PRODUCT DESCRIPTION
Freez-It® is engineered for locating thermal
intermittent electrical components and cooling printed
circuit boards. This circuit refrigerant system is
nonflammable, residue-free and provides fast cooling
action.
Nonflammable
High heat transfer
Low static generation
Non-corrosive
Lowers temperature to -60°F (51°C)
Ultra pure, filtered to <0.2 microns
Leaves no residue
Nonabrasive on most surfaces
Contains no CFCs or HCFCs
TYPICAL APPLICATIONS
Freez-It® can be used to:
Cool Equipment for Testing
Dissipate Heat While Soldering or
Desoldering
Isolate Thermal Intermittent Components
Test Circuit Traces for Continuity
Test Printed Circuit Boards for Stress
Fractures
Track Intermittent Failures and Shorts
TYPICAL PRODUCT DATA AND PHYSICAL
PROPERTIES
Boiling Point -15.7°F
Vapor Density (air=1)
@ 77°F
3.18
Solubility in Water
@ 77°F /1 atm 0.10% by weight
Specific Gravity
(water = 1 @77°F) 1.21
Evaporation Rate >1
(butyl acetate=1)
Appearance Clear, Colorless
Liquified Gas
Odor Slight Ethereal
Surface Tension
(dynes/cm @ 77°F) 7.8
Flash Point (TCC) None
Shelflife 5 years
RoHS/WEEE
Status
COMPATIBILITY
Freez-It® is generally compatible with most materials
used in printed circuit board fabrication, including
sensitive plastics and compounds. With any circuit
refrigerant, compatibility must be determined on a
non-critical area prior to use.
TDS # 1050
CHEMTRONICS®
Technical Data Sheet
Freez-It®
Material Compatibility
Buna-N Fair
Graphite Good
HDPE Good
LDPE Good
Lexan™ Poor
Neoprene Good
Cross-Linked PE Good
Polyacrylate Poor
Polystyrene Good
PVC Good
Silicone Rubber Fair
Teflon™ Good
Viton™ Poor
Competitive Assessment of Freez-It®
Chemtronics
Freez-It
33% Less
Static
Competitor’s
Freeze Spray
0 20 40 60 80 100 120
% Static Generation
USAGE INSTRUCTIONS
For industrial use only.
Read MSDS carefully prior to use.
No special surface preparation is required prior to
using Freez-It®. Direct spray onto the area to
instantly cool components, circuit boards or
adhesives. For optimum performance and pin point
control, use
Freez-It® with the attached extension tube.
AVAILABILITY
ES1050 10 oz. Aerosol
ES1550 15 oz. Aerosol
TECHNICAL & APPLICATION
ASSISTANCE
Chemtronics® provides a technical hotline to answer
your technical and application related questions. The
toll free number is:
1-800-TECH-401.
ENVIRONMENTAL IMPACT DATA
ENVIRONMENTAL IMPACT DATA
CFC 0.0% VOC 0.0%
HCFC 0.0% HFC 100.0%
CL Solv. 0.0% ODP 0.0
CFC, HCFC, CL. SOLV., VOC, and HFC numbers
shown are the content by weight. Ozone depletion
potential (ODP) is determined in accordance with the
Montreal Protocol and U.S. Clean Air Act of 1990.
The ODP of this product is 0.0. It is the sum of the
ODP of the substances that may contribute to the
depletion of stratospheric ozone, based upon the
weight of each substance in the product’s
formulation.
NOTE:
This information is believed to be accurate. It is
intended for professional end users having the skills
to evaluate and use the data properly.
CHEMTRONICS® does not guarantee the accuracy
of the data and assumes no liability in connection
with damages incurred while using it.
MANUFACTURED BY:
ITW CHEMTRONICS
8125 COBB CENTER DRIVE
KENNESAW, GA 30152
1-770-424-4888 REV. E (06/06)
DISTRIBUTED BY:
