BCW70LT1G General Purpose Transistor PNP Silicon Features * These Devices are Pb-Free, Halogen Free/BFR Free and are RoHS http://onsemi.com Compliant COLLECTOR 3 MAXIMUM RATINGS Symbol Value Unit Collector-Emitter Voltage Rating VCEO -45 Vdc Emitter-Base Voltage VEBO -5.0 Vdc IC -100 mAdc 2 EMITTER Symbol Max Unit 3 PD 225 mW 1.8 mW/C RqJA 556 C/W PD 300 mW 2.4 mW/C RqJA 417 C/W TJ, Tstg -55 to +150 C Collector Current - Continuous 1 BASE THERMAL CHARACTERISTICS Characteristic Total Device Dissipation FR-5 Board (Note 1) TA = 25C Derate above 25C Thermal Resistance, Junction-to-Ambient Total Device Dissipation Alumina Substrate, (Note 2) @TA = 25C Derate above 25C Thermal Resistance, Junction-to-Ambient Junction and Storage Temperature 1 2 SOT-23 (TO-236AB) CASE 318 STYLE 6 MARKING DIAGRAM Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. FR-5 = 1.0 x 0.75 x 0.062 in. 2. Alumina = 0.4 x 0.3 x 0.024 in. 99.5% alumina H2 M G G 1 H2 = Device Code M = Date Code* G = Pb-Free Package (Note: Microdot may be in either location) *Date Code orientation and/or overbar may vary depending upon manufacturing location. ORDERING INFORMATION Device Package Shipping BCW70LT1G SOT-23 (Pb-Free) 3000 / Tape & Reel For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. (c) Semiconductor Components Industries, LLC, 2009 August, 2009 - Rev. 3 1 Publication Order Number: BCW70LT1/D BCW70LT1G ELECTRICAL CHARACTERISTICS (TA = 25C unless otherwise noted) Symbol Characteristic Min Max Unit -45 - Vdc -50 - Vdc -5.0 - Vdc - - -100 -10 nAdc mAdc 215 500 - - -0.3 Vdc -0.6 -0.75 Vdc - 7.0 pF - 10 dB OFF CHARACTERISTICS Collector-Emitter Breakdown Voltage (IC = -2.0 mAdc, IB = 0) V(BR)CEO Collector-Emitter Breakdown Voltage (IC = -100 mAdc, VEB = 0) V(BR)CES Emitter-Base Breakdown Voltage (IE = -10 mAdc, IC = 0) V(BR)EBO Collector Cutoff Current (VCB = -20 Vdc, IE = 0) (VCB = -20 Vdc, IE = 0, TA = 100C) ICBO ON CHARACTERISTICS DC Current Gain (IC = -2.0 mAdc, VCE = -5.0 Vdc) hFE Collector-Emitter Saturation Voltage (IC = -10 mAdc, IB = -0.5 mAdc) VCE(sat) Base-Emitter On Voltage (IC = -2.0 mAdc, VCE = -5.0 Vdc) VBE(on) SMALL-SIGNAL CHARACTERISTICS Output Capacitance (IE = 0, VCB = -10 Vdc, f = 1.0 MHz) Cobo Noise Figure (IC = -0.2 mAdc, VCE = -5.0 Vdc, RS = 2.0 kW, f = 1.0 kHz, BW = 200 Hz) http://onsemi.com 2 NF BCW70LT1G TYPICAL NOISE CHARACTERISTICS (VCE = - 5.0 Vdc, TA = 25C) 10 7.0 IC = 10 mA 5.0 In, NOISE CURRENT (pA) en, NOISE VOLTAGE (nV) 1.0 7.0 5.0 BANDWIDTH = 1.0 Hz RS 0 30 mA 3.0 100 mA 300 mA 1.0 mA 2.0 BANDWIDTH = 1.0 Hz RS IC = 1.0 mA 3.0 2.0 300 mA 1.0 0.7 0.5 100 mA 30 mA 0.3 0.2 1.0 10 mA 0.1 10 20 50 100 200 500 1.0k f, FREQUENCY (Hz) 2.0k 5.0k 10 10k 20 50 Figure 1. Noise Voltage 100 200 500 1.0k 2.0k f, FREQUENCY (Hz) 5.0k 10k Figure 2. Noise Current NOISE FIGURE CONTOURS 1.0M 500k BANDWIDTH = 1.0 Hz 200k 100k 50k 20k 10k 0.5 dB 5.0k 1.0 dB 2.0k 1.0k 500 2.0 dB 3.0 dB 200 100 RS , SOURCE RESISTANCE (OHMS) RS , SOURCE RESISTANCE (OHMS) (VCE = - 5.0 Vdc, TA = 25C) 20 30 50 70 100 200 300 IC, COLLECTOR CURRENT (mA) BANDWIDTH = 1.0 Hz 200k 100k 50k 20k 10k 0.5 dB 5.0k 1.0 dB 2.0k 1.0k 500 2.0 dB 3.0 dB 200 100 5.0 dB 10 1.0M 500k 500 700 1.0k 5.0 dB 10 20 RS , SOURCE RESISTANCE (OHMS) Figure 3. Narrow Band, 100 Hz 1.0M 500k 30 50 70 100 200 300 IC, COLLECTOR CURRENT (mA) 500 700 1.0k Figure 4. Narrow Band, 1.0 kHz 10 Hz to 15.7 kHz 200k 100k 50k Noise Figure is Defined as: NF + 20 log10 20k 10k 0.5 dB 1.0 dB 2.0 dB 3.0 dB 5.0 dB 200 100 10 20 30 50 70 100 200 300 en2 ) 4KTRS ) In 2RS2 12 4KTRS en = Noise Voltage of the Transistor referred to the input. (Figure 3) I = Noise Current of the Transistor referred to the input. n (Figure 4) K = Boltzman's Constant (1.38 x 10-23 j/K) T = Temperature of the Source Resistance (K) R = Source Resistance (Ohms) 5.0k 2.0k 1.0k 500 S 500 700 1.0k IC, COLLECTOR CURRENT (mA) Figure 5. Wideband http://onsemi.com 3 BCW70LT1G 100 1.0 TA = 25C IC, COLLECTOR CURRENT (mA) VCE , COLLECTOR-EMITTER VOLTAGE (VOLTS) TYPICAL STATIC CHARACTERISTICS 0.8 IC = 1.0 mA 0.6 10 mA 50 mA 100 mA 0.4 0.2 TA = 25C PULSE WIDTH = 300 ms 80 DUTY CYCLE 2.0% 300 mA 200 mA 150 mA 40 100 mA 20 50 mA 5.0 10 0 20 5.0 10 15 20 25 30 35 VCE, COLLECTOR-EMITTER VOLTAGE (VOLTS) Figure 6. Collector Saturation Region V, TEMPERATURE COEFFICIENTS (mV/C) TJ = 25C V, VOLTAGE (VOLTS) 1.2 1.0 0.8 VBE(sat) @ IC/IB = 10 0.6 VBE(on) @ VCE = 1.0 V 0.4 0.2 VCE(sat) @ IC/IB = 10 0 0.5 1.0 2.0 5.0 10 20 IC, COLLECTOR CURRENT (mA) 50 1.6 *APPLIES for IC/IB hFE/2 0.8 - 55C to 25C 0.8 25C to 125C 1.6 2.4 0.1 100 300 50 0.5 1.0 2.0 5.0 10 20 IC, COLLECTOR CURRENT (mA) 100 ts VCC = - 3.0 V IC/IB = 10 IB1 = IB2 TJ = 25C 200 t, TIME (ns) t, TIME (ns) 0.2 - 55C to 25C 1000 700 500 VCC = 3.0 V IC/IB = 10 TJ = 25C 100 70 50 30 tr 20 100 70 50 30 td @ VBE(off) = 0.5 V 10 7.0 5.0 1.0 qVB for VBE Figure 9. Temperature Coefficients 500 200 25C to 125C *qVC for VCE(sat) 0 Figure 8. "On" Voltages 300 40 Figure 7. Collector Characteristics 1.4 0.2 250 mA 60 0 0 0.002 0.005 0.01 0.02 0.05 0.1 0.2 0.5 1.0 2.0 IB, BASE CURRENT (mA) 0.1 IB = 400 mA 350 mA tf 20 2.0 3.0 20 30 5.0 7.0 10 IC, COLLECTOR CURRENT (mA) 50 70 10 -1.0 100 Figure 10. Turn-On Time - 2.0 - 3.0 - 5.0 - 7.0 -10 - 20 - 30 IC, COLLECTOR CURRENT (mA) Figure 11. Turn-Off Time http://onsemi.com 4 - 50 - 70 -100 BCW70LT1G 500 10 TJ = 25C TJ = 25C 7.0 VCE = 20 V Cib C, CAPACITANCE (pF) 300 5.0 V 200 100 5.0 3.0 2.0 Cob 70 50 0.5 0.7 1.0 r(t) TRANSIENT THERMAL RESISTANCE (NORMALIZED) f, T CURRENT-GAIN -- BANDWIDTH PRODUCT (MHz) TYPICAL DYNAMIC CHARACTERISTICS 2.0 3.0 5.0 7.0 10 20 30 1.0 0.05 50 0.1 0.2 0.5 1.0 2.0 5.0 IC, COLLECTOR CURRENT (mA) VR, REVERSE VOLTAGE (VOLTS) Figure 12. Current-Gain -- Bandwidth Product Figure 13. Capacitance 1.0 0.7 0.5 10 20 50 D = 0.5 0.3 0.2 0.2 0.1 0.1 0.07 0.05 FIGURE 16 0.05 P(pk) 0.02 0.03 0.02 t1 0.01 0.01 0.01 0.02 SINGLE PULSE 0.05 0.1 0.2 0.5 1.0 t2 2.0 5.0 10 20 50 t, TIME (ms) 100 200 DUTY CYCLE, D = t1/t2 D CURVES APPLY FOR POWER PULSE TRAIN SHOWN READ TIME AT t1 (SEE AN-569) ZqJA(t) = r(t) w RqJA TJ(pk) - TA = P(pk) ZqJA(t) 500 1.0k 2.0k 5.0k 10k 20k 50k 100 Figure 14. Thermal Response DESIGN NOTE: USE OF THERMAL RESPONSE DATA 104 IC, COLLECTOR CURRENT (nA) VCC = 30 V A train of periodical power pulses can be represented by the model as shown in Figure 16. Using the model and the device thermal response the normalized effective transient thermal resistance of Figure 14 was calculated for various duty cycles. To find ZqJA(t), multiply the value obtained from Figure 14 by the steady state value RqJA. 103 ICEO 102 101 ICBO AND ICEX @ VBE(off) = 3.0 V 10-1 Example: Dissipating 2.0 watts peak under the following conditions: t1 = 1.0 ms, t2 = 5.0 ms (D = 0.2) Using Figure 14 at a pulse width of 1.0 ms and D = 0.2, the reading of r(t) is 0.22. 10-2 The peak rise in junction temperature is therefore DT = r(t) x P(pk) x RqJA = 0.22 x 2.0 x 200 = 88C. 100 -4 0 -2 0 0 + 20 + 40 + 60 + 80 + 100 + 120 + 140 + 160 TJ, JUNCTION TEMPERATURE (C) For more information, see AN-569. Figure 15. Typical Collector Leakage Current http://onsemi.com 5 BCW70LT1G PACKAGE DIMENSIONS SOT-23 (TO-236) CASE 318-08 ISSUE AN NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. 318-01 THRU -07 AND -09 OBSOLETE, NEW STANDARD 318-08. D SEE VIEW C 3 HE E c 1 2 e b DIM A A1 b c D E e L L1 HE 0.25 q A L A1 L1 VIEW C MIN 0.89 0.01 0.37 0.09 2.80 1.20 1.78 0.10 0.35 2.10 MILLIMETERS NOM MAX 1.00 1.11 0.06 0.10 0.44 0.50 0.13 0.18 2.90 3.04 1.30 1.40 1.90 2.04 0.20 0.30 0.54 0.69 2.40 2.64 MIN 0.035 0.001 0.015 0.003 0.110 0.047 0.070 0.004 0.014 0.083 INCHES NOM 0.040 0.002 0.018 0.005 0.114 0.051 0.075 0.008 0.021 0.094 MAX 0.044 0.004 0.020 0.007 0.120 0.055 0.081 0.012 0.029 0.104 STYLE 6: PIN 1. BASE 2. EMITTER 3. COLLECTOR SOLDERING FOOTPRINT* 0.95 0.037 0.95 0.037 2.0 0.079 0.9 0.035 SCALE 10:1 0.8 0.031 mm inches *For additional information on our Pb-Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. "Typical" parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including "Typicals" must be validated for each customer application by customer's technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303-675-2175 or 800-344-3860 Toll Free USA/Canada Fax: 303-675-2176 or 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com N. American Technical Support: 800-282-9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81-3-5773-3850 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative BCW70LT1/D