PD-9001GR/AT/AC-US - MICROSEMI

-P

Notice

It is Microsemi’s policy to improve its products as new

technology, components, software, and firmware

become available. Microsemi, therefore, reserves the

right to change specifications without prior notice.

Technical Support

If you encounter problems when installing or using this

product, please consult the Microsemi website at:

http://www.Microsemi.com

For technical support, call: +972-9-775-5123

In the USA: 1-877-480-2323

Email: sales.support@microsemi.com

Recycling and Disposal

Disposal instructions for old products. The WEEE

(Waste Electrical and Electronic Equipment) national

environmental initiatives has been put in place to

ensure that products are recycled using best

available treatment, and recovery and recycling

techniques to ensure human health and high

environmental protection. Your product is designed

and manufactured with high quality materials and

components which can be recycled and reused. Do

not dispose of your old product in your general

household waste bin. Inform yourself about the local

separate collection system for electrical and

electronic products marked by this symbol:

Use one of the following disposal options :

1. Dispose of the complete product (including its

cables, plugs and accessories) in the designated

WEEE collection facility.

2. If you purchased a replacement product, return

your older product (including all components) back to

the retailer. The retailer should accept it as required

by the national WEEE legislation.

 Microsemi Corp.

Ordering information:

Part number: PD-9001GR/AC

 Product Family Name: Microsemi 9001GR

 Description: 1-Port 802.3at + Legacy Gigabit PoE Midspan

Part number: PD-9001GR/AT/AC

 Product Family Name: Microsemi 9001GR

 Description: 1-Port 802.3at Gigabit PoE Midspan

Document P/N : 06-0473-056, Rev. C00

Safety Information

Important Safety Information

 Connect the PD-9001GR to PoE networks only, without

routing to the outside plant.

 Only qualified personnel can install or remove the

PD-9001GR.

 AC Power Cord Set:

 The power cord must have regulatory agency approval for

the specific country in which it is used (for example UL,

CSA, VDE, etc.).

 The power cord must be a three-conductor type (two

current carrying conductors; one ground conductor)

terminated on one end by an IEC 60320 appliance coupler

(for connection to the PD-9001GR), and on the other end

by a plug containing a ground (earthing) contact.

 The power cord must be rated for a minimum of 250 VAC

RMS operation, with a minimum rated current capacity of

5 amps (or a minimum wire gauge of 18 AWG (0.75 mm2).

: A PD-9001GR installed in Australia requires power cords

with a minimum wire gauge of 16 AWG (1.0 mm2).

: The PD-9001GR "Data In" and "Data & Power Out" ports

are shielded RJ45 data sockets. They cannot be used as Plain

Old Telephone Service (POTS) telephone sockets. Connect RJ45

data connectors only to these sockets.

 The AC wall socket-outlet must be near the PD-9001GR

and easily accessible. You can remove AC power from

the PD-9001GR by disconnecting the AC power cord

from either the wall socket-outlet or the PD-9001GR

appliance coupler.

 The PD-9001GR Data In and Data & Power Out

interfaces are qualified as Safety Extra-Low Voltage

(SELV) circuits according to IEC 60950-1. Connect

these interfaces only to SELV interfaces on other

equipment.

WARNINGS!

 Connect the PD-9001GR only to the IP device with

which it was bought. Using the PD-9001GR with other IP

devices can cause damage to the IP device.

 Read the installation instructions before connecting the

PD-9001GR to its power source.

 Follow basic electricity safety measures whenever

connecting the PD-9001GR to its power source.

 A voltage mismatch can cause equipment damage and

may pose a fire hazard. If the voltage indicated on the

label is different from the power outlet voltage, do not

connect the PD-9001GR to that power outlet.



Troubleshooting

Symptom

Corrective Steps

PD-

9001GR

does not

power up

1. Verify that a reliable power cord

is used.

2. Verify that the voltage at the

power inlet is between 100 and 240

VAC.

3. Remove and re-apply power to

the device and check the indicators

during power up sequence.

The PD

does not

operate

1. Verify that the PD-9001GR

detects a PD.

2. Verify that the PD is designed for

PoE operation.

3. Verify that you are using a

standard Category 5/5e/6,

straight-wired cable, with four pairs.

4. If an external power splitter is in

use, replace it with a known-good

splitter.

5. Ensure input Ethernet cable is

connected to the Data In port.

6. Verify that the PD is connected

to the Data & Power port.

7. Try to reconnect the same PD

into a different PD-9001GR. If it

works, there is probably a faulty port

or RJ45 connection.

8. Verify that there is no short over

any of the twisted pair cables or

over the RJ45 connectors.

The end

device

operates,

but there

is no data

link

1. Verify that the port indicator on

the front panel is continuously lit.

2. If an external power splitter is in

use, replace it with a known-good

splitter.

3. Verify that for this link, you are

using standard UTP/FTP Category 5

straight (non-crossover) cabling,

with all four pairs.

4. Verify that the Ethernet cable

length is less than 100 meters from

the Ethernet source to the

load/remote terminal.

5. Try to reconnect the same PD

into a different PD-9001GR. If it

works, there is probably a faulty port

or RJ45 connection.

Port Connectivity

Indication

Ethernet

Cat . 5 Cable

Terminal

Figure 1: Connecting the PD-9001GR

Indicators

Port LED

Indicated Behavior

Yellow On

Power is on (power is active)

Green On

A remote terminal is connected

Green Blinking

Overload state or short-circuit

Specifications

Environmental Specifications

Mode

Temperature

Humidity

Operating

0° to +40° C

32° to +104° F

10 to 90%; (no

condensation

allowed)

Storage

-20° to +70° C

-4° to +158° F

10 to 90%; (no

condensation

allowed)

Electrical Specifications

Input Voltage

100 - 240 VAC (50/60 Hz)

Maximal Input Current

0.67 Ampere

Guaranteed Output power

30 Watts

Nominal Output Voltage

55 VDC

Ethernet Interface

Input (Data In): Ethernet

10/100/1000Base-T

RJ45 female socket

Output (Data & Power

Out): Ethernet

10/100/1000Base-T, plus

55 VDC

RJ45 female socket, with

DC voltage on wire pairs,

4-5 (+) & 7-8 (-).

Functions and Features

The PD-9001GR Power over Ethernet (PoE) Single Port Midspan

offers a compact and cost effective power

solution for IP phones, WLAN access points, network cameras

and other IP terminal installations.

The PD-9001GR converts AC power to 55VDC power is then

provided over the Ethernet cable.

The PD-9001GR supports up to Mbps pass through

data rates. The single port PD-9001GR can be powered via

universal AC input.

PD-9001GR EMC Compliance:

 FCC Part 15 class B and EN55022 class B

 EN55024

 VCCI

PD-9001GR Safety Compliance:

 UL/cUL per 60950-1 2nd Ed.

 GS mark

Preliminary Steps

 Apply AC power to the PD-9001GR, using an

operational AC cable with an appropriate ground

connection.

 Connect an output Ethernet cable to the Data & Power

Out port.

 Verify that a power ready Ethernet compatible device is

connected.

WARNING

Do not use cross over cable between the PD-9001GR output

port and the load device

Installation

The PD-9001GR can be placed on a desktop.

: Before placing the PD-9001GR:

 Do not to cover PD-9001GR or block the airflow to the

PoE with any foreign objects. Keep the PD-9001GR

away from excessive heat and humidity and free from

vibration and dust.

 Ensure that the cable length from Ethernet network

source to the terminal does not exceed 100 meters

(330 feet). The PoE is not a repeater and does not

amplify the Ethernet data signal.

 Use a splitter if desired; ensure that the splitter is

connected close to the terminal and not on the

PD-9001GR!

 No “on-off” switch exists; simply plug the PD-9001GR

into an AC power source.

Installing the Unit

Refer to Figure 1.

1. Using a standard power cord, connect the PD-9001GR to an

AC outlet (100 - 240 VAC),

2. Connect the Data In jack (input) to the remote Ethernet

network switch's Patch panel and the Data & Power Out jack

(output) to the terminal.