KH205 Overdrive-Protected Wideband Op Amp Features n n n n n n n General Description -3dB bandwidth of 170MHz 0.1% settling in 22ns Complete overdrive protection Low power: 570mW (190mW at 5V) 3M input resistance Output may be current limited Direct replacement for CLC205 Applications n n n n n n Fast, precision A/D conversion Automatic test equipment Input/output amplifiers Photodiode, CCD preamps IF processors High-speed modems, radios Line drivers For example, the KH205 has been designed to consume little power - 570mW at 15V supplies. The result is lower power supply requirements and less systemlevel heat dissipation. In addition, the device can be operated on supply voltages as low as 5V for even lower power dissipation. Complete overdrive protection has been designed into the part. This is critical for applications, such as ATE and instrumentation, which require protection from signal levels high enough to cause saturation of the amplifier. This feature allows the output of the op amp to be protected against short circuits using techniques developed for low-speed op amps. With this capability, even the fastest signal sources can feature effective short circuit protection. Large Signal Pulse Response Av = +20 Output Voltage (2V/div) n The KH205 is constructed using thin film resistor/bipolar transistor technology, and is available in the following versions: Av = -20 Time (5ns/div) Bottom View 2 Internal Feedback Case ground GND 7 Rf -VCC 8 9 10 V+ 6 Inverting Input V- 5 Not Connected NC 4 Case and bias ground Supply Voltage -VCC 2000 Non-Inverting Input The KH205 is a wideband overdrive-protected operational amplifier designed for applications needing both speed and low power operation. Utilizing a well-established current feedback architecture, the KH205 exhibits performance far beyond that of conventional voltage feedback op amps. For example, the KH205 has a bandwidth of 170MHz at a gain of +20 and settles to 0.1% in 22ns. Plus, the KH205 has a combination of important features not found in other high-speed op amps. + 6 - 6 3 2 1 GND NC +VCC -25C to +85C -55C to +125C KH205AM -55C to +125C KH205HXC KH205HXA -55C to +125C -55C to +125C Collector Supply 11 Vo Output 12 Collector Supply +VCC KH205AI KH205AK Typical Performance Gain Setting Supply Voltage Not Connected Pin 8 provides access to a 2000 feedback resistor which can be connected to the output or left open if an external feedback resistor is desired. 12-pin TO-8 can 12-pin TO-8 can, features burn-in & hermetic testing 12-pin TO-8 can, environmentally screened and electrically tested to MIL-STD-883 SMD#: 5962-9083501HXC SMD#: 5962-9083501HXA Parameter -20 -50 Units -3dB bandwidth 220 170 80 220 130 80 rise time 1.7 2.2 4.7 1.7 2.9 4.7 slew rate 2.4 2.4 2.4 2.4 2.4 2.4 settling time (to 0.1%) 22 22 20 21 20 19 MHz ns V/ns ns +7 +20 +50 -1 REV. 1A January 2004 DATA SHEET KH205 KH205 Electrical Characteristics (Av = +20V, VCC = 15V, RL = 200, Rf = 2k; unless specified) PARAMETERS CONDITIONS Ambient Temperature KH205AI +25C -55C +25C +125C Ambient Temperature KH205AK/AM/HXC/HXA +25C -55C +25C +125C FREQUENCY DOMAIN RESPONSE = -3dB bandwidth large-signal bandwidth gain flatness = peaking = peaking = rolloff group delay linear phase deviation Vo = <2Vpp Vo = <10Vpp Vo = <2Vpp 0.1 to 35MHz >35MHz at 70MHz to 70MHz to 70MHz 170 100 >140 >72 >140 >80 0 0 - 3.0 .2 0.8 <0.3 <0.5 <0.8 - <3.0 2V step 10V step 10V step, note 2 10V step, note 2 5V step 20Vpp at 50MHz 2.2 4.8 22 24 7 2.4 2Vpp, 20MHz 2Vpp, 20MHz >100kHz >100kHz >100kHz >100kHz 1kHz to 150MHz >5MHz 5MHz to 150MHz TIME DOMAIN RESPONSE rise and fall time settling time to 0.1% to 0.05% overshoot slew rate NOISE AND DISTORTION RESPONSE = 2nd harmonic distortion = 3rd harmonic distortion equivalent input noise voltage inverting current non-inverting current noise floor integrated noise noise floor integrated noise STATIC, DC PERFORMANCE * input offset voltage average temperature coefficient * input bias current average temperature coefficient * input bias current average temperature coefficient * power supply rejection ratio common mode rejection ratio * supply current MISCELLANEOUS PERFORMANCE non-inverting input resistance non-inverting input capacitance output impedance output voltage range internal feedback resistor absolute tolerance temperature coefficient inverting input current self limit UNITS SYM >125 >80 MHz MHz SSBW FPBW <0.3 <0.5 <0.8 - <2.0 <0.5 <0.8 <0.8 - <3.0 dB dB dB ns GFPL GFPH GFR GD LPD <2.6 <5.5 <27 <30 <14 >1.8 <2.6 <5.5 <27 <30 <14 >2.0 <3.0 <5.5 <27 <30 <14 >2.0 ns ns ns ns % V/ns TRS TRL TS TSP OS SR -57 -68 <-50 <-55 <-50 <-55 <-50 <-55 dBc dBc HD2 HD3 2.1 22 4.8 -157 39 -157 39 <3.0 <30 <6.5 <-154 <55 <-154 <55 <3.0 <30 <6.5 <-154 <55 <-154 <55 <3.5 <35 <7.5 <-153 <61 <-153 <61 nV/Hz pA/Hz pA/Hz dBm(1Hz) V dBm(1Hz) V VN ICN NCN SNF INV SNF INV no load 3.5 11 3.0 15 2.0 20 69 60 19 <8.0 <25 <25 <100 <22 <150 >55 >50 <20 <8.0 <25 <15 <100 <10 <150 >55 >50 <20 <11.0 <25 <15 <100 <25 <150 >55 >50 <22 mV V/C nA/C A nA/C dB dB mA VIO DVIO IBN DIBN IBI DIBI PSRR CMRR ICC DC 70MHz DC no load 3.0 5.0 - 12 >1.0 <7.0 <0.1 >11 >1.0 <7.0 <0.1 >11 >1.0 <7.0 <0.1 >11 M pF V RIN CIN RO VO - - 2.2 - - <3.0 <0.2 -100 40 <3.0 - - <3.2 % ppm/C mA RFA RFTC ICL non-inverting inverting TYP MIN & MAX RATINGS Min/max ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are determined from tested parameters. Absolute Maximum Ratings Recommended Operating Conditions VCC 20V 75mA Io common mode input voltage (|VCC| -1)V differential input voltage 3V thermal resistance (see thermal model) operating temperature AI: -25C to +85C AK/AM/HXC/HXA: -55C to +125C sample tested storage temperature -65C to +150C lead temperature (soldering 10s) +300C VCC Io common mode input voltage gain range note 1: note 2: 2 5V to 15V 50mA (|VCC| -5)V +7 to +50, -1 to -50 * AI/AK/AM/HXC/HXA = AK/AM/HXC/HXA 100% tested at +25C 100% tested at +25C and at -55C and +125C = AI sample tested at +25C Settling time specifications require the use of an external feedback resistor (2) REV. 1A January 2004 KH205 DATA SHEET KH205 Typical Performance Characteristics (TA = +25C, Av = +20, VCC = 15V, RL = 200; unless specified) Normalized Magnitude (1dB/div) Inverting Frequency Response Phase (45/div) Gain Av = +20 Av = +50 Av = +7 Phase Av = +50 Av = +20 0 20 40 60 80 100 120 140 160 180 200 Av = +50 Av = -1 Gain Av = -7 Av = -20 Phase Av = -50 Av = -1 Av = -20 Av = -7 Rf = 3k Rf = 1.5k 20 40 Frequency (MHz) 60 Rf = 3k 0 20 Rf = 2k Rf = 3k 40 60 80 100 120 140 160 180 200 Frequency (MHz) Relative Bandwidth vs. VCC 2 Rf = 1.5k Av = +7 80 100 120 140 160 180 200 Frequency (MHz) Large Signal Gain and Phase Gain and Phase for Various Loads 2 2 1.0 Vo = 10Vpp RL = 50 Magnitude (1dB/div) Phase RL = 100 Gain 0.8 0.7 0.6 0.5 0.4 RL = 200 RL = 1k Phase Phase (45/div) Phase (45/div) Gain Relative Bandwidth 0.9 Magnitude (1dB/div) Rf = 2k Av = +20 Av = -50 0 Rf = 1.5k Rf = 2k Relative Gain (5dB/div) Av = +7 Frequency Response vs. External Rf Phase (45/div) Normalized Magnitude (1dB/div) Non-Inverting Frequency Response RL = 1k RL = 200 RL = 100 RL = 50 0.3 0.2 0 15 30 45 60 75 90 105 120 135 150 4 6 8 10 Small Signal Pulse Response 14 0 16 20 40 Large Signal Pulse Response 2 Av = -20 80 100 120 140 160 180 200 Settling Time 2 2 0.20 10V step Rf = 2k (external) 0.15 Av = +20 Output Voltage (2V/div) Av = +20 60 Frequency (MHz) Settling Error (%) Output Voltage (0.4V/div) 12 VCC (V) Frequency (MHz) 0.10 0.05 0 -0.05 -0.10 -0.15 Av = -20 -0.20 Time (5ns/div) 2nd and 3rd Harmonic Distortion 2 2-Tone 3rd Order Intermodulation Intercept 2 -30 PSRR and CMRR (dB) Vo = 2Vpp -40 40 Intercept (dBm) Distortion (dBc) 2 CMRR and PSRR 100 45 -35 -45 -50 -55 2nd -60 -65 -70 35 30 25 -75 80 PSRR 60 CMRR 40 20 3rd -80 20 1 10 100 0 0 20 Frequency (MHz) Equivalent Input Noise 2 10 Non-Inverting Current 2.5 pA/Hz Voltage 1.8 nV/Hz 0 10k 100k 1M 80 100 0 100M 100 Frequency (Hz) 100 1k 10k 100k 1M 10M 2T 2 case 200C/W Tj(pnp) Ppnp 17.5C/W 200C/W 100M Frequency (Hz) Thermal Model Noise Current (pA/Hz) 10 1k 60 100 Inverting Current 18.3 pA/Hz 100 40 Frequency (MHz) 100 Noise Voltage (nV/Hz) Time (5ns/div) Time (5ns/div) ca Tj(circuit) Tj(npn) Pnpn Pcircuit + Tambient Pcircuit = [(+VCC) - (-VCC)]2 / 1.77k Pxxx = [(VCC) - Vout (% duty cycle) - (Icol) (Rcol + 6)] (Icol) (For positive Vo and VCC, this is the power in the npn output stage.) (For negative Vo and VCC, this is the power in the pnp output stage.) Icol = Vout/Rload or 3mA, whichever is greater. (Include feedback R in Rload.) Rcol is a resistor (33 recommended) between the xxx collector and VCC. Tj (pnp) = Ppnp (200 + ca) + (Pcir + Pnpn)ca + Ta, similar for Tj (npn). Tj (cir) = Pcir (17.5 + ca) + (Ppnp + Pnpn)ca + Ta. 2 REV. 1A January 2004 3 DATA SHEET KH205 Current Feedback Amplifiers Some of the key features of current feedback technology are: n Independence of AC bandwidth and voltage gain n Adjustable frequency response with feedback resistor n High slew rate n Fast settling Short Circuit Protection Damage caused by short circuits at the output may be prevented by limiting the output current to safe levels. The most simple current limit circuit calls for placing resistors between the output stage collector supplies and the output stage collectors (pins 12 and 10). The value of this resistor is determined by: Current feedback operation can be described using a simple equation. The voltage gain for a non-inverting or inverting current feedback amplifier is approximated by Equation 1. V RC = C - RI II Vo Av = Vin 1 + R f Z( j ) where: n n n n where II is the desired limit current and RI is the minimum expected load resistance (0 for a short to ground). Bypass capacitors of 0.01F on should be used on the collectors as in Figures 2 and 3. Equation 1 Av is the closed loop DC voltage gain Rf is the feedback resistor Z(j) is the CLC205's open loop transimpedance gain n n n n 6 5 + Vo Rg common mode protection Figure 1: Diode Clamp Circuits for Common Mode and Differential Mode Protection K 11 - Vo 200 3,7 9 Rf Rg Rf = 2000 (internal) 33 3.9 A v = 1+ .1 .01 33 +15V 3.9 differential protection KH205 8 10 -15V Capactance in F .1 50 6 -Vcc 12 KH205 Figure 2: Recommended Non-Inverting Gain Circuit Overdrive Protection Unlike most other high-speed op amps, the KH205 is not damaged by saturation caused by overdriving input signals (where Vin x gain > max. Vo). The KH205 self limits the current at the inverting input when the output is saturated (see the inverting input current self limit specification); this ensures that the amplifier will not be damaged due to excessive internal currents during overdrive. For protection against input signals which would exceed either the maximum differential or common mode input voltage, the diode clamp circuits below may be used. 4 1 + Rg Decreases loop gain Decreases bandwidth Reduces gain peaking Lowers pulse response overshoot Affects frequency response phase linearity +Vcc .01 Ri 50 Vin Capactance in F .1 Vin Z( j ) is the loop gain Rf The denominator of Equation 1 is approximately equal to 1 at low frequencies. Near the -3dB corner frequency, the interaction between Rf and Z(j) dominates the circuit performance. The value of the feedback resistor has a large affect on the circuits performance. Increasing Rf has the following affects: n 33 +15V 3.9 Rg 5 Vin .01 1 + 12 8 11 KH205 Vo 10 - 200 3,7 9 Ri Av = 33 -15V 3.9 .1 .01 -R f Rg Rf = 2000 (internal) For Zin = 50, select Rg||Ri = 50 Figure 3: Recommended Inverting Gain Circuit A more sophisticated current limit circuit which provides a limit current independent of RI is shown in Figure 4 on page 5. With the component values indicated, current limiting occurs at 50mA. For other values of current limit (II), select RC to equal Vbe/lI. Where Vbe is the base to emitter voltage drop of Q3 (or Q4) at a current of [2VCC - 1.4] / Rx, where Rx [(2VCC - 1.4) / II] Bmin. Also, Bmin is the minimum beta of Q1 (or Q2) at a current of II. Since the limit current depends on Vbe, which is temperature dependent, the limit current is likewise temperature dependent. REV. 1A January 2004 KH205 DATA SHEET +Vcc Rc 12 Q3 (2N3906) Q1 (MJE170) where R p = 0.01F to pin 12 Rx 14.3k to pin 10 0.01F Q2 (MJE180) Q4 (2N3904) Rc 12 -Vcc Figure 4: Active Current Limit Circuit (50mA) Controlling Bandwidth and Passband Response K In most applications, a feedback resistor value of 2k will provide optimum performance; nonetheless, some applications may require a resistor of some other value. The response versus Rf plot on the previous page shows how decreasing Rf will increase bandwidth (and frequency response peaking, which may lead to instability). Conversely, large values of feedback resistance tend to roll off the response. The best settling time performance requires the use of an external feedback resistor (use of the internal resistor results in a 0.1% to 0.2% settling tail). The settling performance may be improved slightly by adding a capacitance of 0.4pF in parallel with the feedback resistor (settling time specifications reflect performance with an external feedback resistor but with no external capacitance). Noise Analysis Approximate noise figure can be determined for the KH205 using the Equivalent Input Noise plot on page 3 and the equations shown below. kT = 4.00 x 10-21 Joules at 290K Vn is spot noise voltage (V/Hz) in is non-inverting spot noise current (A/Hz) ii is inverting spot noise current (A/Hz) Rs + Rn KH205 Rf Rg REV. 1A January 2004 R 2f i i2 Rs R s 2 V n2 F = 10 log 1 + + in + + R n 4 kT R p2 R p2 A 2v Ro Rs Rn Rs +Rn ; Av = Rf Rg +1 Figure 5: Noise Figure Diagram and Equations (Noise Figure is for the Network Inside this Box.) Driving Cables and Capacitive Loads When driving cables, double termination is used to prevent reflections. For capacitive load applications, a small series resistor at the output of the KH205 will improve stability and settling performance. Transmission Line Matching One method for matching the characteristic impedance (Zo) of a transmission line or cable is to place the appropriate resistor at the input or output of the amplifier. Figure 6 shows typical inverting and non-inverting circuit configurations for matching transmission lines. R1 Z0 V1 +- R3 R2 R4 V2 +- Z0 Rg C6 + Z0 KH205 - R6 Vo R7 Rf R5 Figure 6: Transmission Line Matching Non-inverting gain applications: n n n Connect Rg directly to ground. Make R1, R2, R6, and R7 equal to Zo. Use R3 to isolate the amplifier from reactive loading caused by the transmission line, or by parasitics. Inverting gain applications: n n n Connect R3 directly to ground. Make the resistors R4, R6, and R7 equal to Zo. Make R5 II Rg = Zo. The input and output matching resistors attenuate the signal by a factor of 2, therefore additional gain is needed. Use C6 to match the output transmission line over a greater frequency range. C6 compensates for the increase of the amplifier's output impedance with frequency. Dynamic Range (Intermods) For RF applications, the KH205 specifies a third order intercept of 30dBm at 60MHz and Po = 10dBm. A 2-Tone, 3rd Order IMD Intercept plot is found in the Typical Performance Characteristics section. The output power level is taken at the load. Third-order harmonic distortion is calculated with the formula: HD3rd = 2 * (IP3o - Po) 5 DATA SHEET where: n n n n IP3o = third-order output intercept, dBm at the load. Po = output power level, dBm at the load. HD3 rd = third-order distortion from the fundamental, -dBc. dBm is the power in mW, at the load, expressed in dB. Realized third-order output distortion is highly dependent upon the external circuit. Some of the common external circuit choices that improve 3rd order distortion are: n n n n short and equal return paths from the load to the supplies. de-coupling capacitors of the correct value. higher load resistance. a lower ratio of the output swing to the power supply voltage. Printed Circuit Layout As with any high frequency device, a good PCB layout will enhance the performance of the KH205. Good ground plane construction and power supply bypassing close to the package are critical to achieving full performance. In the non-inverting configuration, the amplifier is sensitive to stray capacitance to ground at the inverting input. Hence, the inverting node connections should be small with minimal stray capacitance to the ground plane or other nodes. Shunt capacitance across the feedback resistor should not be used to compensate for this effect. General layout and supply bypassing play major roles in 6 KH205 high frequency performance. Follow the steps below as a basis for high frequency layout: n n n n n n Include 6.8F tantalum and 0.1F ceramic capacitors on both supplies. Place the 6.8F capacitors within 0.75 inches of the power pins. Place the 0.1F capacitors less than 0.1 inches from the power pins. Remove the ground plane under and around the part, especially near the input and output pins to reduce parasitic capacitance. Minimize all trace lengths to reduce series inductances. Use flush-mount printed circuit board pins for prototyping, never use high profile DIP sockets. Evaluation PC boards (part number 730008 for inverting, 730009 for non-inverting) for the KH205 are available to aid in device testing. REV. 1A January 2004 DATA SHEET KH205 KH205 Package Dimensions L A e1 e2 7 D e D1 8 9 6 10 5 11 4 12 k b 3 2 1 F k1 TO-8 SYMBOL INCHES MILIMETERS Minimun Maximum Minimum Maximum A 0.142 0.181 3.61 4.60 b 0.016 0.019 0.41 0.48 D 0.595 0.605 15.11 15.37 D1 0.543 0.555 13.79 14.10 e 0.400 BSC 10.16 BSC e1 0.200 BSC 5.08 BSC e2 0.100 BSC 2.54 BSC F 0.016 0.030 0.41 0.76 k 0.026 0.036 0.66 0.91 k1 0.026 0.036 0.66 0.91 L 0.310 0.340 7.87 8.64 45 BSC 45 BSC NOTES: Seal: cap weld Lead finish: gold per MIL-M-38510 Package composition: Package: metal Lid: Type A per MIL-M-38510 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Exar: KH205AM KH205AI