ITR8102 Features Fast response time High analytic High sensitivity Pb free This product itself will remain within RoHS compliant version Compliance with EU REACH Description The ITR8102 consist of an infrared emitting diode and an NPN silicon phototransistor, encased side-by-side on converging optical axis in a black thermoplastic housing The phototransistor receives radiation from the IR LED only .This is the normal situation. But when an object is in between, phototransistor could not receives the radiation. For additional component information , please refer to IR908-7C and PT908-7C. Applications Mouse Copier Switch Scanner Floppy disk driver Non-contact Switching For Direct Board 1 Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 www.everlight.com DATASHEET Opto Interrupter ITR8102 Device Selection Guide Part Category Chip Material Lens Color IR908-7C GaAlAs Water Clear PT908-7C Silicon Water Clear Absolute Maximum Ratings (Ta=25) Input Output Parameter Power Dissipation at(or below) 25 Free Air Temperature Reverse Voltage Forward Current Collector Power Dissipation Collector Current Collector-Emitter Voltage Emitter-Collector Voltage Operating Temperature Storage Temperature Lead Soldering Temperature (*1) (3mm from the package) Note: (*1) Soldering time5 sec. Symbol Ratings Unit Pd 75 mW VR IF Pc IC B VCEO B VECO Topr Tstg 5 50 75 30 30 5 -25~+85 -40~+85 V mA mW mA V V Tsol 260 Electro-Optical Characteristics (Ta=25) Parameter Symbol Min. Typ. Max. Unit Forward Voltage VF --1.2 1.5 V Input Reverse Current IR ----10 A Peak Wavelength P --- 940 --nm Dark C urrent ICEO ----100 nA Output C-E Saturation VCE(sat) ----0.4 V Voltage Collect Current Transfer Characteristics Rise time Fall time 2 IC(ON) 0.9 --- 15 mA tr --- 15 --- sec tf --- 15 --- sec Conditions IF=20mA VR=5V IF=20mA VCE=20V,Ee=0mW/cm2 IC=0.9mA, IF=20mA Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 VCE=5V IF=20mA VCE=5V IC=1mA RL=1K www.everlight.com DATASHEET Opto Interrupter ITR8102 Typical Electrical/Optical/Characteristics Curves for IR Forward Current vs. Ambient Temperature Spectral Sensitivity Forward Current vs. Forward Voltage 3 Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 www.everlight.com DATASHEET Opto Interrupter ITR8102 Typical Electrical/Optical/Characteristics Curves for PT Spectral Sensitivity 4 Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 www.everlight.com DATASHEET Opto Interrupter ITR8102 Package Dimension Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions 0.3mm 3.Lead spacing is measured where the lead emerge from the package 5 Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 www.everlight.com DATASHEET Opto Interrupter ITR8102 Packing Quantity Specification 1. 20PCS/1Tube, 100 Tube /1Boxe 2. 4Boxes/1Carton Label Form Specification CPN: Customer's Product Number P/N: Product Number QTY: Packing Quantity CAT: Luminous Intensity Rank HUE: Dom. Wavelength Rank REF: Forward Voltage Rank LOT No: Lot Number X: Month Reference: Identify Label Number Notes Lead Forming 1. During lead frame bending, the lead frame should be bent at a distance more than 3mm from bottom of the epoxy. Note: Must fix lead frame and do not touch epoxy before bending to avoid Photo Interrupter broken. 2. Lead forming should be done before soldering. 3. Avoid stressing the Photo Interrupter package during leads forming. The stress to the base may damage the characteristics of Photo Interrupter, or it may break the Photo Interrupter. 4. Cut the Photo Interrupter lead frame at room temperature. Cutting the lead frame at high temperatures may cause failure of the Photo Interrupter. 5. When mounting the Photo Interrupter onto a PCB, the PCB holes must be aligned exactly with the lead position of the Photo Interrupter. If the Photo Interrupter are mounted with stress at the leads, it causes deterioration of the epoxy resin and this will degrade the Photo Interrupter. Storage 1. The Photo Interrupter should be stored at 10~30C and 70%RH or less after being shipped from Everlight and the storage life limits are 3 months. If the Photo Interrupter are stored for 3 months or more, they can be stored at 10C~25C and 20%RH~60%RH for a year in a sealed container with a nitrogen atmosphere. After opening the package, the devices must be stored at 10C~25C and 20%RH~60%RH, and suggested to be used within 24 hours or as soon as possible. Besides, suggest that the remaining devices seal in the package bag as soon as possible please. 2. Please avoid rapid transitions in ambient temperature, especially in high humidity environments where condensation can occur. 6 Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 www.everlight.com DATASHEET Opto Interrupter ITR8102 Soldering 1. Careful attention should be paid during soldering. When soldering, leave more than 3mm from solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended. 2. Recommended soldering conditions: Hand Soldering DIP Soldering Temp. at tip of iron 300C Max. (30W Max.) Preheat temp. 100C Max. (60 sec Max.) Soldering time Distance 3 sec Max. 3mm Min.(From solder joint to epoxy bulb) Bath temp. & time Distance 260 Max., 5 sec Max 3mm Min. (From solder joint to epoxy bulb) 3. Recommended soldering profile laminar wave Fluxing Prehead 4. Avoiding applying any stress to the lead frame while the Photo Interrupter are at high temperature particularly when soldering. 5. Dip and hand soldering should not be done more than one time 6. After soldering the Photo Interrupter, the epoxy bulb should be protected from mechanical shock or vibration until the Photo Interrupter return to room temperature. 7. A rapid-rate process is not recommended for cooling the Photo Interrupter down from the peak temperature. 8. Although the recommended soldering conditions are specified in the above table, dip or hand soldering at the lowest possible temperature is desirable for the Photo Interrupter. 9. Wave soldering parameter must be set and maintain according to recommended temperature and dwell time in the solder wave. Cleaning Do not clean the Photo Interrupter by the ultrasonic. Heat Management 1. Heat management of Photo Interrupter must be taken into consideration during the design stage of Photo Interrupter application. The current should be de-rated appropriately by referring to the de-rating curve found in each product specification. 2. The temperature surrounding the Photo Interrupter in the application should be controlled. 7 Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 www.everlight.com DATASHEET Opto Interrupter ITR8102 ESD (Electrostatic Discharge) 1. The products are sensitive to static electricity or surge voltage. ESD can damage a die and its reliability. 2. When handling the products, the following measures against electrostatic discharge are strongly recommended: Eliminating the charge Grounded wrist strap, ESD footwear, clothes and floors Grounded workstation equipment and tools ESD table/shelf mat made of conductive materials 3. Proper grounding is required for all devices, equipment, and machinery used in product assembly. Surge protection should be considered when designing of commercial products. 4. If tools or equipment contain insulating materials such as glass or plastic, the following measures against electrostatic discharge are strongly recommended: Dissipating static charge with conductive materials Preventing charge generation with moisture Neutralizing the charge with ionizers DISCLAIMER 1. EVERLIGHT reserves the right(s) on the adjustment of product material mix for the specification. 2. The product meets EVERLIGHT published specification for a period of twelve (12) months from date of shipment. 3. The graphs shown in this datasheet are representing typical data only and do not show guaranteed values. 4. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from the use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 5. These specification sheets include materials protected under copyright of EVERLIGHT. Reproduction in any form is prohibited without obtaining EVERLIGHT's prior consent. 6. This product is not intended to be used for military, aircraft, automotive, medical, life sustaining or life saving applications or any other application which can result in human injury or death. Please contact authorized Everlight sales agent for special application request. 8 Copyright (c) 2010, Everlight All Rights Reserved. Release Date : 2016/11/26. Issue No: DRX-0000139 Rev.5 www.everlight.com