1999 Apr 29 477
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP RADIAL EPOXY LACQUERED TYPE PITCH 10/15/22.5/27.5 mm
PITCH 7.5 mm (bent back leads)
Fig.1 Simplified outlines.
296x12(full_width)
P = 10 mm P = 15 - 22.5 -27.5 mm
CBA951
P(bent back leads) = 7.5 mm
FEATURES
•10 to 27.5 mm lead pitch
•Supplied loose in box and taped on
reel.
APPLICATIONS
•Low losses due to low contact
resistance and low loss dielectric
result in applications where high
currents at high frequency occur or
high stability is preferred
•Typical for S-correction in TV-sets
and monitor
•Their small dimensions make them
suitable for circuits with high
packaging density.
DETAIL SPECIFICATION
For more detailed data and test
requirements see
“Type detail
specification HQN-384-17/105”
.
QUICK REFERENCE DATA
DESCRIPTION VALUE
Capacitance range (E24 series) 0.002 to 3.9 µF
Capacitance tolerance ±5%
Rated (DC) voltage 160 V; 250 V; 400 V; 630 V; 1000 V;
1250 V;1600 V; 2000 V; 2500 V
Rated (AC) voltage 100 V; 160 V; 200 V; 200 V; 350 V;
440 V; 550 V; 700 V; 900 V
Rated peak-to-peak voltage 280 V; 450 V; 560 V; 560 V; 1000 V;
1250 V; 1600 V; 2000 V; 2500 V
Climatic category 55/105/56
Rated temperature (DC) 85 °C
Rated temperature (AC) 85 °C
Maximum application temperature 105 °C
Reference specification IEC 60384-17
Performance grade grade 1 (long life)
Stability grade grade 2
1999 Apr 29 478
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
COMPOSITION OF CATALOGUE NUMBER
TYPE AND PITCHES
479
15.0/7.5 mm
10.0 mm
15.0 mm
22.5 mm
27.5 mm
TYPE PACKAGING LEAD CONFIGURATION C-TOL 160 V 250 V 250 V 400 V 400 V
monitor
type monitor
type
479
loose in box lead length 5.0 mm ±5% 32 42 41 52 51
lead length 3.5 mm ±5% 34 44 43 54 53
taped on reel H = 16.0 mm;
P0= 12.7 mm ±5% 35 45 47 55 57
taped on reel
(bent back) H = 16.0 mm;
P0= 15.0 mm ±5% 36 46 49 56 59
MULTIPLIER
(nF)
0.1 2
13
10 4
100 5
CAPACITANCE
(numerically)
2222 479 XX XX X
Example:
104 = 10 ×10 = 100 nF
1999 Apr 29 479
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
TYPE AND PITCHES
479
15.0/7.5 mm
10.0 mm
15.0 mm
22.5 mm
27.5 mm
TYPE PACKAGING LEAD CONFIGURATION C-TOL 630 V 1000 V 1250 V 1600 V 2000 V 2500 V
479
loose in box lead length 5.0 mm ±5% 62 72 82 02 12 22
lead length 3.5 mm ±5% 64 74 84 04 14 24
taped on reel H = 16.0 mm; P0= 12.7 mm ±5% 65 75 85 05 15 25
taped on reel
(bent back) H = 16.0 mm; P0= 15.0 mm ±5% 66 76 86 06 16 −
MULTIPLIER
(nF)
0.1 2
13
10 4
100 5
CAPACITANCE
(numerically)
2222 479 XX XX X
Example:
104 = 10 ×10 = 100 nF
1999 Apr 29 480
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 10/15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 160 V DC capacitors
Available 160 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
C=0.075 µF≤5×10−4≤20 ×10−4
0.075 µF<C≤0.11 µF≤5×10−4≤25 ×10−4
0.11 µF<C≤0.18 µF≤10 ×10−4≤30 ×10−4
0.18 µF<C≤0.3 µF≤10 ×10−4≤35 ×10−4
0.3 µF<C≤0.39 µF≤10 ×10−4≤40 ×10−4
0.39 µF<C≤0.56 µF≤10 ×10−4≤45 ×10−4
0.56 µF<C≤0.68 µF≤10 ×10−4≤50 ×10−4
0.68 µF<C≤0.75 µF≤10 ×10−4≤55 ×10−4
Rated voltage pulse slope (dU/dt)R at 160 V (DC):
P=10 mm 60 V/µs
P=15 mm 50 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 256 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 32... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 34... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 35... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 36... preferred
Fig.4 Outline.
handbook, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
1999 Apr 29 481
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =160 V; URac =100 V/Up-p =280 V
Notes
1. Dimensions in brackets for bent back leads
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch = 10.0 and 15.0 mm: H = 16.0 mm and P0= 12.7 mm.
b) For pitch = 15/7.5 mm (bent back): H = 16.0 mm and P0= 15.0 mm.
Standard reel diameter = 500 mm. Small reel diameter = 356 mm is available on request.
3. The shading indicates preferred types.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =10.0 ±0.4 mm; dt=0.60 ±0.06 mm; A =2.0 +1.0/−0.5 mm
0.075
6.0 ×15.0 ×12.5 0.9
2222 479 32753
not available
0.082 2222 479 32823
0.091 2222 479 32913
0.1 2222 479 32104
0.11 2222 479 32114
0.12 2222 479 32124
0.13 2222 479 32134
0.15 6.5 ×15.5 ×12.5 1.0 2222 479 32154
0.16 2222 479 32164
Pitch =15.0 ±0.4 mm (pitch = 7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.18 6.0 ×15.0 (16.5) ×17.5 1.2 2222 479 32184 .. 36184
0.20 6.5 ×15.5 (17.0) ×17.5 1.3 2222 479 32204 .. 36204
0.22 2222 479 32224 .. 36224
0.24
7.0 ×16.0 (17.5) ×17.5 1.4
2222 479 32244 .. 36244
0.27 2222 479 32274 .. 36274
0.30 2222 479 32304 .. 36304
0.33 2222 479 32334 .. 36334
0.36 2222 479 32364 .. 36364
0.39 2222 479 32394 .. 36394
0.43 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 32434 .. 36434
0.47 2222 479 32474 .. 36474
0.51 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 32514 .. 36514
0.56 2222 479 32564 .. 36564
0.62 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 32624 .. 36624
0.68 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 32684 .. 36684
0.75 9.5 ×18.5 (20.0) ×17.5 1.9 2222 479 32754 .. 36754
1999 Apr 29 482
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 160 V DC capacitors
Available 160 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE DESCRIPTION VALUE
at 10 kHz at 100 kHz at 10 kHz at 100 kHz
Tangent of loss angle: Tangent of loss angle:
C=0.82 µF≤10 ×10−4≤55 ×10−41.8 µF<C≤2.0 µF≤10 ×10−4≤95 ×10−4
0.82 µF<C≤0.91 µF≤10 ×10−4≤60 ×10−42.0 µF<C≤2.2 µF≤10 ×10−4≤100 ×10−4
0.91 µF<C≤1.0 µF≤10 ×10−4≤65 ×10−42.2 µF<C≤2.4 µF≤15 ×10−4≤105 ×10−4
1.0 µF<C≤1.2 µF≤10 ×10−4≤70 ×10−42.4 µF<C≤2.7 µF≤15 ×10−4≤110 ×10−4
1.2 µF<C≤1.3 µF≤10 ×10−4≤75 ×10−42.7 µF<C≤3.0 µF≤15 ×10−4≤115 ×10−4
1.3 µF<C≤1.5 µF≤10 ×10−4≤80 ×10−43.0 µF<C≤3.3 µF≤15 ×10−4≤125 ×10−4
1.5 µF<C≤1.6 µF≤10 ×10−4≤85 ×10−43.3 µF<C≤3.6 µF≤15 ×10−4≤130 ×10−4
1.6 µF<C≤1.8 µF≤10 ×10−4≤90 ×10−43.6 µF<C≤3.9 µF≤15 ×10−4≤135 ×10−4
Rated voltage pulse slope
(dU/dt)R at 160 V (DC): Rated voltage pulse slope
(dU/dt)R at 160 V (DC):
P=22.5 mm 25 V/µsP=27.5 mm 15 V/µs
R between leads, for C ≤1µF at 100 V; 1 minute >100000 MΩ
RC between leads, for C >1µF at 100 V; 1 minute >100000 s
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak
discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA);
rise time 100 V/s 256 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 32... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 34... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 35... on request
Fig.5 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
296x12(full_width)
CBA355
P
seating plane(1)
A
h
lt
l
Ødt
b
α
(2)
1999 Apr 29 483
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =160 V; URac =100 V/Up-p =280 V
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.82 7.0 ×20.0 ×26.0 1.8 2222 479 32824
0.91 7.5 ×20.5 ×26.0 1.9 2222 479 32914
1 2222 479 32105
1.1 8.0 ×21.0 ×26.0 2.0 2222 479 32115
1.2 8.5 ×21.5 ×26.0 2.1 2222 479 32125
1.3 2222 479 32135
1.5 9.5 ×22.5 ×26.0 2.4 2222 479 32155
1.6 2222 479 32165
1.8 10.0 ×23.0 ×26.0 2.5 2222 479 32185
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
2 10.0 ×23.0 ×30.0 5.0 2222 479 32205
2.2 10.5 ×23.5 ×30.0 5.0 2222 479 32225
2.4 11.0 ×24.0 ×30.0 5.5 2222 479 32245
2.7 11.5 ×24.5 ×30.0 5.5 2222 479 32275
3 12.0 ×25.0 ×30.0 6.0 2222 479 32305
3.3 13.0 ×26.0 ×30.0 6.5 2222 479 32335
3.6 13.5 ×26.5 ×30.0 7.0 2222 479 32365
3.9 14.0 ×27.0 ×30.0 7.0 2222 479 32395
1999 Apr 29 484
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 10/15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 250 V DC capacitors
Available 250 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.047 µF<C≤0.075 µF≤5×10−4≤20 ×10−4
0.075 µF<C≤0.11 µF≤5×10−4≤25 ×10−4
0.11 µF<C≤0.18 µF≤10 ×10−4≤30 ×10−4
0.18 µF<C≤0.3 µF≤10 ×10−4≤35 ×10−4
0.3 µF<C≤0.39 µF≤10 ×10−4≤40 ×10−4
0.39 µF<C≤0.47 µF≤10 ×10−4≤45 ×10−4
Rated voltage pulse slope (dU/dt)R at 250 V (DC):
P=10.0 mm 70 V/µs
P=15.0 mm 60 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 400 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 42... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 44... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 45... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 46... preferred
Fig.6 Outline.
handbook, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
1999 Apr 29 485
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =250 V; URac =160 V/Up-p =450 V
Notes
1. Dimensions in brackets for bent back leads.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch = 10.0 and 15.0 mm: H = 16.0 mm and P0= 12.7 mm.
b) For pitch = 15/7.5 mm (bent back): H = 16.0 mm and P0= 15.0 mm.
Standard reel diameter = 500 mm. Small reel diameter = 356 mm is available on request.
3. The shading indicates preferred types.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =5%
catalogue number(3) catalogue number(3)
Pitch =10.0 ±0.4 mm; dt=0.60 ±0.06 mm; A =2.0 +1/−0.5 mm
0.047
6.0 ×15.0 ×12.5 0.9
2222 479 42473
not available
0.051 2222 479 42513
0.056 2222 479 42563
0.062 2222 479 42623
0.068 2222 479 42683
0.075 2222 479 42753
0.082 2222 479 42823
0.091 2222 479 42913
0.1 6.5 ×15.5 ×12.5 1.0 2222 479 42104
Pitch =15.0 ±0.4 mm; (pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.11
6.5 ×15.5 (17.0) ×17.5 1.3
2222 479 42114 .. 46114
0.12 2222 479 42124 .. 46124
0.13 2222 479 42134 .. 46134
0.15 2222 479 42154 .. 46154
0.16 2222 479 42164 .. 46164
0.18 2222 479 42184 .. 46184
0.20 2222 479 42204 .. 46204
0.22 2222 479 42224 .. 46224
0.24 7.0 ×16.0 (17.5) ×17.5 1.4 2222 479 42244 .. 46244
0.27 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 42274 .. 46274
0.30 2222 479 42304 .. 46304
0.33 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 42334 .. 46334
0.36 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 42364 .. 46364
0.39 2222 479 42394 .. 46394
0.43 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 42434 .. 46434
0.47 9.5 ×18.5 (20.0) ×17.5 1.9 2222 479 42474 .. 46474
1999 Apr 29 486
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 250 V DC capacitors
Available 250 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE DESCRIPTION VALUE
at 10 kHz at 100 kHz at 10 kHz at 100 kHz
Tangent of loss angle: Tangent of loss angle:
0.51 µF<C≤0.56 µF≤10 ×10−4≤45 ×10−41.3 µF<C≤1.5 µF≤10 ×10−4≤80 ×10−4
0.56 µF<C≤0.68 µF≤10 ×10−4≤50 ×10−41.5 µF<C≤1.6 µF≤10 ×10−4≤85 ×10−4
0.68 µF<C≤0.82 µF≤10 ×10−4≤55 ×10−41.6 µF<C≤1.8 µF≤10 ×10−4≤90 ×10−4
0.82 µF<C≤0.91 µF≤10 ×10−4≤60 ×10−41.8 µF<C≤2.0 µF≤10 ×10−4≤95 ×10−4
0.91 µF<C≤1.0 µF≤10 ×10−4≤65 ×10−42.0 µF<C≤2.2 µF≤10 ×10−4≤100 ×10−4
1.0 µF<C≤1.2 µF≤10 ×10−4≤70 ×10−42.2 µF<C≤2.4 µF≤15 ×10−4≤105 ×10−4
1.2 µF<C≤1.3 µF≤10 ×10−4≤75 ×10−42.4 µF<C≤2.7 µF≤15 ×10−4≤110 ×10−4
2.7 µF<C≤3µF≤15 ×10−4≤115 ×10−4
Rated voltage pulse slope
(dU/dt)R at 250 V (DC): Rated voltage pulse slope
(dU/dt)R at 250 V (DC):
P=22.5 mm 30 V/µsP=27.5 mm 20 V/µs
R between leads, for C ≤1µF at 100 V; 1 minute >100000 MΩ
RC between leads, for C >1µF at 100 V; 1 minute >100000 s
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak
discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA);
rise time 100 V/s 400 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 42... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 44... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 45... on request
Fig.7 Outline.
296x12(full_width)
CBA355
P
seating plane(1)
A
h
lt
l
Ødt
b
α
(2)
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
1999 Apr 29 487
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =250 V; URac =160 V/Up-p =450 V
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.51 7.0 ×20.0 ×26.0 1.8 2222 479 42514
0.56 2222 479 42564
0.62 7.5 ×20.5 ×26.0 1.9 2222 479 42624
0.68 2222 479 42684
0.75 8.0 ×21.0 ×26.0 2.0 2222 479 42754
0.82 8.5 ×21.5 ×26.0 2.1 2222 479 42824
0.91 9.0 ×22.0 ×26.0 2.4 2222 479 42914
1.0 9.5 ×22.5 ×26.0 2.5 2222 479 42105
1.1 10.0 ×23.0 ×26.0 2.6 2222 479 42115
1.2 10.5 ×23.5 ×26.0 2.7 2222 479 42125
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
1.3 10.0 ×23.0 ×30.0 5.0 2222 479 42135
1.5 10.5 ×23.5 ×30.0 5.0 2222 479 42155
1.6 11.0 ×24.0 ×30.0 5.5 2222 479 42165
1.8 11.5 ×24.5 ×30.0 5.5 2222 479 42185
2.0 12.5 ×25.5 ×30.0 6.5 2222 479 42205
2.2 13.0 ×26.0 ×30.0 6.5 2222 479 42225
2.4 13.5 ×26.5 ×30.0 7.0 2222 479 42245
2.7 14.0 ×27.0 ×30.0 7.0 2222 479 42275
3.0 15.0 ×28.0 ×30.0 7.5 2222 479 42305
1999 Apr 29 488
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 10/15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 250 V DC capacitors (monitor type)
Available 250 V DC versions (monitor type)
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.022 µF<C≤0.027 µF≤5×10−4≤15 ×10−4
0.027 µF<C≤0.075 µF≤5×10−4≤20 ×10−4
0.075 µF<C≤0.11 µF≤5×10−4≤25 ×10−4
0.11 µF<C≤0.18 µF≤10 ×10−4≤30 ×10−4
0.18 µF<C≤0.22 µF≤10 ×10−4≤35 ×10−4
Rated voltage pulse slope (dU/dt)R at 250 V (DC):
P=10.0 mm 160 V/µs
P=15.0 mm 140 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 400 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 41... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 43... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 47... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 49... preferred
handbook, full pagewidth
seating plane
(1)
PØdt
b
l
h
l
t
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅d
t
H
15
Fig.8 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm
F=7.5 +0.6/−0.1 mm
1999 Apr 29 489
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Monitor
Monitor
URdc =250 V; URac =160 V/Up-p =450 V (monitor type)
Notes
1. Dimensions in brackets for bent back leads.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =10.0 ±0.4 mm; dt=0.60 ±0.06 mm; A =2.0 +1/−0.5 mm
0.022
6.0 ×15.0 ×12.5 0.9
2222 479 41223
not available
0.024 2222 479 41243
0.027 2222 479 41273
0.03 2222 479 41303
0.033 2222 479 41333
0.036 2222 479 41363
0.039 2222 479 41393
0.043 2222 479 41433
0.047 2222 479 41473
Pitch =15.0 ±0.4 mm (Pitch =7.5 0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.051
6.5 ×15.5 (17.0) ×17.5 1.3
2222 479 41513 .. 49513
0.056 2222 479 41563 .. 49563
0.062 2222 479 41623 .. 49623
0.068 2222 479 41683 .. 49683
0.075 2222 479 41753 .. 49753
0.082 2222 479 41823 .. 49823
0.091
7.0 ×16.0 (17.5) ×17.5 1.4
2222 479 41913 .. 49913
0.1 2222 479 41104 .. 49104
0.11 2222 479 41114 .. 49114
0.12 2222 479 41124 .. 49124
0.13 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 41134 .. 49134
0.15 2222 479 41154 .. 49154
0.16 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 41164 .. 49164
0.18 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 41184 .. 49184
0.2 2222 479 41204 .. 49204
0.22 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 41224 .. 49224
1999 Apr 29 490
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 250 V DC capacitors (monitor type)
Available 250 V DC versions (monitor type)
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.24 µF<C≤0.3 µF≤10 ×10−4≤35 ×10−4
0.3 µF<C≤0.39 µF≤10 ×10−4≤40 ×10−4
0.39 µF<C≤0.56 µF≤10 ×10−4≤45 ×10−4
0.56 µF<C≤0.68 µF≤10 ×10−4≤50 ×10−4
0.68 µF<C≤0.82 µF≤10 ×10−4≤55 ×10−4
0.82 µF<C≤0.91 µF≤10 ×10−4≤60 ×10−4
0.91 µF<C≤1.0 µF≤10 ×10−4≤65 ×10−4
1.0 µF<C≤1.2 µF≤10 ×10−4≤70 ×10−4
Rated voltage pulse slope (dU/dt)R at 250 V (DC):
P=22.5 mm 70 V/µs
P=27.5 mm 50 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
RC between leads, for C >1.0 µF at 100 V; 1 minute >100000 s
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 400 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 41... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 43... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 47... on request
Fig.9 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
296x12(full_width)
CBA355
P
seating plane
(1)
A
h
lt
l
Ødt
b
α
(2
)
1999 Apr 29 491
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Monitor
Monitor
URdc =250 V; URac =160 V/Up-p =450 V (monitor type)
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.24 6.5 ×19.5 ×26.0 1.7 2222 479 41244
0.27 7.0 ×20.0 ×26.0 1.8 2222 479 41274
0.3 7.5 ×20.5 ×26.0 1.9 2222 479 41304
0.33 2222 479 41334
0.36 8.0 ×21.0 ×26.0 2.0 2222 479 41364
0.39 8.5 ×21.5 ×26.0 2.1 2222 479 41394
0.43 2222 479 41434
0.47 9.0 ×22.0 ×26.0 2.4 2222 479 41474
0.51 9.5 ×22.5 ×26.0 2.5 2222 479 41514
0.56 10.0 ×23.0 ×26.0 2.6 2222 479 41564
0.62 10.5 ×23.5 ×26.0 2.7 2222 479 41624
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.68 10.0 ×23.0 ×30.0 5.0 2222 479 41684
0.75 10.5 ×23.5 ×30.0 5.0 2222 479 41754
0.82 11.0 ×24.0 ×30.0 5.5 2222 479 41824
0.91 11.5 ×24.5 ×30.0 5.5 2222 479 41914
1.0 12.0 ×25.0 ×30.0 6.0 2222 479 41105
1.1 12.5 ×25.5 ×30.0 6.5 2222 479 41115
1.2 13.0 ×26.0 ×30.0 6.5 2222 479 41125
1999 Apr 29 492
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 10/15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 400 V DC capacitors
Available 400 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.022 µF<C≤0.027 µF≤5×10−4≤15 ×10−4
0.027 µF<C≤0.075 µF≤5×10−4≤20 ×10−4
0.075 µF<C≤0.11 µF≤5×10−4≤25 ×10−4
0.11 µF<C≤0.18 µF≤10 ×10−4≤30 ×10−4
0.18 µF<C≤0.22 µF≤10 ×10−4≤35 ×10−4
Rated voltage pulse slope (dU/dt)R at 400 V (DC):
P=10.0 mm 80 V/µs
P=15.0 mm 70 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 640 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 52... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 54... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 55... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 56... preferred
Fig.10 Outline.
handbook, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
1999 Apr 29 493
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =400 V; URac =200 V/Up-p =560 V
Notes
1. Dimensions in brackets for bent back leads.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =10.0 ±0.4 mm; dt=0.60 ±0.06 mm; A =2.0 +1/−0.5 mm
0.022
6.0 ×15.0 ×12.5 0.9
2222 479 52223
not available
0.024 2222 479 52243
0.027 2222 479 52273
0.03 2222 479 52303
0.033 2222 479 52333
0.036 2222 479 52363
0.039 2222 479 52393
0.043 2222 479 52433
0.047 2222 479 52473
Pitch =15.0 ±0.4 mm; (pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.051
6.5 ×15.5 (17.0) ×17.5 1.3
2222 479 52513 .. 56513
0.056 2222 479 52563 .. 56563
0.062 2222 479 52623 .. 56623
0.068 2222 479 52683 .. 56683
0.075 2222 479 52753 .. 56753
0.082 2222 479 52823 .. 56823
0.091
7.0 ×16.0 (17.5) ×17.5 1.4
2222 479 52913 .. 56913
0.1 2222 479 52104 .. 56104
0.11 2222 479 52114 .. 56114
0.12 2222 479 52124 .. 56124
0.13 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 52134 .. 56134
0.15 2222 479 52154 .. 56154
0.16 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 52164 .. 56164
0.18 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 52184 .. 56184
0.2 2222 479 52204 .. 56204
0.22 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 52224 .. 56224
1999 Apr 29 494
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 400 V DC capacitors
Available 400 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.24 µF<C≤0.3 µF≤10 ×10−4≤35 ×10−4
0.3 µF<C≤0.39 µF≤10 ×10−4≤40 ×10−4
0.39 µF<C≤0.56 µF≤10 ×10−4≤45 ×10−4
0.56 µF<C≤0.68 µF≤10 ×10−4≤50 ×10−4
0.68 µF<C≤0.82 µF≤10 ×10−4≤55 ×10−4
0.82 µF<C≤0.91 µF≤10 ×10−4≤60 ×10−4
0.91 µF<C≤1.0 µF≤10 ×10−4≤65 ×10−4
1.0 µF<C≤1.2 µF≤10 ×10−4≤70 ×10−4
Rated voltage pulse slope (dU/dt)R at 400 V (DC):
P=22.5 mm 35 V/µs
P=27.5 mm 25 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
RC between leads, for C >1.0 µF at 100 V; 1 minute >100000 s
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 640 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 52... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 54... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 55... on request
Fig.11 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
296x12(full_width)
CBA355
P
seating plane
(1)
A
h
lt
l
Ødt
b
α
(2
)
1999 Apr 29 495
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =400 V; URac =200 V/Up-p =450 V
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.24 6.5 ×19.5 ×26.0 1.7 2222 479 52244
0.27 7.0 ×20.0 ×26.0 1.8 2222 479 52274
0.3 7.5 ×20.5 ×26.0 1.9 2222 479 52304
0.33 2222 479 52334
0.36 8.0 ×21.0 ×26.0 2.0 2222 479 52364
0.39 8.5 ×21.5 ×26.0 2.1 2222 479 52394
0.43 2222 479 52434
0.47 9.0 ×22.0 ×26.0 2.4 2222 479 52474
0.51 9.5 ×22.5 ×26.0 2.5 2222 479 52514
0.56 10.0 ×23.0 ×26.0 2.6 2222 479 52564
0.62 10.5 ×23.5 ×26.0 2.7 2222 479 52624
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.68 10.0 ×23.0 ×30.0 5.0 2222 479 52684
0.75 10.5 ×23.5 ×30.0 5.0 2222 479 52754
0.82 11.0 ×24.0 ×30.0 5.5 2222 479 52824
0.91 11.5 ×24.5 ×30.0 5.5 2222 479 52914
1.0 12.0 ×25.0 ×30.0 6.0 2222 479 52105
1.1 12.5 ×25.5 ×30.0 6.5 2222 479 52115
1.2 13.0 ×26.0 ×30.0 6.5 2222 479 52125
1999 Apr 29 496
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 10/15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 400 V DC capacitors (monitor type)
Available 400 V DC versions (monitor type)
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height; P0= sprocket hole distance; for detailed specifications refer to this handbook,
chapter
“Packaging information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.01 µF<C≤0.027 µF≤5×10−4≤15 ×10−4
0.027 µF<C≤0.075 µF≤5×10−4≤20 ×10−4
0.075 µF<C≤0.11 µF≤5×10−4≤25 ×10−4
Rated voltage pulse slope (dU/dt)R at 400 V (DC):
P=10.0 mm 200 V/µs
P=15.0 mm 180 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 640 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 51... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 53... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 57... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 59... preferred
Fig.12 Outline.
o
ok, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
1999 Apr 29 497
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Monitor
Monitor
URdc =400 V; URac =200 V/Up-p =560 V (monitor type)
Notes
1. Dimensions in brackets for bent back leads.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =10.0 ±0.4 mm; dt=0.60 ±0.06 mm; A =2.0 +1/−0.5 mm
0.01
6.0 ×15.0 ×12.5 0.9
2222 479 51103
not available
0.011 2222 479 51113
0.012 2222 479 51123
0.013 2222 479 51133
0.015 2222 479 51153
0.016 2222 479 51163
0.018 2222 479 51183
0.02 2222 479 51203
0.022 2222 479 51223
0.024 2222 479 51243
0.027 6.5 ×15.5 ×12.5 1.0 2222 479 51273
Pitch =15.0 ±0.4 mm; (pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.03
6.5 ×15.5 (17.0) ×17.5 1.3
2222 479 51303 .. 59303
0.033 2222 479 51333 .. 59333
0.036 2222 479 51363 .. 59363
0.039 2222 479 51393 .. 59393
0.043 2222 479 51433 .. 59433
0.047 2222 479 51473 .. 59473
0.051 2222 479 51513 .. 59513
0.056 2222 479 51563 .. 59563
0.062 7.0 ×16.0 (17.5) ×17.5 1.4 2222 479 51623 .. 59623
0.068 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 51683 .. 59683
0.075 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 51753 .. 59753
0.082 2222 479 51823 .. 59823
0.091 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 51913 .. 59913
0.1 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 51104 .. 59104
0.11 9.5 ×18.5 (20.0) ×17.5 1.9 2222 479 51114 .. 59114
1999 Apr 29 498
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 400 V DC capacitors (monitor type)
Available 400 V DC versions (monitor type)
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.12 µF<C≤0.18 µF≤10 ×10−4≤30 ×10−4
0.18 µF<C≤0.3 µF≤10 ×10−4≤35 ×10−4
0.3 µF<C≤0.39 µF≤10 ×10−4≤40 ×10−4
0.39 µF<C≤0.56 µF≤10 ×10−4≤45 ×10−4
0.56 µF<C≤0.68 µF≤10 ×10−4≤50 ×10−4
Rated voltage pulse slope (dU/dt)R at 400 V (DC):
P=22.5 mm 90 V/µs
P=27.5 mm 60 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 100 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 640 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 51... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 53... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 57... on request
Fig.13 Outline.
296x12(full_width)
CBA355
P
seating plane
(1)
A
h
lt
l
Ødt
b
α
(2
)
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
1999 Apr 29 499
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Monitor
Monitor
URdc =400 V; URac =200 V/Up-p =560 V (monitor type)
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.12 6.5 ×19.5 ×26.0 1.7 2222 479 51124
0.13 7.0 ×20.0 ×26.0 1.8 2222 479 51134
0.15 7.5 ×20.5 ×26.0 1.9 2222 479 51154
0.16 2222 479 51164
0.18 8.0 ×21.0 ×26.0 2.0 2222 479 51184
0.20 8.5 ×21.5 ×26.0 2.1 2222 479 51204
0.22 9.0 ×22.0 ×26.0 2.4 2222 479 51224
0.24 2222 479 51244
0.27 9.5 ×22.5 ×26.0 2.5 2222 479 51274
0.30 10.0 ×23.0 ×26.0 2.7 2222 479 51304
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.33 9.5 ×22.5 ×30.0 5.0 2222 479 51334
0.36 10.0 ×22.5 ×30.0 5.0 2222 479 51364
0.39 10.5 ×23.0 ×30.0 5.0 2222 479 51394
0.43 11.0 ×23.0 ×30.0 5.5 2222 479 51434
0.47 11.5 ×24.5 ×30.0 5.5 2222 479 51474
0.51 12.0 ×25.0 ×30.0 6.0 2222 479 51514
0.56 13.0 ×26.0 ×30.0 6.5 2222 479 51564
0.62 13.5 ×26.5 ×30.0 6.5 2222 479 51624
0.68 14.0 ×27.0 ×30.0 7.0 2222 479 51684
1999 Apr 29 500
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 10/15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 630 V DC capacitors
Available 630 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height; P0= sprocket hole distance; for detailed specifications refer to this handbook,
chapter
“Packaging information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.01 µF<C≤0.027 µF≤5×10−4≤15 ×10−4
0.027 µF<C≤0.075 µF≤5×10−4≤20 ×10−4
0.075 µF<C≤0.11 µF≤5×10−4≤25 ×10−4
Rated voltage pulse slope (dU/dt)R at 630 V (DC):
P=10.0 mm 100 V/µs
P=15.0 mm 90 V/µs
R between leads, for C ≤1.0 µF at 500 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 1008 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 62... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 64... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 65... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 66... preferred
Fig.14 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
handbook, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
1999 Apr 29 501
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =630 V; URac =200 V/Up-p =560 V
Notes
1. Dimensions in brackets for bent back leads.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =10.0 ±0.4 mm; dt=0.60 ±0.06 mm; A =2.0 +1/−0.5 mm
0.01
6.0 ×15.0 ×12.5 0.9
2222 479 62103
not available
0.011 2222 479 62113
0.012 2222 479 62123
0.013 2222 479 62133
0.015 2222 479 62153
0.016 2222 479 62163
0.018 2222 479 62183
0.02 2222 479 62203
0.022 2222 479 62223
0.024 2222 479 62243
0.027 6.5 ×15.5 ×12.5 1.0 2222 479 62273
Pitch =15.0 ±0.4 mm; (pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.03
6.5 ×15.5 (17.0) ×17.5 1.3
2222 479 62303 .. 66303
0.033 2222 479 62333 .. 66333
0.036 2222 479 62363 .. 66363
0.039 2222 479 62393 .. 66393
0.043 2222 479 62433 .. 66433
0.047 2222 479 62473 .. 66473
0.051 2222 479 62513 .. 66513
0.056 2222 479 62563 .. 66563
0.062 7.0 ×16.0 (17.5) ×17.5 1.4 2222 479 62623 .. 66623
0.068 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 62683 .. 66683
0.075 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 62753 .. 66753
0.082 2222 479 62823 .. 66823
0.091 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 62913 .. 66913
0.1 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 62104 .. 66104
0.11 9.5 ×18.5 (20.0) ×17.5 1.9 2222 479 62114 .. 66114
1999 Apr 29 502
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 630 V DC capacitors
Available 630 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.12 µF<C≤0.18 µF≤10 ×10−4≤30 ×10−4
0.18 µF<C≤0.3 µF≤10 ×10−4≤35 ×10−4
0.3 µF<C≤0.39 µF≤10 ×10−4≤40 ×10−4
0.39 µF<C≤0.56 µF≤10 ×10−4≤45 ×10−4
0.56 µF<C≤0.68 µF≤10 ×10−4≤50 ×10−4
Rated voltage pulse slope (dU/dt)R at 630 V (DC):
P=22.5 mm 45 V/µs
P=27.5 mm 30 V/µs
R between leads, for C ≤1.0 µF at 500 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >220 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 1008 V; 1 minute
Withstanding (DC) voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 62... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 64... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 65... on request
Fig.15 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
296x12(full_width)
CBA355
P
seating plane
(1)
A
h
lt
l
Ødt
b
α
(2
)
1999 Apr 29 503
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =630 V; URac =200 V/Up-p =560 V
Note
1. The shading indicates preferred types.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.12 6.5 ×19.5 ×26.0 1.7 2222 479 62124
0.13 7.0 ×20.0 ×26.0 1.8 2222 479 62134
0.15 7.5 ×20.5 ×26.0 1.9 2222 479 62154
0.16 2222 479 62164
0.18 8.0 ×21.0 ×26.0 2.0 2222 479 62184
0.20 8.5 ×21.5 ×26.0 2.1 2222 479 62204
0.22 9.0 ×22.0 ×26.0 2.4 2222 479 62224
0.24 2222 479 62244
0.27 9.5 ×22.5 ×26.0 2.5 2222 479 62274
0.30 10.0 ×23.0 ×26.0 2.7 2222 479 62304
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.33 9.5 ×22.5 ×30.0 5.0 2222 479 62334
0.36 10.0 ×22.5 ×30.0 5.0 2222 479 62364
0.39 10.5 ×23.0 ×30.0 5.0 2222 479 62394
0.43 11.0 ×23.0 ×30.0 5.5 2222 479 62434
0.47 11.5 ×24.5 ×30.0 5.5 2222 479 62474
0.51 12.0 ×25.0 ×30.0 6.0 2222 479 62514
0.56 13.0 ×26.0 ×30.0 6.5 2222 479 62564
0.62 13.5 ×26.5 ×30.0 6.5 2222 479 62624
0.68 14.0 ×27.0 ×30.0 7.0 2222 479 62684
1999 Apr 29 504
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 1000 V DC capacitors
Available 1000 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.039 µF≤5×10−4≤15 ×10−4
Rated voltage pulse slope (dU/dt)R at 1000 V (DC) 450 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >440 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 1600 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 72... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 74... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 75... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 76... preferred
Fig.16 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
o
ok, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
1999 Apr 29 505
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =1000 V; URac =350 V/Up-p =1000 V
Notes
1. Dimensions in brackets for bent back leads.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
4. Under development.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm
(bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =15.0 ±0.4 mm; (pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.013(4) 6.0 ×15.0 (16.5) ×17.5 1.2 2222 479 72133 .. 76133
0.015(4) 6.5 ×15.5 (17.0) ×17.5 1.3 2222 479 72153 .. 76153
0.016(4) 2222 479 72163 .. 76163
0.018(4) 7.0 ×16.0 (17.5) ×17.5 1.4 2222 479 72183 .. 76183
0.02(4) 2222 479 72203 .. 76203
0.022(4) 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 72223 .. 76223
0.024(4) 2222 479 72243 .. 76243
0.027(4) 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 72273 .. 76273
0.03(4) 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 72303 .. 76303
0.033(4) 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 72333 .. 76333
0.036(4) 9.5 ×18.5 (20.0) ×17.5 1.9 2222 479 72363 .. 76363
0.039(4) 2222 479 72393 .. 76393
1999 Apr 29 506
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 1000 V DC capacitors
Available 1000 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.039 µF<C≤0.1 µF≤5×10−4≤20 ×10−4
0.1 µF<C≤0.15 µF≤5×10−4≤25 ×10−4
0.15 µF<C≤0.22 µF≤5×10−4≤30 ×10−4
0.22 µF<C≤0.27 µF≤5×10−4≤35 ×10−4
Rated voltage pulse slope (dU/dt)R at 1000 V (DC):
P=22.5 mm 200 V/µs
P=27.5 mm 110 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >440 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 1600 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 72... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 74... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 75... on request
Fig.17 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
296x12(full_width)
CBA355
P
seating plane(1)
A
h
lt
l
Ødt
b
α
(2)
1999 Apr 29 507
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =1000 V; URac =350 V/Up-p =1000 V
Notes
1. The shading indicates preferred types.
2. Under development.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.043(2) 7.0 ×19.0 ×26.0 1.8 2222 479 72433
0.047(2) 2222 479 72473
0.051(2) 7.5 ×19.5 ×26.0 1.9 2222 479 72513
0.056(2) 2222 479 72563
0.062(2) 8.0 ×21.0 ×26.0 2.0 2222 479 72623
0.068(2) 8.5 ×21.5 ×26.0 2.1 2222 479 72683
0.075(2) 2222 479 72753
0.082(2) 9.0 ×22.0 ×26.0 2.3 2222 479 72823
0.091(2) 9.5 ×22.5 ×26.0 2.5 2222 479 72913
0.1(2) 10.0 ×23.0 ×26.0 2.6 2222 479 72104
0.11(2) 10.5 ×23.5 ×26.0 2.7 2222 479 72114
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.12(2) 9.5 ×22.5 ×31.0 5.0 2222 479 72124
0.13(2) 10.0 ×23.0 ×31.0 5.0 2222 479 72134
0.15(2) 11.0 ×24.0 ×31.0 5.5 2222 479 72154
0.16(2) 2222 479 72164
0.18(2) 12.0 ×25.0 ×31.0 6.0 2222 479 72184
0.20(2) 12.5 ×25.5 ×31.0 6.5 2222 479 72204
0.22(2) 13.0 ×26.0 ×31.0 6.5 2222 479 72224
0.24(2) 14.0 ×27.0 ×31.0 7.0 2222 479 72244
0.27(2) 14.5 ×27.5 ×31.0 7.5 2222 479 72274
1999 Apr 29 508
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 1250 V DC capacitors
Available 1250 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.024 µF≤5×10−4≤15 ×10−4
Rated voltage pulse slope (dU/dt)R at 1250 V (DC) 550 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >500 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 2000 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 82... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 84... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 85... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 86... preferred
Fig.18 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
handbook, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
1999 Apr 29 509
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =1250 V; URac =440 V/Up-p =1250 V
Notes
1. Dimensions in brackets for bent back leads
.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
4. Under development.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =15.0 ±0.4 mm; (pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.0082(4) 6.0 ×15.0 (16.5) ×17.5 1.2 2222 479 82822 .. 86822
0.0091(4)
6.5 ×15.5 (17.0) ×17.5 1.3 2222 479 82912 .. 86912
0.01(4) 2222 479 82103 .. 86103
0.011(4) 2222 479 82113 .. 86113
0.012(4) 7.0 ×16.0 (17.5) ×17.5 1.4 2222 479 82123 .. 86123
0.013(4) 2222 479 82133 .. 86133
0.015(4) 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 82153 .. 86153
0.016(4) 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 82163 .. 86163
0.018(4) 2222 479 82183 .. 86183
0.02(4) 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 82203 .. 86203
0.022(4) 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 82223 .. 86223
0.024(4) 9.5 ×18.5 (20.0) ×17.5 1.9 2222 479 82243 .. 86243
1999 Apr 29 510
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 1250 V DC capacitors
Available 1250 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.024 µF<C≤0.068 µF≤5×10−4≤20 ×10−4
0.068 µF<C≤0.1 µF≤5×10−4≤25 ×10−4
0.1 µF<C≤0.18 µF≤5×10−4≤30 ×10−4
Rated voltage pulse slope (dU/dt)R at 1000 V (DC):
P=22.5 mm 250 V/µs
P=27.5 mm 140 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 50 pC peak discharge >500 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 2000 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 82... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 84... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 85... on request
Fig.19 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
9
6x12(full_width)
9
6x12(full_width)
CBA355
P
seating plane(1)
A
h
lt
l
Ødt
b
α
(2)
1999 Apr 29 511
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =1250 V; URac =440 V/Up-p =1250 V
Notes
1. The shading indicates preferred types.
2. Under development.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.027(2) 6.5 ×18.5 ×26.0 1.7 2222 479 82273
0.03(2) 7.0 ×19.0 ×26.0 1.8 2222 479 82303
0.033(2) 7.5 ×19.5 ×26.0 1.9 2222 479 82333
0.036(2) 2222 479 82363
0.039(2) 8.0 ×21.0 ×26.0 2.0 2222 479 82393
0.043(2) 2222 479 82433
0.047(2) 8.5 ×21.5 ×26.0 2.1 2222 479 82473
0.051(2) 9.0 ×22.0 ×26.0 2.3 2222 479 82513
0.056(2) 9.5 ×22.5 ×26.0 2.5 2222 479 82563
0.062(2) 10.0 ×23.0 ×26.0 2.6 2222 479 82623
0.068(2) 10.5 ×23.5 ×26.0 2.7 2222 479 82683
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.075(2) 9.5 ×22.5 ×31.0 5.0 2222 479 82753
0.082(2) 10.0 ×23.0 ×31.0 5.0 2222 479 82823
0.091(2) 10.5 ×23.5 ×31.0 5.5 2222 479 82913
0.1(2) 11.0 ×24.0 ×31.0 5.5 2222 479 82104
0.11(2) 11.5 ×24.5 ×31.0 6.0 2222 479 82114
0.12(2) 12.0 ×25.0 ×31.0 6.0 2222 479 82124
0.13(2) 12.5 ×25.5 ×31.0 6.5 2222 479 82134
0.15(2) 13.5 ×26.5 ×31.0 7.0 2222 479 82154
0.16(2) 14.0 ×27.0 ×31.0 7.0 2222 479 82164
0.18(2) 15.0 ×28.0 ×31.0 7.5 2222 479 82184
1999 Apr 29 512
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 1600 V DC capacitors
Available 1600 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.013 µF≤5×10−4≤15 ×10−4
Rated voltage pulse slope (dU/dt)R at 1600 V (DC) 1400 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 20 pC peak discharge >660 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 2560 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 02... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 04... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 05... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 06... preferred
Fig.20 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
handbook, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
1999 Apr 29 513
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =1600 V; URac =550 V/Up-p =1600 V
Notes
1. Dimensions in brackets for bent back leads
.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
;
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
4. Under development.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =15.0 ±0.4 mm (Pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.0047(4) 6.0 ×15.0 (16.5) ×17.5 1.2 2222 479 02472 .. 06472
0.0051(4) 2222 479 02512 .. 06512
0.0056(4) 6.5 ×15.5 (17.0) ×17.5 1.3 2222 479 02562 .. 06562
0.0062(4) 2222 479 02622 .. 06622
0.0068(4) 7.0 ×16.0 (17.5) ×17.5 1.4 2222 479 02682 .. 06682
0.0075(4) 2222 479 02752 .. 06752
0.0082(4) 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 02822 .. 06822
0.0091(4) 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 02912 .. 06912
0.01(4) 2222 479 02103 .. 06103
0.011(4) 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 02113 .. 06113
0.012(4) 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 02123 .. 06123
0.013(4) 2222 479 02133 .. 06133
1999 Apr 29 514
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 1600 V DC capacitors
Available 1600 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.013 µF<C≤0.036 µF≤5×10−4≤20 ×10−4
0.036 µF<C≤0.1 µF≤5×10−4≤25 ×10−4
Rated voltage pulse slope (dU/dt)R at 1600 V (DC):
P=22.5 mm 550 V/µs
P=27.5 mm 350 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 20 pC peak discharge >660 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 2560 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 02... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 04... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 05... on request
Fig.21 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
296x12(full_width)
CBA355
P
seating plane(1)
A
h
lt
l
Ødt
b
α
(2)
1999 Apr 29 515
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =1600 V; URac =550 V/Up-p =1600 V
Notes
1. The shading indicates preferred types.
2. Under development.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.015(2) 6.5 ×18.5 ×26.0 1.7 2222 479 02153
0.016(2) 7.0 ×19.0 ×26.0 1.8 2222 479 02163
0.018(2) 2222 479 02183
0.02(2) 7.5 ×19.5 ×26.0 1.9 2222 479 02203
0.022(2) 8.0 ×21.0 ×26.0 2.0 2222 479 02223
0.024(2) 2222 479 02243
0.027(2) 8.5 ×21.5 ×26.0 2.1 2222 479 02273
0.03(2) 9.0 ×22.0 ×26.0 2.3 2222 479 02303
0.033(2) 9.5 ×22.5 ×26.0 2.5 2222 479 02333
0.036(2) 10.0 ×23.0 ×26.0 2.6 2222 479 02363
0.039(2) 10.5 ×23.5 ×26.0 2.7 2222 479 02393
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.043(2) 10.0 ×23.0 ×31.0 5.0 2222 479 02433
0.047(2) 2222 479 02473
0.051(2) 10.5 ×23.5 ×31.0 5.5 2222 479 02513
0.056(2) 11.0 ×24.0 ×31.0 5.5 2222 479 02563
0.062(2) 12.0 ×25.0 ×31.0 6.0 2222 479 02623
0.068(2) 12.5 ×25.5 ×31.0 6.5 2222 479 02683
0.075(2) 13.0 ×26.0 ×31.0 6.5 2222 479 02753
0.082(2) 13.5 ×26.5 ×31.0 7.0 2222 479 02823
0.091(2) 14.5 ×27.5 ×31.0 7.5 2222 479 02913
0.1(2) 15.0 ×28.0 ×31.0 7.5 2222 479 02104
1999 Apr 29 516
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 15 mm
PITCH 7.5 mm (bent back leads)
Specific reference data for the 2000 V DC capacitors
Available 2000 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.0091 µF≤5×10−4≤15 ×10−4
Rated voltage pulse slope (dU/dt)R at 2000 V (DC) 1700 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 20 pC peak discharge >750 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 3200 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 12... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 14... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 15... on request
Taped on reel (bent back) H =16.0 mm; P0=15.0 mm; note 2 ±5% 2222 479 16... preferred
Fig.22 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
(3) F−F’<0.3 mm.
F=7.5 +0.6/−0.1 mm.
a
ndbook, full pagewidth
seating plane(1)
PØdt
b
l
h
lt
α
A
(2)
b
h'
l
CBA818
F'
F
(3)
10 ∅dt
H
15
1999 Apr 29 517
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =2000 V; URac =700 V/Up-p =2000 V
Notes
1. Dimensions in brackets for bent back leads
.
2. H =in-tape height;P0=sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
:
a) For pitch =10.0 and 15.0 mm: H =16.0 mm and P0=12.7 mm.
b) For pitch =15/7.5 mm (bent back): H =16.0 mm and P0=15.0 mm.
Standard reel diameter =500 mm. Small reel diameter =356 mm is available on request.
3. The shading indicates preferred types.
4. Under development.
C
(µF)
DIMENSIONS(1)
bmax ×h (h’)max ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER
LOOSE IN BOX REEL DIAMETER =500 mm;
H=16.0 mm; P0=15.0 mm(2)
lt=5.0 ±1.0 mm pitch 7.5 mm (bent back)
C-tol =±5% C-tol =±5%
catalogue number(3) catalogue number(3)
Pitch =15.0 ±0.4 mm; (pitch =7.5 ±0.4 mm for bent back leads); dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.003(4) 6.0 ×15.0 (16.5) ×17.5 1.2 2222 479 12302 .. 16302
0.0033(4) 2222 479 12332 .. 16332
0.0036(4) 6.5 ×15.5 (17.0) ×17.5 1.3 2222 479 12362 .. 16362
0.0039(4) 2222 479 12392 .. 16392
0.0043(4) 7.0 ×16.0 (17.5) ×17.5 1.4 2222 479 12432 .. 16432
0.0047(4) 2222 479 12472 .. 16472
0.0051(4) 7.5 ×16.5 (18.0) ×17.5 1.5 2222 479 12512 .. 16512
0.0056(4) 2222 479 12562 .. 16562
0.0062(4) 8.0 ×17.0 (18.5) ×17.5 1.6 2222 479 12622 .. 16622
0.0068(4) 8.5 ×17.5 (19.0) ×17.5 1.7 2222 479 12682 .. 16682
0.0075(4) 2222 479 12752 .. 16752
0.0082(4) 9.0 ×18.0 (19.5) ×17.5 1.8 2222 479 12822 .. 16822
0.0091(4) 9.5 ×18.5 (20.0) ×17.5 1.9 2222 479 12912 .. 16912
1999 Apr 29 518
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 2000 V DC capacitors
Available 2000 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
0.0091 µF<C≤0.027 µF≤5×10−4≤18 ×10−4
0.027 µF<C≤0.056 µF≤5×10−4≤20 ×10−4
Rated voltage pulse slope (dU/dt)R at 2000 V (DC):
P=22.5 mm 700 V/µs
P=27.5 mm 450 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 20 pC peak discharge >750 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 3200 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 12... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 14... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 15... on request
Fig.23 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°.
296x12(full_width)
CBA355
P
seating plane(1)
A
h
lt
l
Ødt
b
α
(2)
1999 Apr 29 519
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =2000 V; URac =700 V/Up-p =2000 V
Notes
1. The shading indicates preferred types.
2. Under development.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.01(2) 6.5 ×18.5 ×26.0 1.7 2222 479 12103
0.011(2) 7.0 ×19.0 ×26.0 1.8 2222 479 12113
0.012(2) 2222 479 12123
0.013(2) 7.5 ×19.5 ×26.0 1.9 2222 479 12133
0.015(2) 8.0 ×21.0 ×26.0 2.0 2222 479 12153
0.016(2) 2222 479 12163
0.018(2) 8.5 ×21.5 ×26.0 2.1 2222 479 12183
0.02(2) 9.0 ×22.0 ×26.0 2.3 2222 479 12203
0.022(2) 9.5 ×22.5 ×26.0 2.5 2222 479 12223
0.024(2) 10.0 ×23.0 ×26.0 2.6 2222 479 12243
0.027(2) 10.5 ×23.5 ×26.0 2.7 2222 479 12273
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.03(2) 10.0 ×23.0 ×31.0 5.0 2222 479 12303
0.033(2) 10.5 ×23.5 ×31.0 5.5 2222 479 12333
0.036(2) 11.0 ×24.0 ×31.0 5.5 2222 479 12363
0.039(2) 11.5 ×24.5 ×31.0 6.0 2222 479 12393
0.043(2) 12.0 ×25.0 ×31.0 6.0 2222 479 12433
0.047(2) 13.0 ×26.0 ×31.0 6.5 2222 479 12473
0.051(2) 13.5 ×26.5 ×31.0 7.0 2222 479 12513
0.056(2) 14.0 ×27.0 ×31.0 7.0 2222 479 12563
1999 Apr 29 520
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MKP 479 GENERAL DATA PITCH 22.5/27.5 mm
Specific reference data for the 2500 V DC capacitors
Available 2500 V DC versions
Notes
1. For SPQ refer to this handbook, chapter
“Packaging information”
; taped on reel pitch = 27.5 mm is not available.
2. H = in-tape height;P0= sprocket hole distance; for detailed specifications refer to this handbook, chapter
“Packaging
information”
.
DESCRIPTION VALUE
at 10 kHz at 100 kHz
Tangent of loss angle:
C≤0.033 µF≤5×10−4≤15 ×10−4
Rated voltage pulse slope (dU/dt)R at 2500 V (DC):
P=22.5 mm 1700 V/µs
P=27.5 mm 900 V/µs
R between leads, for C ≤1.0 µF at 100 V; 1 minute >100000 MΩ
R between leads and case; 500 V; 1 minute >100000 MΩ
Ionization (AC) voltage (typical value) at 20 pC peak discharge >1000 V
Withstanding (DC) voltage (cut off current 10 mA); rise time 100 V/s 3500 V; 1 minute
Withstanding (DC)voltage between leads and case 2840 V; 1 minute
PACKAGING(1) DIMENSIONS C-tol FIRST 9 DIGITS OF
CATALOGUE NUMBER ORDERING
Loose in box lt=5.0 ±1.0 mm ±5% 2222 479 22... preferred
lt=3.5 ±0.5 mm ±5% 2222 479 24... on request
Taped on reel H =16.0 mm; P0=12.7 mm; note 2 ±5% 2222 479 25... on request
Fig.24 Outline.
(1) Hole ∅1.3 for dt=0.8 mm.
(2) 0 ≤α<50°
296x12(full_width)
CBA355
P
seating plane(1)
A
h
lt
l
Ødt
b
α
(2)
1999 Apr 29 521
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
URdc =2500 V; URac =900 V/Up-p =2500 V
Notes
1. The shading indicates preferred types.
2. Under development.
C
(µF)
DIMENSIONS
bmax ×hmax ×lmax
(mm)
MASS
(g)
CATALOGUE NUMBER(1)
LOOSE IN BOX
lt=5.0 ±1.0 mm
C-tol =±5%
Pitch =22.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.002(2)
7.0 ×19.0 ×26.0 1.8
2222 479 22202
0.0022(2) 2222 479 22222
0.0024(2) 2222 479 22242
0.0027(2) 2222 479 22272
0.003(2) 2222 479 22302
0.0033(2) 2222 479 22332
0.0036(2) 2222 479 22362
0.0039(2) 2222 479 22392
0.0043(2) 2222 479 22432
0.0047(2) 2222 479 22472
0.0051(2) 2222 479 22512
0.0056(2) 2222 479 22562
0.0062(2) 7.5 ×19.5 ×26.0 1.9 2222 479 22622
0.0068(2) 2222 479 22682
0.0075(2) 8.0 ×21.0 ×26.0 2.0 2222 479 22752
0.0082(2) 8.5 ×21.5 ×26.0 2.1 2222 479 22822
0.0091(2) 2222 479 22912
0.01(2) 9.0 ×22.0 ×26.0 2.3 2222 479 22103
0.011(2) 9.5 ×22.5 ×26.0 2.5 2222 479 22113
0.012(2) 10.0 ×23.0 ×26.0 2.6 2222 479 22123
0.013(2) 10.5 ×23.5 ×26.0 2.7 2222 479 22133
Pitch =27.5 ±0.4 mm; dt=0.80 ±0.08 mm; A =2.5 +1.4/−0.5 mm
0.015(2) 9.5 ×22.5 ×31.0 5.0 2222 479 22153
0.016(2) 10.0 ×23.0 ×31.0 5.0 2222 479 22163
0.018(2) 10.5 ×23.5 ×31.0 5.5 2222 479 22183
0.02(2) 11.0 ×24.0 ×31.0 5.5 2222 479 22203
0.022(2) 12.0 ×25.0 ×31.0 6.0 2222 479 22223
0.024(2) 12.5 ×25.5 ×31.0 6.5 2222 479 22243
0.027(2) 13.0 ×26.0 ×31.0 6.5 2222 479 22273
0.03(2) 14.0 ×27.0 ×31.0 7.0 2222 479 22303
0.033(2) 14.5 ×27.5 ×31.0 7.5 2222 479 22333
1999 Apr 29 522
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
CONSTRUCTION
Description
•Low-inductive wound cell of metallized polypropylene (PP) film, epoxy lacquered
•Radial leads, solder-coated wire:
– Copper clad steel wire for original pitch =10 and 15 mm
– Copper wire for original pitch =22.5 and 27.5 mm.
Fig.25 Construction: 160-250-400-630 V versions.
144x12(halfpage)
metal spray layer
MKP metallised polypropylene film
connecting wire
CBA403
1 SECTION
Fig.26 Construction: 1000 V-1250 V versions.
handbook, halfpage
CBA312
metal spray layer
MKP metallized polypropylene film
connecting wire
2 SECTIONS
Fig.27 Construction: 1600 V-2000 V versions.
a
ndbook, halfpage
CBA313
metal spray layer
MKP metallized polypropylene film
connecting wire
3 SECTIONS
Fig.28 Construction: 2500 V versions.
handbook, halfpage
CBA314
metal spray layer
MKP metallized polypropylene film
connecting wire
4 SECTIONS
1999 Apr 29 523
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Mounting
NORMAL USE
The capacitors are designed for mounting on
printed-circuit boards. The capacitors packed in bandoliers
are designed for mounting on printed-circuit boards by
automatic insertion machines.
For detailed tape specifications refer to this handbook,
chapter
“Packaging information”
.
SPECIFIC METHOD OF MOUNTING TO WITHSTAND VIBRATION
AND SHOCK
In order to withstand vibration and shock tests, it must be
ensured that the underside of the crimps are in good
contact with the printed-circuit board:
•For original pitches of ≤15 mm the capacitors shall be
mechanically fixed by the leads.
•For larger pitches the capacitors shall be mounted in the
same way and the body clamped.
Storage temperature
•Storage temperature: Tstg =−25 to +40 °C with RH
maximum 80% without condensation
.
RATINGS AND CHARACTERISTICS REFERENCE
CONDITIONS
Unless otherwise specified, all electrical values apply to an
ambient free air temperature of 23 ±1°C, an atmospheric
pressure of 86 to 106 kPa and a relative humidity of
50 ±2%.
For reference testing, a conditioning period shall be
applied over 96 ±4 hours by heating the products in a
circulating air oven at the rated temperature and a relative
humidity not exceeding 20%.
1999 Apr 29 524
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
CHARACTERISTICS
Capacitance
Impedance
Fig.29 Capacitance change at 1 kHz as a function of temperature.
handbook, full pagewidth
100−50 0 50
CBA505
4
−6
−4
− 2
0
2
max.
typical
min.
∆C
C
(%)
Tamb (°C)
Fig.30 Impedance as a function of frequency: typical curves.
296x12(full_width)
CBA335
108
107
106
105
104
102
10-3
10-2
10-1
100
101
impedance
(Ω)
f (Hz)
3.3 µF1.0 µF
100 nF
10 nF
1999 Apr 29 525
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Maximum DC and AC voltage as a function of temperature
handbook, full pagewidth
CBA748
1.2
0
0.8
0.4
1.0
0.6
0.2
factor
−60 −20 8040−40 0 20 60 100 120
Tamb (°C)
Fig.31 Multiplying factor for DC and AC voltage as a function of temperature.
1999 Apr 29 526
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Maximum RMS voltage (sinewave) as a function of frequency
Fig.32 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc =160 V.
296x12(full_width)
AC voltage
(V)
CBA357
106
105
104
103
102
103
101
102
f (Hz)
75 nF
220 nF
470 nF
1000 nF
2200 nF
3900 nF
120 nF
MKP 479
Fig.33 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc =160 V.
296x12(full_width)
AC voltage
(V)
CBA767
106
105
104
103
102
103
101
102
f (Hz)
MKP 479
75 nF
220 nF
470 nF
1000 nF
2200 nF
3900 nF
120 nF
1999 Apr 29 527
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.34 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc =250 V.
296x12(full_width)
AC voltage
(V)
CBA358
106
105
104
103
102
103
101
102
f (Hz)
47 nF
100 nF
3000 nF
1000 nF
470 nF
220 nF
2200 nF
MKP 479
Fig.35 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc =250 V.
296x12(full_width)
AC voltage
(V)
CBA768
106
105
104
103
102
103
101
102
f (Hz)
MKP 479
47 nF
100 nF
3000 nF
1000 nF
470 nF
220 nF
2200 nF
1999 Apr 29 528
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.36 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc =250 V
(monitor type).
296x12(full_width)
AC voltage
(V)
CBA946
106
105
104
103
102
103
101
102
f (Hz)
1200 nF
470 nF
220 nF
100 nF
47 nF
22 nF
MKP 479
Fig.37 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc =250 V
(monitor type).
296x12(full_width)
AC voltage
(V)
CBA947
106
105
104
103
102
103
101
102
f (Hz)
MKP 479
1200 nF
470 nF
220 nF
100 nF
47 nF
22 nF
1999 Apr 29 529
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.38 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc =400 V.
296x12(full_width)
AC voltage
(V)
CBA359
106
105
104
103
102
103
101
102
f (Hz)
1200 nF
470 nF
220 nF
100 nF
47 nF
22 nF
MKP 479
Fig.39 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc =400 V.
296x12(full_width)
AC voltage
(V)
CBA769
106
105
104
103
102
103
101
102
f (Hz)
MKP 479
1200 nF
470 nF
220 nF
100 nF
47 nF
22 nF
1999 Apr 29 530
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.40 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc =400 V
(monitor type).
296x12(full_width)
CBA360
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
10 nF
680 nF
470 nF
220 nF
100 nF
47 nF
22 nF
Fig.41 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc =400 V
(monitor type).
296x12(full_width)
CBA770
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
10 nF
680 nF
470 nF
220 nF
100 nF
47 nF
22 nF
1999 Apr 29 531
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.42 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc =630 V.
296x12(full_width)
CBA360
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
10 nF
680 nF
470 nF
220 nF
100 nF
47 nF
22 nF
Fig.43 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc =630 V.
296x12(full_width)
CBA770
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
10 nF
680 nF
470 nF
220 nF
100 nF
47 nF
22 nF
1999 Apr 29 532
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.44 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 1000 V.
296x12(full_width)
CBA905
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
15 nF
220 nF
150 nF
68 nF
33 nF
Fig.45 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc = 1000 V.
296x12(full_width)
CBA906
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
220 nF
150 nF
68 nF
33 nF
15 nF
1999 Apr 29 533
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.46 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 1250 V.
296x12(full_width)
CBA907
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
150 nF
100 nF
47 nF
10 nF
22 nF
Fig.47 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc = 1250 V.
296x12(full_width)
CBA908
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
150 nF
100 nF
47 nF
10 nF
22 nF
1999 Apr 29 534
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.48 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 1600 V.
296x12(full_width)
CBA909
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
100 nF
47 nF
10 nF
22 nF
4.7 nF
Fig.49 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc = 1600 V.
296x12(full_width)
CBA910
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
100 nF
47 nF
10 nF
22 nF
4.7 nF
1999 Apr 29 535
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Fig.50 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 2000 V.
296x12(full_width)
CBA911
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
3.3 nF
6.8 nF
15 nF
33 nF
47 nF
Fig.51 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc = 2000 V.
296x12(full_width)
CBA912
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
3.3 nF
6.8 nF
15 nF
33 nF
47 nF
1999 Apr 29 536
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Maximum RMS current (sinewave) as a function of frequency
The maximum RMS current is defined by .
Uac is the maximum AC voltage depending on the ambient temperature in Figs 32 to 53.
Fig.52 AC voltage (RMS value) as a function of frequency at Tamb ≤85 °C for URdc = 2500 V.
296x12(full_width)
CBA916
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
2.2 nF
4.7 nF
10 nF
22 nF
33 nF
Fig.53 AC voltage (RMS value) as a function of frequency at 85 °C<Tamb ≤105 °C for URdc = 2500 V.
296x12(full_width)
CBA917
AC voltage
(V)
107
106
105
104
103
103
101
102
f (Hz)
MKP 479
2.2 nF
4.7 nF
10 nF
22 nF
33 nF
Iac ωCU
ac
××=
1999 Apr 29 537
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Tangent of loss angle
Fig.54 Tangent of loss angle as a function of frequency; typical curves.
160 V:
C≤0.10 µF, curve 5.
C≤0.16 µF, curve 6.
C≤0.75 µF, curve 7.
C≤1.0 µF, curve 11.
C≤1.8 µF, curve 12.
C≤3.0 µF, curve 13.
C≤3.9 µF, curve 16.
250 V:
C≤0.068 µF, curve 4.
C≤0.091 µF, curve 5.
C≤0.220 µF, curve 6.
C≤0.470 µF, curve 7.
C≤0.680 µF, curve 10.
C≤1.0 µF, curve 12.
C≤2.0 µF, curve 14.
C≤2.7 µF, curve 15.
400 V:
C≤0.043 µF, curve 4.
C≤0.1 µF, curve 5.
C≤0.22 µF, curve 6.
C≤0.33 µF, curve 7.
C≤0.47 µF, curve 8.
C≤0.68 µF, curve 9.
C≤1.0 µF, curve 10.
C≤1.2 µF, curve 11.
630 V:
C≤0.024 µF, curve 4.
C≤0.047 µF, curve 5.
C≤0.11 µF, curve 6.
C≤0.22 µF, curve 6.
C≤0.3 µF, curve 7.
C≤0.47 µF, curve 9.
C≤0.68 µF, curve 10.
1000 V:
C≤0.039 µF, curve 2.
C≤0.1 µF, curve 3.
C≤0.15 µF, curve 4.
C≤0.22 µF, curve 5.
C≤0.27 µF, curve 6.
1250 V:
C≤0.024 µF, curve 2.
C≤0.068 µF, curve 3.
C≤0.1 µF, curve 4.
C≤0.18 µF, curve 5.
1600 V:
C≤0.013 µF, curve 2.
C≤0.033 µF, curve 3.
C≤0.1 µF, curve 4.
2000 V:
C≤0.091 µF, curve 1.
C≤0.027 µF, curve 2.
C≤0.056 µF, curve 3.
2500 V:
C≤0.033 µF, curve 1.
296x12(full_width)
CBA918
106107
105
104
103
102
103
100
102
101
dissipation
factor
(x 10-4)
f (Hz)
1
2
3
4
5
6
8
9
7
10
11
12
13
14
15
16
1999 Apr 29 538
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Insulation resistance
Maximum allowed component temperature rise (∆T) as a function of the ambient temperature (Tamb)
Fig.55 RC product as a function of ambient free air temperature; typical curve.
handbook, full pagewidth
RC
(s)
12010004020 8060
104
106
CBA647
105
Tamb (°C)
handbook, full pagewidth
CBA757
12
10
0
−60 −20 80
8
4
2
6
40
−40 0 20 60 100 120
Tamb (°C)
∆T
(°C)
Fig.56 Maximum allowed component temperature rise as a function of the ambient temperature.
1999 Apr 29 539
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Heat conductivity (G) as a function of pitch and capacitor body thickness in mW/°C
Table 1 Heat conductivity
Power dissipation and maximum component temperature rise
The power dissipation must be limited in order not to exceed the maximum allowed component temperature rise as a
function of the free air ambient temperature.
Power dissipation can be calculated in accordance with chapter
“Introduction”
, section
“Maximum power dissipation”
.
The component temperature rise (∆T) can be measured (see section “Measuring the component temperature” for more
details) or calculated by :
•∆T=component temperature rise (°C).
•P=power dissipation of the component (mW).
•G=heat conductivity of the component (mW/°C).
bmax
(mm)
ORIGINAL PITCH
(mm)
10 15 22.5 27.5
4.0 4.0 5.0 −−
4.5 4.5 6.0 −−
5.0 5.0 6.0 12.0 13.0
5.5 6.0 6.5 13.0 15.0
6.0 6.0 6.5 13.0 15.0
6.5 6.5 8.0 15.0 17.0
7.0 −8.0 15.0 17.0
7.5 −9.0 17.0 18.0
8.0 −9.0 17.0 20.0
8.5 −11.0 18.0 20.0
9.0 −11.0 18.0 22.0
9.5 −12.0 20.0 22.0
10.0 −12.0 20.0 23.0
10.5 −−22.0 25.0
11.0 −−−25.0
11.5 −−−27.0
12.0 −−−27.0
12.5 −−−30.0
13.0 −−−30.0
13.5 −−−30.0
14.0 −−−30.0
14.5 −−−33.0
15.0 −−−33.0
15.5 −−−37.0
16.0 −−−37.0
∆TPG⁄=
1999 Apr 29 540
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Measuring the component temperature
A thermocouple must be attached to the capacitor body; see Fig.57.
The temperature is measured in unloaded (Tamb) and maximum loaded
condition (Tc).
The temperature rise is given by .
To avoid radiation or convection, the capacitor should be tested in a wind-free
box.
Fig.57 Mounting the thermocouple.
handbook, halfpage
thermocouple
CBA771
∆TT
c
T
amb
–=
1999 Apr 29 541
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Application note and limiting conditions
These capacitors are not suitable for mains applications as across-the-line capacitors without additional
protection, as described hereunder. These mains applications are strictly regulated by safety standards and
therefore electromagnetic interference suppression capacitors conforming to the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The peak voltage (Up) shall not be greater than the rated DC voltage (URdc).
2. The peak-to-peak voltage (Up-p) shall not be greater than the maximum Up-p to avoid the ionisation inception level.
3. The voltage pulse slope (dU/dt) shall not exceed the rated voltage pulse slope in an RC-circuit at rated voltage and
without ringing. If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied
by URdc and divided by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration.
The rated voltage pulse slope is valid for ambient temperatures up to 85 °C. For higher temperatures a derating factor
of 3% per K shall be applied.
4. The maximum component surface temperature rise must be lower than the limits in Fig.56.
5. Since in circuits used at voltages over 280 V peak-to-peak the risk for an intrinsically active flammability after a
capacitor breakdown (short circuit) increases, it is recommended that the power to the component is limited to
100 times the values mentioned in Table 1 “Heat conductivity”.
6. When using these capacitors as across-the-line capacitor in the input filter for mains applications or as series
connected with an impedance to the mains the applicant must guarantee that following conditions are fulfilled in any
case (spikes and surge voltages from the mains included).
VOLTAGE CONDITIONS FOR 6ABOVE
ALLOWED VOLTAGES Tamb ≤85 °C85°C<T
amb ≤105 °C
Maximum continuous RMS voltage URac 0.7 ×URac
Maximum temporary RMS -overvoltage (<24 hours) 1.25 ×URac 0.875 ×URac
Maximum peak voltage (Vo-p) (<2 s) 1.6 ×URdc 1.1 ×URdc
2dU
dt
--------
2
0
T
∫dt×× URdc dU
dt
--------
rated
×<
1999 Apr 29 542
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Example: 2222 479 42474
C=470 nF, 250 V used for S-correction.
This is a signal as in Fig.58 with:
Up-p =108 V; Up=170 V; T1=12 µs; T2=64 µs; Ip-p =5A
The ambient temperature is 50 °C.
Checking the conditions:
1. The peak voltage Up=170 V is lower than 250 V (DC).
2. The peak-to-peak voltage 108 V is lower than .
3. Ip=2.5 A is lower than .
4. The dissipated power is about 40 mW as calculated with Fourier terms and tgδ maximum values.
This gives a temperature rise of which is permitted; see Fig.56.
5. Depends on actual application.
6. Not applicable.
2 2 160 V AC()×× 450 Upp–
=
0.47 µF60Vµs⁄× 28 A=
40 mW
12 mW °C⁄
------------------------------- 3.3 °C=
Fig.58 Voltage signal.
handbook, full pagewidth
T1
T2
Ipp
I
t
U
t
Up
Upp
CBA279
1999 Apr 29 543
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
MARKING
Product marking
Capacitors are marked on top in black ink (see Fig.59) with
the following information:
1. Manufacturer’s logo (only for original pitches >10 mm)
2. Rated capacitance code in accordance with
“IEC 60062”
3. Tolerance on rated capacitance J =±5%
4. Rated (DC) voltage (e.g. 400 V)
5. Manufacturer's type designation with code for
dielectric material (479 MKP)
6. Year and month of manufacture in code (e.g. K1);
see Table 2. Fig.59 Example of marking.
144x12(halfpage) 47n J 400V
479 MKP K1
CBA365
Table 2 Letter codes for year and numbers for month of production
YEAR LETTER CODE MONTH CODE
1998 K January 1
1999 L February 2
2000 M March 3
2001 N April 4
2002 P May 5
2003 R June 6
2004 S July 7
2005 T August 8
2006 U September 9
2007 V October O
2008 W November N
2009 X December D
1999 Apr 29 544
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Package marking
The package containing the capacitors is marked as shown in Fig.60.
handbook, full pagewidth
CCA325
1.
2.
3.
4.
5.
8.
7.
6.
9.
10.
Fig.60 Barcode label.
Barcode label marking
LINE MARKING EXPLANATION
1 Manufacturer’s name
2 Country of origin
3 Sub-family
4 Type description
5 Capacitance value in µF, tolerance, voltage
and climatic category
(“IEC 60068-1”)
6−
7•Country of origin: Belgium
Preference origin code: A
Country of origin in code: 170 (Belgium)
Responsible production centre: HQ
Work order: WO
•Country of origin: China
Preference origin code: N
Country of origin in code: 260 (PRC)
Responsible production centre: 07
8 Product type description
9 Quantity and production period, year and
week code
10 Product code (12NC)
Please note:
In due time BC COMPONENTS
will replace PHILIPS COMPONENTS
1999 Apr 29 545
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
QUICK REFERENCE TEST REQUIREMENTS (see note 1)
TEST PROCEDURE
(quick reference) REQUIREMENTS
Robustness of leads
Tensile:
“IEC 60068-2-21”
load 10 N; 10 s no visible damage
legible marking
∆C/C≤1%
for 250 to 2500 V: pitch = 22.5 or 27.5 mm
∆C/C≤2%
for 160 V: all pitches;
for 250 V to 2000 V:
original pitch =10 and 15 mm
∆tan δ≤5×10−4 (C ≤100 nF)
∆tan δ≤10 ×10−4 (100 nF <C≤470 nF)
∆tan δ≤15 ×10−4 (C >470 nF)
Bending:
“IEC 60068-2-21”
load 5 N; 4 ×90°
Resistance to soldering heat:
“IEC 60068-2-20”
solder bath: 260 °C; 10 s
Component solvent resistance isopropyl alcohol; 23 °C; 5 minutes
Robustness of component
Vibration:
“IEC 60068-2-6”
10 Hz to 55 kHz; amplitude
0.75 mm or acceleration 98 m/s2;
6 hours
∆C/C≤1%
for 250 to 2500 V: pitch = 22.5 or 27.5 mm
∆C/C≤2%
for 160 V: all pitches;
for 250 V to 2000 V:
original pitch =10 and 15 mm
∆tan δ≤5×10−4 (C ≤100 nF)
∆tan δ≤10 ×10−4 (100 nF <C≤470 nF)
∆tan δ≤15 ×10−4 (C >470 nF)
Shock:
“IEC 60068-2-27”
half sinewave; 490 m/s2; 11 ms
Climatic sequence
Dry heat:
“IEC 60068-2-2”
16 hours; 105 °C∆C/C≤1%
for 250 to 2500 V: pitch = 22.5 or 27.5 mm
∆C/C≤3%
for 160 V: all pitches;
for 250 V to 2000 V:
original pitch =10 and 15 mm
∆tan δ≤5×10−4 (C ≤100 nF)
∆tan δ≤10 ×10−4 (100 nF <C≤470 nF)
∆tan δ≤15 ×10−4 (C >470 nF)
Rins ≥50% of specified value
Damp heat, cyclic, test Db, first
cycle:
“IEC 60068-2-30”
Cold:
“IEC 60068-2-1”
2 hours; −55 °C
Damp heat, cyclic, test Db,
remaining cycles:
“IEC 60068-2-30”
Other applicable tests
Damp heat, steady state:
“IEC 60068-2-3”
56 days; 40 °C; 90 to 95% RH ∆C/C≤1%
for 250 to 2500 V: pitch = 22.5 or 27.5 mm
∆C/C≤3%
for 160 V: all pitches;
for 250 V to 2000 V:
original pitch = 10 and 15 mm
∆tan δ≤5×10−4
Rins ≥50% of specified value
1999 Apr 29 546
BC Components Product specification
AC and pulse metallized
polypropylene film capacitors MKP 479
Note
1. For detailed information: see
“Type detail specification HQN-384-17/105”
.
Endurance (AC):
“IEC 60384-17”
2000 hours; 85 °C
1.25 ×URac (RMS); 50 Hz
2000 hours; 105 °C
0.875 ×URac (RMS); 50 Hz
∆C/C≤5%
∆tan δ≤5×10−4 (C ≤100 nF)
∆tan δ≤10 ×10−4 (100 nF <C≤470 nF)
∆tan δ≤15 ×10−4 (C >470 nF)
Rins ≥50% of specified value
Heat storage:
“IEC 60384-17”
2000 hours; 105 °C∆C/C≤1%
for 250 to 2500 V: pitch = 22.5 or 27.5 mm
∆C/C≤3%
for 160 V: all pitches;
for 250 V to 2000 V:
original pitch = 10 and 15 mm
∆tan δ≤5×10−4 (C ≤100 nF)
∆tan δ≤10 ×10−4 (100 nF <C≤470 nF)
∆tan δ≤15 ×10−4 (C >470 nF)
Resistance to soldering heat with
preheating:
“IEC 60384-17”
body temperature: 105 °C
bath temperature: 260 °C
dwell time: 10 s
∆C/C≤1%
for 250 to 2500 V: pitch = 22.5 or 27.5 mm
∆C/C≤2%
for 160 V: all pitches;
for 250 V to 2000 V:
original pitch = 10 and 15 mm
∆tan δ≤5×10−4 (C ≤100 nF)
∆tan δ≤10 ×10−4 (100 nF <C≤470 nF)
∆tan δ≤15 ×10−4 (C >470 nF)
Passive flammability:
“IEC 60384-1”
class C no burning
Endurance (DC):
“IEC 60384-17”
2000 hours:
1.25 ×URdc; 85 °C
0.875 ×URdc; 105 °C
∆C/C≤1%
for 250 to 2500 V: pitch = 22.5 or 27.5 mm
∆C/C≤3%
for 160 V: all pitches;
for 250 V to 2000 V:
original pitch = 10 and 15 mm
∆tan δ≤5×10−4 (C ≤100 nF)
∆tan δ≤10 ×10−4 (100 nF <C≤470 nF)
∆tan δ≤15 ×10−4 (C >470 nF)
Rins ≥50% of specified value
TEST PROCEDURE
(quick reference) REQUIREMENTS
