DOCUMENT NUMBER SAP-8 Series Single-Mode FC CONNECTOR PLUG TECHNICAL SPECIFICATIONS Seiko Instruments Inc. Components Headquarters. 8, Nakase 1-Chome Mihama-ku, Chiba-shi, Chiba-ken 261-8507 JAPAN Telephone : 043-211-1211 Facsimile : 043-211-8030 NCD-4oB8-05 SAP-8 Series Single-Mode FC CONNECTOR PLUG TECHNICAL SPECIFICATIONS Document Number NCD-4oB8-05 First Edition Second Edition Third Edition Fourth Edition Fifth Edition October 1994 January 1995 January 1996 June 1997 May 1998 Copyright 1994.1995.1996.1997.1998 by Seiko Instruments Inc. All right reserved. The information contained herein shall not reproduced or disclosed to any third party without the express written consent of SII. The Specifications contained herein are subject to change without notice. SII is a trademark of Seiko Instruments Inc. Please address any questions, comments, and suggestions to: Seiko Instruments USA Inc. Seiko Instruments GmbH Seiko Instruments (H.K.) Ltd. Seiko Instruments Taiwan Inc. Electronics Components Division 2990 West Lomita Boulevard Torrance, CA 90505, U.S.A. Phone: 310-517-7780 Fax: 310-517-7792 Sales Department 4th & 5th Floor, Wyler Center 2 200 Tai Lin Pai Road, Kwai Chung N.T., Kowloon, Hong Kong Phone: 852-2421-8611 Fax: 852-2480-5479 OFC Division Siemensstrae 9b D-63263 Neu-Isenburg, Germany Phone: 06102-297-0 Fax: 06102-297-211 Sales Department 5F-1, No.99, Sec. 2, Chung Shan Rd. Taipei 104, Taiwan, R.O.C. Phone: 02-563-5001, 523-5111 Fax: 02-521-9519 Seiko Instruments Singapore pte. Ltd. 2, Marsiling Lane, Woodlands New Town, Singapore, 2573, Singapore Phone: 65-2691370 Fax: 65-2699729 ii TABLE OF CONTENTS Section 1. PROVISION 1.1. Application limit 2. PARTS NUMBER 3. GENERAL SPECIFICATIONS 3.1. Parts and Materials 3.2. Physical Dimensions 3.3. General Tolerances 4. PACKING Page 1 1 1 2 2 2 2 2 Table Table 1 Table 2 Table 3 Table 4 Parts number Parts and materials Parts and materials (Mainbody) General tolerance 1 2 2 2 Figure Figure 1 SAP-8 Connector (Cord type) Figure 2 SAP-8 Connector ( Buffered fiber type) Figure 3 Mainbody Figure 4 to 10 Part dimensions iii 3 4 5 6 iv 1. PROVISION 1.1 Application Limit These specifications apply to the SAP-8 Single-Mode FC CONNECTOR PLUG supplied by SII. 2. PARTS NUMBER Parts number of the connector is shown in Table 1. Table 1 MODEL Number SAP-8 1 3 5 0 1 3 6 9 Parts number TYPE Number 3 3 1 2 5 1 1 3 0 Hood color Black White Blue ( Requied ) 00 Hood Inner Dia without hood 0.9mm (non flamable) 3.0mm (Plastic) 2.0mm (Plastic) 0.9mm (Plastic) Ferrule Inner Dia S5 to S6 ( 0.125 to 0.126mm ) 0 1 3 Package Individual Bulk 1 Marking of Hood 0 1 1 without SII Marking Cap Black Applicable Hood (mm) 0.9mm (non flamable) 0.9 to 3.0mm (Plastic) 3. GENERAL SPECIFICATIONS 3.1 Parts and Materials Parts and the materials are shown in Table 2 to 3. Table 2 No. Part Name 1 Mainbody 2 Crimping ring 3 Crimping ring 4 Hood (3.0mm) 5 Hood (2.0mm) 6 Hood (0.9mm) 7 Hood (0.9mm) 16 Cap Q'ty 1 (1) (1) (1) (1) (1) (1) 1 Material See Table 3 Aluminum alloy Aluminum alloy Plastics Plastics Synthetic rubber Plastics PVC Table 3 No. Part Name 8 Ferrule 9 Flange 10 Frame 11 Key-ring 12 Spring 13 Coupling nut 14 Washer 15 Stopper Q'ty 1 1 1 1 1 1 1 1 Parts and materials Notes Sub-assembled for 3.0mm cable for 2.0mm cable UL94V-0, Hood color shows Table 1 UL94V-0, Hood color shows Table 1 UL94V-0, Hood color shows Table 1 UL94V-0, Hood color shows Table 1 Black Parts and materials ( Mainbody ) Material Zirconia Stainless steel Stainless steel Beryllium copper Stainless steel Brass Phosphor bronze Brass Nickel plating Nickel plating Nickel plating Notes -- -- -- -- -- 3.2 Physical Dimensions Figure 1 shows the assembled state of SAP-8 ( Cord type ). Figure 2 shows the assembled state of SAP-8 ( Buffered fiber type ). Figure 3 shows the Mainbody. Figure 4 to 10 show the part dimension. *In accordance with JIS C 5970 F01 type connectors 3.3 General Tolerance Permissible deviation in dimensions without tolerance indication is in accordance with JIS B 0405 class m, as shown in Table 4. Table 4 General tolerance (JIS B 0405 class m) Basic size step (mm) Over Under 0.5 3 3 6 6 30 30 120 Permissible deviation (mm) 0.1 0.1 0.2 0.3 4. PACKING The product is packed to prevent damage during shipment. 2 note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not assembled like this. note.2: This drawing does not include caps. Figure 1 SAP-8 Connector ( Cord type ) 3 Unit: mm note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not assembled like this. note.2: This drawing does not include caps. Figure 2 SAP-8 Connector ( Buffered fiber type ) 4 Unit: mm note.1: note.2: End curve offset = 0.05mm or less. Ferrule hole diameter shows Table 1. Figure 3 #1 : Mainbody 5 Unit: mm Figure 4 #2 : Crimping ring ( for 3.0mm cord ) Figure 5 #3 : Crimping ring ( for 2.0mm cord ) Figure 6 Figure 7 #4 : Hood ( for 3.0mm cord ) #5 : Hood ( for 2.0mm cord ) 6 Unit: mm Unit: mm Unit: mm Unit: mm Figure 8 #6 : Hood ( for 0.9mm buffered fiber ) Figure 9 #7 : Hood ( for 0.9mm buffered fiber ) Figure 10 #16 : Cap 7 Unit: mm Unit: mm Unit: mm