SAP-81112501100 - Seiko Instruments USA, Inc.

DOCUMENT NUMBER NCD-4oB8-05

SAP-8 Series

Single-Mode

FC CONNECTOR PLUG

TECHNICAL SPECIFICATIONS

Seiko Instruments Inc.

Components Headquarters.

8, Nakase 1-Chome

Mihama-ku, Chiba-shi, Chiba-ken

261-8507 JAPAN

Telephone : 043-211-1211

Facsimile : 043-211-8030

SAP-8 Series Single-Mode FC CONNECTOR PLUG

TECHNICAL SPECIFICATIONS

Document Number NCD-4oB8-05

First Edition October 1994

Second Edition January 1995

Third Edition January 1996

Fourth Edition June 1997

Fifth Edition May 1998

The information contained herein shall not reproduced or disclosed to any third party

without the express written consent of SII.

The Specifications contained herein are subject to change without notice.

SII is a trademark of Seiko Instruments Inc.

Please address any questions, comments, and suggestions to:

Seiko Instruments USA Inc.

Electronics Components Division

2990 West Lomita Boulevard

Torrance, CA 90505, U.S.A.

Phone: 310-517-7780

Fax: 310-517-7792

Seiko Instruments GmbH

OFC Division

Siemensstraβe 9b

D-63263 Neu-Isenburg, Germany

Phone: 06102-297-0

Fax: 06102-297-211

Seiko Instruments (H.K.) Ltd.

Sales Department

4th & 5th Floor, Wyler Center 2

200 Tai Lin Pai Road, Kwai Chung

N.T., Kowloon, Hong Kong

Phone: 852-2421-8611

Fax: 852-2480-5479

Seiko Instruments Taiwan Inc.

Sales Department

5F-1, No.99, Sec. 2, Chung Shan

Rd.

Taipei 104, Taiwan, R.O.C.

Phone: 02-563-5001, 523-5111

Fax: 02-521-9519

Seiko Instruments Singapore pte. Ltd.

2, Marsiling Lane,

Woodlands New Town,

Singapore, 2573, Singapore

Phone: 65-2691370

Fax: 65-2699729

iii

TABLE OF CONTENTS

Section Page

1. PROVISION 1

1.1. Application limit 1

2. PARTS NUMBER 1

3. GENERAL SPECIFICATIONS 2

3.1. Parts and Materials 2

3.2. Physical Dimensions 2

3.3. General Tolerances 2

4. PACKING 2

Table

Table 1 Parts number 1

Table 2 Parts and materials 2

Table 3 Parts and materials (Mainbody) 2

Table 4 General tolerance 2

Figure

Figure 1 SAP-8 Connector (Cord type) 3

Figure 2 SAP-8 Connector ( Buffered fiber type) 4

Figure 3 Mainbody 5

Figure 4 to 10 Part dimensions 6

1. PROVISION

1.1 Application Limit

These specifications apply to the SAP-8 Single-Mode FC CONNECTOR PLUG supplied

by SII.

2. PARTS NUMBER

Parts number of the connector is shown in Table 1.

Table 1 Parts number

MODEL Number TYPE Number

SAP-8 3312511300

Hood color

1 Black ( Requied )

3 White 0 0

5Blue

Package

Hood Inner Dia 1 Individual

0 without hood 3 Bulk

1 0.9mm (non flamable)

3 3.0mm (Plastic) Cap

6 2.0mm (Plastic) 1 Black

9 0.9mm (Plastic)

Marking of Hood

Ferrule Inner Dia Applicable Hood (mm)

S5 to S6 0 without 0.9mm (non flamable)

( 0.125 to 0.126mm ) 1 SII Marking 0.9 to 3.0mm (Plastic)

3. GENERAL SPECIFICATIONS

3.1 Parts and Materials

Parts and the materials are shown in Table 2 to 3.

Table 2 Parts and materials

No. Part Name Q'ty Material Notes

1Mainbody 1See Table 3 Sub-assembled

2Crimping ring ( 1 ) Aluminum alloy for φ3.0mm cable

3Crimping ring ( 1 ) Aluminum alloy for φ2.0mm cable

4Hood (φ3.0mm) ( 1 ) Plastics UL94V-0, Hood color shows Table 1

5Hood (φ2.0mm) ( 1 ) Plastics UL94V-0, Hood color shows Table 1

6Hood (φ0.9mm) ( 1 ) Synthetic rubber UL94V-0, Hood color shows Table 1

7Hood (φ0.9mm) ( 1 ) Plastics UL94V-0, Hood color shows Table 1

16 Cap 1PVC Black

Table 3 Parts and materials ( Mainbody )

No. Part Name Q'ty Material Notes

8 Ferrule 1Zirconia − −

9 Flange 1Stainless steel − −

10 Frame 1Stainless steel − −

11 Key-ring 1Beryllium copper − −

12 Spring 1Stainless steel − −

13 Coupling nut 1Brass Nickel plating

14 Washer 1Phosphor bronze Nickel plating

15 Stopper 1Brass Nickel plating

3.2 Physical Dimensions

Figure 1 shows the assembled state of SAP-8 ( Cord type ).

Figure 2 shows the assembled state of SAP-8 ( Buffered fiber type ).

Figure 3 shows the Mainbody.

Figure 4 to 10 show the part dimension.

•In accordance with JIS C 5970 F01 type connectors

3.3 General Tolerance

Permissible deviation in dimensions without tolerance indication is in accordance with JIS

B 0405 class m, as shown in Table 4.

Table 4 General tolerance (JIS B 0405 class m)

Basic size step (mm)

Over Under

Permissible deviation (mm)

0.5 3 ±0.1

36 ±0.1

630 ±0.2

30 120 ±0.3

4. PACKING

The product is packed to prevent damage during shipment.

note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not

assembled like this.

note.2: This drawing does not include caps.

Unit: mm

Figure 1 SAP-8 Connector ( Cord type )

note.1: This drawing shows the tentatively assembled condition. In practice, the connector plug is not

assembled like this.

note.2: This drawing does not include caps.

Unit: mm

Figure 2 SAP-8 Connector ( Buffered fiber type )

note.1: End curve offset = 0.05mm or less.

note.2: Ferrule hole diameter shows Table 1.

Unit: mm

Figure 3 #1 : Mainbody

Unit: mm

Figure 4 #2 : Crimping ring ( for 3.0mm cord )

Unit: mm

Figure 5 #3 : Crimping ring ( for 2.0mm cord )

Unit: mm

Figure 6 #4 : Hood ( for 3.0mm cord )

Unit: mm

Figure 7 #5 : Hood ( for 2.0mm cord )

Unit: mm

Figure 8 #6 : Hood ( for 0.9mm buffered fiber )

Unit: mm

Figure 9 #7 : Hood ( for 0.9mm buffered fiber )

Unit: mm

Figure 10 #16 : Cap