THCV215-B - CEL - Datasheet.Live

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

1/25

THCV215 and THCV216

V-by-One® HS High-speed Video Data Transmitter and Receiver

General Description

THCV215 and THCV216 are designed to support

video data transmission between the host and

display.

The chipset can transmit 39bit video data and 3bit

sync data via only a single differential cable at an

LVDS clock frequency from 20MHz to 100MHz.

The chipset, which has two high-speed data lanes,

can transmit the video data up to 1080p/10b/60Hz,

1080p/12b/60Hz. The maximum serial data rate is

3.75Gbps/lane.

Color

Depth

Link

LVDS

Clock Frequency

6bit

Single/Dual

20MHz to 100MHz

8bit

Single/Dual

20MHz to 100MHz

10bit

Single/Dual

20MHz to 85MHz

12bit

Single/Dual

20MHz to 75MHz

Features

Color depth selectable: 6/8/10/12 bit

Single/Dual Link selectable

AC coupling

LVDS Input internal termination

CORE 1.8V, LVDS 3.3V

Package: 64 pin TSSOP

Wide frequency range

CDR requires no external frequency reference

Supports Spread Spectrum Clocking: Up to

30kHz/0.5%(center spread)

V-by-One® HS standard Version1.4 compliant

Block Diagram

TLA0+/-

・

TLF0+/-

TLCLK0+/-

TLA1+/-

・

TLF1+/-

TLCLK1+/-

Color depth

(6/8/10/12)

Single/Dual

Pre-emphasis

PDN

LVDS

Deserializer

LVDS

Deserializer

Formatter

SerializerSerializerPLL

・

Controls HTPDN

LOCKN

Color depth

(6/8/10/12)

Single/Dual

PDN

DeserializerDeserializer

CDR

Deskew & Formatter

PLL LVDS

Serializer LVDS

Serializer

Controls

THCV215 THCV216 RLA0+/-

・

RLF0+/-

RLCLK0+/-

RLA1+/-

・

RLF1+/-

RLCLK1+/-

・

TX0+

TX0- RX0+

RX0-

TX1+

TX1- RX1+

RX1-

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

2/25

Contents Page

General Description ................................................................................................................................................. 1

Features .................................................................................................................................................................... 1

Block Diagram ......................................................................................................................................................... 1

Pin Diagram ............................................................................................................................................................. 3

Pin Description ......................................................................................................................................................... 4

Functional Description ............................................................................................................................................ 5

Absolute Maximum Ratings0F ............................................................................................................................. 13

Operating Conditions ............................................................................................................................................ 13

Electrical Specifications ........................................................................................................................................ 14

AC Timing Diagrams and Test Circuits ............................................................................................................... 17

Package ................................................................................................................................................................... 24

Notices and Requests ............................................................................................................................................. 25

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

3/25

Pin Diagram

LAGND 1 64 LPVDL LPVDH 164 LAGND

LAVDH 263 LPGND LPGND 263 LAVDH

TLA0- 3 62 SDSEL SDSEL 362 RLA0-

TLA0+ 4 61 COL1 COL1 461 RLA0+

TLB0- 5 60 COL0 COL0 560 RLB0-

TLB0+ 6 59 RDY HTPDN 659 RLB0+

TLC0- 7 58 PDN LOCKN 758 RLC0-

TLC0+ 8 57 HTPDN VDL 857 RLC0+

TLCLK0- 9 56 LOCKN GND 956 RLCLK0-

TLCLK0+ 10 55 VDL CPVDL0 10 55 RLCLK0+

TLD0- 11 54 GND CPGND0 11 54 RLD0-

TLD0+ 12 53 CAVDL CAVDL 12 53 RLD0+

TLE0- 13 52 CAGND CAGND 13 52 RLE0-

TLE0+ 14 51 TX0- RX0- 14 51 RLE0+

TLF0- 15 50 TX0+ RX0+ 15 50 RLF0-

TLF0+ 16 49 CAGND CAGND 16 49 RLF0+

TLA1- 17 48 TX1- CAGND 17 48 RLA1-

TLA1+ 18 47 TX1+ RX1- 18 47 RLA1+

TLB1- 19 46 CAGND RX1+ 19 46 RLB1-

TLB1+ 20 45 CAVDL CAGND 20 45 RLB1+

TLC1- 21 44 CPGND CAVDL 21 44 RLC1-

TLC1+ 22 43 CPVDL CPGND1 22 43 RLC1+

TLCLK1- 23 42 DRV1 CPVDL1 23 42 RLCLK1-

TLCLK1+ 24 41 DRV0 GND 24 41 RLCLK1+

TLD1- 25 40 PRE1 VDL 25 40 RLD1-

TLD1+ 26 39 PRE0 Reserved1 26 39 RLD1+

TLE1- 27 38 Reserved0 PDN 27 38 RLE1-

TLE1+ 28 37 Reserved1 Reserved2 28 37 RLE1+

TLF1- 29 36 GND Reserved3 29 36 RLF1-

TLF1+ 30 35 VDL RS 30 35 RLF1+

LAVDH 31 34 LPGND LPGND 31 34 LAVDH

LAGND 32 33 LPVDL LPVDH 32 33 LAGND

THCV216

64pin

TSSOP

THCV215

64pin

TSSOP

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

4/25

Pin Description

THCV215 THCV216

Pin Name Pin # Type* Description Pin Name Pin # Type* Description

TX0 +/- 50,51 CO RX0 +/- 15,14 CI

TX1 +/- 47,48 CO RX1 +/- 19,18 CI

TLA0+/- 4,3 LI RLA0+/- 61,62 LO

TLB0+/- 6,5 LI RLB0+/- 59,60 LO

TLC0+/- 8,7 LI RLC0+/- 57,58 LO

TLCLK0+/- 10,9 LI RLCLK0+/ 55,56 LO

TLD0+/- 12,11 LI RLD0+/- 53,54 LO

TLE0+/- 14,13 LI RLE0+/- 51,52 LO

TLF0+/- 16,15 LI RLF0+/- 49,50 LO

TLA1+/- 18,17 LI RLA1+/- 47,48 LO

TLB1+/- 20,19 LI RLB1+/- 45,46 LO

TLC1+/- 22,21 LI RLC1+/- 43,44 LO

TLCLK1+/- 24,23 LI RLCLK1+/ 41,42 LO

TLD1+/- 26,25 LI RLD1+/- 39,40 LO

TLE1+/- 28,27 LI RLE1+/- 37,38 LO

TLF1+/- 30,29 LI RLF1+/- 35,36 LO

LOCKN 56 I Lock detect input LOCKN 7 O Lock detect output (open drain)

HTPDN 57 I Hot plug detect input HTPDN 6 O Hot plug detect output (open drain)

PDN 58 I

Power down input

H: Normal Operation

L: Power down (CML output High Fix,

other High-Z)

PDN 27 I

Power down input

H: Normal Operation

L: Power down (High-Z)

COL1,

COL0

61,60 I

Color depth select input

L,L: 6bit

L,H: 8bit

H,L: 10bit

H,H: 12bit

COL1,

COL0

4,5 I

Color depth select input

L,L: 6bit

L,H: 8bit

H,L: 10bit

H,H: 12bit

SDSEL 62 I

Single/Dual select input

L: Channel0 enable, Channel1 disable

H: Channel0, Channel1 enable

SDSEL 3 I

Single/Dual select input

L: Channel0 enable, Channel1 disable

H: Channel0, Channel1 enable

DRV1 42 I Must be tied to GND

DRV0 41 I Must be tied to VDL

PRE1,

PRE0

40,39 I

Pre-emphasis level select input

L,L: 0%

H,L: 100%

L,H: not available

H,H: not available

RDY 59 O

Link status ready output

L: not ready

H: ready

Reserved

1,2

26,28 I Must be tied to GND

Reserved1 37 I

Field BET mode enable input

L: Normal operation (default)

H: Field BET mode enabled

Reserved3 29 I

Field BET mode enable input

L: Normal operation (default)

H: Field BET mode enabled

Reserved0 38 I Must be tied to GND VDL 8,25 P 1.8V power supply pin for digital circuitry

GND 9,24 P Ground pin for digital circuitry

CAVDL 12,21 P 1.8V power supply pin for CML input

GND 36,54 P Ground pin for digital circuitry CAGND

13,16,

17,20

P Ground pin for CML input

CAVDL 45,53 P 1.8V power supply pin for CML output CPVDL0 10 P 1.8V power supply pin for PLL circuitry

CAGND 46,49,52 P Ground pin for CML output CPGND0 11 P Ground pin for PLL circuitry

CPVDL 43 P 1.8V power supply pin for PLL circuitry CPVDL1 23 P 1.8V power supply pin for PLL circuitry

CPGND 44 P Ground pin for PLL circuitry CPGND1 22 P Ground pin for PLL circuitry

LPVDL 33,64 P

1.8V power supply pin for LVDS PLL

LPVDH 1,32 P

3.3V power supply pin for LVDS PLL

LPGND 34,63 P Ground pin for LVDS PLL circuitry LPGND 2,31 P Ground pin for LVDS PLL circuitry

LAVDH 2,31 P 3.3V power supply pin for LVDS input LAVDH 34,63 P 3.3V power supply pin for LVDS output

LAGND 1,32 P Ground pin for LVDS input LAGND 33,64 P Ground pin for LVDS output

*type symbol

Note) All CMOS inputs are 1.8V-inputs I=1.8V CMOS Input, O=1.8V CMOS Output, IO3=3.3V CMOS I/O

except for THCV216's RS LI=LVDS Input, LO= LVDS Output

CI=CML Input, CO=CML Output

P=Power

VDL

35,55

1.8V power supply pin for digital circuitry

IO3

Direction of RS pin depends on

Reserved3.

LVDS swing range select input

when Reserved3=L

H: Normal swing (350mV typ.)

L: Reduced swing (200mV typ.)

Field BET output when Reserved3=H.

Goes LOW when errors detected.

CML Data Input

LVDS Data Output

LVDS Data Input

CML Data Output

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

5/25

Functional Description

Functional Overview

With V-by-One®HS’s proprietary encoding scheme and CDR (Clock and Data Recovery) architecture, THCV215

and THCV216 enable transmission of 18/24/30/36bits per pixel video data (Rn/Gn/Bn/CONTn), Hsync

(HSYNCn), Vsync (VSYNCn) data and Data Enable (DE) by single/dual differential pair cable with minimal

external components.

THCV215, the transmitter, inputs LVDS data (including video data, Hsync, Vsync and DE) and serializes video

data and Hsync, Vsync data separately, depending on the polarity of DE. DE is a signal which indicates whether

video or Hsync, Vsync data are active. When DE is high, it serializes video data inputs into a single differential

data stream. And it transmits serialized Hsync, Vsync data when DE is low.

THCV216, the receiver, automatically extracts the clock from the incoming data stream and converts the serial

data into video data with DE being high or Hsync, Vsync data with DE being low, recognizing which type of

serial data is being sent by the transmitter. And it outputs the recovered data in the form of LVDS data.

THCV216 can seamlessly operate for a wide range of a serial bit rate from 600Mbps to 3.75Gbps/channel,

detecting the frequency of an incoming data stream, and recovering both the clock and data by itself.

It does not need any external frequency reference, such as a crystal oscillator.

Data Enable Requirement (DE)

There are some requirements for DE as described in Figure 2, Figure 3 and Table 15.

Dual LVDS input to THCV215 should be synchronized in terms of DE transition. See Figure 2.

If DE=Low, Hsync and Vsync data of same cycle are transmitted. Otherwise video data of that are transmitted

(DE=High). SYNC data from receiver in DE=High period are previous data of DE transition. See Figure 3.

The length of DE being low and high is at least 2 clock cycles long as described in Table 15.

Data Enable must be toggled like High -> Low -> High at regular interval.

Figure 1. Conceptual diagram of the basic operation of the chipset

Figure 2. Service condition of DE input synchronization

Vdiff = (TLCLK0+) – (TLCLK0-)

Vdiff = (TLCLK1+) – (TLCLK1-)

Vdiff = (TLC0+) – (TLC0-)

Vdiff = (TLC1+) – (TLC1-)

DE DE DE DE DE DE

THCV

216

THCV

215

D[39:0]

Hsync

Vsync

Rn/Gn/Bn

CONTn

HSYNCn

VSYNCn

D[39:0]

Hsync

Vsync

Rn/Gn/Bn

CONTn

HSYNCn

VSYNCn

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

6/25

VSYNCn

HSYNCn

Rn/Gn/Bn

CONTn

tDEH tDEL

1 cycle

Valid Data Valid Data

Low LowValid Data

Low High

Keep the last data

of DE=L period

THCV216

Output

Low

VSYNC

HSYNC

Rn/Gn/Bn

CONTn

tDEH tDEL

1 cycle

Valid Data Valid Data

Invalid InvalidValid Data

Low High

Invalid

THCV215

Input

Low

n=0,1

Figure 3. Video and sync data transmission timing diagram

Single/Dual Link mode function (SDSEL)

SDSEL

Mode

Function

Single

Channel 0 active and channel 1 power down

Dual

Both channel 0 and channel 1 active

Table 1. Single/Dual mode select

Color Depth mode function (COL [1:0])

COL[1:0]

Color Depth

LVDS Clock Frequency Range

L,L

6bit

20MHz to 100MHz

L,H

8bit

20MHz to 100MHz

H,L

10bit

20MHz to 85MHz

H,H

12bit

20MHz to 75MHz

Table 2. Color depth mode select

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

7/25

LVDS Mapping

LVDS data (video data, Hsync, Vsync, DE) are mapped as Figure 4. TLC0[6] is special bit for DE(data enable),

and TLC0[5:4] are for Hsync, Vsync data bits and the other bits are for video data.

The number of LVDS channel depends on color depth mode(COL[1:0]).

If SDSEL=Low, only channel 0 (Figure 4, n=0) is active. If SDSEL=High, both channel 0/1(Figure 4, n=0/1) are

active. (TLC1[6:4] are not available).

Depending on color mode, TLD1[6] and TLD0[6] are not available. See Table 3.

TLAn6

Vdiff = (TLCLKn +) - (TLCLKn-)

n=0,1

TLAn5 TLAn4 TLAn3 TLAn2 TLAn1 TLAn0 TLAn6 TLAn5 TLAn4 TLAn3 TLAn2 TLAn1

tTCIP

Vdiff=0V

next cyclecurrent cycle

TLAn1 TLAn0

previous cycle

TLBn6 TLBn5 TLBn4 TLBn3 TLBn2 TLBn1 TLBn0 TLBn6 TLBn5 TLBn4 TLBn3 TLBn2 TLBn1TLBn1 TLBn0

TLCn6

(DE) TLCn5

(V) TLCn4

(H) TLCn3 TLCn2 TLCn1 TLCn0 TLCn3 TLCn2 TLCn1TLCn1 TLCn0

TLDn6 TLDn5 TLDn4 TLDn3 TLDn2 TLDn1 TLDn0 TLDn6 TLDn5 TLDn4 TLDn3 TLDn2 TLDn1TLDn1 TLDn0

TLEn6 TLEn5 TLEn4 TLEn3 TLEn2 TLEn1 TLEn0 TLEn6 TLEn5 TLEn4 TLEn3 TLEn2 TLEn1TLEn1 TLEn0

TLFn6 TLFn5 TLFn4 TLFn3 TLFn2 TLFn1 TLFn0 TLFn6 TLFn5 TLFn4 TLFn3 TLFn2 TLFn1TLFn1 TLFn0

TLAn +/-

TLBn +/-

TLCn +/-

TLDn +/-

TLEn +/-

TLFn +/-

Control data bitData Enable

TLCn6

(DE) TLCn5

(V) TLCn4

(H)

Color depth

12,10, 8, 6

Figure 4. LVDS mapping timing diagram

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

8/25

L,L (6bit) L,H (8bit) H,L (10bit) H,H (12bit)

TLAn[0] RLAn[0] Rn[0] Rn[2] Rn[4] Rn[6] D2

TLAn[1] RLAn[1] Rn[1] Rn[3] Rn[5] Rn[7] D3

TLAn[2] RLAn[2] Rn[2] Rn[4] Rn[6] Rn[8] D4

TLAn[3] RLAn[3] Rn[3] Rn[5] Rn[7] Rn[9] D5

TLAn[4] RLAn[4] Rn[4] Rn[6] Rn[8] Rn[10] D6

TLAn[5] RLAn[5] Rn[5] Rn[7] Rn[9] Rn[11] D7

TLAn[6] RLAn[6] Gn[0] Gn[2] Gn[4] Gn[6] D10

TLBn[0] RLBn[0] Gn[1] Gn[3] Gn[5] Gn[7] D11

TLBn[1] RLBn[1] Gn[2] Gn[4] Gn[6] Gn[8] D12

TLBn[2] RLBn[2] Gn[3] Gn[5] Gn[7] Gn[9] D13

TLBn[3] RLBn[3] Gn[4] Gn[6] Gn[8] Gn[10] D14

TLBn[4] RLBn[4] Gn[5] Gn[7] Gn[9] Gn[11] D15

TLBn[5] RLBn[5] Bn[0] Bn[2] Bn[4] Bn[6] D18

TLBn[6] RLBn[6] Bn[1] Bn[3] Bn[5] Bn[7] D19

TLCn[0] RLCn[0] Bn[2] Bn[4] Bn[6] Bn[8] D20

TLCn[1] RLCn[1] Bn[3] Bn[5] Bn[7] Bn[9] D21

TLCn[2] RLCn[2] Bn[4] Bn[6] Bn[8] Bn[10] D22

TLCn[3] RLCn[3] Bn[5] Bn[7] Bn[9] Bn[11] D23

TLCn[4] RLCn[4] HSYNCn HSYNCn HSYNCn HSYNCn Hsync

TLCn[5] RLCn[5] VSYNCn VSYNCn VSYNCn VSYNCn Vsync

TLCn[6] RLCn[6] DEn(*2) DEn(*2) DEn(*2) DEn(*2) DE

TLDn[0] RLDn[0] Rn[0] Rn[2] Rn[4] D0

TLDn[1] RLDn[1] Rn[1] Rn[3] Rn[5] D1

TLDn[2] RLDn[2] Gn[0] Gn[2] Gn[4] D8

TLDn[3] RLDn[3] Gn[1] Gn[3] Gn[5] D9

TLDn[4] RLDn[4] Bn[0] Bn[2] Bn[4] D16

TLDn[5] RLDn[5] Bn[1] Bn[3] Bn[5] D17

TLDn[6] RLDn[6] N/A(*1) CONTn[1] CONTn[3] D25(*3)

TLEn[0] RLEn[0] Rn[0] Rn[2] D30

TLEn[1] RLEn[1] Rn[1] Rn[3] D31

TLEn[2] RLEn[2] Gn[0] Gn[2] D28

TLEn[3] RLEn[3] Gn[1] Gn[3] D29

TLEn[4] RLEn[4] Bn[0] Bn[2] D26

TLEn[5] RLEn[5] Bn[1] Bn[3] D27

TLEn[6] RLEn[6] CONTn[2] CONTn[4] D24(*3)

TLFn[0] RLFn[0]

Channel

Power

Rn[0] D38

TLFn[1] RLFn[1] Rn[1] D39

TLFn[2] RLFn[2] Gn[0] D36

TLFn[3] RLFn[3] Gn[1] D37

TLFn[4] RLFn[4] Bn[0] D34

TLFn[5] RLFn[5] Bn[1] D35

TLFn[6] RLFn[6] CONTn[1] D33

n=0,1 : if SDSEL=L, Channel 1(n=1) is power down

*1 N/A: Not available, THCV216 output RLDn[6]=Low.

*2 DE must be same polarity(TLC0[6] = TLC1[6]) when SDSEL=H

*3 3D information flags defined in the V-by-One® HS Standard are assigned to the following bit.

V-by-One® HS Standard Packer/Unpacker D[24](3DLR) <=> LVDS T/RLEn[6]

V-by-One® HS Standard Packer/Unpacker D[25](3DEN) <=> LVDS T/RLDn[6]

Symbol defined by

V-by-One® HS

THCV215

Input

THCV216

Output

Color depth (COL[1:0])

Symbol defined by

V-by-One® HS

Channel

Power

Down

Channel

Power

Down

Channel

Power

Down

Channel

Power

Down

Channel

Power

Down

Table 3. LVDS mapping table

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

9/25

CML Buffer

CAVDL

TXn + RXn +

TXn - RXn -

Vterm ~ 1.3V

C=75～

200nF

50Ω

n=0,1

CAVDL

CAGND

THCV215 THCV216

CML

Transmitter CML

Receiver

50ΩC=75～

200nF

50Ω

Zdiff=100Ω

Figure 5. CML buffer scheme

Lock detect and Hot-plug function

LOCKN and HTPDN are both open drain output from THCV216. Pull-up resistors are needed at THCV215 side

to VDL. See Figure 6.

If THCV216 is not active (power down mode (PDN=L) or powered off), HTPDN is open. Otherwise, HTPDN is

pulled down by THCV216.

HTPDN of THCV215 side is High when THCV216 is not active or the receiver board is not connected. Then

THCV215 enters into the power down mode. When HTPDN transits from High to Low, THCV215 starts up and

transmits training pattern for link training.

LOCKN indicates whether THCV216 is in the lock state or not. If THCV216 is in the unlock state, LOCKN is

open. Otherwise (in the lock state), it’s pulled down by THCV216.

THCV215 keeps transmitting training pattern until LOCKN transits to Low. After training done, THCV216 sinks

current and LOCKN is Low. Then THCV215 starts transmitting normal video pattern.

VDL

(THCV215 side)

VDL

(THCV215 side)

HTPDN

LOCKN

10kΩ

THCV215 THCV216

10kΩ

Figure 6. Hot-plug and Lock detect scheme

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

10/25

No HTPDN connection option

HTPDN connection between THCV215 and THCV216 can be omitted as an application option. In this case,

HTPDN at the Transmitter side should always be taken ad Low. See Figure 7.

Figure 7. HTPDN is not connected scheme

VDL

(THCV215 side)

HTPDN

LOCKN

10kΩ

THCV215 THCV216

HTPDN

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

11/25

THCV215 Pre-emphasis function (PRE [1:0])

Pre-emphasis can equalize severe signal degradation caused by long distance or high-speed transmission.

Two pins, PRE1 and PRE0, select the strength of pre-emphasis. See Table 4.

PRE[1:0]

Description

L,L

w/o Pre-emphasis

H,L

w/ 100% Pre-emphasis

L,H / H,H

Not available

Table 4. Pre-emphasis function table

THCV215 Power Down function (PDN)

By setting the PDN pin to low, it results in the power down mode. All the internal circuitry turns off and the

both TXn+/- (n=0, 1) outputs turn to VDL.

THCV216 Power Down function (PDN)

By setting the PDN pin to low, it results in the power down mode. All the internal circuitry turns off and the

RLXn+/- (X=A, B, C, D, E, F, CLK, n=0, 1) outputs turn to High-Z.

THCV215 Link Ready function (RDY)

This is a CMOS output for indicating the link status. RDY=High if link is ready.

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

12/25

Field BET Operation

In order to help users to check the validity of high speed serial links (CML lines), THCV215/THCV216 have

an operation mode in which they act as the bit error tester (BET). In this mode, THCV215 internally generates a

test pattern, which is then serialized onto the CML high speed lines. THCV216 receives the data stream and

checks the sampled data for bit errors.

This "Field BET" mode is activated by setting Reserved1= H on THCV215 and Reserved3= H on THCV216

(Refer to Table 5).

In the Field BET mode, the on-chip pattern generator on THCV215 is enabled and generates the test pattern as

long as the LVDS clocks (TLCLK0+/-, TLCLK1+/-) are applied. Other LVDS data inputs may be left open or

applied with any pattern. They are ignored by THCV215. The generated data pattern is then 8b/10b encoded,

scrambled, and serialized onto the CML channels. As for THCV216, the internal test pattern check circuit gets

enabled and the RS pin, which is normally an input, turns into an output for the pattern checker (LVDS output

level is internally configured to be "Normal Swing”). The RS pin goes LOW whenever bit errors occur, and it

stays HIGH when there is no bit error. Please Refer to Figure 8.

Product

THCV215

THCV216

Pin Name

Reserved1

Reserved3

Normal

3.3V INPUT

H: Normal Swing, L: Reduced Swing

Field BET

3.3V OUTPUT

Goes LOW when bit errors occur.

Table 5. Field BET Operation Pin Settings

Figure 8. Field BET Configuration

THCV215 THCV216

LVDS clock to

TLCLK0, 1

Reserved1=H

(Field BET mode) Reserved3=H

(Field BET mode)

Test

Pattern

Checker

Test Pattern

Generator

LVDS data inputs

are ignored

STest Point

for

Field BET

LVDS Swing Select

for

Normal Operation

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

13/25

Absolute Maximum Ratings0F



Parameter Min. Typ. Max.

Units

1.8V Supply Voltage（VDL,CAVDL,CPVDL,LPVDL）-0.3 - +2.1 V

3.3V Supply Voltage(LAVDH) -0.3 - +4.0 V

1.8V CMOS Input Voltage -0.3 - VDL+0.3 V

1.8V CMOS Output Voltage -0.3 - VDL+0.3 V

LVDS Receiver Input Voltage -0.3 - LAVDH+0.3 V

CML Transmitter Output Voltage -0.3 - CAVDL+0.3 V

Output Current -50 - 50 mA

Storage Temperature -55 - +125 °C

Junction Temperature - - +125 °C

Reflow Peak Temperature / Time - - +260/10sec °C

Table 6. THCV215 Absolute Maximum Ratings

Parameter Min. Typ. Max.

Units

1.8V Supply Voltage(VDL,CAVDL,CPVDL0,CPVDL1) -0.3 - +2.1 V

3.3V Supply Voltage(LPVDH,LAVDH) -0.3 - +4.0 V

1.8V CMOS Input Voltage -0.3 - VDL+0.3 V

3.3V CMOS Input Voltage -0.3 - LAVDH+0.3

CMOS Output Voltage -0.3 - +2.1 V

CML Receiver Input Voltage -0.3 - CAVDL+0.3 V

LVDS Transmitter Output Voltage -0.3 - LAVDH+0.3 V

Output Current -30 - 30 mA

Storage Temperature -55 - +125 °C

Junction Temperature - - +125 °C

Reflow Peak Temperature / Time - - +260/10sec °C

Maximum Power Dissipation @+25℃- - 2 W

Lead Temperature (Soldering, 10sec) - - +260 °C

Table 7. THCV216 Absolute Maximum Ratings

Operating Conditions

Parameter Min. Typ. Max.

Units

1.8V Supply Voltage（VDL,CAVDL,CPVDL,LPVDL）1.62 1.80 1.98 V

3.3V Supply Voltage(LAVDH) 3.00 3.30 3.60 V

Operating Temperature 0 - 70 ℃

Table 8. THCV215 Operating Conditions

Parameter Min. Typ. Max.

Units

1.8V Supply Voltage(VDL,CAVDL,CPVDL0,CPVDL1)

except for the 12 bit color depth mode

1.62 1.80 1.98 V

1.8V Supply Voltage(VDL,CAVDL,CPVDL0,CPVDL1)

for the 12 bit color depth mode

1.71 1.80 1.89 V

3.3V Supply Voltage(LPVDH,LAVDH) 3.00 3.30 3.60 V

Operating Temperature 0 - 70 ℃

Table 9. THCV216 Operating Conditions

 “Absolute Maximum Ratings” are those values beyond which the safety of the device can not be guaranteed.

They are not meant to imply that the device should be operated at these limits. The tables of “Electrical

Characteristics” specify conditions for device operation.

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

14/25

Electrical Specifications

1.8V & 3.3V CMOS DC Specifications

Symbol Parameter Conditions Min. Typ. Max. Units

VIH High Level Input Voltage 0.65×VDL - VDL V

VIL Low Level Input Voltage 0 - 0.35×VDL V

VOH High Level Output Voltage IOH=-2mA VDL-0.45 - - V

VOL Low Level Output Voltage IOL=2mA - - 0.2 V

IIH Input Leak Current High VIN=VDL - - ±10 uA

IIL Input Leak Current Low VIN=0V - - ±10 uA

VIH3 High Level Input Voltage (3.3V inputs) 2.1 - LAVDH V

VIL3 Low Level Input Voltage (3.3V inputs) 0 - 0.8 V

VOH3 High Level Output Voltage (3.3V outputs) IOH=-4mA 2.4 - - V

VOL3 Low Level Output Voltage (3.3V outputs) IOL=4mA - - 0.4 V

IIH3 Input Leak Current High (3.3V inputs) VIN=LAVDH - - ±10 uA

IIL3 Input Leak Current Low (3.3V inputs) VIN=0V - - ±10 uA

Table 10. THCV215 and THCV216 1.8V & 3.3V CMOS DC Specifications

CML & LVDS DC Specifications

Symbol Parameter Conditions Min. Typ. Max. Units

VTTH LVDS Differential Input High Threshold - - 100 mV

VTTL LVDS Differential Input Low Threshold -100 - - mV

ITIH LVDS Input Leak Current High

PDN=L,

TLxn+/-=LAVDH

- - ±10 uA

ITIL LVDS Input Leak Current Low TLxn+/-=0V,PDN=L - - ±10 uA

RTIN LVDS Differential Input Resistance PDN=L 80 100 120 W

VTOD CML Differential Mode Output Voltage

DRV[1:0]=L,H

PRE[1:0]=L,L

200 300 400 mV

PRE[1:0]=L,L - 0 - %

PRE[1:0]=H,L 80 100 120 %

PRE[1:0]=L,L mV

PRE[1:0]=H,L mV

ITOH CML Output Leak Current High PDN=L - ±10 uA

ITOS CML Output Short Circuit Current CAVDL=1.8V -90 - - mA

PRE

CML Pre-emphasis Level

CAVDL-VTOD

CAVDL-2×VTOD

VTOC

CML Common Mode Output Voltage

Table 11. THCV215 CML & LVDS DC Specifications

Symbol Parameter Conditions Min. Typ. Max. Units

VRTH CML Differential Input High Threshold - - 50 mV

VRTL CML Differential Input Low Threshold -50 - mV

IRIH CML Input Leak Current High

PDN=L,

RXn+/-=CAVDL

- - ±10 uA

IRIL CML Input Leak Current Low PDN=L,RXn+/-=0V - - ±10 uA

IRRIH CML Input Current High RXn+/-=CAVDL - - 2 mA

IRRIL CML Input Current Low RXn+/-=0V -6 - - mA

RRIN CML Differential Input Resistance 80 100 120 W

LVDS Differential Mode Output Voltage

(Normal Swing)

RL=100Ω, RS=H 250 350 450 mV

LVDS Differential Mode Output Voltage

(Reduced Swing)

RL=100Ω, RS=L 100 200 300 mV

ΔVROD

Change in VROD between

Complementary Output States

RL=100Ω - - 35 mV

VROC LVDS Common Mode Output Voltage RL=100Ω 1.125 1.25 1.375 V

ΔVROC

Change in VROC between

Complementary Output States

RL=100Ω - - 35 mV

IROS LVDS Output Short Circuit Current RLxn+/-=0V -24 - - mA

IROZ LVDS Output TRI-STATE Current

PDN=L,

RLxn+/-=0V / LAVDH

x=A~F,CLK, n=0, 1

- - ±10 uA

VROD

Table 12. THCV216 CML & LVDS DC Specifications

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

15/25

Supply Currents

Symbol Parameter Conditions Min. Typ. Max. Units

ITCCW

Supply Current for 1.8V Power Supply

(Worst Case Pattern)

COL[1:0]=H,H

PRE[1:0]=H,L

SDSEL=H

- - 210 mA

ITCCW33

Supply Current for 3.3V Power Supply

(Worst Case Pattern)

COL[1:0]=H,H

PRE[1:0]=H,L

SDSEL=H

- - 90 mA

ITCCS

Power Down Supply Current

PDN=L

All Inputs

=Fixed L or H

- - 200 uA

Table 13. THCV215 Supply Currents

Symbol Parameter Conditions Min. Typ. Max. Units

IRCCW

Supply Current for 1.8V Power Supply

(Worst Case Pattern)

COL[1:0]=H,H

SDSEL=H

RS=H

- - 160 mA

IRCCW33

Supply Current for 3.3V Power Supply

(Worst Case Pattern)

COL[1:0]=H,H

SDSEL=H

RS=H

- - 190 mA

IRCCS

Power Down Supply Current

PDN=L

All Inputs

=Fixed L or H

- - 200 uA

Table 14. THCV216 Supply Currents

Vdiff = (TLCLKn +) - (TLCLKn-)

n=0,1 tTCIP

Vdiff=0V

next cyclecurrent cycleprevious cycle

TLAn +/-

TLBn +/-

TLCn +/-

TLDn +/-

TLEn +/-

TLFn +/-

Control bitData Enable

H H

Figure 9. Worst Case Pattern

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

16/25

Switching Characteristics

Symbol Parameter Conditions Min. Typ. Max. Units

tDEH DE=High Duration 2tTCIP - - sec

tDEL DE=Low Duration 2tTCIP - - sec

Table 15. DE requirement

Symbol Parameter Conditions Min. Typ. Max. Units

COL[1:0]=L,L | L,H 10 -50 ns

COL[1:0]=H,L 11.76 - 50 ns

COL[1:0]=H,H 13.3 - 50 ns

tTCIH LVDS Differential Clock High Time 2×tTCIP/7 - 5×tTCIP/7 ns

tTCIL LVDS Differential Clock Low Time 2×tTCIP/7 - 5×tTCIP/7 ns

tTCIP=75MHz -440 - 440 ps

tTCIP=85MHz -390 - 390 ps

tTCIP=100MHz -330 - 330 ps

tTIP1 LVDS Input Data Position0 -tSK 0 +tSK ns

tTIP0 LVDS Input Data Position1 tTCIP/7-tSK tTCIP/7 tTCIP/7+tSK ns

tTIP6 LVDS Input Data Position2 2×tTCIP/7-tSK 2×tTCIP/7 2×tTCIP/7+tSK ns

tTIP5 LVDS Input Data Position3 3×tTCIP/7-tSK 3×tTCIP/7 3×tTCIP/7+tSK ns

tTIP4 LVDS Input Data Position4 4×tTCIP/7-tSK 4×tTCIP/7 4×tTCIP/7+tSK ns

tTIP3 LVDS Input Data Position5 5×tTCIP/7-tSK 5×tTCIP/7 5×tTCIP/7+tSK ns

tTIP2 LVDS Input Data Position6 6×tTCIP/7-tSK 6×tTCIP/7 6×tTCIP/7+tSK ns

tTISK Lane0/1 LVDS Input Clock Skew -0.3×tTCIP - 0.3×tTCIP ns

tTRF CML Output Rise and Fall Time(20%-80%) 50 -150 ps

tTOSK CML Lane0/1 Output Inter Pair Skew -2 - 2 UI

tTCD Input Clock to Output Data Delay

(56/(5×n)+6.1)

×tTCIP-5 (1)

(56/(5×n)+6.1)

×tTCIP+5 (1)

tTPD Power On to PDN High Delay 0 - - ns

tTPLL0 PDN High to CML Output Delay - - 10 ms

tTPLL1 PDN Low to CML Output High Fix Delay - - 20 ns

tTNP0

LOCKN High to Training Pattern Output

Delay

- - 10 ms

tTNP1

LOCKN Low to Data Pattern Output

Delay

- - 10 ms

(1) n =3, 4, and 5 for 6/8bit, 10bit, and 12bit mode, respectively.

tTCIP

tSK

TLCLK Period

LVDS Receiver Skew Margin

Table 16. THCV215 Switching Characteristics

Symbol Parameter Conditions Min. Typ. Max. Units

COL[1:0]=L,L | L,H 333 tTCIP/30 1667 ps

COL[1:0]=H,L 294 tTCIP/40 1250 ps

COL[1:0]=H,H 266 tTCIP/50 1000 ps

tRISK CML Lane0/1 Input Inter Pair Skew Margin - - 15 UI

tRLVT LVDS Differential Output Transition Time - 0.6 1.5 ns

tROP1 LVDS Output Data Position0 -0.25 0 0.25 ns

tROP0 LVDS Output Data Position1 tTCIP/7-0.25 tTCIP/7 tTCIP/7+0.25 ns

tROP6 LVDS Output Data Position2 2×tTCIP/7-0.25 2×tTCIP/7

2×tTCIP/7+0.25

tROP5 LVDS Output Data Position3 3×tTCIP/7-0.25 3×tTCIP/7

3×tTCIP/7+0.25

tROP4 LVDS Output Data Position4 4×tTCIP/7-0.25 4×tTCIP/7

4×tTCIP/7+0.25

tROP3 LVDS Output Data Position5 5×tTCIP/7-0.25 5×tTCIP/7

5×tTCIP/7+0.25

tROP2 LVDS Output Data Position6 6×tTCIP/7-0.25 6×tTCIP/7

6×tTCIP/7+0.25

tROSK Lane0/1 LVDS Output Clock Skew - - 50 ps

tRDC Input Data to Output Clock Delay

(178+68×n)

×tRBIT-5 (1)

(178+68×n)

×tRBIT+5 (1)

tRPD Power On to PDN High Delay 0 - - ns

tRHPD0 PDN High to HTPDN Low Delay - - 1 us

tRHPD1 PDN Low to HTPDN High Delay - - 1 us

tRPLL0

Training Pattern Input to LOCKN Low

Delay

- - 10 ms

tRPLL1 PDN Low to LOCKN High Delay - - 10 us

tRLCK0 LOCKN Low to LVDS Output Delay - - 1 ms

tRLCK1 LOCKN High to LVDS High-Z Delay - - 0 ns

(1) n =3, 4, and 5 for 6/8bit, 10bit, and 12bit mode, respectively.

Unit Interval

tRBIT

Table 17. THCV216 Switching Characteristics

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

17/25

AC Timing Diagrams and Test Circuits

THCV215 LVDS Input Switching Characteristics

TLxn6

Vdiff = (TLCLKn +) - (TLCLKn-)

x=A,B,C,D,E,F

n=0,1

TLxn5 TLxn4 TLxn3 TLxn2 TLxn1 TLxn0 TLxn6 TLxn5 TLxn4 TLxn3 TLxn2 TLxn1

Vdiff = (TLxn +) - (TLxn-)

tTCIP

Vdiff=0V

tTIP1

tTIP0

tTIP6

tTIP5

tTIP4

tTIP3

tTIP2

Vdiff = (TLCLK0 +) - (TLCLK0-) Vdiff=0V

Vdiff = (TLCLK1 +) - (TLCLK1-) Vdiff=0V

tTISK

tTCIH tTCIL

Figure 10. THCV215 LVDS Input Switching Timing Diagrams

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

18/25

THCV216 LVDS Output Switching Characteristics

RLxn6

Vdiff = (RLCLKn +) - (RLCLKn-)

x=A,B,C,D,E,F

n=0,1

RLxn5 RLxn4 RLxn3 RLxn2 RLxn1 RLxn0 RLxn6 RLxn5 RLxn4 RLxn3 RLxn2 RLxn1

Vdiff = (RLxn +) - (RLxn-)

tROP1

tROP0

tROP6

tROP5

tROP4

tROP3

tROP2

tTCIP

Vdiff=0V

Vdiff = (RLCLK0 +) - (RLCLK0-) Vdiff=0V

Vdiff = (RLCLK1 +) - (RLCLK1-) Vdiff=0V

tROSK

Figure 11. THCV216 LVDS Output Switching Timing Diagrams

RL=100Ω

5pF

20%

80%

RLxn+

RLxn-

x=A,B,C,D,E,F

n=0,1

Vdiff = (RLxn +) - (RLxn-)

tRLVT tRLVT

Figure 12. THCV216 LVDS Output Switching Timing Diagram and Test Circuit.

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

19/25

THCV215 CML Output Switching Characteristics

TXn+

TXn-

n=0,1

75～200nF

< 5mm

20%

80%

Vdiff = (TXn +) - (TXn-)

tTRF tTRF

Vdiff = (TX0 +) - (TX0-) Vdiff=0V

Vdiff = (TX1 +) - (TX1-) Vdiff=0V

tTOSK

50Ω

Figure 13. THCV215 CML Output Switching Timing Diagrams and Test Circuit

THCV216 CML Input Switching Characteristics

Vdiff = (RX0 +) - (RX0-)

Vdiff = (RX1 +) - (RX1-)

Vdiff=0V

tRISK

Figure 14. THCV216 CML Input Timing Diagrams

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

20/25

DE period requirement

Figure 15. DE period requirement

Latency Characteristics

Vdiff = (TLCLK0 +) - (TLCLK0-) Vdiff=0V

tTCD

Vdiff = (TX0 +) - (TX0-)

Vdiff = (RX0 +) - (RX0-)

Vdiff=0V

tRDC

pixel 1st bit

Vdiff = (RLCLK0 +) - (RLCLK0-)

Figure 16. THCV215 and THCV216 Latency

Vdiff = (TLCLK0+) – (TLCLK0-)

Vdiff = (TLC0+) – (TLC0-)

DE DE DE DE DE DE

tDEH tDEL

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

21/25

Lock and Unlock Sequence

Power On

VDD18

VDD33

TLCLKn

HTPDN

PDN

LOCKN

Fix to VDD18 CDR Training

pattern ALN Training

Pattern CDR Training

pattern

tTPLL0 tTNP1 tTNP0 tTPLL1

TXn

LVDS Data PatternTLxn+/-

1.5V

tTPD

x=A,B,C,D,E,F

n=0,1

Normal

pattern

Low-level

LVDS Clock Pattern

Normal

pattern

Figure 17. THCV215 Lock/Unlock Sequence

RXn

Power On

VDD18

VDD33

HTPDN

PDN

LOCKN

CDR Training

Pattern

tRHPD0

tRPLL0

tRHPD1

RLx

High-Z

tRLCK0 tRLCK1

1.5V

tRPD

High-Z LVDS Data Pattern

RLCLK

x=A,B,C,D,E,F

n=0,1

ALN Training

Pattern Normal

pattern

tRPLL1

LVDS Clock Pattern

Figure 18. THCV216 Lock/Unlock Sequence

tTPD and tRPD minimum is 0sec; therefore, PDN can be applied at the same time as VDD18 and VDD33.

tTPLL0 is the time from “both PDN=High and HTPDN=Low“ moment to Training pattern ignition.

HTPDN could transit from High to Low under PDN=High condition at THCV215, which is different from what

Figure 17 indicates but is natural situation.

VDD18 : 1.8V power supply

VDD33 : 3.3V power supply

VDD18 : 1.8V power supply

VDD33 : 3.3V power supply

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

22/25

Note

1)HTPDN/LOCKN connection between high VDD V-by-One® HS transmitter and THCV216

When using THCV216 with high VDD V-by-One® HS transmitter, user have to take care of HTPDN/LOCKN

connection because THCV216 HTPDN/LOCKN output pins absolute maximum ratings are VDL+0.3V;

therefore high VDD pull-up at transmitter side can cause violation of usage. Users are supposed to connect

those HTPDN/LOCKN line between two devices with appropriate level-shifter configuration.

LOCKN

HTPDN

THCV216

1.8V

10kΩ

MOSFET

(Vth<1.2V)

1.8V

10kΩ

MOSFET

(Vth<1.2V)

3.3V

10kΩ

V-by-One®HS Transmitter

(Ex. THCV217,THCV233) 1.8V Tolerant

Transistor

V-by-One®HS Tx side PCB V-by-One®HS Rx side PCB

D S

2)LVDS input pin connection

When LVDS line is not drove from the previous device, the line is pulled up to 3.3V internally in

THCV215.This can cause violation of absolute maximum ratings to the previous LVDS Tx device whose

operating condition is lower voltage power supply than 3.3V. This phenomenon may happen at power on phase

of the whole system including THCV215. One solution for this problem is PD=L control during no LVDS input

period because pull-up resistors are cut off at power down state.

3)Power On Sequence

Don’t input TCLK#+/- before power supply to THCV215 is on in order to keep absolute maximum ratings.

4)Unused LVDS input pins

First, select appropriate color depth with COL0,COL1 pins. If there are inevitably remained LVDS no input

pins which are originally active, tie them to GND.

Second, avoid the situation that LVDS input pins in use are open. You can use PDN=L control during no

LVDS input period to cut off pulled-up resistors.

5)Cable Connection and Disconnection

Don’t connect and disconnect CML and LVDS cables, when the power is supplied to the system.

6)GND Connection

Connect the each GND of the PCB which Transmitter, Receiver and THCV215 on it. It is better for EMI

reduction to place GND cable as close to LVDS cable as possible.

LAVDH

LVDS input buffer

Internal circuit of THCV215

Low VDD

LVDS Tx

THCV215

LVDS Tx

integrated

device

LVDS Tx side PCB

LVDS Rx side PCB

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

23/25

7)Multi Drop Connection

Multi drop connection is not recommended.

8)Multiple counterpart use

Multiple counterpart use such as following system is not recommended.

p.15 tTISK spec should be kept.

Asynchronous use such as following system is not recommended.

9)Multiple device connection

HTPDN and LOCKN signals are supposed to be connected proper for their purpose like the following figure.

HTPDN should be from just one Rx to multiple Tx because its purpose is only ignition of all Tx.

LOCKN should be connected so as to indicate that all Rx CDR become ready to receive normal operation data.

LOCKN of Tx side can be simply split to multiple Tx.

There can be other applicable circuits like ‘OR gate of LOCKN’, ‘npn transistor with resistors as inverter’, etc.

Also possible time difference of internal processing time (p.15 THCV215 tTCD and THCV216 tRDC) on

multiple data stream must be accommodated and compensated by the following destination device connected to

multiple THCV216, which may have internal FIFO.

THCV215

HTPDN

LOCKN

THCV215

HTPDN

LOCKN

THCV216

HTPDN

LOCKN

PDN

THCV216

HTPDN

LOCKN

PDN

Source

Device Destination

Device

Ex. synchronized Time diff. comes up

clkin.1

clkin.2

clkout.1

clkout.2

Internal processing time tTCD Internal processing time tRDC

FIFO

LVDS Rx

CLK

DATA

THCV216

RLCLK0-

RLCLK0+

RLCLK1-

RLCLK1+

LVDS Tx

CLK

DATA

THCV215

TLCLK0-

TLCLK0+

TLCLK1-

TLCLK1+

LVDS Rx

THCV216

LVDS Rx

RLCLK0,1-

RLCLK0,1+

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

24/25

Package

64 Lead Molded Thin Shrink Small Outline Package, JEDEC

Figure 19. 64 pin TSSOP package physical dimension

0.50 NOM

0.17~0.27

17.00 ± 0.10

0.25 NOM

0.60 ± 0.15

1.00 NOM

0.10 ± 0.05

0.90 ± 0.10

1.20 MAX

Detail of Lead End Unit:mm

0.10

0°~8°

8.10 ± 0.20

6.10 ± 0.10

THCV215-216_Rev.2.70_E

THine Electronics, Inc.

Security E

25/25

Notices and Requests

1. The product specifications described in this material are subject to change without prior notice.

2. The circuit diagrams described in this material are examples of the application which may not always apply to

the customer's design. We are not responsible for possible errors and omissions in this material. Please note if

errors or omissions should be found in this material, we may not be able to correct them immediately.

3. This material contains our copyright, know-how or other proprietary. Copying or disclosing to third parties

the contents of this material without our prior permission is prohibited.

4. Note that if infringement of any third party's industrial ownership should occur by using this product, we will

be exempted from the responsibility unless it directly relates to the production process or functions of the

product.

5. Product Application

5.1 Application of this product is intended for and limited to the following applications: audio-video

device, office automation device, communication device, consumer electronics, smartphone, feature

phone, and amusement machine device. This product must not be used for applications that require

extremely high-reliability/safety such as aerospace device, traffic device, transportation device, nuclear

power control device, combustion chamber device, medical device related to critical care, or any kind of

safety device.

5.2 This product is not intended to be used as an automotive part, unless the product is specified as a

product conforming to the demands and specifications of ISO/TS16949 ("the Specified Product") in this

data sheet. THine Electronics, Inc. (“THine”) accepts no liability whatsoever for any product other than

the Specified Product for it not conforming to the aforementioned demands and specifications.

5.3 THine accepts liability for demands and specifications of the Specified Product only to the extent

that the user and THine have been previously and explicitly agreed to each other.

6. Despite our utmost efforts to improve the quality and reliability of the product, faults will occur with a certain

small probability, which is inevitable to a semi-conductor product. Therefore, you are encouraged to have

sufficiently redundant or error preventive design applied to the use of the product so as not to have our

product cause any social or public damage.

7. Please note that this product is not designed to be radiation-proof.

8. Testing and other quality control techniques are used to this product to the extent THine deems necessary

to support warranty for performance of this product. Except where mandated by applicable law or

deemed necessary by THine based on the user’s request, testing of all functions and performance of the

product is not necessarily performed.

9. Customers are asked, if required, to judge by themselves if this product falls under the category of strategic

goods under the Foreign Exchange and Foreign Trade Control Law.

10. The product or peripheral parts may be damaged by a surge in voltage over the absolute maximum ratings or

malfunction, if pins of the product are shorted by such as foreign substance. The damageｓ may cause a

smoking and ignition. Therefore, you are encouraged to implement safety measures by adding protection

devices, such as fuses.

THine Electronics, Inc.

sales@thine.co.jp

http://www.thine.co.jp/