KAOHSIUNG HITACHI ELECTRONICS CO., LTD. DATE: Jan. 28th 2011 FOR MESSRS: CUSTOMER'S ACCEPTANCE SPECIFICATION TX15D02VM0CAA Contents No. ITEM SHEET No. PAGE 1 COVER 7B64PS 2701-TX15D02VM0CAA-1 1-1/1 2 RECORD OF REVISION 7B64PS 2702-TX15D02VM0CAA-1 2-1/1 3 GENERAL DATA 7B64PS 2703-TX15D02VM0CAA-1 3-1/1 4 ABSOLUTE MAXIMUM RATINGS 7B64PS 2704-TX15D02VM0CAA-1 4-1/1 5 ELECTRICAL CHARACTERISTICS 7B64PS 2705-TX15D02VM0CAA-1 5-1/1 6 OPTICAL CHARACTERISTICS 7B64PS 2706-TX15D02VM0CAA-1 6-1/2~2/2 7 BLOCK DIAGRAME 7B64PS 2707-TX15D02VM0CAA-1 7-1/1 8 RELIABILITY TESTS 7B64PS 2708-TX15D02VM0CAA-1 8-1/1 9 LCD INTERFACE 7B64PS 2709-TX15D02VM0CAA-1 9-1/6~6/6 10 OUTLINE DIMENSIONS 7B63PS 2710-TX15D02VM0CAA-1 10-1/2~2/2 11 APPEARANCE STANDARD 7B64PS 2711-TX15D02VM0CAA-1 11-1/3~3/3 12 PRECAUTIONS 7B64PS 2712-TX15D02VM0CAA-1 12-1/2~2/2 13 DESIGNATION OF LOT MARK 7B64PS 2713-TX15D02VM0CAA-1 13-1/1~1/1 ACCEPTED BY: KAOHSIUNG HITACHI ELECTRONICS CO., LTD. PROPOSED BY: SHEET NO. 7B64PS 2701-TX15D02VM0CAA-1 PAGE 1-1/1 2. RECORD OF REVISION DATE SHEET No. KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SUMMARY SHEET NO. 7B64PS 2702-TX15D02VM0CAA-1 PAGE 2-1/1 3. GENERAL DATA 3.1 DISPLAY FEATURES This module is a 5.8" WQVGA of 15:9 format amorphous silicon TFT. The pixel format is vertical stripe and sub pixels are arranged as R (red), G (green), B (blue) sequentially.This display is RoHS compliant, COG (chip on glass) technology and LED backlight are applied on this display. Part Name TX15D02VM0CAA Module Dimensions 145.0(W) mm x 90.0(H) mm x 11.5 (D) mm typ. LCD Active Area 126.3(W) mm x 75.78(H) mm Pixel Pitch 0.105x3(RGB) (W) mm x 0.315 (H) mm Resolution 400 x 3(RGB)(W) x 240(H) dots Color Pixel Arrangement R, G, B Vertical stripe LCD Type Transmissive Color TFT; Normally Black Display Type Active Matrix Number of Colors 262k Colors Backlight 12 LEDs (3 series x 4) Weight 175 g Interface C-MOS; 6-bit RGB; 40 pins Power Supply Voltage 3.3V for LCD; 12V for Backlight Power Consumption 0.8 W for LCD ; 4.1W for Backlight Viewing Direction Super Wide Version (In Plane Switching) KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2703-TX15D02VM0CAA-1 PAGE 3-1/1 4. ABSOLUTE MAXIMUM RATINGS Item Symbol Min. Max. Unit Remarks Supply Voltage VDD -0.3 5.0 V - Input Voltage of Logic VI -0.3 VDD+0.3 V Note 1 Operating Temperature Top -30 80 C Note 2 C Note 2 V - Storage Temperature Tst -40 90 Backlight Input Voltage VLED - 15 Note 1: The rating is defined for the signal voltages of the interface such as DCLK,DE,and RGB data bus. Note 2: The maximum rating is defined as above based on the temperature on the panel surface, which might be different from ambient temperature after assembling the panel into the application. Moreover, some temperature-related phenomenon as below needed to be noticed: - Background color, contrast and response time would be different in temperatures other than 25 C . -Operating under high temperature will shorten LED lifetime. KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2704-TX15D02VM0CAA-1 PAGE 4-1/1 5. ELECTRICAL CHARACTERISTICS 5.1 LCD CHARACTERISTICS Ta 25 C , VSS 0V Item Symbol Condition Min. Typ. Max. Unit Remarks Power Supply Voltage VDD - 3.0 3.3 3.6 V - Input Voltage of Logic VI "H" level 0.7VDD - VDD+0.3 "L" level -0.3 - 0.25VDD V Note 1 Power Supply Current IDD VDD=3.3V - 240 300 mA Note 2,3 Vsync Frequency - 50 60 70 Hz - Hsync Frequency fv fH - 13.0 15.6 18.2 KHz - CLK Frequency f CLK - 7.5 9.0 10.5 MHz - Note1: The rating is defined for the signal voltages of the interface such as DE,DCLK and RGB data bus. Note 2: An all white check pattern is used when measuring IDD. f v is set to 60 Hz. Note 3: 1.0A fuse is applied in the module for IDD. For display activation and protection purpose, power supply is recommended larger than 2.5A to start the display and break fuse once any short circuit occurred. 5.2 BACKLIGHT CHARACTERISTICS Ta 25 C Item Symbol Condition Min. Typ. Max. Unit Remarks LED Input Voltage VLED - 11.5 12.0 12.5 V Note1 0V; 0% duty 320 340 360 3.0VDC; 100% duty - 30 36 mA Note 2 340 mA - 70K - hrs Note 3 LED Forward Current (Dim Control) ILED LED lifetime - Note 1: As Fig. 5.1 shown, LED current is constant, 340 mA, controlled by the LED driver when applying 12V VLED. Note 2: Dimming function can be obtained by applying DC voltage or PWM signal from the display interface CN1.The recommended PWM signal is 1K ~ 10K Hz with 3.3V amplitude. Note 3: The estimated lifetime is specified as the time to reduce 50% brightness by applying 340 mA at 25 C . Fig 5.1 KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2705-TX15D02VM0CAA-1 PAGE 5-1/1 6. OPTICAL CHARACTERISTICS The optical characteristics are measured based on the conditions as below: - Supplying the signals and voltages defined in the section of electrical characteristics. - The backlight unit needs to be turned on for 30 minutes. - The ambient temperature is 25 C . - In the dark room around 500~1000 lx, the equipment has been set for the measurements as shown in Fig 6.1. Ta 25 C , f v 60 Hz, VDD 3.3V Item Condition Symbol Brightness of White - Brightness Uniformity - Contrast Ratio Response Time (Rising + Falling) CR Tr Tf NTSC Ratio - Viewing Angle Red Green Max. - cd/m 70 - - % Note 2 500 800 - - Note 3 0 , 0 - - 45 ms Note 4 0 , 0 - 60 - % - Degree Note 5 - Note 6 ILED=340 mA - 85 - x 180 , CR 10 - 85 - y 90 , CR 10 - 85 - y 270 , CR 10 - 85 - X 0.59 0.64 0.69 Y 0.30 0.35 0.40 X 0.29 0.34 0.39 0.57 0.62 0.67 0.09 0.14 0.19 Y 0.04 0.09 0.14 X 0.27 0.32 0.37 Y 0.29 0.34 0.39 X Remarks 2 450 Chromaticity Unit 360 0 , 0 , 0 , CR 10 Y White Typ. x Color Blue Min. 0 , 0 Note 1 Note 1: The brightness is measured from the panel center point, P5 in Fig. 6.2, for the typical value. Note 2: The brightness uniformity is calculated by the equation as below: Brightness uniformity Min. Brightness 100% Max. Brightness , which is based on the brightness values of the 9 points measured by BM-5 as shown in Fig. 6.2. Photo Detector: BM-5 1 2 3 4 5 6 7 8 9 50% 15% 85% Field: 1 Distance: 500 mm 15% 50% LCD panel 85% measuring points Fig. 6.1 KAOHSIUNG HITACHI ELECTRONICS CO., LTD. Fig. 6.2 SHEET NO. 7B64PS 2706-TX15D02VM0CAA-1 PAGE 6-1/2 Note 3: The Contrast Ratio is measured from the center point of the panel, P5, and defined as the following equation: CR Brightness of White Brightness of Black Brightness Note 4: The definition of response time is shown in Fig. 6.3. The rising time is the period from 10% brightness to 90% brightness when the data is from black to white. Oppositely, Falling time is the period from 90% brightness rising to 10% brightness. Fig 6.3 Note 5: The definition of viewing angle is shown in Fig. 6.4. Angle is used to represent viewing directions, for instance, 270 means 6 o'clock, and 0 means 3 o'clock. Moreover, angle is used to represent viewing angles from axis Z toward plane XY. The display is super wide viewing angle version, so that the best optical performance can be obtained from every viewing direction. z = Viewing angle 90 12 o'clock y (x, y ,0) x 0 3 o'clock x' 180 9 o'clock y' 270 z' 6 o'clock Fig 6.4 Note 6: The color chromaticity is measured from the center point of the panel, P5, as shown in Fig. 6.2. KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2706-TX15D02VM0CAA-1 PAGE 6-2/2 7. BLOCK DIAGRAM (1,1) VDD (1,1200) Power Circuit Gate Driver CN1 Gamma Voltage Generator WQVGA LCD Panel (240,1) (240,1200) Source Driver Signals Dim CN2 VLED LED Control Circuit LED Backlight Note1: Signals are DCLK, DE, and RGB data bus KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2707-TX15D02VM0CAA-1 PAGE 7-1/1 8. RELIABILITY TESTS Test Item Condition High Temperature 1) Operating 2) 80 C 240 hrs Low Temperature 1) Operating 2) -30 C 240 hrs High Temperature 1) Storage 2) 90 C 240 hrs Low Temperature 1) Storage 2) -40 C 240 hrs Heat Cycle 1) Operating 2) -20 C ~70 C 3) 3hrs~1hr~3hrs 240 hrs Thermal Shock 1) Non-Operating 2) -35 C 85 C 3) 0.5 hr 0.5 hr 240 hrs High Temperature & Humidity 1) Operating 2) 40 C & 85%RH 3) Without condensation 4) Note 3 240 hrs Vibration 1) Non-Operating 2) 20~200 Hz 3) 3G 4) X, Y, and Z directions 1 hr for each direction 1) Non-Operating 2) 10 ms 3) 50G 4) X, Y and Z directions Once for each direction Mechanical Shock ESD 1) Operating 2) Tip: 200 pF, 250 3) Air discharge for glass: 8KV 4) Contact discharge for metal frame: 8KV 1) Glass: 9 points 2) Metal frame: 8 points 3) Connector: all pins Note 1: Display functionalities are inspected under the conditions defined in the specification after the reliability tests. Note 2: The display is not guaranteed for use in corrosive gas environments. Note 3: Under the condition of high temperature & humidity, if the temperature is higher than 40 C , the humidity needs to be reduced as Fig. 8.1 shown. Relative Humidity RH (%) Note 4: All pins of LCD interface(CN1) have been tested by 100V contact discharge of ESD under non-operating condition. 90 80 70 60 50 40 30 20 10 0 20 25 30 35 40 45 50 55 60 65 70 75 Temperature Ta ( C) Fig. 8.1 KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2708-TX15D02VM0CAA-1 PAGE 8-1/1 9. LCD INTERFACE 9.1 INTERFACE PIN CONNECTIONS The display interface connector (CN1) is FA5S040HP1R3000(JAE), and Pin assignment is as below: Pin No. 1 Symbol VDD 2 Signal Supply voltage Pin No. Symbol Signal 21 G4 Green data 22 G3 Green data 23 24 VSS G2 25 G1 Ground Green data Green data Green data (LSB) 3 4 SD 5 NC Normal Scan: Low (Default) Reverse Scan : High No Connection 6 DE Data Enable 26 G0 7 VSS Ground 27 VSS 8 DCLK Dot clock 28 R5 Red data (MSB) 9 VSS Ground 29 R4 Red data 10 NC No Connection 30 R3 Red data 11 VSS Ground 31 VSS 12 B5 Blue data (MSB) 32 R2 Red data 13 B4 Blue data 33 R1 Red data 14 B3 Blue data 34 R0 Red data (LSB) 15 VSS Ground 35 VSS Ground 16 B2 Blue data 36 DIM Note A 17 B1 Blue data 37 NC No Connection 18 B0 Blue data (LSB) 38 NC No Connection 19 VSS Ground 39 NC No Connection 20 G5 Green data (MSB) 40 NC No Connection Ground Ground Note A: Normal brightness: 0V or 0% PWM duty; Brightness control: 0V to 3.3 V DC or 0% to 100% PWM duty. The backlight connector (CN2) is BHR-03VS-1 made by JST, and pin assignment is as below: Pin No. Symbol 1 VLED 12VDC 2 GND Ground KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. Signal 7B64PS 2709-TX15D02VM0CAA-1 PAGE 9-1/6 9.2 TIMING CHART th = 580 CLK (1H) DE 1 2 3 80 81 580 1 480 DCLK 2 9.0M Hz (typ.) 80 CLK (typ.) thd = 400 CLK (fixed) 100CLK (typ.) Invalid data Display data Invalid data R [0:5] R R R R R R R R R G [0:5] G G G G G G G G G B [0:5] B B B B B B B B B Fig. 9.3 Horizontal Timing Fig. 9.4 Vertical Timing KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2709-TX15D02VM0CAA-1 PAGE 9-2/6 9.3 CLOCK AND DATA INPUT TIMING Tcph DCLK 1st Tcwh 2nd Tdsu Tdhd 70% Data 1st RGB 70% 30% 30% Tcwl Last Data 400 RGB 2nd RGB 30% Tesu DE Tehd 70% 70% Fig. 9.5 Setup & Hold Time of Data and DE signal. KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2709-TX15D02VM0CAA-1 PAGE 9-3/6 9.4 TIME TABLE The column of timing sets including minimum, typical, and maximum as below are based on the best optical performance, frame frequency (Vsync) = 60 Hz to define. If 60 Hz is not the aim to set, 50~70 Hz for Vsync is recommended to apply for better performance by other parameter combination as the definitions in section 5.1. FOR TIMING CHART Item Symbol Min. Typ. Max. Unit CLK Frequency fclk 7.5 9.0 14.4 M Hz Display Data thd 400 400 400 Cycle Time th 500 580 800 Display Data Cycle Time tvd 240 240 240 tv 250 260 300 Symbol Min. Typ. Max. Unit Duty Tcwh 45 50 55 % Cycle Time Tcph 69 111 - Setup Time Tdsu 8 - - Hold Time Tdhd 8 - - Setup Time Tesu 8 - - Hold Time Tehd 8 - - Horizontal Vertical CLK H FOR CLOCK AND DATA INPUT TIMING Item DCLK Data DE KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2709-TX15D02VM0CAA-1 ns PAGE 9-4/6 9.5 POWER SEQUENCE Note 1 VDD 0.7VDD Signals 0.3VDD Backlight 0.3VLED Note 2 Fig. 9.7 Power Sequence Timing Note 1: In order to avoid any damages, VDD has to be applied before all other signals. The opposite is true for power Off where VDD has to be remained on until all other signals have been switch off. The recommended time period is 1 second. Hot plugging might cause display damage due to incorrect power sequence, please pay attention on interface connecting before power on. Note 2: In order to avoid showing uncompleted patterns in transient state. It is recommended that switching the backlight on is delayed for 1 second after the signals have been applied. The opposite is true for power Off where the backlight has to be switched off 1 second before the signals are removed. 9.5 SCAN DIRECTION Scan direction is available to be switched as below by setting CN1's SD pin. Fig. 9.8 Normal Scan (SD: Low ) KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. Fig. 9.9 Reverse Scan(SD: High) 7B64PS 2709-TX15D02VM0CAA-1 PAGE 9-5/6 9.6 DATA INPUT for DISPLAY COLOR Data Signal COLOR & Gray Scale Basic Color Red Green Blue Black Red (0) Green (0) Blue (0) Cyan Magenta Yellow White Black Red (62) Red (61) : : Red (1) Red (0) Black Green (62) Green (61) : : Green (1) Green (0) Black Blue (62) Blue (61) : : Blue (1) Blue (0) KAOHSIUNG HITACHI ELECTRONICS CO., LTD. R5 R4 R3 R2 R1 R0 G5 G4 G3 G2 G1 G0 B5 B4 B3 B2 B1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : : 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 SHEET NO. 7B64PS 2709-TX15D02VM0CAA-1 PAGE B0 0 0 0 1 1 1 0 1 0 0 0 : : 0 0 0 0 0 : : 0 0 0 1 0 : : 0 1 9-6/6 11. APPEARANCE STANDARD The appearance inspection is performed in a dark room around 500~1000 lx based on the conditions as below: - The distance between inspector's eyes and display is 30 cm. - The viewing zone is defined with angle shown in Fig. 11.1 The inspection should be performed within 45 when display is shut down. The inspection should be performed within 5 when display is power on. Fig. 11.1 11.1 THE DEFINITION OF LCD ZONE LCD panel is divided into 3 areas as shown in Fig.11.2 for appearance specification in next section. A zone is the LCD active area (dot area); B zone is the area, which extended 1 mm out from LCD active area; C zone is the area between B zone and metal frame. In terms of housing design, B zone is the recommended window area customers' housing should be located in. Metal frame 1 mm A zone B zone C zone Fig. 11.2 KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2711-TX15D02VM0CAA-1 PAGE 11-1/3 11.2 LCD APPEARANCE SPECIFICATION The specification as below is defined as the amount of unexpected phenomenon or material in different zones of LCD panel. The definitions of length, width and average diameter using in the table are shown in Fig. 11.3 and Fig. 11.4. Item Criteria Length (mm) Ignored L40 L20 Scratches Dent Wrinkles in polarizer Bubbles on polarizer 1) Stains 2) Foreign Materials 3) Dark Spot Dot-Defect (Note 1) Applied zone Width (mm) Maximum number Minimum space W0.02 Ignored 0.02W0.04 10 W0.04 10 Serious one is not allowed Serious one is not allowed Average diameter (mm) Maximum number D0.3 Ignored 0.3D0.5 12 0.5D 3 Filamentous (Line shape) Length (mm) Width (mm) Maximum number L2.0 W0.03 Ignored L3.0 0.03W0.05 10 L2.5 0.05W0.1 1 Round (Dot shape) Average diameter (mm) Maximum number Minimum Space D0.2 Ignored 0.2D0.3 10 10 mm 0.3D0.4 5 30 mm 0.4D None In total Filamentous + Round=10 Those wiped out easily are acceptable Type Maximum number 1 dot 4 2 adjacent dot 1 Bright dot-defect 3 adjacent dot or above Not allowed In total 5 1 dot 5 2 adjacent dot 2 Dark dot-defect 3 adjacent dot or above Not allowed In total 5 In total 10 A, B A A A A, B A, B A a Width Length Fig. 11.3 KAOHSIUNG HITACHI ELECTRONICS CO., LTD. b Average diameter = ab 2 Fig. 11.4 SHEET NO. 7B64PS 2711-TX15D02VM0CAA-1 PAGE 11-2/3 Note 1: The definitions of dot defect are as below: - The defect area of the dot must be bigger than half of a dot. - For bright dot-defect, showing black pattern, the dot's brightness must be over 30% brighter than others. - For dark dot-defect, showing white pattern, the dot's brightness must be under 70% darker than others. - The definition of 1-dot-defect is the defect-dot, which is isolated and no adjacent defect-dot. - The definition of adjacent dot is shown as Fig. 11.5. The dots colored gray are adjacent to defect-dot A. A Fig. 11.5 KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2711-TX15D02VM0CAA-1 PAGE 11-3/3 12. PRECAUTIONS 12.1 PRECAUTIONS of ESD 1) Before handling the display, please ensure your body has been connected to ground to avoid any damages by ESD. Also, do not touch display's interface directly when assembling. 1) Please remove the protection film very slowly before turning on the display to avoid generating ESD. 12.2 PRECAUTIONS of HANDLING 1) In order to keep the appearance of display in good condition, please do not rub any surfaces of the displays by using sharp tools harder than 3H, especially touch panel, metal frame and polarizer. 2) Please do not stack the displays as this may damage the surface. In order to avoid any injuries, please avoid touching the edge of the glass or metal frame and wore gloves during handling. 2) Touching the polarizer or terminal pins with bare hand should be avoided to prevent staining and poor electrical contact. 3) Do not use any harmful chemicals such as acetone, toluene, and isopropyl alcohol to clean display's surfaces. 4) Please use soft cloth or absorbent cotton with ethanol to clean the display by gently wiping. Moreover, when wiping the display, please wipe it by horizontal or vertical direction instead of circling to prevent leaving scars on the display's surface, especially polarizer. 5) Please wipe any unknown liquids immediately such as saliva, water or dew on the display to avoid color fading or any permanent damages. 6) Maximum pressure to the surface of the display must be less than 1.96 x 10 4 Pa. If the area of applied pressure is less than 1 cm 2 , the maximum pressure must be less than 1.96N. KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2712-TX15D02VM0CAA-1 PAGE 12-1/2 12.3 PRECAUTIONS OF OPERATING 1) Please input signals and voltages to the displays according to the values defined in the section of electrical characteristics to obtain the best performance. Any voltages over than absolute maximum rating will cause permanent damages to this display. Also, any timing of the signals out of this specification would cause unexpected performance. 2) When the display is operating at significant low temperature, the response time will be slower than it at 25 C . In high temperature, the color will be slightly dark and blue compared to original pattern. However, these are temperature-related phenomenon of LCD and it will not cause permanent damages to the display when used within the operating temperature. 3) The use of screen saver or sleep mode is recommended when static images are likely for long periods of time. This is to avoid the possibility of image sticking. 4) Spike noise can cause malfunction of the circuit. The recommended limitation of spike noise is no bigger than 100 mV. 12.4 PRECAUTIONS of STORAGE If the displays are going to be stored for years, please be aware the following notices. 1) Please store the displays in a dark room to avoid any damages from sunlight and other sources of UV light. 2) The recommended long term storage temperature is between 10 C ~35 C and 55%~75% humidity to avoid causing bubbles between polarizer and LCD glasses, and polarizer peeling from LCD glasses. 3) It would be better to keep the displays in the container, which is shipped from Hitachi, and do not unpack it. 4) Please do not stick any labels on the display surface for a long time, especially on the polarizer. KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2712-TX15D02VM0CAA-1 PAGE 12-2/2 13. DESIGNATION of LOT MARK 1) The lot mark is showing in Fig.13.1. First 4 digits are used to represent production lot, T represented made in Taiwan, and the last 6 digits are the serial number. 9 0 4 4 T 5 0 1 6 8 8 Serial number T: Made in Taiwan Week Month Year Fig. 13.1 2) The tables as below are showing what the first 4 digits of lot mark are shorted for. Year 2009 2010 2011 2012 2013 Lot Mark 9 0 1 2 3 Month Jan. Feb. Mar. Apr. May Jun. Lot Mark 01 02 03 04 05 06 Month Jul. Aug. Sep. Oct. Nov. Dec. Lot Mark 07 08 09 10 11 12 Week 1~7 days 8~14 days 15~21 days 22~28 days 29~31 days Lot Mark 1 2 3 4 5 3) Except letters I and O, revision number will be shown on lot mark and following letters A to Z. 4) The location of the lot mark is on the back of the display shown in Fig. 13.2. REV:A TX15D02VM0CAA 123456 1041T (5D) HITACHI MADE IN TAIWAN Fig. 13.2 KAOHSIUNG HITACHI ELECTRONICS CO., LTD. SHEET NO. 7B64PS 2713-TX15D02VM0CAA-1 PAGE 13-1/1