http://www.tracopower.com Page 1 of 3
DC/DC Converters
TEL 5 Series, 5 Watt
Features
Wide 2:1 input range
Cost efficient SMD-design
High power density
High efficiency up to 86%
Regulated outputs
I/O isolation 1500 VDC
I nput filter to meet EN 55022, Class A
and FCC, level A without external
components
Indefinite short-circuit protection
24-pin DIP with industry standard pinout
High reliability, MTBF >1 Mio. h
Lead free design, RoHS compliant
3-year product warranty
The TEL 5 Series is a range of DC/DC-converter modules with wide input range
of 2:1. State of the art SMD-technology guarantees a product with very high reli-
ability and excellent cost /performance ratio. High efficiency allows an operating
temperature range of –40°C to +85°C at full load. This product series provides an
economical solution for many cost critical applications in industrial and consumer
electronics.
Ordercode Input voltage range Output voltage Output current max. Efficiency typ.
TEL 5-1210 3.3 VDC 1200 mA 77 %
TEL 5-1211 9 – 18 VDC 5 VDC 1000 mA 81 %
TEL 5-1212 (nominal 12 VDC) 12 VDC 500 mA 84 %
TEL 5-1222 ±12 VDC ±250 mA 84 %
TEL 5-1223 ±15 VDC ±200 mA 84 %
TEL 5-2410 3.3 VDC 1200 mA 79 %
TEL 5-2411 18 – 36 VDC 5 VDC 1000 mA 83 %
TEL 5-2412 (nominal 24 VDC) 12 VDC 500 mA 86 %
TEL 5-2422 ±12 VDC ±250 mA 86 %
TEL 5-2423 ±15 VDC ±200 mA 86 %
Models
UL 60950 -1
C B
Scheme
http://www.tracopower.com Page 2 of 3
All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated.
Input Specifications
Input current no load /full load 12 Vin models: 20 mA / 590 mA typ.
24 Vin models: 5 mA / 290 mA typ.
Start-up voltage / 12 Vin models: 8.0 VDC / 8.0 VDC
under voltage shut down 24 Vin models: 16.0 VDC / 16.0 VDC
Surge voltage (1 sec. max.) 12 Vin models: 25 V max.
24 Vin models: 50 V max.
Reverse voltage protection 1.0 A max.
Conducted noise (input) EN 55022 class A, FCC part 15 level A
Output Specifications
Voltage set accuracy ±1 %
Regulation – Input variation Vin min. to Vin max. 0.3 % max.
– Load variation 20 – 100 %
single output models 1 % max
dual output models balanced load 2 % max.
Minimum load 5 % of rated max current (operating at lower
load condition is safe but the modules may not
meet all spscifications listed)
Ripple and noise (20 MHz Bandwidth) 75 mVpk-pk max.
Temperature coefficient ±0.02 %/K
Output current limitation >120 % of Iout max., constant current
Short circuit protection continuous (automatic recovery)
Capacitive load single output models: 6800 µF max.
dual output models: 1000 µF max. (each output)
General Specifications
Temperature ranges Operating 40°C to +85°C
– Case temperature +90°C
– Storage –40°C to +125°C
Derating (convection cooling) 3.3 %/K above 70°C
Humidity (non condensing) 95 % rel H max.
Reliability, calculated MTBF (MIL-HDBK-217F at +25°C, ground benign) >1 Mio. h
Isolation voltage (60 sec.) – Input/Output 1500 VDC
Isolation capacitance – Input/Output 380 pF typ.
Isolation resistance – Input/Output (500 VDC) >1‘000 M Ohm
Switching frequency 300 kHz typ.
Safety standards UL/cUL 60950-1, IEC/EN 60950-1
Environmental compliance – Reach www.tracopower.com/info/reach-declaration.pdf
– RoHs RoHS directive 2011/65/EU
DC/DC Converters
TEL 5 Series 5 Watt
Page 3 of 3
Specifications can be changed without notice! Make sure you are using the latest documentation, downloadable at www.tracopower.com
www.tracopower.com
Physical Specifications
Casing material non conductive plastic (UL 94V-0 rated)
Weight 17 g (0.60 oz)
Soldering temperature max. 265°C / 10 sec.
Outline Dimensions
5.0
(0.2)
4.5 22.86 (0.9)
20.3
2.54
32 (1.25)
10.2
(0.4)
15.24
(0.6)
911
2223
23
16 14
Bottom view
15.24 (0.6) 5.08
2.4
(0.8)
(0.1)
(0.18)
(0.1) (0.2)
Pin Single Dual
2–Vin (GND) –Vin (GND)
3–Vin (GND) –Vin (GND)
9No pin Common
11 No con. –Vout
14 +Vout +Vout
16 –Vout Common
22 +Vin (Vcc) +Vin (Vcc)
23 +Vin (Vcc) +Vin (Vcc)
Pin-Out
DC/DC Converters
TEL 5 Series 5 Watt
Rev. December 4, 2018
Dimensions in [mm], () = Inch
Pin diameter ø 0.5 ±0.05 (0.02 ±0.002)
Tolerances ±0.25 (±0.01)
Pin pitch tolerances ±0.13 (±0.005)