DIB02CB23150MV - Carlo Gavazzi Group

Specifications are subject to change without notice (19.09.06) 1

Monitoring Relays

Product Description Ordering Key

Housing

Function

Type

Item number

Output

Power supply

Range

• TRMS AC/DC over or under current

monitoring relays

• Current measuring through external shunt or CT

•Selection of measuring range by DIP-switches

•Measuring ranges from 6 to 150 mV AC/DC and

0.4 to 4 VpAC(MI or MP range)

• Adjustable current on relative scale

• Adjustable hysteresis on relative scale

• Adjustable delay function (0.1 to 30 s)

• Programmable latching or inhibit at set level

• Output: 8 A SPDT relay N.D. or N.E. selectable

• For mounting on DIN-rail in accordance with

DIN/EN 50 022 (DIB02) or plug-in module (PIB02)

• 22.5 mm Euronorm housing (DIB02)

or36 mm plug-in module (PIB02)

•LED indication for relay, alarm and power supply ON

• Galvanically separated power supply

Type Selection

Input (voltage level)

DIB02 Terminals Y1, Y2

PIB02 Terminals 5, 7

Measuring ranges

Direct Internal resis. Max. volt.

Selectable by DIP-switch

6to 60 mV AC/DC 1 kΩ2 V

15 to 150 mV AC/DC 1 kΩ2 V

Max. voltage for 1 s 15 V

0.4 to 4 VpAC 50 kΩ50 V

Max. voltage for 1 s 100 V

MI and MP CT ranges AAC rms Max. curr.

1-ph.: 3-ph.:

MI 5 MP 3005 0.5 to 5 A 20 AAC

MI 20 MP 3020 2 to 20 A 50 AAC

MI 100 MP 3100 10 to 100 A 250 AAC

MI 500 MP 3500 50 to 500 A 750 AAC

Note:

The input voltage cannot

raise over 300 VAC/DC with

respect to ground (PIB02 only)

1-Phase True RMS AC/DC Over or Under Current

Types DIB02, PIB02

Input Specifications

DIB 02 C B23 150mV

DIB02 and PIB02 are precise

TRMS AC/DC over or under

current (selectable by DIP-

switch) monitoring relays.

The current is measured through

an external shunt. 1-phase

and 3-phase current up to

500 AAC can be monitored

connecting MI or MP current

transformers.

Owing to the built-in latch

function, the ON-position of

the relay output can be

maintained. Inhibit function

can be used to avoid relay

operation when not desired

(maintenance, transitions).

The LED's indicate the state

of the alarm and the output

relay.

DIB02 PIB02

Note:

MP3... current transformers

not suitable for under cur-

rent measurement due to

the output signal of the

device (see data sheet)

Contact input

DIB02 Terminals Z1, Y1

PIB02 Terminals 8, 9

Disabled > 10 kΩ

Enabled < 500 Ω

Latch disable >500 ms

Mounting Output Supply: 24 VDC Supply: 48 VDC Supply: 24/48 VAC Supply: 115/230 VAC

DIN-rail SPDT DIB 02 C 724 150MV DIB 02 C 748 150MV DIB 02 C B48 150MV DIB 02 C B23 150MV

Plug-in SPDT PIB 02 C 724 150MV PIB 02 C 748 150MV PIB 02 C B48 150MV PIB 02 C B23 150MV

2Specifications are subject to change without notice (19.09.06)

DIB02, PIB02

Mode of Operation

DIB02 and PIB02 monitor

both AC and DC over or

under current through an

external shunt.

When connected with MI or

MP current transformer (using

the 0.4 to 4 Vprange) they

can monitor 1-phase or 3-

phase AC current up to 500 A.

Example 1

(connection between termi-

nals Z1, Y1 or 8, 9 - latching

function enabled)

The relay operates and latch-

es in operating position

when the measured value

exceeds (or drops below) the

set level for morethan the

set delay time.

Provided that the current has

dropped below (or has

exceeded) the set point (see

hysteresis setting), the relay

releases when the intercon-

nection between terminals

Z1, Y1 or 8, 9 is interrupted

or the power supply is inter-

rupted as well.

The red LED flashes until the

delay time has expired or the

measured value comes back

to a non-alarm value (see

hysteresis setting).

Example 2 (MI CT)

(no connection between ter-

minals Z1, Y1 or 8, 9 - latch

function disabled)

The relay operates when the

current flowing in the CT

exceeds (or drops below) the

set level for morethan the

set delay time.

It releases when the current

drops below (or exceeds) the

set level (see hysteresis set-

ting) or when power supply

is interrupted.

Example 3 (MP CT)

(no connection between ter-

minals Z1, Y1 or 8, 9 - latch

function disabled - over cur-

rent measurement)

The relay operates when the

maximum current flowing in

the CT exceeds the set level

for more than the set delay

time.

It releases when the maxi-

mum current drops below

the set level (see hysteresis

setting) or when power sup-

ply is interrupted.

Note

When the inhibit contact is

opened, if the input signal is

already in alarm position, the

delay time needs to elapse

before relay activation.

Power supply Overvoltage cat. III

Rated operational voltage (IEC 60664, IEC 60038)

through terminals:

A1, A2 or A3, A2 (DIB02)

2, 10 or 11, 10 (PIB02)

724: 24 VDC ± 20%, insulated

748: 48 VDC ± 20%, insulated

B48: 24/48 VAC ± 15%

45 to 65 Hz, insulated

B23: 115/230 VAC ± 15%

45 to 65 Hz, insulated

Dielectric voltage DC supply AC supply

Supply to input 2 kV 4 kV

Supply to output 4kV 4kV

Input to output 4kV 4 kV

Rated operational power

AC 4 VA

DC 3 W

Supply Specifications

Power ON delay 1s± 0.5 s or 6 s ± 0.5 s

Reaction time (input signal variation from

-20% to +20% or from

+20% to -20% of set value)

Alarm ON delay < 100 ms

Alarm OFF delay < 100 ms

Accuracy (15 min warm-up time)

Temperature drift ± 1000 ppm/°C

Delay ON alarm ± 10% on set value ± 50 ms

Repeatability ± 0.5% on full-scale

Indication for

Power supply ON LED, green

Alarm ON LED, red (flashing 2 Hz

during delay time)

Output relay ON LED, yellow

Environment (EN 60529)

Degree of protection IP 20

Pollution degree 3 (DIB02), 2 (PIB02)

Operating temperature -20 to 60°C, R.H. < 95%

Storage temperature -30 to 80°C, R.H. < 95%

Housing

Dimensions DIB02 22.5 x 80 x 99.5 mm

PIB02 36 x 80 x 94 mm

Weight Approx. 150 g

Screw terminals

Tightening torque Max. 0.5 Nm

acc. to IEC 60947

Approvals UL, CSA (except 748)

CE Marking Yes

EMC

Electromagnetic Compatibillity

Immunity According to EN 61000-6-2

Emission According to EN 61000-6-3

General Specifications

Output SPDT relay

Rated insulation voltage 250 VAC

Contact ratings (AgSnO2)µ

Resistive loads AC 1 8 A @ 250 VAC

DC 12 5 A @ 24 VDC

Small inductive loads AC 15 2.5 A @ 250 VAC

DC 13 2.5 A @ 24 VDC

Mechanical life ≥30 x 106operations

Electrical life ≥105operations

(at 8 A, 250 V, cos ϕ=1)

Operating frequency ≤7200 operations/h

Dielectric strength

Dielectric voltage

≥2kVAC (rms)

Rated impulse withstand volt. 4 kV (1.2/50 µs)

Output Specifications

Specifications are subject to change without notice (19.09.06) 3

DIB02, PIB02

Function/Range/Level and Time Delay Setting

Adjust the measuring range set-

ting the DIP switches 1 and 2

and select the desired function

setting the DIP switches 3 to 6

as shown below.

oaccess the DIP switches

open the grey plastic cover as

shown below.

Selection of level and time

delay:

Upper knob:

Setting of hysteresis on rela-

tive scale: 0 to 30% on set

value.

Centre knob:

Current level setting on rela-

tive scale: 10 to 110% on full

scale.

Lower knob:

Setting of delay on alarm time

on absolute scale (0.1 to 30 s).

Measuring range

ON ON: 6 to 60 mV AC/DC

OFF ON: 15 to 150 mV AC/DC

ON OFF: 0.4 to 4 Vp

Relay working mode

ON: Normally De-Energized

OFF: Normally Energized

Power ON delay

ON: 6 s ± 0.5 s

OFF: 1 s ± 0.5 s

Contact input

ON: Latch function enable

OFF: Inhibit function enable

Monitoring function

ON: Over current

OFF: Under current

Operation Diagrams

Over current - N.D. relay

Under current - N.D. relay

Under current - Latch function - N.D. relay

Over current - Inhibit function - N.D. relay

4Specifications are subject to change without notice (19.09.06)

DIB02, PIB02

28.5

22.5

83.5

99.5

28.5

Dimensions

DIN-rail Plug-in

Wiring Diagrams

DIB02 PIB02