. x16: A8, A9 and A11 = “Don’t Care.”

MIN MAX MIN MAX

CMH

11ns

CMS

23ns

11ns

23ns

RAS

50 80,000 60 80,000 ns

80 90 ns

RCD

20 30 ns

24 30 ns

15 15 ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

AC(3)

6.5 7 ns

AC(2)

99ns

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

CKS

23ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

WRITE -- WITH AUTO PRECHARGE1

T0 T1 T2 T3 T4 T5 T6 T7 T8

tCK tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP WRITE NOP NOP NOP NOP NOP

CMH

ROW

tCMS t

tAS t

ROW

tAS t

BANK

tAS t

BANK

DIN m+1

tDS

ACTIVE

COLUMN

ROW ROW

ENABLE AUTO PRECHARGE

BANK

DIN m+2 DIN m+3

tWR tRP

tRC

tRAS

tRCD

DIN m

tDH tDS tDH tDS tDH tDS tDH

NOP

Don’t Care

Undeﬁ ned

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

BA0, BA1

A10

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTE: 1. For this example, the burst length = 4, i.e., two-clock minimum for tWR.

2. x16: A8, A9 and A11 = “Don’t Care.”

MIN MAX MIN MAX

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

CKS

23ns

CMH

11ns

CMS

23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

11ns

23ns

RAS

50 80,000 60 80,000 ns

80 90 ns

RCD

20 30 ns

24 30 ns

1 CLK+

8ns

1 CLK+

8ns ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTES: 1. For this example, the burst length = 4, i.e., two-clock minimum for tWR.

2. Requires once clock plus time (8ns) with AUTO PRECHARGE or 15ns with PRECHARGE.

3. x16: A8, A9 and A11 = “Don’t Care.”

MIN MAX MIN MAX

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

CKS

23ns

CMH

11ns

CMS

23ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

tDH 11ns

tDS 22ns

tRAS 50 80,000 60 80,000 ns

tRC 80 90 ns

tRCD 20 30 ns

tRP 24 30 ns

tRRD 20 20 ns

tWR

1 CLK+

8ns

1 CLK+

8ns ns

UNITSSYMBOL*

-8 -10

ALTERNATING BANK WRITE ACCESSES1

tCK tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP WRITE NOP ACTIVE NOP NOP

CMH

ROW

tCMS t

tAS t

ROW

tAS t

ACTIVE

COLUMN

ROW ROW

ENABLE AUTO PRECHARGE

WRITE

ROW COLUMN b3

ROW

ENABLE AUTO PRECHARGE

BANK 0 BANK 0 BANK 0

BANK 1 BANK 1

DIN m+1

tDS

DIN m+2 DIN m+3

tWR - BANK 0 tRP - BANK 0

tRRD

tRC - BANK 0

tRCD - BANK 0

DIN m

tDH tDS tDH tDS tDH tDS tDH

DIN b

DS DH

DIN b+1

DS DH

DIN b+2

DS DH

tttttt

tRAS - BANK 0

NOP

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

BA0, BA1

A10

DIN b+3

DS DH

tRCD - BANK 1 tWR - BANK 1

tRCD - BANK 0

Don’t Care

Undeﬁ ned

T0 T1 T2 T3 T4 T5 T6 T7 T8 T9

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

WRITE -- FULL-PAGE BURST

tCK

tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP WRITE NOP NOP NOP

CMH

ROW

tCMS t

tAS t

BANK

tAS t

BANK

BURST

TERM

COLUMN

ROW

tRCD

NOP NOP

256 (x16) locations within same row.

Full page completed.

Full-page burst does not

self-terminate. Can use

BURST TERMINATE

command.2,3

DIN m+1

tDS

DIN m+2 DIN m+3

DIN m

tDH tDS tDH tDS tDH tDS tDH

DIN m-1

DS DH DS DH

tttt

T0 T1 T2 T3 T4 T5 Tn+1 Tn+2 Tn+3

Don’t Care

Undeﬁ ned

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

BA0, BA1

A10

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTES: 1. x16: A8, A9 and A11 = “Don’t Care.”

tWR must be satisﬁ ed prior to PRECHARGE command.

3. Page left open, no tRP.

MIN MAX MIN MAX

11ns

23ns

33.5ns

CK(3)

810ns

CK(2)

12 15 ns

CKH

11ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

CKS

23ns

CMH

11ns

CMS

23ns

11ns

23ns

RCD

20 30 ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

WRITE -- DQM OPERATION1

tCK tCH

tCL

tCKS tCKH

tCMS tCMH

ACTIVE NOP WRITE NOP NOP NOP NOP

CMH

ROW

tCMS t

tAS t

BANK

tAS t

BANK

COLUMN

ROW

ENABLE AUTO PRECHARGE

tRCD

NOP

DISABLE AUTO PRECHARGE

tDS

DIN m+2 DIN m+3

DIN m

tDH tDS tDH tDS tDH

CLK

CKE

COMMAND

DQM /

DQML,

DQMH

A0-A9,

A11

BA0, BA1

A10

Don’t Care

Undeﬁ ned

TIMING PARAMETERS

* CAS latency indicated in parentheseses.

NOTES: 1. For this example, the burst length = 4.

2. x16: A8, A9 and A11 = “Don’t Care.”

T0 T1 T2 T3 T4 T5 T6 T7

MIN MAX MIN MAX

tAH 11ns

tAS 23ns

tCH 33.5ns

tCL 33.5ns

tCK(3) 810ns

tCK(2) 12 15 ns

tCKH 11ns

UNITSSYMBOL*

-8 -10

MIN MAX MIN MAX

CKS

23ns

CMH

11ns

CMS

23ns

11ns

23ns

RCD

20 30 ns

UNITSSYMBOL*

-8 -10

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

NOTE: 1. All dimensions in inches (millimeters) or typical where noted.

2. Package width and length do not include mold protrusion; allowable mold protrusion is .01” per side.

MAX

MIN

MECHANICAL DEFINITIONS

Micross Case #901 (Package Designator DG)

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

MECHANICAL DEFINITIONS

Copper Lead Frame (Cu) (Package Designator DGC)

NOTE :

2. Dimension D and E1 do not include mold protrusion .

3. Dimension b does not include dambar protrusion/intrusion

1. Controlling dimension : mm

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

ORDERING INFORMATION

Device Number Package Type Speed Process

AS4SD4M16DG-8/IT 54-pin TSOPII, Alloy 42 Lead,

PbSn plating 125MHz Industrial

AS4SD4M16DG-8/ET 54-pin TSOPII, Alloy 42 Lead,

PbSn plating 125MHz Enhanced

AS4SD4M16DG-8/XT 54-pin TSOPII, Alloy 42 Lead,

PbSn plating 125MHz Military

AS4SD4M16DG-10/IT 54-pin TSOPII, Alloy 42 Lead,

PbSn plating 100MHz Industrial

AS4SD4M16DG-10/ET 54-pin TSOPII, Alloy 42 Lead,

PbSn plating 100MHz Enhanced

AS4SD4M16DG-10/XT 54-pin TSOPII, Alloy 42 Lead,

PbSn plating 100MHz Military

AS4SD4M16DGC-8/IT 54-pin TSOPII,Cu lead frame,

PbSn plating 125MHz Industrial

AS4SD4M16DGC-8/ET 54-pin TSOPII, Cu lead frame,

PbSn plating 125MHz Enhanced

AS4SD4M16DGC-8/XT 54-pin TSOPII, Cu lead frame,

PbSn plating 125MHz Military

AS4SD4M16DGC-10/IT 54-pin TSOPII, Cu lead frame,

PbSn plating 100MHz Industrial

AS4SD4M16DGC-10/ET 54-pin TSOPII,Cu lead frame,

PbSn plating

100MHz Enhanced

PbSn plating

AS4SD4M16DGC-10/XT 54-pin TSOPII,Cu lead frame,

PbSn plating 100MHz Military

AS4SD4M16DGCR-8/IT 54-pin TSOPII, Cu lead frame,

NiPdAu plating - RoHS 125MHz Industrial

AS4SD4M16DGCR-8/ET 54-pin TSOPII, Cu lead frame,

NiPdAu plating - RoHS 125MHz Enhanced

AS4SD4M16DGCR-8/XT 54-pin TSOPII, Cu lead frame,

NiPdAu plating - RoHS 125MHz Military

AS4SD4M16DGCR-10/IT 54-pin TSOPII, Cu lead frame,

NiPdAu plating - RoHS 100MHz Industrial

AS4SD4M16DGCR-10/ET 54-pin TSOPII, Cu lead frame,

NiPdAu plating - RoHS 100MHz Enhanced

AS4SD4M16DGCR-10/XT 54-pin TSOPII, Cu lead frame,

NiPdAu plating - RoHS 100MHz Military

*AVAILABLE PROCESSES

IT = Industrial Temperature Range -40oC to +85oC

ET= Enhanced Temperature Range -40°C to +105°C

XT = Military Temperature Range -55oC to +125oC

SDRAM

AS4SD4M16

Rev. 2.6 04/10

Micross Components reserves the right to change products or speciﬁ cations without notice.

DOCUMENT TITLE

4 Meg x 16 SDRAM Synchronous DRAM Memory

REVISION HISTORY

Rev # History Release Date Status

2.5 Added DGC Package & Copper Lead April 2010 Release

Frame information

2.6 Updated Features & Options - Page 1 April 2010 Release

Added Theta symbol on page 4 before jc

Changed all references of IT+ to ET

Updated Maximum Ratings - Page 30