DEBUGADPTR1USB - SILICON LABS - Datasheet.Live

Rev. 0.3 1/15 Copyright © 2015 by Silicon Laborato ries 8-Bit USB Debug Adapter

8-Bit USB Debug Adapter

8-BIT USB DEBUG ADAPTER USER’S GUIDE

1. Introduction

The 8-bit USB Debug Adapter (UDA) provides the interface between the PC ’s USB port and the Silicon Labs 8-bit

target device’s in-system debug/programming circuitry. The 10-pin ribbon cable connects the adapter to the target

board and the target device’s debug interface.

Figure 1. 8-Bit USB Debug Adapter

Visit www.silabs.com/8bit-uda for ordering information.

2. Relevant Documentation

Application notes can be found on the 8-bit MCU Application Notes web page: www.silabs.com/appnotes.

AN124: Pin Sharing Techniques for the C2 Interface—Describes in detail the de bug interface pin

sharing feature for C2 devices, which enables debugging and use of the /RST and GPIO pins shared with

C2CK and C2D.

AN117: Using C8051Fxxx On-Chip Interface Utilities DLL—The SiUtil DLL discussed in this document

uses the USB Debug Adapter to program the memory space of C2 and JTAG devices.

AN134: Multiple-Device JTAG Configuration in the Silicon Labs IDE—Configuration in the IDE and

using the USB Debug Adapter for devices in a JTAG chain.

8-Bit USB Debug Adapter

2 Rev. 0.3

3. Pinout Specification

The 8-Bit USB Debug Adapter supports both Silicon Laboratories JTAG and C2 debug interfaces , and the adapter

is powered from the USB connection to the PC. The UDA is also capab le of p roviding power to the target device or

other circuitry via pin 10 of the connector. Table 1 shows the pin definitions for the UDA keyed connector. The part

number for the matching shroude d and keyed connector for a PCB is 2510-6002UB from 3M.

The USB Debug Adapter can automatically change the communication voltage level based on the level detected

on pin 7 of the connector . As a result, this pin should be pulled high with a strong pull-up (~1 kΩ) for noise immunity

purposes and not pulled down to ground.

Notes:

• The USB Debug Adapter requires a target system clock of 32 kHz or greater.

• With the default settings, the USB Debug Adapter can supply up to 100 mA to a target system.

Figure 2. 8-Bit USB Debug Adapter Connector

Table 1. USB Debug Adapter Debug Connector Pin Descriptions

Pin # Description Details

1 Not Connected

2 GND (Ground)

3 GND (Ground)

4 TCK / C2D JTAG TCK or C2 Data

5 TMS / C2CK pin share JTAG TMS or C2 Clock pin sharing

6 TDO / C2D pin share JTAG TDO or C2 Data pin sharing

7 TDI / C2CK JTAG TDI or C2 Clock signal

This pin is used by the UDA to sense and set

the logic voltage level. This pin should never

have a pull-down to ground.

8 Not Connected

9 GND (Ground)

10 USB Power 5 V power from the UDA

1

2

3

4

9

8

7

6

5

10

8-Bit USB Debug Adapter

Rev. 0.3 3

4. Minimum C2 Programming Connections

The minimu m required program ming connections for the C2 interface are C2D (pin 4), C2CK (pin 7), and ground

(pins 2, 3, or 9).

5. Hardware Setup using a USB Debug Adapter

Connect a target board to a PC running the Silicon Laboratories IDE via the USB Debug Adapter as shown in

Figure 3.

1. Connect the USB Debug Adapter’s 10-pin ribbon cable to the JTAG or Debug connector on the target

board.

2. Connect one end of a standard USB cable to the USB connector on the USB Debug Adapter.

3. Connect the other end of the USB cable to a USB Port on the PC.

4. Power the target board.

Notes:

•Use the Reset button in the IDE to reset the target when connected using a USB Debug Adapter.

• Remove power from the target board and the USB Debug Adapter before connecting or disconnecting the

ribbon cable from the target boar d. Connecting or disconnecting the ca ble when the devices have power can

damage the device and/or the USB Debug Adapter.

Figure 3. Hardware Setup using a USB Debug Adapter

6. USB Drivers

The USB Debug Adapter uses the Human Interface Device (HID) USB interface to communicate with the PC.

Since most operating systems have this driver automatically built in, no drivers need to be inst alled to use th e UDA.

1

2

3

8-Bit USB Debug Adapter

4 Rev. 0.3

7. Software Setup using a USB Debug Adapter

The Silicon Laboratories Integrated Development Environment (IDE) along with other software tools are provided

for device development and debugging. The IDE is available for download from the Silicon Laboratories website

(www.silabs.com/mcudownloads) and is also available on microcontroller development kit CD-ROMs.

7.1. Configuring the USB Debug Adapter in the Silicon Labs IDE

Once the IDE has been installed and the hardware has been connected as shown in Section 5, follow the steps

below to built a project, connect and download to a target board using the USB Debug Adapter.

1. Select ProjectOpen Project... to ope n a pr ev iou s ly

saved project.

2. Before connecting to the target device, several

connection options may need to be set. Open the

Connection Options window (shown in Figure 4) by

selecting OptionsConnection Options... in the IDE

menu.

3. Select USB Debug Adapter in the Serial Adapter

section.

4. If more than one adapter is connected, choose the

appropriate serial number from the drop-down list.

5. Check the Power target after disconnect option if the

target board is currently being powered by the USB

Debug Adapter. The board will remain powered after a

software disconnect by the IDE.

6. Next, the correct Debug Interface must be selected.

Check the Debug Interface corresponding to the

Silicon Laboratories device on the target board.

7. Once all the selections are mad e, click the OK button to

close the window.

8. Click the Connect button in the toolbar or select

DebugConnect from the menu to connect to the

device.

9. Download the project to the target by clicking the

Download Code button in the toolbar.

10. Save the project when finished with the debug se ssion

to preserve the current target build configuration, editor settings and the loca tion of all ope n debug vie ws.

To save the project, select ProjectSave Project As... from the menu. Create a new name for the

project and click on Save.

Figure 4. Connection Options

8-Bit USB Debug Adapter

Rev. 0.3 5

8. Schematics

Figure 5. 8-Bit USB Debug Adapter Schematic (1 of 2)

8-Bit USB Debug Adapter

6 Rev. 0.3

Figure 6. 8-Bit USB Debug Adapter Schematic (2 of 2)

Disclaimer

Silicon Laboratories intends to provide customers with the latest, accurate, and in-depth documentation of all peripherals and modules available for system and software implementers

using or intending to use the Silicon Laboratories products. Characterization data, available modules and peripherals, memory sizes and memory addresses refer to each specific

device, and "Typical" parameters provided can and do vary in different applications. Application examples described herein are for illustrative purposes only. Silicon Laboratories

reserves the right to make changes without further notice and limitation to product information, specifications, and descriptions herein, and does not give warranties as to the accuracy

or completeness of the included information. Silicon Laboratories shall have no liability for the consequences of use of the information supplied herein. This document does not imply

or express copyright licenses granted hereunder to design or fabricate any integrated circuits. The products must not be used within any Life Support System without the specific

written consent of Silicon Laboratories. A "Life Support System" is any product or system intended to support or sustain life and/or health, which, if it fails, can be reasonably expected

to result in significant personal injury or death. Silicon Laboratories products are generally not intended for military applications. Silicon Laboratories products shall under no

circumstances be used in weapons of mass destruction including (but not limited to) nuclear, biological or chemical weapons, or missiles capable of delivering such weapons.

Trademark Information

Silicon Laboratories Inc., Silicon Laboratories, Silicon Labs, SiLabs and the Silicon Labs logo, CMEMS®, EFM, EFM32, EFR, Energy Micro, Energy Micro logo and combinations

thereof, "the world’s most energy friendly microcontrollers", Ember®, EZLink®, EZMac®, EZRadio®, EZRadioPRO®, DSPLL®, ISOmodem ®, Precision32®, ProSLIC®, SiPHY®,

USBXpress® and others are trademarks or registered trademarks of Silicon Laboratories Inc. ARM, CORTEX, Cortex-M3 and THUMB are trademarks or registered trademarks of

ARM Holdings. Keil is a registered trademark of ARM Limited. All other products or brand names mentioned herein are trademarks of their respective holders.

http://www.silabs.com

Silicon Laboratories Inc.

400 West Cesar Chavez

Austin, TX 78701

USA

Simplicity Studio

One-click access to MCU and

wireless tools, documentation,

software, source code libraries &

more. Available for Windows,

Mac and Linux!

IoT Portfolio

www.silabs.com/IoT SW/HW

www.silabs.com/simplicity Quality

www.silabs.com/quality Support and Community

community.silabs.com